Improved handling and preservation of freshwater giant prawn, Macrobrachium rosenbergii for producing safe and wholesome products

Studies were undertaken to evaluate the quality changes in freshwater giant prawn, Macrobrachium rosenbergii during various storage conditions of handling and preservation and producing safe and quality products. The samples kept in ice immediately after catch with head-on and head-less condition were found to be acceptable for 6 days and 7 days, respectively. Delaying of icing considerably shortened the shelf-life. The pH value increased from 6.36 to 8.0 after 10 days in ice. The initial average TVB-N value of sample increased from below 10 mg/100 g to 25 mg/100 g with the lapse of storage period. The Ca++ ATPase activity in presence of 0.1M KCl slightly decreased at the end of 10 days of ice storage. Immediately after harvest, initial aerobic plate count (APC) was 2.88x10^6 CFU/g which gradually increased to 1.12x10^8 CFU/g after 6 days in ice storage and showed early signs of spoilage. Initial bacterial genera in the prawn iced at 0 hours were comprised of Coryneform (22.21 %), Bacillus (7.40%), Micrococcus (11.11 %), Achromobacter (48.14%), Flavobacterium/Cytophaga (7.40%), Pseudomonas (3.70%) and Aeromonas (3.70%). During ice storage Coryneforms and Bacillus were always dominating along with less prominent ones - Micrococcus, Achromobacter and Flavobacterium. Studies were conducted on the stability of myofibrillar protein of M. rosenbergii under different storage and pH conditions. The influence of a wide range of pH on the remaining Ca++ ATPase activity of M. rosenbergii muscle myofibrils after storage at -20°C for 2 days, at 0°C for 2 days and at 35°C for 30 minutes demonstrated that ATPase activities were lower in acidic and alkaline pH regions and the activity remained relatively high. Mg++ ATPase activities both in presence and absence of Ca++ remained high at neutral pH compared to those of acidic and alkaline region. The solubility of myofibrillar protein decreased gradually both in acidic and alkaline pH regions. The study also examined the bacteriological quality of freshly harvested M. rosenbergii, pond sediment and pond water from four commercial freshwater prawn farms at Fulpur and Tarakanda upazilas in the district of Mymensingh. The study included aerobic plate count (APC), total coliform count, detection, isolation and identification of suspected public health hazard bacteria and their seasonal variation, salt tolerance test, antibiotic sensitivity test of the isolates and washing effect of chlorinated water on the bacterial load in the prawn samples. APC in sediment soil and water of the farm and gill and hepatopancreas of freshly harvested prawns varied considerably among the farms and between summer and winter season. The range of coliform count in water, gill and hepatopancreas ranged between 6 - 2.8x10^2 CFU/ml, 1.2x10^2 - 3.32x10^2 CFU/g and 1.43x10^2 - 3.89 x10^3 CFU/g, respectively. No coliform was detected in pond sediment sample. Suspected health hazard bacteria isolated and identified from pond sediment, water, gill and hepatopancreas included Streptococcus, Bacillus, Escherichia coli, Klebsialla, Salmonella, Staphylococcus, Pseudomonas and Aeromonas. Bacillus, Salmonella and Staphyloccus [sic], and were found to be highly salt tolerant and capable of growing at 10% NaCl. The antibiotic discs with different concentration of antibiotics were used for the sensitivity test. The organisms were found to be most sensitive against Tetracyclin and Gentamycin.

Investigations on wooden floating materials: the loss of buoyancy under continuous immersion in water and the rate of its redemption by drying

A wooden fishing float under immersion in water for long periods is liable to absorb water, the quantity of water absorbed possibly being dependent upon the physical factors like the specific gravity and the inherent property of the material, the time of soaking and the pressure acting on it. Consequently a wooden float is likely to become heavy and loss its original buoyancy. However, when the float is removed from water and dried, the lost buoyancy is regained on complete drying. The present paper is an attempt to elucidate these two important characteristics of some of the chief wooden floating materials used on the West Coast of India.

On the comparative efficiency of trawls made of cotton, polyethylene and combination of both the materials

The merits and demerits of cotton, polyethylene and combination of the two materials ascertained on the basis of cost, wear and tear, maintenance, total catch and qualitative analysis of the catch are discussed by making comparative fishing experiments with the three trawl gears made of these materials. The study can be concluded with a suggestion for switching over to polyethylene twisted monofilaments for better, in case of bottom trawls without in any way adversely affecting the catch of shrimps and at the same time for enhanced fish catch. Even though the combination net is found to be equal in efficiency as the polyethylene net this idea cannot be conveniently adopted from the point of view of economy.

A wider choice of construction materials for the modern fishing boats

An account of fishing vessel construction materials is given, with information on essential features, and a material account. Materials discussed in detail are steel, wood, aluminium, glass reinforced plastic, and ferro-cement.

Load-displacement behavior during sharp indentation of viscous-elastic-plastic materials

A constitutive equation is developed for geometrically-similar sharp indentation of a material capable of elastic, viscous, and plastic deformation. The equation is based on a series of elements consisting of a quadratic (reversible) spring, a quadratic (time-dependent, reversible) dashpot, and a quadratic (time-independent, irreversible) slider-essentially modifying a model for an elastic-perfectly plastic material by incorporating a creeping component. Load-displacement solutions to the constitutive equation are obtained for load-controlled indentation during constant loading-rate testing. A characteristic of the responses is the appearance of a forward-displacing "nose" during unloading of load-controlled systems (e.g., magnetic-coil-driven "nanoindentation" systems). Even in the absence of this nose, and the associated initial negative unloading tangent, load-displacement traces (and hence inferred modulus and hardness values) are significantly perturbed on the addition of the viscous component. The viscous-elastic-plastic (VEP) model shows promise for obtaining material properties (elastic modulus, hardness, time-dependence) of time-dependent materials during indentation experiments.

Selection of materials for marine instruments

The paper describes the selection of materials for the reliable operation of oceanographic instruments. For selecting the material, raft immersion tests were carried out for one year. Results of the tests are presented. Comparisons between metals were discussed.