Electrochemical Impedance Spectroscopy Of Peo Coating On Aluminum Alloy In Nacl Solution

Various Plasma Electrolytic Oxidation (PEO) ceramic coatings were prepared on LY12 aluminum alloy by adjusting the concentration of sodium silicate solution. Optical microscope (OM), XRD and EIS were used to study their morphology, composition and anti corrosion behavior in NaCl solution. Increasing concentration of sodium silicate leads to the increase of the total coating thickness while too high and too low concentration lead to the decrease of inner dense layer. The main composition of PEO coatings prepared in 20, 40 and above 60g/L concentration solution are correspondingly alumina, alumina with mullite, and amorphous phase. The corrosion resistance is determined by the inner dense layer. Increasing the thickness of inner dense layer can improve the anti-corrosion performance. PEO coating's corrosion resistance in acidic, alkaline and neutral NaCl solution is proved and the corrosion mechanism involved is also discussed.

Interface Fracture Property Of Peo Ceramic Coatings On Aluminum Alloy

This paper combines the four-point bending test, SEM and finite element method to study the interface fracture property of PEO coatings on aluminum alloy. The interface failure mode of the coating on the compression side is revealed. The ceramic coating crack firstly along the 45 degrees to the interface, then the micro crack in the coating deduces the interface crack. The plastic deformation observed by SEM shows excellent adhesion property between the coating and substrate. The plastic deformation in the substrate is due to the interfacial crack extension, so the interface crack mode of PEO coatings is ductile crack. The results of FEM show that the compression strength is about 600 MPa. (C) 2008 Elsevier B.V. All rights reserved.

塑性变形对热镀锌板耐蚀性的影响

为了研究塑性变形对热镀锌板耐蚀性的影响,用称量法测试了不同塑性变形状态下的热镀锌板在5%NaCl溶液全浸腐蚀试验中的腐蚀速率,发现全浸蚀腐蚀试验7周后,原始镀锌板质量下降0.09%,拉伸应变为10%的镀锌板质量下降0.22%,腐蚀程度是前者的2.4倍.结果表明,塑性变形会降低热镀锌板的耐蚀性,而耐蚀性的降低是由塑性变形引起的裂纹密度的增加所致.

Formation and Structure of Composite Coating of HAD and Micro-Plasma Oxidation on A3 Steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HAD) at 720 degreesC for 6 min and micro-plasma oxidation (MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HAD/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, At and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the At surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HAD process. Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HAD/MPO treatment.

Analytical Methods of Residual Strength in Injecting Water Pipeline

In this paper, common criterions about residual strength evaluation at home and abroad are generalized and seven methods are acquired, namely ASME-B31G, DM, Wes-2805-97, CVDA-84, Burdekin, Irwin and J integral methods. BP neural network are Combined with Genetic Algorithm (GA) named by modified BP-GA methods to successfully predict residual strength and critical pressure of injecting water, corrosion pipelines. Examples are shown that calculation results of every kind of method have great difference and calculating values of Wes-2805-97 criterion, ASME-B31G criterion, CVDA-84 criterion and Irwin fracture mechanics model are conservative and higher than, those of J integral methods while calculating values of Burdiken model and DM fracture mechanics model are dangerous and less than those of J integral methods and calculating values of modified BP-GA methods are close and moderate to those of J integral methods. Therefore modified BP-GA methods and J integral methods are considered better methods to calculate residual strength and critical pressure of injecting water corrosion pipelines

Multi-pipe string electromagnetic detection tool and its applications

The MID-K, a new kind of multi-pipe string detection tool is introduced. This tool provides a means of evaluating the condition of in-place pipe string, such as tubing and casino. It is capable of discriminating the defects of the inside and outside, and estimating the thickness of tubing and casing. It is accomplished by means of a low frequency eddy current to detect flaws on the inner surface and a magnetic flux leakage to inspect the full thickness. The measurement principle, the technology and applications are presented in this paper.

纳米晶Ni晶间断裂的数值模拟

提出了一种针对超细晶和纳米晶金属(主要是fcc金属)晶间断裂的微结构计算模型,即采用基于机制的应变梯度塑性(CMSG)理论描述晶粒内部材料塑性变形过程中的变形、强化和尺度效应;采用黏聚力界面模型来模拟晶界的滑移和分离现象,以及晶间裂纹的萌生和演化,直至晶间断裂导致的材料失效.利用该计算模型模拟了纳米晶Ni的拉伸实验过程,对纳米晶Ni宏观力学行为和晶间微裂纹萌生与扩展之间的关系进行了研究,验证了针对超细晶和纳米晶力学性能的计算模型的有效性;同时,模拟结果表明,非均匀塑性变形导致高应变梯度效应,晶粒塑性变形强化显著,使晶界主导的变形机制对纳米晶金属的整体力学性能产生重要影响.

The formation mechanism of low leaching glassy slag during plasma arc vitrification treatment of fly ash

In this paper, the glass formation theory is applied to study the formation mechanism of the low leaching glassy slag during the process of plasma waste treatment. The research shows that SiO2 acts as network former to form a 3-dimensional Si-O tetrahedral network in which heavy metals are bonded or encapsulated, so the Si-O tetrahedron protect heavy metals against leaching from the vitrified slag or acid corrosion. For given chemical compositions of waste, the formation ability of the vitrified slag can be represented by the ratio of the whole oxygen ions to the whole network former ions in glass (O/Si) which is appropriate in the range of 2~3. A plasma arc reactor is used to conduct the vitrification experiments of two kinds of fly ashes with additives in which effects of various parameters including arc power, cooling speed, treatment temperature are studied. The chemical compositions of fly ashes are analyzed by X-ray fluorescence (XRF) spectrometry. The experimental results show that both cooling speed and O/Si have important influence on the formation of the vitrified slag, which is qualitatively in accordance with the predictions of the glass formation theory.

Developing and characterizing bulk metallic glasses for extreme applications

Metallic glasses have typically been treated as a “one size fits all” type of material. Every alloy is considered to have high strength, high hardness, large elastic limits, corrosion resistance, etc. However, similar to traditional crystalline materials, properties are strongly dependent upon the constituent elements, how it was processed, and the conditions under which it will be used. An important distinction which can be made is between metallic glasses and their composites. Charpy impact toughness measurements are performed to determine the effect processing and microstructure have on bulk metallic glass matrix composites (BMGMCs). Samples are suction cast, machined from commercial plates, and semi-solidly forged (SSF). The SSF specimens have been found to have the highest impact toughness due to the coarsening of the dendrites, which occurs during the semi-solid processing stages. Ductile to brittle transition (DTBT) temperatures are measured for a BMGMC. While at room temperature the BMGMC is highly toughened compared to a fully glassy alloy, it undergoes a DTBT by 250 K. At this point, its impact toughness mirrors that of the constituent glassy matrix. In the following chapter, BMGMCs are shown to have the capability of being capacitively welded to form single, monolithic structures. Shear measurements are performed across welded samples, and, at sufficient weld energies, are found to retain the strength of the parent alloy. Cross-sections are inspected via SEM and no visible crystallization of the matrix occurs.

Next, metallic glasses and BMGMCs are formed into sheets and eggbox structures are tested in hypervelocity impacts. Metallic glasses are ideal candidates for protection against micrometeorite orbital debris due to their high hardness and relatively low density. A flat single layer, flat BMG is compared to a BMGMC eggbox and the latter creates a more diffuse projectile cloud after penetration. A three tiered eggbox structure is also tested by firing a 3.17 mm aluminum sphere at 2.7 km/s at it. The projectile penetrates the first two layers, but is successfully contained by the third.

A large series of metallic glass alloys are created and their wear loss is measured in a pin on disk test. Wear is found to vary dramatically among different metallic glasses, with some considerably outperforming the current state-of-the-art crystalline material (most notably Cu₄₃Zr₄₃Al₇Be₇). Others, on the other hand, suffered extensive wear loss. Commercially available Vitreloy 1 lost nearly three times as much mass in wear as alloy prepared in a laboratory setting. No conclusive correlations can be found between any set of mechanical properties (hardness, density, elastic, bulk, or shear modulus, Poisson’s ratio, frictional force, and run in time) and wear loss. Heat treatments are performed on Vitreloy 1 and Cu₄₃Zr₄₃Al₇Be₇. Anneals near the glass transition temperature are found to increase hardness slightly, but decrease wear loss significantly. Crystallization of both alloys leads to dramatic increases in wear resistance. Finally, wear tests under vacuum are performed on the two alloys above. Vitreloy 1 experiences a dramatic decrease in wear loss, while Cu₄₃Zr₄₃Al₇Be₇ has a moderate increase. Meanwhile, gears are fabricated through three techniques: electrical discharge machining of 1 cm by 3 mm cylinders, semisolid forging, and copper mold suction casting. Initial testing finds the pin on disk test to be an accurate predictor of wear performance in gears.

The final chapter explores an exciting technique in the field of additive manufacturing. Laser engineered net shaping (LENS) is a method whereby small amounts of metallic powders are melted by a laser such that shapes and designs can be built layer by layer into a final part. The technique is extended to mixing different powders during melting, so that compositional gradients can be created across a manufactured part. Two compositional gradients are fabricated and characterized. Ti 6Al¬ 4V to pure vanadium was chosen for its combination of high strength and light weight on one end, and high melting point on the other. It was inspected by cross-sectional x-ray diffraction, and only the anticipated phases were present. 304L stainless steel to Invar 36 was created in both pillar and as a radial gradient. It combines strength and weldability along with a zero coefficient of thermal expansion material. Only the austenite phase is found to be present via x-ray diffraction. Coefficient of thermal expansion is measured for four compositions, and it is found to be tunable depending on composition.

Comportamento do titânio comercialmente puro obtido por diferentes processamentos submetidos a soluções fluoretadas

O objetivo deste estudo in vitro foi analisar o comportamento superficial do titânio comercialmente puro (grau 2 ASTM) usinado e obtido pelo processamento de metalurgia do pó sob a ação de diferentes soluções fluoretadas, através da análise do grau de corrosão em microscopia óptica (MO) e da rugosidade superficial. Além disso, o estudo se propôs a comparar essas análises com os resultados obtidos com o titânio fundido da dissertação de mestrado de Barros (2004). Todas as amostras receberam procedimento metalográfico padrão e foram divididas em grupos: Gr.1- saliva artificial com pH 7.0 (controle), Gr.2- gel de flúor fosfato acidulado a 1,23% com pH 3.5, Gr.3- gel de NaF a 2% com pH 6.5, Gr.4- solução de NaF a 0,05% com pH 4.0 e Gr.5- solução de NaF a 0,05% com pH 7.5. As amostras foram expostas a estas soluções por 1, 4, 8 e 16 min, intercaladas com imersão em saliva artificial por 24 h, e depois foram observadas em MO e MEV, a cada intervalo de tempo. As imagens em MO, 100x, foram classificadas através de escores de 0 a 4, conforme o grau de corrosão. A rugosidade foi analisada utilizando o parâmetro Ra. Os resultados da análise de MO foram tratados estatisticamente pelo teste qui-quadrado e da rugosidade pelo teste F de Snedecor e de Bonferroni (p<0,05). Nos três tipos de amostras, o Gr2 apresentou a corrosão mais severa, e os Gr.4 e 5 apresentaram os menores graus de corrosão. Entretanto, nas amostras usinadas o Gr5 apresentou uma corrosão menos acentuada em relação ao Gr4. No Gr3 houve um aumento da corrosão em função do tempo, sendo que as amostras fundidas mostraram este aumento mais rapidamente. Houve um aumento significativo na rugosidade superficial no Gr.2 nos três tipos de amostras. Nos diversos grupos, os valores de rugosidade superficial das amostras fundidas foram significantemente maiores que os das usinadas e as de metalurgia do pó. Os autores concluíram que as soluções fluoretadas de uso odontológico são danosas às superfícies do titânio fundido, usinado e metalurgia do pó, principalmente as soluções com alta concentração de fluoreto.

Análisis del proceso de friction drilling. Viabilidad de la unión de materiales disimilares en uniones atornilladas sin tuerca, compatibilidad de la unión

[ES]En este trabajo se expone un estudio experimental del proceso de taladrado por fricción, más conocido como Friction Drilling y posterior roscado por laminación, en uniones de chapas de acero y aluminio, muy utilizadas en multitud de sectores, que se caracteriza por la ausencia de tuercas. La base de esta técnica es el calor producido por el rozamiento al entrar en contacto la herramienta rotativa con el material, causando el reblandecimiento del material, la fluencia y la deformación de éste. De este modo, se generará una copa cónica, que se roscará por laminación. En este trabajo se va a estudiar la viabilidad del proceso experimentalmente, obteniendo variables de entrada del proceso óptimas que generen una unión de calidad, atendiendo a diferentes aspectos. Sin embargo, se centra sobre todo en analizar la calidad de la unión en lo que se refiere a la compatibilidad de los materiales. Se estudiará la corrosión galvánica por una parte entre acero y aluminio y, por otra parte, entre acero, aluminio y el material del tornillo. Una vez concluido el trabajo, se espera obtener un proceso de unión de materiales disímiles sin tuerca, ofreciendo una mayor calidad que los procesos implementados actualmente.

Monitoramento microbiológico e físico-químico de tanques de armazenamento de óleo e água

A injeção da água do mar nos campos marítimos (offshore), processo este conhecido como recuperação secundária de petróleo, gera muitos resíduos e efluentes. Dentre estes, pode-se destacar a água produzida, que consiste de água de formação, água naturalmente presente na formação geológica do reservatório de petróleo, e água de injeção, aquela normalmente injetada no reservatório para aumento de produção. Sete tanques de armazenamento de água/óleo de um terminal foram monitorados quanto à presença de micro-organismos e teores de sulfato, sulfeto, pH e condutividade. Particularmente, as bactérias redutoras de sulfato (BRS), que agem às expensas da atividade de outras espécies, reduzindo sulfato à sulfeto, constituindo-se num problema-chave. Os tanques de óleo codificados como Verde, Ciano, Roxo, Cinza, Vermelho, Amarelo e Azul, apresentaram comportamentos distintos quanto aos parâmetros microbiológicos e físico-químicos. Após este monitoramento, de acordo com valores referência adotados, e levando-se em conta como principais parâmetros classificatórios concentrações de BRS, bactérias anaeróbias totais e sulfeto, os dois tanques considerados mais limpos do monitoramento foram os tanques roxo e ciano. Analogamente, por apresentarem os piores desempenhos frente aos três principais parâmetros, os tanques amarelo e cinza foram considerados os mais sujos de todo o monitoramento. Após esta segregação, esses três principais parâmetros, mais a concentração de sulfato, foram inter-relacionados a fim de se corroborar esta classificação. Foi possível observar que o sulfeto instantâneo não foi o parâmetro mais adequado para se avaliar o potencial metabólico de uma amostra. Por este motivo, foram verificados os perfis metabólicos das BRS presentes nas amostras, confirmando a segregação dos tanques, baseada em parâmetros em batelada

光纤光栅在金属锈蚀传感中的应用

介绍了一种基于光纤布拉格光栅（FBG）应变敏感特性的金属锈蚀传感器。该器件由光纤光栅、有预应力的钢弹簧和一些机械部件组合而成。组合后的弹簧处于压缩状态。在弹簧弹力的作用下，光纤光栅的峰值波长增长了3．213m。对该器件进行了加速腐蚀实验：将其放入盐酸环境中，逐日监测光纤光栅峰值波长的变化，发现峰值波长逐渐缩短，说明弹簧的弹性系数随着弹簧的锈蚀而逐渐减小。到弹簧锈蚀断裂，整个锈蚀过程持续了1315h，平均锈蚀速率约5μm／d。实验表明了该传感器在实际应用中的可能性。同时讨论了光纤光栅的温度效应及其他影响其实

Tecnologia mais limpa aplicada ao tratamento de água em sistemas de resfriamento abertos com recirculação

Os estudos destinados à aplicação de uma tecnologia mais limpa ao tratamento de águas em sistemas de resfriamento abertos com recirculação resultaram no desenvolvimento de uma filosofia de tratamento baseada na busca de uma operação com ciclo de concentração ideal. Assim, por meio do controle do balanço material no sistema de resfriamento, seria alcançado um nível de concentração em que a água de circulação apresentaria, naturalmente e ao mesmo tempo, baixa tendência à corrosão do ferro e baixa tendência à formação de incrustação de carbonato de cálcio. O tratamento com inibidores de corrosão e de formação de depósitos seria apenas complementar e, conseqüentemente, reduzido o emprego de produtos químicos para o condicionamento da água. O presente trabalho procura demonstrar que o critério de tratamento baseado apenas no índice de estabilidade não leva em conta o fato de que as espécies solúveis em água não se concentram de uma mesma forma, principalmente como decorrência de reações de conversão envolvendo o íon bicarbonato e de precipitação do íon cálcio. Como suporte desse trabalho, foram realizados ensaios de campo em um sistema de resfriamento aberto com recirculação em operação normal, porém sem tratamento químico da água. Foi possível, desse modo, observar a variação da concentração de cada espécie crítica presente na água com a vazão de descarga efetuada. Os resultados obtidos e o estudo realizado mostram que a metodologia tradicional pode apresentar desvios da realidade que podem comprometer a qualidade do tratamento, obrigando o emprego de maiores concentrações de produtos químicos para condicionamento da água, contrariando, assim, o próprio propósito original de execução de um tratamento dentro dos princípios de uma produção mais limpa. Este trabalho procura, ainda, salientar a importância qualitativa e quantitativa das espécies presentes, na água de reposição, na qualidade do tratamento, alertando que o emprego de reúso de água, como reposição de um sistema de resfriamento, deve ser criteriosamente analisado, pois uma água de má qualidade pode tornar o tratamento interno impraticável, exigindo a execução de um tratamento prévio muitas vezes inviável do ponto de vista econômico e causador de impacto ambiental

Quantum Mechanics Studies of Fuel Cell Catalysts and Proton Conducting Ceramics with Validation by Experiment

We carried out quantum mechanics (QM) studies aimed at improving the performance of hydrogen fuel cells. This led to predictions of improved materials, some of which were subsequently validated with experiments by our collaborators.

In part I, the challenge was to find a replacement for the Pt cathode that would lead to improved performance for the Oxygen Reduction Reaction (ORR) while remaining stable under operational conditions and decreasing cost. Our design strategy was to find an alloy with composition Pt3M that would lead to surface segregation such that the top layer would be pure Pt, with the second and subsequent layers richer in M. Under operating conditions we expect the surface to have significant O and/or OH chemisorbed on the surface, and hence we searched for M that would remain segregated under these conditions. Using QM we examined surface segregation for 28 Pt₃M alloys, where M is a transition metal. We found that only Pt₃Os and Pt₃Ir showed significant surface segregation when O and OH are chemisorbed on the catalyst surfaces. This result indicates that Pt₃Os and Pt3Ir favor formation of a Pt-skin surface layer structure that would resist the acidic electrolyte corrosion during fuel cell operation environments. We chose to focus on Os because the phase diagram for Pt-Ir indicated that Pt-Ir could not form a homogeneous alloy at lower temperature. To determine the performance for ORR, we used QM to examine all intermediates, reaction pathways, and reaction barriers involved in the processes for which protons from the anode reactions react with O₂ to form H₂O. These QM calculations used our Poisson-Boltzmann implicit solvation model include the effects of the solvent (water with dielectric constant 78 with pH 7 at 298K). We found that the rate determination step (RDS) was the O_ad hydration reaction (O_ad + H₂O_ad -> OH_ad + OH_ad) in both cases, but that the barrier for pure Pt of 0.50 eV is reduced to 0.48 eV for Pt₃Os, which at 80 degrees C would increase the rate by 218%. We collaborated with the Pu-Wei Wu’s group to carry out experiments, where we found that the dealloying process-treated Pt2Os catalyst showed two-fold higher activity at 25 degrees C than pure Pt and that the alloy had 272% improved stability, validating our theoretical predictions.

We also carried out similar QM studies followed by experimental validation for the Os/Pt core-shell catalyst fabricated by the underpotential deposition (UPD) method. The QM results indicated that the RDS for ORR is a compromise between the OOH formation step (0.37 eV for Pt, 0.23 eV for Pt_2ML/Os core-shell) and H₂O formation steps (0.32 eV for Pt, 0.22 eV for Pt_2ML/Os core-shell). We found that Pt_2ML/Os has the highest activity (compared to pure Pt and to the Pt₃Os alloy) because the 0.37 eV barrier decreases to 0.23 eV. To understand what aspects of the core shell structure lead to this improved performance, we considered the effect on ORR of compressing the alloy slab to the dimensions of pure Pt. However this had little effect, with the same RDS barrier 0.37 eV. This shows that the ligand effect (the electronic structure modification resulting from the Os substrate) plays a more important role than the strain effect, and is responsible for the improved activity of the core- shell catalyst. Experimental materials characterization proves the core-shell feature of our catalyst. The electrochemical experiment for Pt_2ML/Os/C showed 3.5 to 5 times better ORR activity at 0.9V (vs. NHE) in 0.1M HClO₄ solution at 25 degrees C as compared to those of commercially available Pt/C. The excellent correlation between experimental half potential and the OH binding energies and RDS barriers validate the feasibility of predicting catalyst activity using QM calculation and a simple Langmuir–Hinshelwood model.

In part II, we used QM calculations to study methane stream reforming on a Ni-alloy catalyst surfaces for solid oxide fuel cell (SOFC) application. SOFC has wide fuel adaptability but the coking and sulfur poisoning will reduce its stability. Experimental results suggested that the Ni4Fe alloy improves both its activity and stability compared to pure Ni. To understand the atomistic origin of this, we carried out QM calculations on surface segregation and found that the most stable configuration for Ni₄Fe has a Fe atom distribution of (0%, 50%, 25%, 25%, 0%) starting at the bottom layer. We calculated that the binding of C atoms on the Ni4Fe surface is 142.9 Kcal/mol, which is about 10 Kcal/mol weaker compared to the pure Ni surface. This weaker C binding energy is expected to make coke formation less favorable, explaining why Ni₄Fe has better coking resistance. This result confirms the experimental observation. The reaction energy barriers for CHx decomposition and C binding on various alloy surface, Ni₄X (X=Fe, Co, Mn, and Mo), showed Ni₄Fe, Ni₄Co, and Fe₄Mn all have better coking resistance than pure Ni, but that only Ni₄Fe and Fe₄Mn have (slightly) improved activity compared to pure Ni.

In part III, we used QM to examine the proton transport in doped perovskite-ceramics. Here we used a 2x2x2 supercell of perovskite with composition Ba₈X₇M₁(OH)₁O₂₃ where X=Ce or Zr and M=Y, Gd, or Dy. Thus in each case a 4⁺ X is replace by a 3⁺ M plus a proton on one O. Here we predicted the barriers for proton diffusion allowing both includes intra-octahedron and inter-octahedra proton transfer. Without any restriction, we only observed the inter-octahedra proton transfer with similar energy barrier as previous computational work but 0.2 eV higher than experimental result for Y doped zirconate. For one restriction in our calculations is that the O_donor-O_acceptor atoms were kept at fixed distances, we found that the barrier difference between cerates/zirconates with various dopants are only 0.02~0.03 eV. To fully address performance one would need to examine proton transfer at grain boundaries, which will require larger scale ReaxFF reactive dynamics for systems with millions of atoms. The QM calculations used here will be used to train the ReaxFF force field.