Control of Large-size SiC Growth Process Using Modeling tool

Large size bulk silicon carbide (SiC) crystals are commonly grown by the physical vapor transport (PVT) method. The PVT growth of SiC crystals involves sublimation and condensation, chemical reactions, stoichiometry, mass transport, induced thermal stress, as well as defect and micropipes generation and propagation. The quality and polytype of as-grown SiC crystals are related to the temperature distribution inside the growth chamber during the growth process, it is critical to predict the temperature distribution from the measured temperatures outside the crucible by pyrometers. A radio-frequency induction-heating furnace was used for the growth of large-size SiC crystals by the PVT method in the present study. Modeling and simulation have been used to develop the SiC growth process and to improve the SiC crystal quality. Parameters such as the temperature measured at the top of crucible, temperature measured at the bottom of the crucible, and inert gas pressure are used to control the SiC growth process. By measuring the temperatures at the top and bottom of the crucible, the temperatures inside the crucible were predicted with the help of modeling tool. SiC crystals of 6H polytype were obtained and characterized by the Raman scattering spectroscopy and SEM, and crystals of few millimeter size grown inside the crucible were found without micropipes. Expansion of the crystals were also performed with the help of modeling and simulation.

Influence of Wind and Grain Size on Migration of Asymmetric Sand Waves

Large parts of shallow seas are covered by regular seabed patterns and sand wave is one kind of these patterns. The instability of the sedimentary structures may hazard pipelines and the foundations of offshore structures. In the last decade or so, it's a focus for engineers to investigate the movement mechanism of sand waves. Previous theoretical studies of the subject have developed a general model to predict the growth and migration of sand waves, which is based on the two-dimensional vertical shallow water equations and the bed-form deformation equations. Although the relation between wave-current flow and sand bed deformation has been established, the topographic influence has not been considered in the model. In this paper some special patterns, which are asymmetric and close to the reality, are represent as the perturbed seabed and the evolution of sand waves is calculated. The combination of a steady flow induced by wind and a sinusoidal tidal flow is considered as the basic flow. Finally the relations of some parameters (grain size, etc.) and sand waves' growth and migration are discussed, and the growth rate and migration speeds of asymmetric sand waves are carried out.

Size composition of catches of Yellowfin tuna in the Japanese long-line fishery in the eastern tropical Pacific east of 130°W

ENGLISH (pgs. 267-283): In the spring of 1963, the senior author, who is a member of the staff of the Nankai Regional Fisheries Research. Laboratory, Fisheries Agency, Japanese Government, came to the Institute of Marine Resources of the University of California as a visiting investigator, bringing with him catch statistical data from the fishery in the eastern Pacific, which had been collected at the Nankai Regional Fisheries Research Laboratory (NRFRL) through September 1962, in order to conduct studies of these data in collaboration with the junior author, and with investigators of the InterAmerican Tropical Tuna Commission. A general review of the long-line fishery, based on the catch statistics of the commercial fishing fleet has been published by Suda and Schaefer (1965). In this paper we present an analysis of data respecting the size-composition of yellowfin tuna taken on long-line gear throughout the eastern Pacific between 1958 and 1962, and make some comparisons with data on size-composition of yellowfin tuna taken in the near-surface fishery, by bait boats and purse-seiners, in waters adjacent to the American coast. As has been shown by Suda and Schaefer (1965), the long-line fishery in the eastern Pacific is primarily directed toward the capture of bigeye tuna. However, considerable quantities of yellowfin tuna are also taken on this gear, and, in addition, there are substantial catches of albacore and of several species of spearfishes in some parts of the range of this fishery. Information respecting the catch rates of yellowfin tuna, and information respecting the size-composition of the stock of yellowfin tuna being exploited by the long-line fishery, is of particular interes~" because the yellowfin tuna population of the eastern Pacific is also subject to an intensive fishery by baitboats and purse-seiners which capture this species, together with skipjack, near the surface along the coast of the Americas, and around the outlying islands, in the region of California to northern Chile. SPANISH (pgs. 311-329): En la primavera de 1963, el autor principal, quien es miembro del personal del Nankai Regional Fisheries Research Laboratory, Fisheries Agency del gobierno japonés, vino al Institute of Marine Resources de la Universidad de California en calidad de investigador visitante y trajo consigo datos estadísticos de las capturas de la pesquería en el Pacífico oriental, que habían sido recolectados en el Nankai Regional Fisheries Research Laboratory (NRFRL) hasta septiembre de 1962, con el fin de hacer estudios de esos datos en colaboración con el coautor y con investigadores de la Comisión Interamericana del Atún Tropical. Una revisión general de la pesquería con palangre, basada sobre las estadísticas de captura de la flota pesquera comercial, ha sido publicada por Suda y Schaefer (1965). En este trabajo presentamos un análisis de los datos correspondientes a la composición de tamaños del atún aleta amarilla capturado con equipo palangrero en todo el Pacífico oriental, entre 1958 y 1962, y hacemos algunas comparaciones con los datos sobre la composición de tamaños del atún aleta amarilla cogido en la pesquería superficial cercana, por barcos de carnada y rederos en aguas adyacentes a la costa americana. Como ha sido demostrado por Suda y Schaefer (1965) la pesquería con palangre en el Pacífico oriental tiene como principal objeto la captura del atún ojo grande. Sin embargo, considerables cantidades de atún aleta amarilla son capturadas también por este equipo y, además, hay también considerables capturas de albacora y de diversas especies de peces-espada en algunas partes de la región que abarca esta pesquería. La información respecto a las tasas de captura del atún aleta amarilla, y la relativa a la composición de tamaños del stock de esta especie que explota la pesquería con palangre, es de particular interés, a causa de que la población de atún aleta amarilla del Pacífico oriental es también objeto de una pesca intensiva por barcos de carnada y rederos que capturan esta especie, junto con el barrilete, cerca de la superficie a 10 largo de la costa de las Américas y alrededor de las islas mar afuera, en la región desde California hasta el norte de Chile.

Edge and Size Effects in Micro Composite Structure

Because of the load transfer effect of interface layer, the stress distribution inside the composite structure of film/substrate can be very different from the Timoshenko's model. In this paper, we give the derivation and analysis of such load transfer effect of shear-lag (S-L) model. The micro-structure size (boundary conditions) effect together with interface load transfer effect becomes more and more important as the microstructure size including the three dimensions of thickness, width and length shrinks. The microstructure size is also responsible for the so-called edge-induced stress. The edge effect and difference of S-L model and Timoshenko model are also demonstrated.

Reducing non-point DOC and nitrogen exports from rice fields: A pilot study and quantitative survey to determine the effects of different hydrologic management practices : Deliverable 15.3 Final Report

Rice cultivation at any level in the Sacramento–San Joaquin Delta (existing or expanded) compels the need to quantify surface and subsurface loads of dissolved organic carbon (DOC), disinfection byproduct precursors (DBPPs) and nitrogen. This information can be used to develop Best Management Practices (BMPs) to reduce export of these constituents in order to improve drinking water quality. Although rice cultivation in the Delta is relatively limited, several factors outside of this research could contribute to increased rice acreage in the Delta: • Recently developed rice varieties seem more suitable for the Delta climate than earlier varieties which required warmer conditions; • Previous economic analyses (Appendix A.10) suggest rice is more profitable than corn, a dominant land use in the Delta; • Recent studies on wetlands at Twitchell Island suggest rice production can help mitigate oxidative subsidence (Miller et al. 2000); • The different oxidative states that result from flooding in rice as compared to those found in crops that require drained soils may help control crop specific weeds and nematodes when rice is incorporated into a crop rotation; and • Providing flooded conditions during a greater part of the year than other crops may benefit water birds. ... (PDF contains 249 pages)

Development of a Cell Size Relaxed Scheme for the Direct Simulation Monte Carlo Method

The conventional direct simulation Monte Carlo (DSMC) method has a strong restriction on the cell size because simulated particles are selected randomly within the cell for collisions. Cells with size larger than the molecular mean free path are generally not allowed in correct DSMC simulations. However, the cell-size induced numerical error can be controlled if the gradients of flow properties are properly involved during collisions. In this study, a large cell DSMC scheme is proposed to relax the cell size restriction. The scheme is applied to simulate several test problems and promising results are obtained even when the cell size is greater than 10 mean free paths of gas molecules. However, it is still necessary, of course, that the cell size be small with respect to the flow field structures that must be resolved.

Interface cracking and particulate size effect in particle-reinforced metal-matrix composites

The mechanical behaviors of the ceramic particle-reinforced metal matrix composites are modeled based on the conventional theory of mechanism-based strain gradient plasticity presented by Huang et al. Two cases of interface features with and without the effects of interface cracking will be analyzed, respectively. Through comparing the result based on the interface cracking model with experimental result, the effectiveness of the present model can be evaluated. Simultaneously, the length parameters included in the strain gradient plasticity theory can be obtained.

Dislocations and twins in nanocrystalline Ni after severe plastic deformation: the effects of grain size

Deformation microstructures have been investigated in nanocrystalline (nc) Ni with grain sizes in the 50-100 nm range. It was found that deformation twinning started to occur in grains of similar to 90 nm, and its propensity increased with decreasing grain size. In most of the nc grains dislocations were observed as well, in the form of individual dislocations and dipoles. It is concluded that dislocation-mediated plasticity dominates for grain sizes in the upper half, i.e. 50-100 nm, of the nanocrystalline regime. (C) 2007 Published by Elsevier B.V.

Bag and size limit analyses for red drum in Northern and Southern Regions of the U.S. Atlantic

Assessments of the Atlantic red drum for the northern (North Carolina and north) and southern (South Carolina through east coast of Florida) regions along the U. S. Atlantic coast were recently completed. The joint Red Drum Technical Committee (SAFMC/ASMFC) selected the most appropriate catch matrix (incorporating an assumption on size of recreationally-released fish), selectivity of age 3 relative to age 2, and virtual population analysis (FADAPT). Given gear- and age-specific estimates of fishing mortality (F) for the 1992-1998 period, analyses were made of potential gains in escapement through age 4 and static spawning potential ratio (SPR) from further reductions in fishing mortality due to changes in slot and bag limits. Savings from bag limits were calculated given a particular slot size for the recreational fishery, with no savings for the commercial fisheries in the northern region due to their being managed primarily through a quota. Relative changes in catch-at-age estimates were used to adjust age-specific F and hence calculated escapement through age 4 and static SPR. Adjustment was made with the recreational savings to account for release mortality (10%, as in the stock assessment). Alternate runs for the northern region commercial fishery considered 25% release mortality for lengths outside the slot (instead of 0% for the base run), and 0% vs. 10% gain or loss across legal sizes in F. These results are summarized for ranges of bag limits with increasing minimum size limit (for fixed maximum size), and with decreasing maximum size limit (for fixed minimum size limit). For the southern region, a bag limit of one-fish per angler trip would be required to attain the stated target of 40% static SPR if the current slot limit were not changed. However, for the northern region, a bag limit of one-fish per angler trip appears to be insufficient to attain the stated target of 40% static SPR while maintaining the current slot limit. (PDF contains 41 pages)

Size-dependent elastic properties of Ni nanofilms by molecular dynamics simulation

Size-dependent elastic properties of Ni nanofilms are investigated by molecular dynamics ( MD) simulations with embedded atom method (EAM). The surface effects are considered by calculating the surface relaxation, surface energy, and surface stress. The Young's modulus and yield stress are obtained as functions of thickness and crystallographic orientation. It is shown that the surface relaxation has important effects on the the elastic properties at nanoscale. When the surface relaxation is outward, the Young's modulus decreases with the film thickness decreasing, and vice versa. The results also show that the yield stresses of the films increase with the films becoming thinner. With the thickness of the nanofilms decreasing, the surface effects on the elastic properties become dominant.

The surface- and size-dependent elastic moduli of nanostructures

A theoretical model is presented to investigate the size-dependent elastic moduli of nanostructures with the effects of the surface relaxation surface energy taken into consideration. At nanoscale, due to the large ratios of the surface-to-volume, the surface effects, which include surface relaxation surface energy, etc., can play important roles. Thus, the elastic moduli of nanostructures become surface- and size-dependent. In the research, the three-dimensional continuum model of the nanofilm with the surface effects is investigated. The analytical expressions of five nonzero elastic moduli of the nanofilm are derived, and then the dependence of the elastic moduli is discussed on the surface effects and the characteristic dimensions of nanofilms.

Species and size relationships within schools of yellowfin and skipjack tuna as indicated by catches in the Eastern Tropical Pacific Ocean

ENGLISH: Yellowfin tuna, Neothunnus macropterus, and skipjack tuna, Katsuwonus pelamis, are fished intensively off the west coast of the Americas in an area from about the California-Mexico border in the north to the Peru-Chile border in the south. The historical development of this fishery, and its expansion by the long-range California fleets of bait and purse-seine vessels, are well documented by Godsil (1938), Scofield (1951) and Shimada and Sehaefer (1956). The quarterly distribution of the tuna catches within this area has been reported for some recent years by Alverson (1959). SPANISH: Los atunes aleta amarilla, Neothunnus macropterus, y barrilete, Katsuwonus pelamis, son pescados con intensidad frente a la costa occidental del continente americano, en un área comprendida más o menos entre la frontera California-México en el norte y el límite Perú-Chile en el sur. El desarrollo histórico de esta pesquería y la expansión que le han dado las flotas californianas de largo radio de acción, formadas por los barcos de carnada y rederos, están bien documentados por Godsil (1938), Scofield (1951) y Shimada y Schaefer (1956). La distribución trimestral de las pescas de atún dentro de esta área ha sido tratada por Alverson (1959) con referencia a años recientes.

Size and year class composition of catch, age and growth of yellowfin tuna in the Eastern Tropical Pacific Ocean for the years 1954-1958

ENGLISH: Data on the size composition of catch for the years 1954-1958 have been studied to determine year class composition, age and growth of yellowfin tuna in the Eastern Tropical Pacific Ocean. Direct age determination of tropical tunas has not yet proven reliable; however, this analysis has shown that the length-frequency distributions themselves are adequate to determine year class structure and growth rates. Absolute age has been estimated by comparing the average time of spawning with the time at which age groups initially appear in the catch. SPANISH: Los datos sobre la composición del tamaño de la pesca durante los años 1954-1958 han sido estudiados con el objeto de determinar la composición de las clases anuales, la edad y el crecimiento del atún aleta amarilla en el Océano Pacífico Oriental Tropical. Las determinaciones directas de la edad de los atunes tropicales no han probado todavía ser de confianza; sin embargo, este análisis ha demostrado que las distribuciones de la frecuencia de las longitudes son adecuadas para determinar la estructura de las clases anuales y de las tasas de crecimiento. La edad absoluta ha sido estimada mediante la comparación de la época promedio de desove con la epoca en que los grupos de edades comienzan a aparecer en la pesca.

A video method for quantifying size distribution, density, and three-dimensional spatial structure of reef fish spawning aggregations

There is a clear need to develop fisheries independent methods to quantify individual sizes, density, and three dimensional characteristics of reef fish spawning aggregations for use in population assessments and to provide critical baseline data on reproductive life history of exploited populations. We designed, constructed, calibrated, and applied an underwater stereo-video system to estimate individual sizes and three dimensional (3D) positions of Nassau grouper (Epinephelus striatus) at a spawning aggregation site located on a reef promontory on the western edge of Little Cayman Island, Cayman Islands, BWI, on 23 January 2003. The system consists of two free-running camcorders mounted on a meter-long bar and supported by a SCUBA diver. Paired video “stills” were captured, and nose and tail of individual fish observed in the field of view of both cameras were digitized using image analysis software. Conversion of these two dimensional screen coordinates to 3D coordinates was achieved through a matrix inversion algorithm and calibration data. Our estimate of mean total length (58.5 cm, n = 29) was in close agreement with estimated lengths from a hydroacoustic survey and from direct measures of fish size using visual census techniques. We discovered a possible bias in length measures using the video method, most likely arising from some fish orientations that were not perpendicular with respect to the optical axis of the camera system. We observed 40 individuals occupying a volume of 33.3 m3, resulting in a concentration of 1.2 individuals m–3 with a mean (SD) nearest neighbor distance of 70.0 (29.7) cm. We promote the use of roving diver stereo-videography as a method to assess the size distribution, density, and 3D spatial structure of fish spawning aggregations.