General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

High-SNR analytical performance of spatial multiplexing MIMO systems with CSI

In this paper, we investigate the average andoutage performance of spatial multiplexing multiple-input multiple-output (MIMO) systems with channel state information at both sides of the link. Such systems result, for example, from exploiting the channel eigenmodes in multiantenna systems. Dueto the complexity of obtaining the exact expression for the average bit error rate (BER) and the outage probability, we deriveapproximations in the high signal-to-noise ratio (SNR) regime assuming an uncorrelated Rayleigh flat-fading channel. Moreexactly, capitalizing on previous work by Wang and Giannakis, the average BER and outage probability versus SNR curves ofspatial multiplexing MIMO systems are characterized in terms of two key parameters: the array gain and the diversity gain. Finally, these results are applied to analyze the performance of a variety of linear MIMO transceiver designs available in the literature.

Capacity of MIMO Channels: asymptotic evaluation under correlated fading

This paper investigates the asymptotic uniform power allocation capacity of frequency nonselective multiple-inputmultiple-output channels with fading correlation at either thetransmitter or the receiver. We consider the asymptotic situation,where the number of inputs and outputs increase without boundat the same rate. A simple uniparametric model for the fadingcorrelation function is proposed and the asymptotic capacity perantenna is derived in closed form. Although the proposed correlationmodel is introduced only for mathematical convenience, itis shown that its shape is very close to an exponentially decayingcorrelation function. The asymptotic expression obtained providesa simple and yet useful way of relating the actual fadingcorrelation to the asymptotic capacity per antenna from a purelyanalytical point of view. For example, the asymptotic expressionsindicate that fading correlation is more harmful when arising atthe side with less antennas. Moreover, fading correlation does notinfluence the rate of growth of the asymptotic capacity per receiveantenna with high Eb /N0.

The IST METRA Project

This article summarizes the main achievementsof the Multi-Element Transmit andReceive Antennas (METRA) Project, an ISTresearch and technological development project carried out between January 2000 and June 2001 by Universitat Politècnica de Catalunya, the Center for Personkommunikation of Aalborg University, Nokia Networks, Nokia Mobile Phones, and Vodafone Group Research and Development.The main objective of METRA was the performanceevaluation of multi-antenna terminals incombination with adaptive antennas at the basestation in UMTS communication systems. 1 AMIMO channel sounder was developed that providedrealistic multi-antenna channel measurements.Using these measured data, stochasticchannel models were developed and properly validated.These models were also evaluated inorder to estimate their corresponding channelcapacity. Different MIMO configurations andprocessing schemes were developed for both theFDD and TDD modes of UTRA, and their linkperformance was assessed. Performance evaluationwas completed by system simulations thatillustrated the benefits of MIMO configurationsto the network operator. Implementation cost vs.performance improvement was also covered bythe project, including the base station and terminalmanufacturer and network operator viewpoints.Finally, significant standards contributionswere generated by the project and presented to the pertinent 3GPP working groups.

Smart antennas in software radio base stations

The application of adaptive antenna techniques to fixed-architecture base stations has been shown to offer wide-ranging benefits, including interference rejection capabilities or increased coverage and spectral efficiency.Unfortunately, the actual implementation ofthese techniques to mobile communication scenarios has traditionally been set back by two fundamental reasons. On one hand, the lack of flexibility of current transceiver architectures does not allow for the introduction of advanced add-on functionalities. On the other hand, theoften oversimplified models for the spatiotemporal characteristics of the radio communications channel generally give rise toperformance predictions that are, in practice, too optimistic. The advent of software radio architectures represents a big step toward theintroduction of advanced receive/transmitcapabilities. Thanks to their inherent flexibilityand robustness, software radio architecturesare the appropriate enabling technology for theimplementation of array processing techniques.Moreover, given the exponential progression ofcommunication standards in coexistence andtheir constant evolution, software reconfigurabilitywill probably soon become the only costefficientalternative for the transceiverupgrade. This article analyzes the requirementsfor the introduction of software radio techniquesand array processing architectures inmultistandard scenarios. It basically summarizesthe conclusions and results obtained withinthe ACTS project SUNBEAM,1 proposingalgorithms and analyzing the feasibility ofimplementation of innovative and softwarereconfigurablearray processing architectures inmultistandard settings.

Joint array combining and MLSE for single-user receivers in multipath Gaussian multiuser channels

The well-known structure of an array combiner along with a maximum likelihood sequence estimator (MLSE) receiveris the basis for the derivation of a space-time processor presentinggood properties in terms of co-channel and intersymbol interferencerejection. The use of spatial diversity at the receiver front-endtogether with a scalar MLSE implies a joint design of the spatialcombiner and the impulse response for the sequence detector. Thisis faced using the MMSE criterion under the constraint that thedesired user signal power is not cancelled, yielding an impulse responsefor the sequence detector that is matched to the channel andcombiner response. The procedure maximizes the signal-to-noiseratio at the input of the detector and exhibits excellent performancein realistic multipath channels.

Smart antennas: state of the art

Aim of this contribution is to illustrate the state of the art of smart antenna research from several perspectives. The bow is drawn from transmitter issues via channel measurements and modeling, receiver signal processing, network aspects, technological challenges towards first smart antenna applications and current status of standardization. Moreover, some future prospects of different disciplines in smart antenna research are given.

ML estimator and hybrid beamformer for multipath and interference mitigation in GNSS receivers

This paper addresses the estimation of the code-phase(pseudorange) and the carrier-phase of the direct signal received from a direct-sequence spread-spectrum satellite transmitter. Thesignal is received by an antenna array in a scenario with interferenceand multipath propagation. These two effects are generallythe limiting error sources in most high-precision positioning applications.A new estimator of the code- and carrier-phases is derivedby using a simplified signal model and the maximum likelihood(ML) principle. The simplified model consists essentially ofgathering all signals, except for the direct one, in a component withunknown spatial correlation. The estimator exploits the knowledgeof the direction-of-arrival of the direct signal and is much simplerthan other estimators derived under more detailed signal models.Moreover, we present an iterative algorithm, that is adequate for apractical implementation and explores an interesting link betweenthe ML estimator and a hybrid beamformer. The mean squarederror and bias of the new estimator are computed for a numberof scenarios and compared with those of other methods. The presentedestimator and the hybrid beamforming outperform the existingtechniques of comparable complexity and attains, in manysituations, the Cramér–Rao lower bound of the problem at hand.

Space-time front-ends for RAKE receivers in the FDD mode of UTRA

A unified and general vision of different space-time processors is presented. Many popular receivers can beaccomodated, like V-RAKE receivers, weighted V-RAKE, or spatial narrowband beamforming. By makingappropriate assumptions on the space/time characteristic of the interference it is possible to enhance theperformance of the receiver through spatial/temporal pre-processors. These receivers will be tested in the FDDmode of UTRA.

Hybrid turbo FEC/ARQ systems and distributed space-time coding for cooperative transmission

Cooperative transmission can be seen as a "virtual" MIMO system, where themultiple transmit antennas are in fact implemented distributed by the antennas both at the source and the relay terminal. Depending on the system design, diversity/multiplexing gainsare achievable. This design involves the definition of the type of retransmission (incrementalredundancy, repetition coding), the design of the distributed space-time codes, the errorcorrecting scheme, the operation of the relay (decode&forward or amplify&forward) and thenumber of antennas at each terminal. Proposed schemes are evaluated in different conditionsin combination with forward error correcting codes (FEC), both for linear and near-optimum(sphere decoder) receivers, for its possible implementation in downlink high speed packetservices of cellular networks. Results show the benefits of coded cooperation over directtransmission in terms of increased throughput. It is shown that multiplexing gains areobserved even if the mobile station features a single antenna, provided that cell wide reuse of the relay radio resource is possible.

Performance Evaluation of Six-Sectored Configuration in Hexagonal WCDMA (UMTS) Cellular Network Layout

The objective of this master's thesis is to evaluate the optimum performance of sixsectored hexagonal layout of WCDMA (UMTS) network and analyze the performance at the optimum point. The maximum coverage and the maximum capacity are the main concern of service providers and it is always a challenging task for them to achieve economically. Because the optimum configuration of a network corresponds to a configuration which minimizes the number of sites required to provide a target service probability in the planning area which in turn reduces the deployment cost. The optimum performance means the maximum cell area and themaximum cell capacity the network can provide at the maximum antenna height satisfying the target service probability. Hexagon layout has been proven as the best layout for the cell deployment. In this thesis work, two different configurations using six-sectored sites have been considered for the performance comparison. In first configuration, each antenna is directed towards each corner of hexagon, whereas in second configurationeach antenna is directed towards each side of hexagon. The net difference in the configurations is the 30 degree rotation of antenna direction. The only indoor users in a flat and smooth semi-urban environment area have been considered for the simulation purpose where the traffic distribution is 100 Erl/km2 with 12.2 kbps speech service having maximum mobile speed of 3 km/hr. The simulation results indicate that a similar performance can be achieved in both the configurations, that is, a maximum of 947 m cellrange at antenna height of 49.5 m can be achieved when the antennas are directed towards the corner of hexagon, whereas 943.3 m cell range atantenna height of 54 m can be achieved when the antennas are directed towards the side of hexagon. However, from the interference point of view the first configuration provides better results. The simulation results also show that the network is coverage limited in both the uplink and downlink direction at the optimum point.

Ohutlevy-yrityksen mekaanisen valmistuksen tehostaminen

Diplomityön tavoitteena on tehostaa ohutlevytuotteita valmistavan yrityksen toimintaa ja parantaa tuotannon ohjattavuutta. Tuotannon tehostamisessa keskitytään minimoimaan asetusajat, pienentämään eräkokoja ja investoimaan valmistusta helpottaviin työkoneisiin tai -laitteisiin. Tuotannon ohjattavuutta kehitetään helpottamalla visuaalista seurantaa, layout-muutoksilla ja FiFo-ohjauksen käyttöönotolla. Kaikilla kehitystoimenpiteillä pyritään lyhentämään tuotannon läpimenoaikaa ja vähentämään keskeneräisen tuotannon määrää. Tavoitteena on luoda pohja Lean-valmistukselle. Kehitystoimenpiteet keskitetään useimmiten pullonkauloiksi muodostuville osastoille. Kapeikkojen avaamisessa hyödynnetään CIM-projektin mukaisesti tehtäviä investointeja. Uudella robottisärmäysyksiköllä mahdollistetaan litistäminen ja särmääminen yhdellä asetuksella. Kokoonpano-osaston sijaintia muutettiin ja osaston layoutista tehtiin linjamainen. Tuotannonohjauksen kehittämiseksi luotiin yksinkertainen kolmen askeleen kehitysmalli.

Vaiheohjatut antenniryhmät GSM-tukiasemissa

Diplomityön aiheena oli selvittää onko Suomessa GSM-tukiasemissa käytössä vaiheohjattuja antenniryhmiäja olisiko tällaisten antennien käyttöön kiinnostusta tai mitään es-teitä. Lähtökohtana tälle työlle oli ajatus GSM-tukiasema-antennista, jota voitaisiin kääntää tarpeen mukaan haluttuun suuntaan. Vaiheohjatut antenniryhmät mahdollistavat juuri tällaisen antennin keilan kääntämisen ja muokkaamisen elektronisesti, ilman kuluvia osia. Keilan muitakin ominaisuuksia voidaan säätää, kuten muotoa ja keilojen määrää. Nämä ominaisuudet mahdollistaisivat esimerkiksi ruuhkaisilla alueilla keilojen lisäämisen, jolloin alueen puhelujen välityskapasiteetti kasvaisi.Tarvittaessa voitaisiin myös keilan muotoa muuttaa. Esimerkiksi hätätilanteessasaadaan haluttu keila suunnattua tarkasti tietylle alueelle tai toiselle tukiasemalle ja näin varmistettua kuuluvuus. Myös huoltotoimenpiteet joissakin tapauksissa helpottuisivat. Etenkin vaikeakulkuisissa paikoissa sijaitsevien tukiasemien ensiapu, esimerkiksi antennin fyysisesti kääntyessä, voitaisiin hoitaa etänä kääntämällä pelkkää keilaa ja tässä tapauksessa kääntää antenni tukiaseman normaalin huollon yhteydessä. Suurimpia ongelmakohtia kyseisen tekniikan käyttöönotossa on ollut hinta, mutta muun muassa uusien valmistustekniikoiden avulla vaiheohjattujen antenniryhmien hintoja ollaan saatu pudotettua.

Typpeä sisältävien jätevesien käsittely 2-n-PRO menetelmällä

Työssä tutkittiin kaksivaiheisen typenpoistoprosessin (2-N-PRO) soveltuvuutta Joutsenon Kukkuroinmäen aluejätekeskuksen kompostointilaitoksen jätevesille pilot-kokein 12.1.- 5.4.2006. Kompostilaitoksella on jätevesien esikäsittelytarve korkeista ammoniumtyppipitoisuuksista johtuen. Pilot-laitteisto koostuu sekoitussäiliöstä, strippaustornista ja katalyyttipolttimesta. Käsiteltävän jäteveden pH nostetaan korkealle tasolle, jolloin ammoniumtyppi muuttuu ammoniakiksi. Vesi johdetaan strippaustorniin, jossa se sadetetaan tornin pohjalle. Ammoniakki erottuu sadetuksessa ilmaan, joka imetään katalyyttipolttimelle. Katalyyttinen poltin käsittelee ammoniakkia typpikaasuksi. Pilot-kokeet suoritettiin jatkuvatoimisesti. Laitteisto pystyy erottamaan jätevedestä ammoniumtyppeä ammoniakiksi ja käsittelemään ammoniakin pääosin typpikaasuksi. Lisäksi suoritettiin panoskoe, jonka tulokset tukevat jatkuvatoimisesta käytöstä saatuja tuloksia.

Modelado circuital de diferentes configuraciones de antenas microstrip

L’objectiu del projecte es facilitar el disseny i la modificació d’antenes microstrip utilitzant models circuitals. En el document s’exposa conjuntament la teoria de vàries configuracions d’antenes microstrip dispersa en varis documents i les equacions més rellevants per l’anàlisi dels fenòmens que es produeixen en cada model d’antena amb l’objectiu de realitzar un estudi detallat de les tendències dels components de cada configuració. L’estudi de les tendències es realitza per obtenir una relació entre els paràmetres físics i els components dels models circuitals proposats per a cada configuració d’antena microstrip. Utilitzant la teoria exposada en el document i l’estudi realitzat es comprova que és possible facilitar i realitzar modificacions en el disseny d’antenes microstrip mitjançant els models circuitals proposats.