Estudo da resistência e mecanismos de dano em juntas adesivas entre materiais compósitos com defeitos de adesão

A necessidade de utilizar métodos de ligação entre componentes de forma mais rápida, eficaz e com melhores resultados tem causado a crescente utilização das juntas adesivas, em detrimento dos métodos tradicionais de ligação. A utilização das juntas adesivas tem vindo a aumentar em diversas aplicações industriais por estas apresentarem vantagens, das quais se destacam a redução de peso, redução de concentrações de tensões e facilidade de fabrico. No entanto, uma das limitações das juntas adesivas é a dificuldade em prever a resistência da junta após fabrico e durante a sua vida útil devido à presença de defeitos no adesivo. Os defeitos são normalmente gerados pela preparação inadequada das juntas ou degradação do adesivo devido ao ambiente (por exemplo, humidade), reduzindo a qualidade da ligação e influenciando a resistência da junta. Neste trabalho é apresentado um estudo experimental e numérico de juntas de sobreposição simples (JSS) com a inclusão de defeitos centrados na camada de adesivo para comprimentos de sobreposição (LO) diferentes. Os adesivos utilizados foram o Araldite® AV138, apresentado como sendo frágil, e o adesivo Sikaforce® 7752, intitulado como adesivo dúctil. A parte experimental consistiu no ensaio à tração das diferentes JSS permitindo a obtenção das curvas força-deslocamento (P-δ). A análise numérica por modelos de dano coesivo (MDC) foi realizada para analisar as tensões de arrancamento ((σy) e as tensões de corte (τxy) na camada adesiva, para estudar a variável de dano do MDC durante o processo de rotura e para avaliar a capacidade dos MDC na previsão da resistência da junta. Constatou-se um efeito significativo dos defeitos de diferentes dimensões na resistência das juntas, que também depende do tipo de adesivo utilizado e do valor de LO. Os modelos numéricos permitiram a descrição detalhada do comportamento das juntas e previsão de resistência, embora para o adesivo dúctil a utilização de uma lei coesiva triangular tenha provocado alguma discrepância relativamente aos resultados experimentais.

Comparação de técnicas analíticas e numéricas para previsão de resistência de juntas adesivas de sobreposição simples

As juntas adesivas têm vindo a ser usadas em diversas áreas e contam com inúmeras aplicações práticas. Devido ao fácil e rápido fabrico, as juntas de sobreposição simples (JSS) são um tipo de configuração bastante comum. O aumento da resistência, a redução de peso e a resistência à corrosão são algumas das vantagens que este tipo de junta oferece relativamente aos processos de ligação tradicionais. Contudo, a concentração de tensões nas extremidades do comprimento da ligação é uma das principais desvantagens. Existem poucas técnicas de dimensionamento precisas para a diversidade de ligações que podem ser encontradas em situações reais, o que constitui um obstáculo à utilização de juntas adesivas em aplicações estruturais. O presente trabalho visa comparar diferentes métodos analíticos e numéricos na previsão da resistência de JSS com diferentes comprimentos de sobreposição (LO). O objectivo fundamental é avaliar qual o melhor método para prever a resistência das JSS. Foram produzidas juntas adesivas entre substratos de alumínio utilizando um adesivo époxido frágil (Araldite® AV138), um adesivo epóxido moderadamente dúctil (Araldite® 2015), e um adesivo poliuretano dúctil (SikaForce® 7888). Consideraram-se diferentes métodos analíticos e dois métodos numéricos: os Modelos de Dano Coesivo (MDC) e o Método de Elementos Finitos Extendido (MEFE), permitindo a análise comparativa. O estudo possibilitou uma percepção crítica das capacidades de cada método consoante as características do adesivo utilizado. Os métodos analíticos funcionam apenas relativamente bem em condições muito específicas. A análise por MDC com lei triangular revelou ser um método bastante preciso, com excepção de adesivos que sejam bastante dúcteis. Por outro lado, a análise por MEFE demonstrou ser uma técnica pouco adequada, especialmente para o crescimento de dano em modo misto.

Tempos de espera cirúrgicos: situação em Portugal e determinantes

RESUMO - Objectivos Um dos problemas mais comuns nos sistemas de saúde e particularmente naqueles que têm uma estrutura predominantemente pública são os elevados Tempos Espera (TE) para cirurgia. Este projecto tem como principal objectivo identificar a importância relativa em Portugal das determinantes do TE cirúrgico. Metodologia Para clarificar essa importância, aplicou-se um questionário desenvolvido pelo Fraser Institute, utilizado para a análise anual dos TE no Canadá, recorrendo a um painel de peritos e através da realização da técnica Delphi, procurou-se consensualizar quais as determinantes das Listas Espera (LE), mais importantes. Para ilustrar a diversidade de perspectivas, recorreu-se também à análise de trabalhos realizados por inúmeras organizações, onde pudemos observar e recolher distintas abordagens, políticas e técnicas da questão das LE em países com diferentes tipos de sistemas de saúde. Resultados Os resultados obtidos revelam que os peritos consideraram a disponibilidade de tempo no Bloco Operatório (BO) e a de anestesiologistas, como as determinantes com maior impacto no aumento das LE. Conclusões Dos dados recebidos relativos ao Sistema Integrado Gestão Inscritos Cirurgia (SIGIC), bem como dos retirados de relatórios oficiais, concluímos que as LE cirúrgicas tiveram evolução positiva, nomeadamente na redução da mediana do TE da Lista Inscritos Cirurgia (LIC) (meses), no entanto, os objectivos dos Tempos Máximos Resposta Garantidos (TMRG) não estão a ser cumpridos. A análise das diferentes iniciativas e estratégias políticas para combater as LE, permitiu-nos sugerir caminhos a explorar, tendo como objectivo minorar o problema das LE: cuidados integrados, optimização da eficiência na utilização da capacidade instalada e maior aposta na cirurgia de ambulatório.

Internamentos hospitalares da população com mais de 65 anos em Portugal – Análise Descritiva

RESUMO - As mudanças na saúde são cada vez mais rápidas e os serviços de saúde têm cada vez mais dificuldade em dar resposta aos problemas de saúde dos portugueses. Responsáveis por grande parte da despesa em saúde, os idosos são a população que mais utiliza os serviços de saúde e as respetivas unidades hospitalares e serviços de urgência. Estes têm estadias mais prolongadas e consomem mais recursos durante essas permanências nas instituições de saúde. Sabendo isto revelou-se oportuno encontrar as principais causas de internamento hospitalar, os principais diagnósticos secundários, demoras médias e a sua relação com as principais causas de morte na população portuguesa com mais de 65 anos no período de 2003-2012. Para tal, optou-se por uma análise descritiva de 3375817 episódios de internamento referentes a dez anos. Daqui retirou-se que os diagnósticos principais mais frequentes para todos os anos e todas as faixas etárias são o acidente vascular cerebral isquémico e a pneumonia, sendo que o primeiro é o mais frequente até 2006, passando depois a ser a pneumonia o mais frequente. A demora média é maior quanto mais diagnósticos secundários associados houver e aumenta com a idade. Os diagnósticos secundários mais frequentes são a hipertensão essencial e a diabetes mellitus. Estes dados são relevantes para o conhecimento da saúde em Portugal, podendo-se alterar e uniformizar e melhorar práticas hospitalares e com isso progredir na qualidade dos tratamentos e aumentar a qualidade de vida com hipótese de diminuição da demora média.

Reconfigurable photonic logic architecture

The amorphous silicon photo-sensor studied in this thesis, is a double pin structure (p(a-SiC:H)-i’(a-SiC:H)-n(a-SiC:H)-p(a-SiC:H)-i(a-Si:H)-n(a-Si:H)) sandwiched between two transparent contacts deposited over transparent glass thus with the possibility of illumination on both sides, responding to wave-lengths from the ultra-violet, visible to the near infrared range. The frontal il-lumination surface, glass side, is used for light signal inputs. Both surfaces are used for optical bias, which changes the dynamic characteristics of the photo-sensor resulting in different outputs for the same input. Experimental studies were made with the photo-sensor to evaluate its applicability in multiplexing and demultiplexing several data communication channels. The digital light sig-nal was defined to implement simple logical operations like the NOT, AND, OR, and complex like the XOR, MAJ, full-adder and memory effect. A pro-grammable pattern emission system was built and also those for the validation and recovery of the obtained signals. This photo-sensor has applications in op-tical communications with several wavelengths, as a wavelength detector and to execute directly logical operations over digital light input signals.

Fatigue life assessment of endodontic instruments subjected to multi planar curvature

This present study aimed to investigate the fatigue life of unused (new) endodontic instruments made of NiTi with control memory by Coltene™ and subjected to the multi curvature of a mandibular first molar root canal. Additionally, the instrument‟s structural behaviour was analysed through non-linear finite element analysis (FEA). The fatigue life of twelve Hyflex™ CM files was assessed while were forced to adopt a stance with multiple radius of curvature, similar to the ones usually found in a mandibular first molar root canal; nine of them were subjected to Pecking motion, a relative movement of axial type. To achieve this, it was designed an experimental setup with the aim of timing the instruments until fracture while worked inside a stainless steel mandibular first molar model with relative axial motion to simulate the pecking motion. Additionally, the model‟s root canal multi-curvature was confirmed by radiography. The non-linear finite element analysis was conducted using the computer aided design software package SolidWorks™ Simulation, in order to define the imposed displacement required by the FEA, it was necessary to model an endodontic instrument with simplified geometry using SolidWorks™ and subsequently analyse the geometry of the root canal CAD model. The experimental results shown that the instruments subjected to pecking motion displayed higher fatigue life values and higher lengths of fractured tips than those with only rotational relative movement. The finite element non-linear analyses shown, for identical conditions, maximum values for the first principal stress lower than the yield strength of the material and those were located in similar positions to the instrument‟s fracture location determined by the experimental testing results.

Heritability, determinants and reference values of renal length: a family-based population study.

OBJECTIVES: In this population-based study, reference values were generated for renal length, and the heritability and factors associated with kidney length were assessed. METHODS: Anthropometric parameters and renal ultrasound measurements were assessed in randomly selected nuclear families of European ancestry (Switzerland). The adjusted narrow sense heritability of kidney size parameters was estimated by maximum likelihood assuming multivariate normality after power transformation. Gender-specific reference centiles were generated for renal length according to body height in the subset of non-diabetic non-obese participants with normal renal function. RESULTS: We included 374 men and 419 women (mean ± SD, age 47 ± 18 and 48 ± 17 years, BMI 26.2 ± 4 and 24.5 ± 5 kg/m(2), respectively) from 205 families. Renal length was 11.4 ± 0.8 cm in men and 10.7 ± 0.8 cm in women; there was no difference between right and left renal length. Body height, weight and estimated glomerular filtration rate (eGFR) were positively associated with renal length, kidney function negatively, age quadratically, whereas gender and hypertension were not. The adjusted heritability estimates of renal length and volume were 47.3 ± 8.5 % and 45.5 ± 8.8 %, respectively (P < 0.001). CONCLUSION: The significant heritability of renal length and volume highlights the familial aggregation of this trait, independently of age and body size. Population-based references for renal length provide a useful guide for clinicians. KEY POINTS: • Renal length and volume are heritable traits, independent of age and size. • Based on a European population, gender-specific reference values/percentiles are provided for renal length. • Renal length correlates positively with body length and weight. • There was no difference between right and left renal lengths in this study. • This negates general teaching that the left kidney is larger and longer.

Distal dendrites of frog motor neurons: a computer-aided electron microscopic study of cobalt-filled cells.

With the aid of the cobalt labelling technique, frog spinal cord motor neuron dendrites of the subpial dendritic plexus have been identified in serial electron micrographs. Computer reconstructions of various lengths (2.5-9.8 micron) of dendritic segments showed the contours of these dendrites to be highly irregular, and to present many thorn-like projections 0.4-1.8 micron long. Number, size and distribution of synaptic contacts were also determined. Almost half of the synapses occurred at the origins of the thorns and these synapses had the largest contact areas. Only 8 out of 54 synapses analysed were found on thorns and these were the smallest. For the total length of reconstructed dendrites there was, on average, one synapse per 1.2 micron, while 4.4% of the total dendritic surface was covered with synaptic contacts. The functional significance of these distal dendrites and their capacity to influence the soma membrane potential is discussed.

Diagnostic yield of short-term video-EEG monitoring for epilepsy and PNESs: a European assessment.

INTRODUCTION: Although long-term video-EEG monitoring (LVEM) is routinely used to investigate paroxysmal events, short-term video-EEG monitoring (SVEM) lasting <24 h is increasingly recognized as a cost-effective tool. Since, however, relatively few studies addressed the yield of SVEM among different diagnostic groups, we undertook the present study to investigate this aspect. METHODS: We retrospectively analyzed 226 consecutive SVEM recordings over 6 years. All patients were referred because routine EEGs were inconclusive. Patients were classified into 3 suspected diagnostic groups: (1) group with epileptic seizures, (2) group with psychogenic nonepileptic seizures (PNESs), and (3) group with other or undetermined diagnoses. We assessed recording lengths, interictal epileptiform discharges, epileptic seizures, PNESs, and the definitive diagnoses obtained after SVEM. RESULTS: The mean age was 34 (±18.7) years, and the median recording length was 18.6 h. Among the 226 patients, 127 referred for suspected epilepsy - 73 had a diagnosis of epilepsy, none had a diagnosis of PNESs, and 54 had other or undetermined diagnoses post-SVEM. Of the 24 patients with pre-SVEM suspected PNESs, 1 had epilepsy, 12 had PNESs, and 11 had other or undetermined diagnoses. Of the 75 patients with other diagnoses pre-SVEM, 17 had epilepsy, 11 had PNESs, and 47 had other or undetermined diagnoses. After SVEM, 15 patients had definite diagnoses other than epilepsy or PNESs, while in 96 patients, diagnosis remained unclear. Overall, a definitive diagnosis could be reached in 129/226 (57%) patients. CONCLUSIONS: This study demonstrates that in nearly 3/5 patients without a definitive diagnosis after routine EEG, SVEM allowed us to reach a diagnosis. This procedure should be encouraged in this setting, given its time-effectiveness compared with LVEM.

Costos metabólicos de Engraulis ringens y Sardinops sagax en relación al peso, temperatura y el nivel de actividad

El metabolismo estándar de la anchoveta es más alto que el de la sardina; en .las larvas por un factor promedio de 2.3 y por 2.1 en juveniles y adultos en el rango de temperaturas de 14-20ºC. Lo opuesto sucede en el metabolismo activo: para una velocidad de natación de un cuerpo por segundo( =metabolismo de rutina), la anchoveta adulta con un peso mayor de 20 g a 20ºC y mayor de 50 g a 14ºC gasta menos energía que la sardina de tamaños similares; incrementándose la velocidad a 3 c.p .seg a 17°C.todos los tamaños mayores de 1.5 g de Sardina necesitan más energía que las anchovetas de pesos similares (una sardina de 5 g 1.5 veces y una de 25 g 3.8 veces más). Un cambio de temperatura de 6ºc (de 14° C a 20°c) afecta a ambas especies en una forma diferente : asumiendo una velocidad de natación de 1 cuerpo por segundo, una larva de anchoveta( 0.1 g) tiene que incrementar sus gastos metabólicos dos veces más que la larva de sardina, pero una anchoveta adulta( 40 g)necesita solo un 60% de lo que requiere una sardina del mismo tamaño .

Efectos del tamaño de anzuelo sobre capturas y tallas del perico Coryphaena hippurus

Se evidenció alta selección interespecífica del espinel superficial experimental, al capturar 130 ejemplares de perico Coryphaena hippurus (87,8%) del total de 148 especímenes que incluyeron 8 especies entre peces, tortugas y cefalópodos; como pesca incidental se registró 1 enganche por lance de tortugas (verde Chelonia mydas y amarilla Caretta caretta). El anzuelo más eficiente para la captura de esta especie, fue el de menor calibre (Nº 6) que capturó 24,6%, el menos eficiente fue el Nº 5 (16,9%); sin embargo, mediante el ANOVA de dos vías se estableció que no existía efecto del tamaño de anzuelo sobre el número de ejemplares capturados (p= 0,963). Los anzuelos no evidenciaron una selección de tallas, al no establecerse diferencias significativas entre distribución de tallas (p= 0,538), excepto para los anzuelos Nº 2 y 6 (p= 0,084), al identificarse diferencia por efecto del tamaño de anzuelo. Las longitudes medias estimadas fueron 119,7 cm, 116,8 cm, 118,3 cm, 115,0 cm y 113,7 cm, para los anzuelos Nº 2, 3, 4, 5 y 6, respectivamente. El tamaño de anzuelo mostró un fuerte efecto sobre el tipo de enganche (p= 0,002), presentándose con mayor frecuencia los enganches en la agalla (53,1%) y boca (44,6%). Generalmente los enganches en la agalla son ocasionados por los anzuelos grandes (Nº 2 y 3), mientras que los de boca son realizados por los anzuelos más pequeños (Nº 5 y 6). La captura por unidad de esfuerzo (CPUE) global del longline experimental fue 1,2 ejemplares de perico para un esfuerzo de 1000 anzuelos por hora, lo que representa la tercera parte de la CPUE estimada para la flota comercial.

The normal co-ordinate analysis, vibrational spectra and theoretical infrared intensities of some thiocarbonyl halide molecules /

TITLE: The normal co-ordinate analysis, vibrational spectra and theoretical infrared intensities of some thiocarbonyl halides. AUTHOR: J. L. Brema SUPERVISOR: Dr. D. C. Moule NUMBER OF PAGES: 89 ABSTRACT: The vibrational assignment of the five-in-plane fundamental modes of CSClBr has been made on the basis of infrared gas phase and liquid Raman spectral analyses to supplement our earlier vibrational studies. Even though the one out-of-plane fundamental was not observed spectroscopically an attempt has been made to predict its frequency. The vibrational spectra contained impurity bands and the CSClBr assignment was made only after a thorough analysis of the impurities themselves. A normal co-ordinate analysis calculation was performed assuming a Urey-Bradley force field. This calculation yielded the fundamental frequencies in good agreement with those observed after refinement of the originally transferred force constants. The theoretical frequencies are the eigenvalues of the secular equation and the calculation also gave the corresponding eigenvectors in the form of the very important LLj matrix. The [l] matrix is the transfoirmation between internal co-ordinates and normal co-ordinates and it is essential for Franck-Condon calculations on electronically excited molecules and for infrared Integrated band intensity studies. Using a self-consistent molecular orbital calculation termed "complete neglect of differential overlap" (CNDO/2) , theoretical values of equilibrium bond lengths and angleswere calcuted for a series of carbonyl and thlocarbonyl molecules. From these calculations valence force field force constants were also determined but with limited success. With the CNIX)/2 method theoretical dipole moment derivatives with respect to symmetrized internal co-ordinates were calculated and the results should be useful in a correlation with experimentally determined values.

Changes in the magnitude and pattern of translocation of photoassimilated ¹CO in soybean plants following an acute exposure to gamma radiation /

Young soybean plants (Glycine ~. L. cultivar Harosoy '63), grown under controlled conditions, were exposed to gamma radiation on a single occasion. One hour following exposure to 3,750 rads, the mature trifoliate leaf of the soybean plant was isolated in a closed system and permitted to photoassimilate approximately 1-5 pCi of 14C02 for 15 minutes. After an additional 45 minute-period, the plant was sacrificed and the magnitude of translocation and distribution pattern of 14C determined. In the non-irradiated plants 18~ of the total 14C recovered was outside the fed leaf blades and of this translocated 14c, 28~ was above the node of the fed leaf, 38~ in the stem below the node, 28~ in the roots and 7~ in the petiole. As well, in the irradiated plants, a smaller per cent (6~) of the total 14 C recovered was exported out of the source leaf blades. Of this translocated 14c , a smaller per cent (20~) was found in the apical region above the node of the source leaf and a higher per cent (45~) was recovered from the stem below the node and in the petiole (11~). The per cent of exported 14 C recovered from the root was unaffected by the radiation. Replacement of the shoot apex with 20 ppm IAA immediately following irradiation, only J partially increased the magnitude of translocation but did completely restore the pattern of distribution to that observed in the non-irradiated plants. From supplementary studies showing a radiationinduced reduction of photosynthetic rates in the source leaf and a reduction of the cumulative stem and leaf lengths in the apical sink region, the observed effects of radiation on the translocation process have been correlated to damage incurred by the source and sink regions. These data suggest that the reduction in the magnitude of translocation is the result of damage to both the source and sink regions rather than the phloem conducting tissue itself, whereas the change in the pattern of translocation is probably the result of a reduced rate of 14C-assimilate movement caused by a radiation-induced decrease of sink metabolism, especially the decrease in the metabolism of the apical sink.

Involvement of fimbriae in host-mycoparasite recognition

Extracellular, non-flagellar appendages, termed fimbriae are widespread among fungi. Fungal fimbriae range in diameter from 6-10 nm and exhibit lengths of up to 30 ~m. Fungal fimbriae have been implicated in several functions: adhesion, conjugation and flocculation. A possible role of fimbriae in host-mycoparasite interactions was the focus of this study . Using electron microscopy, fimbriae were observed on the surfaces of Mortiere lla cande labrum, Mortie re lla pusi lla and Phascolomyces articulosus with diameter means of 9.1±0.4 nm, 9.4±0.5 nm and 8.6±0.6 nm, respectively, and lengths of up to 25 ~m. Fimbriae were not observed on the surface of the mycoparasite, Piptocephalis virginiana. Polyclonal antiserum (AU) prepared against the fimbrial protein of Ustilago violacea cross-reacted with 60 and 57 kDa M. candelabrum proteins. In addition, AU cross-reacted with 64 kDa proteins from both M. pusilla and P. articulosus. The proteins that cross-reacted with AU were electroeluted from polyacrylamide gels and were shown to subsequently form fibrils. The diameter means for the electroeluted fibrils were: for M. candelabrum 9.7±0.3 nm, M. pusilla 8.4±0.6 nm and P articulosus 9.2±0.5 nm. Finally, to ascertain the role of fimbriae in host-mycoparasite interactions, AU was incubated with P. virginiana and M. pusilla (mycoparasite/susceptible host) and with P. virginiana and P . articulosus (mycoparasite/ resistant host). It was observed that AU decreased significantly the level of contact between P. virginiana and M. pusilla and between P. virginiana and P. articulosus in comparison to prelmmune serum treatments. Thus, it was proposed that fimbriae might play recognition and attachment roles in early events of mycoparasitism.

Molecular mechanics calculations of tin-bis (triphenylphosphine oxide) complexes

The capability of molecular mechanics for modeling the wide distribution of bond angles and bond lengths characteristic of coordination complexes was investigatecl. This was the preliminary step for future modeling of solvent extraction. Several tin-phosphine oxide COrnI)le:){es were selected as the test groUl) for t.he d,esired range of geometry they eX!libi ted as \-vell as the ligands they cOD.tained r Wllich were c\f interest in connection with solvation. A variety of adjustments were made to Allinger's M:M2 force·-field ill order to inl.prove its performance in the treatment of these systems. A set of u,nique force constants was introduced for' those terms representing the metal ligand bond lengths, bond angles, and, torsion angles. These were significantly smaller than trad.itionallY used. with organic compounds. The ~1orse poteIlt.ial energ'Y function was incorporated for the M-X l')ond lE~ngths and the cosine harmonic potential erlerg-y function was invoked for the MOP bond angle. These functions were found to accomodate the wide distribution of observed values better than the traditional harmonic approximations~ Crystal packing influences on the MOP angle were explored thr"ollgh ttle inclusion of the isolated molecule withil1 a shell cc)ntaini11g tl1e nearest neigl1'bors duri.rlg energy rninimization experiments~ This was found to further improve the fit of the MOP angle.