Comparison of mass transfer effects in the heterogeneously catalysed hydrogenation of phenyl acetylene in heptane and an ionic liquid

The selective heterogeneous catalytic reduction of phenyl acetylene to styrene over palladium supported on calcium carbonate is reported in both an ionic liquid and a molecular solvent. By using a rotating disc reactor in conjunction with results from a stirred tank reactor it is possible, for the first time, to disentangle the mass transfer contributions in the ionic liquid system. For both heptane and 1-butyl-3-methyl imidazolium bis{(trifluoromethyl)sulfonyl}imide, the reaction in the rotating disc reactor is dominated by reaction in the entrained film on the disc compared with very limited reaction in the bulk liquid. The lower reaction rate obtained in the ionic liquid compared with the organic solvent is shown to be due to the slow transport of the hydrogen dissolved in the liquid. It is clear from the results presented herein that, although the hydrodynamics of similar reactors used for biological treatment of wastewater are well understood, on using a more viscous fluid and higher rotation speeds necessary for fine chemical catalysis these simple relationships breakdown.

Macroturbulent and rotational broadening in the spectra of B-type supergiants.

The absorption-line spectra of early B-type supergiants show significant broadening that implies that an additional broadening mechanism (characterized here as `macroturbulence') is present in addition to rotational broadening. Using high-resolution spectra with signal-to-noise ratios of typically 500, we have attempted to quantify the relative contributions of rotation and macroturbulence, but even with data of this quality significant problems were encountered. However, for all our targets, a model where macroturbulence dominates and rotation is negligible is acceptable; the reverse scenario leads to poor agreement between theory and observation. Additionally, there is marginal evidence for the degree of broadening increasing with line strength, possibly a result of the stronger lines being formed higher in the atmosphere. Acceptable values of the projected rotational velocity are normally less than or equal to 50 km s-1, which may also be a typical upper limit for the rotational velocity. Our best estimates for the projected rotational velocity are typically 10-20 km s-1 and hence compatible with this limit. These values are compared with those predicted by single star evolutionary models, which are initially rapidly rotating. It is concluded that either these models underestimate the rate of rotational breaking or some of the targets may be evolving through a blue loop or are binaries.

A Be star with a low nitrogen abundance in the SMC cluster NGC330

High- resolution UVES/ VLT spectra of B 12, an extreme pole- on Be star in the SMC cluster NGC 330, have been analysed using non-LTE model atmospheres to obtain its chemical composition relative to the SMC standard star AV304. We find a general underabundance of metals which can be understood in terms of an extra contribution to the stellar continuum due to emission from a disk which we estimate to be at the similar to 25% level. When this is corrected for, the nitrogen abundance for B12 shows no evidence of enhancement by rotational mixing as has been found in other non-Be B-type stars in NGC 330, and is inconsistent with evolutionary models which include the effects of rotational mixing. A second Be star, NGC330-B 17, is also shown to have no detectable nitrogen lines. Possible explanations for the lack of rotational mixing in these rapidly rotating stars are discussed, one promising solution being the possibility that magnetic fields might inhibit rotational mixing.

Entanglement generation in harmonic chains: Tagging by squeezing

We address the problem of springlike coupling between bosons in an open-chain configuration where the counter-rotating terms are explicitly included. We show that fruitful insight can be gained by decomposing the time-evolution operator of this problem into a pattern of linear-optics elements. This allows us to provide a clear picture of the effects of the counter-rotating terms in the important problem of long-haul entanglement distribution. The analytic control over the variance matrix of the state of the bosonic register allows us to track the dynamics of the entanglement. This helps in designing a global addressing scheme, complemented by a proper initialization of the register, which quantitatively improves the entanglement between the extremal oscillators in the chain, thus providing a strategy for feasible long-distance entanglement distribution.

The VLT-FLAMES survey of massive stars: mass loss and rotation of early-type stars in the SMC

We have studied the optical spectra of a sample of 31 O- and early B-type stars in the Small Magellanic Cloud, 21 of which are associated with the young massive cluster NGC 346. Stellar parameters are determined using an automated fitting method (Mokiem et al. 2005, A&A, 441, 711), which combines the stellar atmosphere code FASTWIND (Puls et al. 2005, A&A, 435, 669) with the genetic algorithm based optimisation routine PIKAIA (Charbonneau 1995, ApJS, 101, 309). Comparison with predictions of stellar evolution that account for stellar rotation does not result in a unique age, though most stars are best represented by an age of 1-3 Myr. The automated method allows for a detailed determination of the projected rotational velocities. The present day v(r) sin i distribution of the 21 dwarf stars in our sample is consistent with an underlying rotational velocity (v(r)) distribution that can be characterised by a mean velocity of about 160-190 km s(-1) and an effective half width of 100-150 km s(-1). The vr distribution must include a small percentage of slowly rotating stars. If predictions of the time evolution of the equatorial velocity for massive stars within the environment of the SMC are correct (Maeder & Meynet 2001, A&A, 373, 555), the young age of the cluster implies that this underlying distribution is representative for the initial rotational velocity distribution. The location in the Hertzsprung-Russell diagram of the stars showing helium enrichment is in qualitative agreement with evolutionary tracks accounting for rotation, but not for those ignoring vr. The mass loss rates of the SMC objects having luminosities of log L-star/L-circle dot greater than or similar to 5.4 are in excellent agreement with predictions by Vink et al. (2001, A&A, 369, 574). However, for lower luminosity stars the winds are too weak to determine. M accurately from the optical spectrum. Three targets were classified as Vz stars, two of which are located close to the theoretical zero-age main sequence. Three lower luminosity targets that were not classified as Vz stars are also found to lie near the ZAMS. We argue that this is related to a temperature effect inhibiting cooler from displaying the spectral features required for the Vz luminosity class.

Dynamic, in situ optical, magnetic and magneto-optical monitoring of the growth of Co/Au and Pd/Co/Au multilayer systems

The growth of magnetron sputtered Co/Au and Pd/Co/Au superlattices on Au and Pd buffer layers, deposited onto glass substrates, has been monitored optically and magneto-optically in real time, using rotating analyser ellipsometry and Kerr polarimetry, at a wavelength of 633 nm. The magneto-optical traces, combined with ex situ and in situ hysteresis loops, provide a detailed and informative fingerprint of the optical and magnetic properties of the films as they evolve during growth. For Co/Au, oscillations in the polar magneto-optical effect developed during the deposition of An overlayers on Co and these may be attributed to quantum well states. However, the hysteresis measurements show that the magnetic field required to maintain saturation magnetization throughout the experiment was larger than available in situ, introducing a degree of confusion concerning the interpretation of the data. This problem was overcome by the incorporation of Pd layers into the Co/Au structure, thereby eliminating variation in magnetic orientation during growth of the Au layers as a contributory factor to the observations.

Polarisation analysis of VUV synchrotron radiation emitted from a bending magnet source in the energy range 20-50 eV: A comparison between measurements and theoretical predictions

The results of a study to characterise the polarisation properties of the photon beam emerging from beamline 5D, mounted on a bending magnet source at the Synchrotron Radiation Source, Daresbury Laboratory, are presented. The expectation values for the Stokes parameters corresponding to the light transmitted by the beamline have been calculated by combining ray-tracing and optical methods. The polarisation of the light at the source is modified both by the beamline geometry and by the reflections at the optical components. Although it is often assumed that the polarising properties of grazing incidence optics are negligible, this assumption leads to rather inaccurate results in the VUV region. A study of the reflectivity shows that even at incidence angles (theta(i) = 80-85degrees) which are far from the Brewster angle (theta(B) similar to 45degrees for VUV and soft X-ray radiation) the residual changes in the amplitudes of the reflected light can result in non-negligible polarisation effects. Furthermore, reflection at grazing incidence gives rise to a substantial change in the phase, and this has the effect of rotating the elliptically polarised state. Theoretical Stokes parameters have been compared with full polarisation measurements obtained using a reflection polarimeter in the energy range 20-40 eV. (C) 2003 Elsevier B.V. All rights reserved.

Influence of mix proprtions on rheolgy of cement grouts containing limestone powder

In this paper the parameters of cement grout affecting rheological behaviour and compressive strength are investigated. Factorial experimental design was adopted in this investigation to assess the combined effects of the following factors on fluidity, rheological properties, induced bleeding and compressive strength: water/binder ratio (W/B), dosage of superplasticiser (SP), dosage of viscosity agent (VA), and proportion of limestone powder as replacement of cement (LSP). Mini-slump test, Marsh cone, Lombardi plate cohesion meter, induced bleeding test, coaxial rotating cylinder viscometer were used to evaluate the rheology of the cement grout and the compressive strengths at 7 and 28 days were measured. A two-level fractional factorial statistical model was used to model the influence of key parameters on properties affecting the fluidity, the rheology and compressive strength. The models are valid for mixes with 0.35-0.42 W/B, 0.3-1.2% SP, 0.02-0.7% VA (percentage of binder) and 12-45% LSP as replacement of cement. The influences of W/B, SP, VA and LSP were characterised and analysed using polynomial regression which can identify the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, inducing bleeding, yield value, plastic viscosity and compressive strength as function of W/B, SP, VA and proportion of LSP. The statistical approach used highlighted the limestone powder effect and the dosage of SP and VA on the various rheological characteristics of cement grout

The VLT-FLAMES survey of massive stars: atmospheric parameters and rotational velocity distributions for B-type stars in the Magellanic Clouds

Aims.We aim to provide the atmospheric parameters and rotational velocities for a large sample of O- and early B-type stars, analysed in a homogeneous and consistent manner, for use in constraining theoretical models. Methods: Atmospheric parameters, stellar masses, and rotational velocities have been estimated for approximately 250 early B-type stars in the Large (LMC) and Small (SMC) Magellanic Clouds from high-resolution VLT-FLAMES data using the non-LTE TLUSTY model atmosphere code. This data set has been supplemented with our previous analyses of some 50 O-type stars (Mokiem et al. 2006, 2007) and 100 narrow-lined early B-type stars (Hunter et al. 2006; Trundle et al. 2007) from the same survey, providing a sample of ~400 early-type objects. Results: Comparison of the rotational velocities with evolutionary tracks suggests that the end of core hydrogen burning occurs later than currently predicted and we argue for an extension of the evolutionary tracks. We also show that the large number of the luminous blue supergiants observed in the fields are unlikely to have directly evolved from main-sequence massive O-type stars as neither their low rotational velocities nor their position on the H-R diagram are predicted. We suggest that blue loops or mass-transfer binary systems may populate the blue supergiant regime. By comparing the rotational velocity distributions of the Magellanic Cloud stars to a similar Galactic sample, we find that (at 3s confidence level) massive stars (above 8 M?) in the SMC rotate faster than those in the solar neighbourhood. However there appears to be no significant difference between the rotational velocity distributions in the Galaxy and the LMC. We find that the v sin i distributions in the SMC and LMC can modelled with an intrinsic rotational velocity distribution that is a Gaussian peaking at 175 km s-1 (SMC) and 100 km s-1 (LMC) with a 1/e half width of 150 km s-1. We find that in NGC 346 in the SMC, the 10-25 M? main-sequence stars appear to rotate faster than their higher mass counterparts. It is not expected that O-type stars spin down significantly through angular momentum loss via stellar winds at SMC metallicity, hence this could be a reflection of mass dependent birth spin rates. Recently Yoon et al. (2006) have determined rates of GRBs by modelling rapidly rotating massive star progenitors. Our measured rotational velocity distribution for the 10-25 M? stars is peaked at slightly higher velocities than they assume, supporting the idea that GRBs could come from rapid rotators with initial masses as low as 14 M? at low metallicities.

The manufacture and characterisation of hot-melt extruded enteric tablets

The aim of this highly novel study was to use hot-melt extrusion technology as an alternative process to enteric coating. In so doing, oral dosage forms displaying enteric properties may be produced in a continuous, rapid process, providing significant advantages over traditional pharmaceutical coating technology. Eudragit (R) L100-55, an enteric polymer, was pre-plasticized with triethyl citrate (TEC) and citric acid and subsequently dry-mixed with 5-aminosalicylic acid, a model active pharmaceutical ingredient (API), and an optional gelling agent (PVP (R) K30 or Carbopol (R) 971P). Powder blends were hot-melt extruded as cylinders, cut into tablets and characterised using powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC) and dissolution testing conducted in both pH 1.2 and pH 6.8 buffers. Increasing the concentration of TEC significantly lowered the glass transition temperature (T,) of Eudragit (R) L100-55 and reduced temperatures necessary for extrusion as well as the die pressure. Moreover, citric acid (17% w/w) was shown to act as a solid-state plasticizer. HME tablets showed excellent gastro-resistance, whereas milled extrudates compressed into tablets released more than 10% w/w of the API in acidic media. Drug release from HME tablets was dependent upon the concentration of TEC, the presence of citric acid, PVP K30, and Carbopol (R) 971P in the matrix, and pH of the dissolution media. The inclusion of an optional gelling agent significantly reduced the erosion of the matrix and drug release rate at pH 6.8; however, the enteric properties of the matrix were lost due to the formation of channels within the tablet. Consequently this work is both timely and highly innovative and identifies for the first time a method of producing an enteric matrix tablet using a continuous hot-melt extrusion process.

Element suitability for circularly polarised phase agile reflectarray applications

The electrical characteristics of various elements that can be used as spatial phase shifters in circularly polarised (CP) reflectarrays are contrasted. The elements investigated are; a single rotating dipole at 10.3 GHz; a multiple dipole at 18.2 GHz; a rotating stub at 2.8 GHz; and a periphery point short-circuited circular patch at 3.0 GHz. For each element type, results are presented for the reflection phase, polarisation purity and reflection loss. Where appropriate, experiments are performed using the waveguide simulator technique to validate the numerical EM simulation.

Imaging the cool stars in the interacting binaries AE Aqr, BV Cen and V426 Oph

It is well known that magnetic activity in late-type stars increases with increasing rotation rate. Using inversion techniques akin to medical imaging, the rotationally broadened profiles from such stars can be used to reconstruct `Doppler images' of the distribution of cool, dark starspots on their stellar surfaces. Interacting binaries, however, contain some of the most rapidly rotating late-type stars known and thus provide important tests of stellar dynamo models. Furthermore, magnetic activity is thought to play a key role in their evolution, behaviour and accretion dynamics. Despite this, we know comparatively little about the magnetic activity and its influence on such binaries. In this review we summarise the concepts behind indirect imaging of these systems, and present movies of the starspot distributions on the cool stars in some interacting binaries. We conclude with a look at the future opportunities that such studies may provide.

Roche tomography of cataclysmic variables - III. Star-spots on AE Aqr

We present a Roche tomography reconstruction of the secondary star in the cataclysmic variable AE Aqr. The tomogram reveals several surface inhomogeneities that are due to the presence of large, cool star-spots. In addition to a number of lower latitude spots, the maps also show the presence of a large, high-latitude spot similar to that seen in Doppler images of rapidly rotating isolated stars, and a relative paucity of spots at a latitude of 40 degrees. In total, we estimate that some 18 per cent of the Northern hemisphere of AE Aqr is spotted.

Effect of rudder angle on propeller wash velocities at a seabed

This paper deals with an experimental investigation into the velocity distribution downstream of a propeller, operating at bollard pull conditions and in the presence of a mobile sediment bed. Previous investigations either ignored the effect of a rudder in the wash or considered only its influence on an unconfined jet. The velocity profiles within the jet produced by a rotating propeller with a rudder present were measured at a mobile bed and compared to currently available predictive equations. The velocity distribution profiles in the jet, influenced by bed proximity, were found not to comply with current predictive methods. The velocity distributions measured within the jet were found to be complex and non-symmetrical. To provide a basic velocity predictive tool, a neural network analysis toolbox within Matlab was utilised and trained using the experimental data.

The Architecture of Seduction: An Analysis on Digital Architectures within Consumer Society

Currently new digital tools used in architecture are often at the service of a conception of architecture as a consumer society’s cultural good. Within this neoliberal cultural frame, architects’ social function is no longer seen as the production of urban facts with sense of duty, but as a part within the symbolic logic that rules the social production of cultural values as it was defined by Veblen and developed by Baudrillard. As a result, the potential given by the new digital tools used in representation has shifted from an instrument used to verify a built project to two different main models: At the one hand the development of pure virtual architectures that are exclusively configured within their symbolic value as artistic “images” easily reproducible. On the other hand the development of all those projects which -even maintaining their attention to architecture as a built fact- base their symbolic value on the author’s image and on virtual aesthetics and logics that prevail over architecture’s materiality. Architects’ sense of duty has definitely reached a turning point.