Large enhanced dielectric permittivity in polyaniline passivated core-shell nano magnetic iron oxide by plasma polymerization

Commercial samples of Magnetite with size ranging from 25–30nm were coated with polyaniline by using radio frequency plasma polymerization to achieve a core shell structure of magnetic nanoparticle (core)–Polyaniline (shell). High resolution transmission electron microscopy images confirm the core shell architecture of polyaniline coated iron oxide. The dielectric properties of the material were studied before and after plasma treatment. The polymer coated magnetite particles exhibited a large dielectric permittivity with respect to uncoated samples. The dielectric behavior was modeled using a Maxwell–Wagner capacitor model. A plausible mechanism for the enhancement of dielectric permittivity is proposed

Spray pyrolysed In2S3 thin films: A potential electron selective layer for large area inverted bulk-heterojunction polymer solar cells

In this paper, we report the results of investigations on the potential of spray pyrolysis technique in depositing electron selective layer over larger area for the fabrication of inverted bulk-heterojunction polymer solar cells. The electron selective layer (In2S3) was deposited using spray pyrolysis technique and the linear heterojunction device thus fabricated exhibited good uniformity in photovoltaic properties throughout the area of the device. An MEH-PPV:PCBM inverted bulk-heterojunction device with In2S3 electron selective layer (active area of 3.25 3.25 cm2) was also fabricated and tested under indoor and outdoor conditions. Fromthe indoor measurements employing a tungsten halogen lamp (50mW/cm2 illumination), an opencircuit voltage of 0.41V and a short-circuit current of 5.6mA were obtained. On the other hand, the outdoor measurements under direct sunlight (74mW/cm2) yielded an open-circuit voltage of 0.46V and a short-circuit current of 9.37mA

Marine yeast Candida MCCF 101 as feed supplement in aquaculture: nutritional quality, optimization of large scale production and evaluation of its protective effect on Koi carp from Aeromonas infection

Marine yeast have been regarded as safe and showing a beneficial impact on biotechnological process. It provides better nutritional and dietary values indicating their potential application as feed supplements in aquaculture. Brown et al. (1996) evaluated all the marine yeasts characterised with high protein content, carbohydrate, good amino acid composition and high levels of saturated fats. However, there is paucity of information on marine yeasts as feed supplements and no feed formulation has been found either in literature or in market supplemented with them. This statement supported by Zhenming et al. (2006) reported still a lack of feed composed of single cell protein (SCP) from marine yeasts with high content of protein and other nutrients. Recent research has shown that marine yeasts also have highly potential uses in food, feed, medical and biofuel industries as well as marine biotechnology (Chi et al., 2009; 2010). Sajeevan et al. (2006; 2009a) and Sarlin and Philip (2011) demonstrates that the marine yeasts Candida sake served as a high quality, inexpensive nutrient source and it had proven immunostimulatory properties for cultured shrimps. This strain has been made part of the culture collection of National Centre for Aquatic Animal Health, Cochin University of Science and Technology as Candida MCCF 101. Over the years marine yeasts have been gaining increased attention in animal feed industry due to their nutritional value and immune boosting property.Therefore, the present study was undertaken, and focused on the nutritional quality, optimization of large scale production and evaluation of its protective effect on Koi carp from Aeromonas infection

Integron study, molecular typing and characterization of Salmonella serotypes isolated from seafood and poultry

The primary habitat of Salmonella is the gastrointestinal tract of animals and they are discharged into the water bodies through the feces. Aquatic animals act as asymptomatic reservoirs of a wide range of Salmonella serotypes. The inevitable delay in the detection of Salmonella contamination and the low sensitivity of the conventional methods is a serious issue in the seafood industry. Due to the indiscriminate use, the antibiotics are finally accumulated in the aquatic environment which provides the required antibiotic stress for the emergence of more and more antibiotic resistant phenotypes ofSalmonella. Several genetic determinants like integrons, genomic islands etc. play their role in acquisition and reshuffling of antibiotic resistance genes. A large number of virulence determinants are required for Salmonella pathogenicity. The virulence potential of Salmonella is determined, to some extent, by the presence of phages or phage mediated genes in the bacterial genome. There is much intra-serotype polymorphism in Salmonella and epidemiological studies rely on genetic resemblance of the isolated strains. Proper identification of the strain employing the traditional and molecular techniques is a prerequisite for accurate epidemiological studies (Soto et al., 2000). In this context, a study was undertaken to determine the prevalence of different Salmonella serotypes in seafood and to characterize them

Distribution, extracellular virulence factors and antibiogram of motile aeromonads in fresh water ornamental fishes and immune response of Cyprinus carpio against Aeromonas hydrophila infection

The thesis deals with the prevalence and distribution of motile aeromonads in selected ornamental fishes. The presence of motile aeromonads in ornamental fishes and associated carriage water is well documented. Though aeromonads are a part of autochthonous flora of natural waters, disease outbreak occurs as a result of environmental stress on the cultured species and virulence of the pathogens. While ornamental aquaculture in many parts of the world is highly organized and practiced scientifically, it is highly unorganized in India. The culture ponds/tanks are often maintained in very poor manner and the fishes are subjected to high degree of stress during transportation from the production facility to retail vendors. The situation is no better at retail outlets, where fishes are maintained in crowded condition without proper aeration or food. All these could result in high prevalence of diseases caused by motile aeromonads. No systematic study has been carried out to understand the prevalence of motile aeromonads in ornamental fishes and carriage water . It also gives an account of the production of extracellular virulence factors and the antibiogram of the different species of motile aeromonads isolated. The growth characteristics and virulence potential of a representative strain of Aeromonas hydrophila is also studied. The nucleotide sequencing of the strain was carried out and sequences deposited in Genbank. Survival and immune response of Cyprinus carpio under different stress conditions and on probiotic treatment with Bacillus NL110, when challenged with A. hydrophila is also dealt within this thesis.

Smart electricity networks based on large integration of renewable sources and distributed generation

Das Grünbuch 2006 der Europäischen Kommission "Eine Europäische Strategie für nachhaltige, wettbewerbsfähige und sichere Energie" unterstreicht, dass Europa in ein neues Energie-Zeitalter eingetreten ist. Die vorrangigen Ziele europäischer Energiepolitik müssen Nachhaltigkeit, Wettbewerbsfähigkeit und Versorgungssicherheit sein, wobei sie eine zusammenhängende und logische Menge von Taktiken und Maßnahmen benötigt, um diese Ziele zu erreichen. Die Strommärkte und Verbundnetze Europas bilden das Kernstück unseres Energiesystems und müssen sich weiterentwickeln, um den neuen Anforderungen zu entsprechen. Die europäischen Stromnetze haben die lebenswichtigen Verbindungen zwischen Stromproduzenten und Verbrauchern mit großem Erfolg seit vielen Jahrzehnten gesichert. Die grundlegende Struktur dieser Netze ist entwickelt worden, um die Bedürfnisse großer, überwiegend auf Kohle aufgebauten Herstellungstechnologien zu befriedigen, die sich entfernt von den Verbraucherzentren befinden. Die Energieprobleme, denen Europa jetzt gegenübersteht, ändern die Stromerzeugungslandschaft in zwei Gesichtspunkten: die Notwendigkeit für saubere Kraftwerkstechnologien verbunden mit erheblich verbesserten Wirkungsgraden auf der Verbraucherseite wird es Kunden ermöglichen, mit den Netzen viel interaktiver zu arbeiten; andererseits müssen die zukünftigen europaweiten Stromnetze allen Verbrauchern eine höchst zuverlässige, preiswerte Energiezufuhr bereitstellen, wobei sowohl die Nutzung von großen zentralisierten Kraftwerken als auch kleineren lokalen Energiequellen überall in Europa ausgeschöpft werden müssen. In diesem Zusammenhang wird darauf hingewiesen, dass die Informationen, die in dieser Arbeit dargestellt werden, auf aktuellen Fragen mit großem Einfluss auf die gegenwärtigen technischen und wirtschaftspolitischen Diskussionen basieren. Der Autor hat während der letzten Jahre viele der hier vorgestellten Schlussfolgerungen und Empfehlungen mit Vertretern der Kraftwerksindustrie, Betreibern von Stromnetzen und Versorgungsbetrieben, Forschungsgremien und den Regulierungsstellen diskutiert. Die folgenden Absätze fassen die Hauptergebnisse zusammen: Diese Arbeit definiert das neue Konzept, das auf mehr verbraucherorientierten Netzen basiert, und untersucht die Notwendigkeiten sowie die Vorteile und die Hindernisse für den Übergang auf ein mögliches neues Modell für Europa: die intelligenten Stromnetze basierend auf starker Integration erneuerbarer Quellen und lokalen Kleinkraftwerken. Das neue Modell wird als eine grundlegende Änderung dargestellt, die sich deutlich auf Netzentwurf und -steuerung auswirken wird. Sie fordert ein europäisches Stromnetz mit den folgenden Merkmalen: – Flexibel: es erfüllt die Bedürfnisse der Kunden, indem es auf Änderungen und neue Forderungen eingehen kann – Zugänglich: es gestattet den Verbindungszugang aller Netzbenutzer besonders für erneuerbare Energiequellen und lokale Stromerzeugung mit hohem Wirkungsgrad sowie ohne oder mit niedrigen Kohlendioxidemissionen – Zuverlässig: es verbessert und garantiert die Sicherheit und Qualität der Versorgung mit den Forderungen des digitalen Zeitalters mit Reaktionsmöglichkeiten gegen Gefahren und Unsicherheiten – Wirtschaftlich: es garantiert höchste Wirtschaftlichkeit durch Innovation, effizientes Energiemanagement und liefert „gleiche Ausgangsbedingungen“ für Wettbewerb und Regulierung. Es beinhaltet die neuesten Technologien, um Erfolg zu gewährleisten, während es die Flexibilität behält, sich an weitere Entwicklungen anzupassen und fordert daher ein zuversichtliches Programm für Forschung, Entwicklung und Demonstration, das einen Kurs im Hinblick auf ein Stromversorgungsnetz entwirft, welches die Bedürfnisse der Zukunft Europas befriedigt: – Netztechnologien, die die Stromübertragung verbessern und Energieverluste verringern, werden die Effizienz der Versorgung erhöhen, während neue Leistungselektronik die Versorgungsqualität verbessern wird. Es wird ein Werkzeugkasten erprobter technischer Lösungen geschaffen werden, der schnell und wirtschaftlich eingesetzt werden kann, so dass bestehende Netze Stromeinleitungen von allen Energieressourcen aufnehmen können. – Fortschritte bei Simulationsprogrammen wird die Einführung innovativer Technologien in die praktische Anwendung zum Vorteil sowohl der Kunden als auch der Versorger stark unterstützen. Sie werden das erfolgreiche Anpassen neuer und alter Ausführungen der Netzkomponenten gewährleisten, um die Funktion von Automatisierungs- und Regelungsanordnungen zu garantieren. – Harmonisierung der ordnungspolitischen und kommerziellen Rahmen in Europa, um grenzüberschreitenden Handel von sowohl Energie als auch Netzdienstleistungen zu erleichtern; damit muss eine Vielzahl von Einsatzsituationen gewährleistet werden. Gemeinsame technische Normen und Protokolle müssen eingeführt werden, um offenen Zugang zu gewährleisten und den Einsatz der Ausrüstung eines jeden Herstellers zu ermöglichen. – Entwicklungen in Nachrichtentechnik, Mess- und Handelssystemen werden auf allen Ebenen neue Möglichkeiten eröffnen, auf Grund von Signalen des Marktes frühzeitig technische und kommerzielle Wirkungsgrade zu verbessern. Es wird Unternehmen ermöglichen, innovative Dienstvereinbarungen zu benutzen, um ihre Effizienz zu verbessern und ihre Angebote an Kunden zu vergrößern. Schließlich muss betont werden, dass für einen erfolgreichen Übergang zu einem zukünftigen nachhaltigen Energiesystem alle relevanten Beteiligten involviert werden müssen.

Influence of the buffer environment on the Relative Biological Effectiveness of carbon ion radiation, investigated by Scanning Force Microscopy and gel electrophoresis

This work focuses on the analysis of the influence of environment on the relative biological effectiveness (RBE) of carbon ions on molecular level. Due to the high relevance of RBE for medical applications, such as tumor therapy, and radiation protection in space, DNA damages have been investigated in order to understand the biological efficiency of heavy ion radiation. The contribution of this study to the radiobiology research consists in the analysis of plasmid DNA damages induced by carbon ion radiation in biochemical buffer environments, as well as in the calculation of the RBE of carbon ions on DNA level by mean of scanning force microscopy (SFM). In order to study the DNA damages, besides the common electrophoresis method, a new approach has been developed by using SFM. The latter method allows direct visualisation and measurement of individual DNA fragments with an accuracy of several nanometres. In addition, comparison of the results obtained by SFM and agarose gel electrophoresis methods has been performed in the present study. Sparsely ionising radiation, such as X-rays, and densely ionising radiation, such as carbon ions, have been used to irradiate plasmid DNA in trishydroxymethylaminomethane (Tris buffer) and 4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid (HEPES buffer) environments. These buffer environments exhibit different scavenging capacities for hydroxyl radical (HO0), which is produced by ionisation of water and plays the major role in the indirect DNA damage processes. Fragment distributions have been measured by SFM over a large length range, and as expected, a significantly higher degree of DNA damages was observed for increasing dose. Also a higher amount of double-strand breaks (DSBs) was observed after irradiation with carbon ions compared to X-ray irradiation. The results obtained from SFM measurements show that both types of radiation induce multiple fragmentation of the plasmid DNA in the dose range from D = 250 Gy to D = 1500 Gy. Using Tris environments at two different concentrations, a decrease of the relative biological effectiveness with the rise of Tris concentration was observed. This demonstrates the radioprotective behavior of the Tris buffer solution. In contrast, a lower scavenging capacity for all other free radicals and ions, produced by the ionisation of water, was registered in the case of HEPES buffer compared to Tris solution. This is reflected in the higher RBE values deduced from SFM and gel electrophoresis measurements after irradiation of the plasmid DNA in 20 mM HEPES environment compared to 92 mM Tris solution. These results show that HEPES and Tris environments play a major role on preventing the indirect DNA damages induced by ionising radiation and on the relative biological effectiveness of heavy ion radiation. In general, the RBE calculated from the SFM measurements presents higher values compared to gel electrophoresis data, for plasmids irradiated in all environments. Using a large set of data, obtained from the SFM measurements, it was possible to calculate the survive rate over a larger range, from 88% to 98%, while for gel electrophoresis measurements the survive rates have been calculated only for values between 96% and 99%. While the gel electrophoresis measurements provide information only about the percentage of plasmids DNA that suffered a single DSB, SFM can count the small plasmid fragments produced by multiple DSBs induced in a single plasmid. Consequently, SFM generates more detailed information regarding the amount of the induced DSBs compared to gel electrophoresis, and therefore, RBE can be calculated with more accuracy. Thus, SFM has been proven to be a more precise method to characterize on molecular level the DNA damage induced by ionizing radiations.

Large-Size AlGaN/GaN HEMT Large-Signal Electrothermal Characterization and Modeling for Wireless Digital Communications

The rapid growth in high data rate communication systems has introduced new high spectral efficient modulation techniques and standards such as LTE-A (long term evolution-advanced) for 4G (4th generation) systems. These techniques have provided a broader bandwidth but introduced high peak-to-average power ratio (PAR) problem at the high power amplifier (HPA) level of the communication system base transceiver station (BTS). To avoid spectral spreading due to high PAR, stringent requirement on linearity is needed which brings the HPA to operate at large back-off power at the expense of power efficiency. Consequently, high power devices are fundamental in HPAs for high linearity and efficiency. Recent development in wide bandgap power devices, in particular AlGaN/GaN HEMT, has offered higher power level with superior linearity-efficiency trade-off in microwaves communication. For cost-effective HPA design to production cycle, rigorous computer aided design (CAD) AlGaN/GaN HEMT models are essential to reflect real response with increasing power level and channel temperature. Therefore, large-size AlGaN/GaN HEMT large-signal electrothermal modeling procedure is proposed. The HEMT structure analysis, characterization, data processing, model extraction and model implementation phases have been covered in this thesis including trapping and self-heating dispersion accounting for nonlinear drain current collapse. The small-signal model is extracted using the 22-element modeling procedure developed in our department. The intrinsic large-signal model is deeply investigated in conjunction with linearity prediction. The accuracy of the nonlinear drain current has been enhanced through several issues such as trapping and self-heating characterization. Also, the HEMT structure thermal profile has been investigated and corresponding thermal resistance has been extracted through thermal simulation and chuck-controlled temperature pulsed I(V) and static DC measurements. Higher-order equivalent thermal model is extracted and implemented in the HEMT large-signal model to accurately estimate instantaneous channel temperature. Moreover, trapping and self-heating transients has been characterized through transient measurements. The obtained time constants are represented by equivalent sub-circuits and integrated in the nonlinear drain current implementation to account for complex communication signals dynamic prediction. The obtained verification of this table-based large-size large-signal electrothermal model implementation has illustrated high accuracy in terms of output power, gain, efficiency and nonlinearity prediction with respect to standard large-signal test signals.

Designing a Robust Pitch Angle Controller for a 2‐Motor‐Pitch‐System in a Large Wind Turbine

Für große Windenergieanlagen werden neue Pitchregler wie Einzelblattregler oder Turmdämpfungsregler entwickelt. Während diese neuen Pitchregler die Elemente der Windenergieanlagen entlasten, wird das Pitchantriebssystem stärker belastet. Die Pitchantriebe müssen weitaus häufiger bei höherer Amplitude arbeiten. Um die neuen Pitchregler nutzen zu können, muss zunächst das Problem der Materialermüdung der Pitchantriebssysteme gelöst werden. Das Getriebespiel in Getrieben und zwischen Ritzeln und dem Zahnkranz erhöht die Materialermüdung in den Pitchantriebssystemen. In dieser Studie werden als Lösung zwei Pitchantriebe pro Blatt vorgeschlagen. Die beiden Pitchantriebe erzeugen eine Spannung auf dem Pitchantriebssystem und kompensieren das Getriebespiel. Drehmomentspitzen, die eine Materialermüdung verursachen, treten bei diesem System mit zwei Pitchmotoren nicht mehr auf. Ein Reglerausgang wird via Drehmomentverteiler auf die beiden Pitchantriebe übertragen. Es werden mehrere Methoden verglichen und der leistungsfähigste Drehmomentverteiler ausgewählt. Während die Pitchantriebe in Bewegung sind, ändert sich die Spannung auf den Getrieben. Die neuen Pitchregler verstellen den Pitchwinkel in einer sinusförmigen Welle. Der Profilgenerator, der derzeit als Pitchwinkelregler verwendet wird, kann eine Phasenverzögerung im sinusförmigen Pitchwinkel verursachen. Zusätzlich erzeugen große Windenergieanlagen eine hohe Last, die sich störend auf die Pitchbewegung auswirkt. Änderungen der viskosen Reibung und Nichtlinearität der Gleitreibung bzw. Coulombsche Reibung des Pitchregelsystems erschweren zudem die Entwicklung eines Pitchwinkelreglers. Es werden zwei robuste Regler (H∞ und μ–synthesis ) vorgestellt und mit zwei herkömmlichen Reglern (PD und Kaskadenregler) verglichen. Zur Erprobung des Pitchantriebssystems und des Pitchwinkelreglers wird eine Prüfanordnung verwendet. Da der Kranz nicht mit einem Positionssensor ausgestattet ist, wird ein Überwachungselement entwickelt, das die Kranzposition meldet. Neben den beiden Pitchantrieben sind zwei Lastmotoren mit dem Kranz verbunden. Über die beiden Lastmotoren wird das Drehmoment um die Pitchachse einer Windenergieanlage simuliert. Das Drehmoment um die Pitchachse setzt sich zusammen aus Schwerkraft, aerodynamischer Kraft, zentrifugaler Belastung, Reibung aufgrund des Kippmoments und der Beschleunigung bzw. Verzögerung des Rotorblatts. Das Blatt wird als Zweimassenschwinger modelliert. Große Windenergieanlagen und neue Pitchregler für die Anlagen erfordern ein neues Pitchantriebssystem. Als Hardware-Lösung bieten sich zwei Pitchantriebe an mit einem robusten Regler als Software.

Optimization in the Technological Steps for the Fabrication of Large Area Micromirror Arrays

Micromirror arrays are a very strong candidate for future energy saving applications. Within this work, the fabrication process for these micromirror arrays has been optimized and some steps for the large area fabrication of micromirror modules were performed. At first the surface roughness of the insulation layer of silicon dioxide (SiO2) was investigated. This SiO2 thin layer was deposited on three different type of substrates i.e. silicon, glass and Polyethylene Naphthalate (PEN) substrates. The deposition techniques which has been used are Plasma Enhanced Chemical Vapor Deposition (PECVD), Physical Vapor Deposition (PVD) and Ion Beam Sputter Deposition (IBSD). The thickness of the SiO2 thin layer was kept constant at 150nm for each deposition process. The surface roughness was measured by Stylus Profilometry and Atomic Force Microscopy (AFM). It was found that the layer which was deposited by IBSD has got the minimum surface roughness value and the layer which was deposited by PECVD process has the highest surface roughness value. During the same investigation, the substrate temperature of PECVD was varied from 80° C to 300° C with the step size of 40° C and it was found that the surface roughness keeps on increasing as the substrate holder temperature increases in the PECVD process. A new insulation layer system was proposed to minimize the dielectric breakdown effect in insulation layer for micromirror arrays. The conventional bilayer system was replaced by five layer system but the total thickness of insulation layer remains the same. It was found that during the actuation of micromirror arrays structure, the dielectric breakdown effect was reduced considerably as compared to the bilayer system. In the second step the fabrication process of the micromirror arrays was successfully adapted and transferred from glass substrates to the flexible PEN substrates by optimizing the conventional process recipe. In the last section, a large module of micromirror arrays was fabricated by electrically interconnecting four 10cm×10cm micromirror modules on a glass pane having dimensions of 21cm×21cm.

Small and Closed vs. Large and Open: Some Lessons from Comparing Cuban to Colombian Agricultural Development

Comparing the experiences of selected Latin America and the Caribbean countries and their trajectories over the past 15 years offers rich insights into the dynamics and causes for not meeting the 2015 MDGs. They also offer clues for post-MDG strategies. Central to achieving sustainable growth are government policies able to support small and medium-sized farms and peasants, as they are crucial for the achievement of several goals, centrally: to achieve food security; to provide a sound and stable rural environment able to resist external (financial) shocks; to secure healthy food; to secure local food; and to protect vibrant and culturally rich local communities. This paper analyses and compares the most successful government policies to the least successful policies carried out over the last 15 years in selected Latin American and Caribbean countries and based on this analysis, offers strategies for more promising post-MDG politics, able to reduce poverty, reduce inequality, fight back informality, and achieve more decent work in poor countries.

Local map update for large scale SLAM

A technique for simultaneous localisation and mapping (SLAM) for large scale scenarios is presented. This solution is based on the use of independent submaps of a limited size to map large areas. In addition, a global stochastic map, containing the links between adjacent submaps, is built. The information in both levels is corrected every time a loop is closed: local maps are updated with the information from overlapping maps, and the global stochastic map is optimised by means of constrained minimisation

Large-Area Photo-Mosaics Using Global Alignment and Navigation Data

Seafloor imagery is a rich source of data for the study of biological and geological processes. Among several applications, still images of the ocean floor can be used to build image composites referred to as photo-mosaics. Photo-mosaics provide a wide-area visual representation of the benthos, and enable applications as diverse as geological surveys, mapping and detection of temporal changes in the morphology of biodiversity. We present an approach for creating globally aligned photo-mosaics using 3D position estimates provided by navigation sensors available in deep water surveys. Without image registration, such navigation data does not provide enough accuracy to produce useful composite images. Results from a challenging data set of the Lucky Strike vent field at the Mid Atlantic Ridge are reported

Visual SLAM for 3D large-scale seabed acquisition employing underwater vehicles

This paper presents a novel technique to align partial 3D reconstructions of the seabed acquired by a stereo camera mounted on an autonomous underwater vehicle. Vehicle localization and seabed mapping is performed simultaneously by means of an Extended Kalman Filter. Passive landmarks are detected on the images and characterized considering 2D and 3D features. Landmarks are re-observed while the robot is navigating and data association becomes easier but robust. Once the survey is completed, vehicle trajectory is smoothed by a Rauch-Tung-Striebel filter obtaining an even better alignment of the 3D views and yet a large-scale acquisition of the seabed