Estudo da produção eletroquímica de espécies de cloro ativo para tratamento de efluentes sintéticos

The treatment of wastewater is essential to human health. One of the most important steps is the disinfection treatment which uses chlorine to eliminate bacteria as required by environmental agencies. However, the identification of potentially toxic byproducts generated by this method, such as trihalomethanes, has stimulated the development of new alternative disinfection technologies. Among them, heterogeneous photocatalysis, TiO2 photocatalysis and electrochemical disinfection are considered suitable alternatives to the chlorination method. Thus, the present dissertation analyzes the evolution of active chlorine species in a synthetic NaCl solution and it is tested to treat a synthetic solution of the dye Reactive Blue 19 using boron-doped diamond (BDD) and ruthenium oxide (Ti/Ru0.3Ti0.7O2) as anodes. The indirect electrochemical process was discussed in terms of mineralization of the total organic load and percentage of color removal in order to evaluate the applicability of electrochemical technology. Electrochemical experiments were carried out with different current densities (25, 50 and 75 mA.cm-2) during 120 minutes. On the other hand, other important parameter in this study was the influence of the proportion sp3/sp2 on BDD anode on the performance of the evolution of active chlorine species which was investigated by electrolytic techniques (linear polarization), with the intention of determining the related training oxidizing species and consumption energy to chemical or electrochemical reactions. From the results, it can be noted that the BDD electrode showed better efficiency throughout the electrochemical process.

Estudo da produção eletroquímica de espécies de cloro ativo para tratamento de efluentes sintéticos

The treatment of wastewater is essential to human health. One of the most important steps is the disinfection treatment which uses chlorine to eliminate bacteria as required by environmental agencies. However, the identification of potentially toxic byproducts generated by this method, such as trihalomethanes, has stimulated the development of new alternative disinfection technologies. Among them, heterogeneous photocatalysis, TiO2 photocatalysis and electrochemical disinfection are considered suitable alternatives to the chlorination method. Thus, the present dissertation analyzes the evolution of active chlorine species in a synthetic NaCl solution and it is tested to treat a synthetic solution of the dye Reactive Blue 19 using boron-doped diamond (BDD) and ruthenium oxide (Ti/Ru0.3Ti0.7O2) as anodes. The indirect electrochemical process was discussed in terms of mineralization of the total organic load and percentage of color removal in order to evaluate the applicability of electrochemical technology. Electrochemical experiments were carried out with different current densities (25, 50 and 75 mA.cm-2) during 120 minutes. On the other hand, other important parameter in this study was the influence of the proportion sp3/sp2 on BDD anode on the performance of the evolution of active chlorine species which was investigated by electrolytic techniques (linear polarization), with the intention of determining the related training oxidizing species and consumption energy to chemical or electrochemical reactions. From the results, it can be noted that the BDD electrode showed better efficiency throughout the electrochemical process.

Controle ativo de vibração em estruturas inteligentes utilizando um controlador por modos deslizantes com compensação difusa

Smart structures and systems have the main purpose to mimic living organisms, which are essentially characterized by an autoregulatory behavior. Therefore, this kind of structure has adaptive characteristics with stimulus-response mechanisms. The term adaptive structure has been used to identify structural systems that are capable of changing their geometry or physical properties with the purpose of performing a specific task. In this work, a sliding mode controller with fuzzy inference is applied for active vibration control in an SMA two-bar truss. In order to obtain a simpler controller, a polynomial model is used in the control law, while a more sophisticated version, which presents close agreement with experimental data, is applied to describe the SMA behavior of the structural elements. This system has a rich dynamic response and can easily reach a chaotic behavior even at moderate loads and frequencies. Therefore, this approach has the advantage of not only obtaining a simpler control law, but also allows its robustness be evidenced. Numerical simulations are carried out in order to demonstrate the control system performance.

Controle ativo de vibração em estruturas inteligentes utilizando um controlador por modos deslizantes com compensação difusa

Smart structures and systems have the main purpose to mimic living organisms, which are essentially characterized by an autoregulatory behavior. Therefore, this kind of structure has adaptive characteristics with stimulus-response mechanisms. The term adaptive structure has been used to identify structural systems that are capable of changing their geometry or physical properties with the purpose of performing a specific task. In this work, a sliding mode controller with fuzzy inference is applied for active vibration control in an SMA two-bar truss. In order to obtain a simpler controller, a polynomial model is used in the control law, while a more sophisticated version, which presents close agreement with experimental data, is applied to describe the SMA behavior of the structural elements. This system has a rich dynamic response and can easily reach a chaotic behavior even at moderate loads and frequencies. Therefore, this approach has the advantage of not only obtaining a simpler control law, but also allows its robustness be evidenced. Numerical simulations are carried out in order to demonstrate the control system performance.

Degradação de paracetamol empregando tecnologia oxidativa avançada baseada em fotocatálise heterogênea usando irradiação artificial e solar

In this work, the oxidation and mineralization of paracetamol, based in an advanced oxidative process promoted by heterogeneous photocatalysis, was evaluated. The action of two photocatalysts (titanium dioxide, and a composite based on the association between titanium dioxide and zinc phthalocyanine dye) was studied. First of all, experiments in laboratory scale were performed using as radiation font a 400 W high pressure mercury lamp. The mineralization of paracetamol, promoted by both photocatalysts, was evaluated working with 4L of solution containing 10 mg L-1 of paracetamol and 100 mg L-1 of photocatalyst. To find the best experimental conditions, the influence of hydrogen peroxide concentration and pH was evaluated for the reactions. The best results for the reactions in laboratory scale was obtained using 33,00 mg L-1 of hydrogen peroxide in natural pH (6,80). Under these conditions, 100% oxidation was reached in just 40 minutes of reaction using TiO2 P25, while the mineralization was 78%. Using the composite, the mineralization was 63% in 2 hours of reaction and a oxidation of almost 100% was reached after 60 minutes. A CPC reactor (compound parabolic concentrator) was employed in the expanded work scale, using the sun as irradiation source. In this case the experiments were performed using 50 L of aqueous solution containing 10 mg L-1 of paracetamol and 100 mg L-1 of photocatalyst. The assays were done at pH 3,00 and natural pH (6,80). The used concentration of hydrogen peroxide was 33,00 mg L-1, adopted after laboratory scale studies. The reaction at pH 3,00 shows to be more advantageous, since under natural pH (6,80), the use of deionized water was necessary to prepare the solutions, probably because the deleterious action of carbonate ions, known hydroxyl radical scavengers. Using solar irradiation, the reaction mediated by the composite was more efficient when compared with the assays under laboratory scale since the composite presents the advantage of promoting a better use of visible radiation. Under these conditions, the mineralization increased from 40% to 56% under pH 3,00. At natural pH the oxidation occurred more slowly and the mineralization decreased from 56% to 50%. Thus, the use of pH 3,00 will be more interesting in real scale applications, even if it is necessary the pH correction before the discard of the treated effluent to the environment.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Caracterização mecânica da liga AlSi10Mg obtida por SLM para aplicação em componentes automóveis

Este projeto visa efetuar a caracterização mecânica da liga AlSi10Mg obtida por SLM (Fundição de Metal por Laser) para aplicação em componentes automóveis. Ao longo deste projeto é efetuada uma pesquisa bibliográfica das tecnologias de fabrico rápido mais frequentemente aplicadas ao processamento de alumínios, abordando de forma específica a tecnologia SLM, bem como a influência dos seus parâmetros no processamento de ligas de alumínio. Será levado a cabo um estudo comparativo da liga AlSi10Mg fabricada por fundição em molde permanente com a obtida por SLM, analisando-se a microestrutura das ligas, bem como as suas propriedades mecânicas, através da realização de ensaios de dureza, tração, análise dinâmico-mecânica e fadiga. Deste modo será possível perceber as diferenças entre o comportamento mecânico da liga obtida por SLM e a liga obtida pelo método convencional. Em resultado do estudo realizado, observou-se que a liga AlSi10Mg obtida por SLM apresenta uma microestrutura muito mais fina do que a liga fabricada por fundição em molde permanente, o que lhe permite ter um comportamento mecânico superior na maioria dos ensaios mecânicos realizados. Assim, é possível aplicar a tecnologia SLM ao fabrico de componentes em alumínio no sector automóvel, visto ser possível obter propriedades mecânicas superiores ou equivalentes aos componentes fabricados pelos processos de fabrico convencionais.

Development and Application of a Multi-dimensional Strategy for Measuring Fidelity of Implementation of a Districtwide Intervention

This symposium describes a multi-dimensional strategy to examine fidelity of implementation in an authentic school district context. An existing large-district peer mentoring program provides an example. The presentation will address development of a logic model to articulate a theory of change; collaborative creation of a data set aligned with essential concepts and research questions; identification of independent, dependent, and covariate variables; issues related to use of big data that include conditioning and transformation of data prior to analysis; operationalization of a strategy to capture fidelity of implementation data from all stakeholders; and ways in which fidelity indicators might be used.

Associações de jogos tradicionais no Brasil

Esse estudo tem como tema as Associaçoes Jogos Tradicionais, entendidas como espaço e tempo resultantes da reuniao de pessoas ou de grupos sociais em torno de um ou mais jogos tradicionais. Compreendemos essas manifestaçoes como parte da cultura corporal, criadas e recriadas pelos seres humanos no processo histórico, transmitidas de geraçao em geraçao e presentes em determinada cultura. Pesquisas anteriores, realizadas pelo Grupo de Pesquisa em Lazer e Formaçao de Professores (GPELF), identificaram que existe uma diversidade de Associaçoes de Jogos Tradicionais no Brasil. Nesse sentido, o objetivo desse estudo é compreender estes espaços de açoes onde sao desenvolvidos os jogos tradicionais no território brasileiro, suas características, abrangência, sujeitos envolvidos, jogos praticados e açoes desenvolvidas. Trata-se de uma pesquisa em andamento. Como procedimentos metodológicos, utilizamos pesquisa documental e entrevistas semiestruturadas. A partir das primeiras inserçoes no que tange à pesquisa documental, identificamos 98 Associaçoes no contexto brasileiro, entre elas estao: 15 federaçoes, 38 associaçoes, 22 clubes, 5 centros comunitários, 4 confederaçoes, , 4 sociedades, 3 ligas, e 7 outros. Constamos que dentre seus principais objetivos, estao a preservaçao de costumes e tradiçoes, a promoçao de cultura local e a defesa do patrimônio histórico

Associações de jogos tradicionais no Brasil

Esse estudo tem como tema as Associaçoes Jogos Tradicionais, entendidas como espaço e tempo resultantes da reuniao de pessoas ou de grupos sociais em torno de um ou mais jogos tradicionais. Compreendemos essas manifestaçoes como parte da cultura corporal, criadas e recriadas pelos seres humanos no processo histórico, transmitidas de geraçao em geraçao e presentes em determinada cultura. Pesquisas anteriores, realizadas pelo Grupo de Pesquisa em Lazer e Formaçao de Professores (GPELF), identificaram que existe uma diversidade de Associaçoes de Jogos Tradicionais no Brasil. Nesse sentido, o objetivo desse estudo é compreender estes espaços de açoes onde sao desenvolvidos os jogos tradicionais no território brasileiro, suas características, abrangência, sujeitos envolvidos, jogos praticados e açoes desenvolvidas. Trata-se de uma pesquisa em andamento. Como procedimentos metodológicos, utilizamos pesquisa documental e entrevistas semiestruturadas. A partir das primeiras inserçoes no que tange à pesquisa documental, identificamos 98 Associaçoes no contexto brasileiro, entre elas estao: 15 federaçoes, 38 associaçoes, 22 clubes, 5 centros comunitários, 4 confederaçoes, , 4 sociedades, 3 ligas, e 7 outros. Constamos que dentre seus principais objetivos, estao a preservaçao de costumes e tradiçoes, a promoçao de cultura local e a defesa do patrimônio histórico

Civic Humanism and the Classical Tradition in the Early Republic of Chile

The first decades of the 19th century constituted a period of profound change for Chile, the principal results of which were to be seen in the consolidation of the process of independence from Spanish dominion in 1818. The consequences were not limited to a revolution of military and political nature; they also included a renovation of the cultural panorama -at least among the educated patriots who made an effort to distance themselves ideologically from the Monarchy-, with the implicit challenge of establishing a new order for Chile, based on legitimate and universally recognizable foundations. The inspirational framework for these efforts is usually associated with other revolutionary examples -France and the United States- that preceded the emancipation processes in Spanish America, as well as with the discourses of illustrated liberalism. As we will attempt to demonstrate in this study, a new reading of the texts written by the Creoles that lead the Chilean independence process may, nonetheless, also reveal the relevance of the classical tradition as a model for the configuration and legitimization of the first Republican projects that especially admired the ideals of Republicanism.

Associações de jogos tradicionais no Brasil

Esse estudo tem como tema as Associaçoes Jogos Tradicionais, entendidas como espaço e tempo resultantes da reuniao de pessoas ou de grupos sociais em torno de um ou mais jogos tradicionais. Compreendemos essas manifestaçoes como parte da cultura corporal, criadas e recriadas pelos seres humanos no processo histórico, transmitidas de geraçao em geraçao e presentes em determinada cultura. Pesquisas anteriores, realizadas pelo Grupo de Pesquisa em Lazer e Formaçao de Professores (GPELF), identificaram que existe uma diversidade de Associaçoes de Jogos Tradicionais no Brasil. Nesse sentido, o objetivo desse estudo é compreender estes espaços de açoes onde sao desenvolvidos os jogos tradicionais no território brasileiro, suas características, abrangência, sujeitos envolvidos, jogos praticados e açoes desenvolvidas. Trata-se de uma pesquisa em andamento. Como procedimentos metodológicos, utilizamos pesquisa documental e entrevistas semiestruturadas. A partir das primeiras inserçoes no que tange à pesquisa documental, identificamos 98 Associaçoes no contexto brasileiro, entre elas estao: 15 federaçoes, 38 associaçoes, 22 clubes, 5 centros comunitários, 4 confederaçoes, , 4 sociedades, 3 ligas, e 7 outros. Constamos que dentre seus principais objetivos, estao a preservaçao de costumes e tradiçoes, a promoçao de cultura local e a defesa do patrimônio histórico

Cirurgia de fraturas ósseas na osteoporose: Fraturas da coluna vertebral

As fraturas que ocorrem no osso osteoporótico são por definição estrita fraturas patológicas. Podem estar relacionadas com quedas da própria altura ou de traumatismos de baixa energia cinética e envolvem habitualmente a anca, o punho, a coluna vertebral e o ombro. As fraturas osteoporóticas a que se associa a sarcopenia, representam um sério problema de saúde pública em todo o mundo, com uma proporção epidémica e um impacto devastador na morbilidade e mortalidade dos pacientes, assim como nos custos socioeconómicos. Apesar dos avanços registados na prevenção e no tratamento farmacológico da osteoporose bem como no tratamento cirúrgico das fraturas ósseas, continuam a ser desenvolvidos novos biomateriais metálicos e substitutos sintéticos do osso com a intenção de se conseguir alcançar melhores resultados clínicos. Dentro deste contexto incluem-se os cimentos hidráulicos, os parafusos expansivos, os parafusos dinâmicos, as malhas metálicas de titânio, as placas bloqueadas, entre outros, em conjugação com técnicas minimamente invasivas e com diferentes estratégias cirúrgicas. O objetivo central deste trabalho assenta nas modalidades cirúrgicas mais usadas para o tratamento das fraturas em osso osteoporótico, com especial destaque para as fraturas da coluna vertebral.

Desenvolvimento de um cerâmico Al2O3/TI(C,N) para uso em maquinação

O principal objetivo deste trabalho é preparar um cermeto do tipo Al2O3/Ti(C,N) com propriedades mecânicas adequadas à sua utilização na maquinação de materiais do tipo DIN ISO 513:K01-K10 e ISO H01-H10. De forma a incrementar a sinterabilidade do cermeto investigou-se o efeito da adição de dopantes metálicos, nomeadamente alumínio metálico (Al) e hidreto de titânio (TiH2) e o efeito da substituição da moagem convencional por moagem de alta energia. As variáveis das etapas principais de processamento, i.e., da moagem, prensagem e sinterização, foram selecionadas com trabalho realizado quer na Universidade de Aveiro quer na empresa Palbit. Foram preparadas três composições do cermeto Al2O3/Ti(C,N) com adições de 5%TiH2, 1%Al e 5%TiH21%Al através da moagem de alta energia. Os parâmetros de moagem, i.e. a velocidade de rotação, o rácio bolas/pó e o tempo de moagem foram otimizados para os seguintes valores: 350 rpm, 10:1 e 5 h, respetivamente. A utilização da moagem de alta energia permitiu uma redução do tamanho de partícula dos pós até aproximadamente 100 nm e a obtenção de uma boa uniformidade da distribuição das fases (Al2O3+Ti(C,N)). A etapa de conformação foi efetuada por prensagem uniaxial seguida de prensagem isostática. A avaliação da reatividade dos cermetos através de dilatometria em atmosfera de vácuo revelou que a densificação é maioritariamente realizada em estado sólido. A adição de apenas 1%Al é a menos efetiva para a densificação. Os cermetos foram sinterizados através de sinterização convencional em forno de vazio a 1650ºC e prensagem a quente (1650ºC com uma pressão uniaxial de 25 MPa). Os valores de densificação obtidos, aproximadamente 80% e 100%, respetivamente, indicam que a aplicação de pressão durante a sinterização é efetiva para atingir densificações elevadas nos compactos, compatíveis com as suas aplicações tecnológicas. As propriedades mecânicas de dureza e de tenacidade avaliadas nos três cermetos apresentaram valores aproximados de 1800-1900 HV50 para a dureza e entre 5.4 e 7.7 MPa.m1/2 para a tenacidade à fratura.