Instabilities in two-liquid layers subject to a horizontal temperature gradient

We study theoretically the stability of two superposed fluid layers heated laterally. The fluids are supposed to be immiscible, the interface undeformable and of infinite horizontal extension. Combined thermocapillary and buoyancy forces give rise to a basic flow when a temperature difference is applied. The calculations are performed for a melt of GaAs under a layer of molten B2 O3 , a configuration of considerable technological importance. Four dif- ferent flow patterns and five temperature configurations are found for the basic state in this system. A linear stability analysis shows that the basic state may be destabilized by oscilla- tory motions leading to the so-called hydrothermal waves. Depending on the relative height of the two layers these hydrothermal waves propagate parallel or perpendicular to the temperature gradient. This analysis reveals that these perturbations can alter significantly the liquid flow in the liquid-encapsulated crystal growth techniques.

Convective instabilities in two superposed horizontal liquid layers heated laterally.

This work is devoted to the theoretical study of the stability of two superposed horizontal liquid layers bounded by two solid planes and subjected to a horizontal temperature gradient. The liquids are supposed to be immiscible with a nondeformable interface. The forces acting on the system are buoyancy and interfacial tension. Four different flow patterns and temperature profiles are found for the basic state. A linear perturbative analysis with respect to two- and three-dimensional perturbations reveals the existence of three kinds of patterns. Depending on the relative height of both liquids several situations are predicted: either wave propa- gation from cold to the hot regions, or waves propagating in the opposite direction or still stationary longitu- dinal rolls. The behavior of three different pairs of liquids which have been used in experiments on bilayers under vertical gradient by other authors have been examined. The instability mechanisms are discussed and a qualitative interpretation of the different behaviors exhibited by the system is provided. In some configurations it is possible to find a codimension-two point created by the interaction of two Hopf modes with different frequencies and wave numbers. These results suggest to consider two liquid layers as an interesting prototype ? nard-Marangoni problem.

Spatial Estimation of Sub-Hour Global Horizontal Irradiance Based on Official Observations and Remote Sensors.

This study was motivated by the need to improve densification of Global Horizontal Irradiance (GHI) observations, increasing the number of surface weather stations that observe it, using sensors with a sub-hour periodicity and examining the methods of spatial GHI estimation (by interpolation) with that periodicity in other locations. The aim of the present research project is to analyze the goodness of 15-minute GHI spatial estimations for five methods in the territory of Spain (three geo-statistical interpolation methods, one deterministic method and the HelioSat2 method, which is based on satellite images). The research concludes that, when the work area has adequate station density, the best method for estimating GHI every 15 min is Regression Kriging interpolation using GHI estimated from satellite images as one of the input variables. On the contrary, when station density is low, the best method is estimating GHI directly from satellite images. A comparison between the GHI observed by volunteer stations and the estimation model applied concludes that 67% of the volunteer stations analyzed present values within the margin of error (average of +-2 standard deviations).

Horizontal to vertical spectral ratio measurements in Port-au-Prince (Haiti) area damaged by the 2010 Haiti earthquake

In order to evaluate ground shaking characteristics due to surface soil layers in the urban area of Port-au-Prince, short-period ambient noise observation has been performed approximately in a 500x500m grid. The HVSR method was applied to this set of 36 ambient noise measurement points to determine a distribution map of soil predominant periods. This map reveals a general increasing trend in the period values, from the Miocene conglomerates in the northern and southern parts of the town to the central and western zones formed of Pleistocene and Holocene alluvial deposits respectively, where the shallow geological materials that cover the basement increase in thickness. Shorter predominant periods (less than 0.3 s) were found in mountainous and neighbouring zones, where the thickness of sediments is smaller whereas longer periods (greater than 0.5 s) appear in Holocene alluvial fans, where the thickness of sediments is larger. The shallow shear-wave velocity structure have been estimated by means of inversion of Rayleigh wave dispersion data obtained from vertical-component array records of ambient noise. The measurements were carried out at one open space located in Holocene alluvial deposits, using 3 regular pentagonal arrays with 5, 10 and 20m respectively. Reliable dispersion curves were retrieved for frequencies between 4.0 and 14 Hz, with phase velocity values ranging from 420m/s down to 270 m/s. Finally, the average shear-wave velocity of the upper 30 m (VS30) was inverted for characterization of this geological unit.

Horizontal visibility graphs generated by type-I intermittency

The type-I intermittency route to (or out of) chaos is investigated within the horizontal visibility (HV) graph theory. For that purpose, we address the trajectories generated by unimodal maps close to an inverse tangent bifurcation and construct their associatedHVgraphs.We showhowthe alternation of laminar episodes and chaotic bursts imprints a fingerprint in the resulting graph structure. Accordingly, we derive a phenomenological theory that predicts quantitative values for several network parameters. In particular, we predict that the characteristic power-law scaling of the mean length of laminar trend sizes is fully inherited by the variance of the graph degree distribution, in good agreement with the numerics. We also report numerical evidence on how the characteristic power-law scaling of the Lyapunov exponent as a function of the distance to the tangent bifurcation is inherited in the graph by an analogous scaling of block entropy functionals defined on the graph. Furthermore, we are able to recast the full set of HV graphs generated by intermittent dynamics into a renormalization-group framework, where the fixed points of its graph-theoretical renormalization-group flow account for the different types of dynamics.We also establish that the nontrivial fixed point of this flow coincides with the tangency condition and that the corresponding invariant graph exhibits extremal entropic properties.

New designs of the ceramic bricks of horizontal hexagonal hollow

This article is intended to state that Technical Drawing is a multiple tool of expression and communication essential to develop inquiry processes, the scientifically basis and comprehension of drawings and technological designs that can be manufactured. We demonstrate graphically and analytically that spatial vision and graphic thinking allow us to identify graphically real life problems, develop proposals of solutions to be analysed from different points of view, plan and develop the project, provide information needed to make decisions on objects and technological processes. From the knowledge of Technical Drawing and CAD tools we have developed graphic analyses to improve and optimize our proposed modification of the geometry of the rectangular cells of conventional bricks by hexagonal cells, which is protected by a Spanish patent owned by the Polytechnic University of Madrid. This new internal geometry of the bricks will improve the efficiency and the acoustic damping of walls built with the ceramic bricks of horizontal hollow, maintaining the same size of the conventional bricks, without increasing costs either in the manufacture and the sale. A single brick will achieve the width equivalent to more than FOUR conventional bricks.

Origin of the gases released from the Acqua Passante and Ermeta wells (Mt. Amiata, central Italy) and possible environmental implications for their closure

The Mt. Amiata volcano (Tuscany, central Italy) hosts the second largest geothermal field of Italy. Its SW and NE sectors are characterized by the presence of several CO2-rich (mayor que95% by vol.) gas discharges. An intense Hg mining activity had taken place from the 19th century up to the end of the ?70s, particularly close to Abbadia San Salvatore, during which two drillings (Acqua Passante and Ermeta) intercepted a CO2-rich gas fertile horizon. The related gases are emitted in the atmosphere since 1938 and 1959, respectively, causing severe concerns for the local air quality. In this work the results of a geochemical and isotopic survey carried out on these gas emissions from March 2009 to January 2014 are presented. CO2 fluxes from both the two wells and soil from an area of about 653,500 m2 located between them were measured. The two wells are emitting up to 15,000, 92 and 8 tons y-1 of CO2, CH4 and H2S, respectively, while the computed soil CO2 output was estimated at 4,311 ton y-1. The spatial distribution of the CO2 soil flux suggests the presence of preferential patterns, indicating sites of higher permeability. Since the local municipality is evaluating the possibility to plug the Ermeta vent, a temporarily closure should first be carried out to test the possible influence of this operation on the diffuse soil degassing of deep-originated CO2 in the surrounding area. This implies that diffuse soil gases should carefully be monitored before proceeding with its definitive closure.

Efecto del tamaño de la ventana de promediado y la histéresis variable en algoritmos de handover horizontal en redes convergentes

En las redes convergentes inalámbricas, el traspaso horizontal entre distintos puntos de acceso de la red WLAN es una gran fuente de degradación de la calidad de la VoIP y otros servicios conversacionales en tiempo real. Esto es debido a que este tipo de redes no fueron concebidas originalmente para soportar este tipo de servicios, y los traspasos siguen un protocolo ¿cortar antes de realizar¿, produciéndose interrupciones en la comunicación motivadas por el tiempo que necesitan los terminales en volver a asociarse a la red. En este artículo se estudia el efecto que tienen el tamaño de la ventana de promediado de la señal, la histéresis variable y el retardo del handover por parecido entre potencia de puntos de acceso de destino sobre el número de traspasos y las caídas de la potencia de señal por debajo del valor de sensibilidad del terminal, causantes principales de las interrupciones en la comunicación, y, con ello, de la degradación de la calidad de las comunicaciones.

Plano Horizontal Plano. Del plano horizontal como límite entre lo estereotómico y lo tectónico = Flat Horizontal Plane. On Horizon

Plano Horizontal Plano. Del plano horizontal como límite entre lo estereotómico y lo tectónico

Flat Horizontal Plane - On Horizon

The Flat Horizontal Plane, the platform, is more than just one of the most basic mechanisms of Architecture. In this essay, I would like to move towards understanding this Flat Horizontal Plane not only as the primary mechanism of Architecture, but also, when it is erected, as the spatial limit between the stereotomic and the tectonic.

Differences brick facade design to horizontal loads between the Spanish and European standards

Brick facades are a construction type, strongly linked to local construction characteristics and methods. In Spain, particularly in Castilla, the facades have been built since the '80s with Castilian half foot (11.5 cm), resting on the edge of slabs. The design of these facades, to horizontal loads from wind, depending on the codes used, can lead to completely different valid solutions. Applying same loads, the facades studied with current European standard (Eurocode 6), have a maximum length of 7.1 m between supports, while the Spanish code, Technical Building Code - Structural Safety Masonry, (CTE SE-F), 8.4 m can be achieved. This represents an increase of flexural strength, depending on the calculation model used, which can reach until 8 times. This is due to the difference of the calculation method and the structural model in one and another standard, depending on if this facade is analyzed as a vertical or horizontal beam or by formation of a vertical or horizontal archh. This paper analyzes the constructive solution of the brick facades that results from applying Spanish or European standards and how it affects the model applied in the safety of the resulting facade.

Análisis de la resistencia de las juntas frente a carga horizontal de un edificio de dos plantas construido con paneles prefabricados de hormigón armado

En el presente estudio se pretende abordar la situación de estudio en la que actualmente se encuentra el estudio y análisis del comportamiento de juntas de hormigón a esfuerzo rasante pero sin armadura pasante concretamente en este trabajo realizado se ha procedido analizar el comportamiento de paneles para la empresa INDAGSA que ha desarrollado unos paneles prefabricados portantes que sus juntas se componen de una barra corrugada embebida a lo largo de la junta en el hormigón ejecutado in situ. El estudio será enfocado desde un punto de vista específico para los paneles que desarrolla el grupo INDAGSA ya que posteriormente se realizaran ensayos en laboratorio de paneles prefabricados para comparar su comportamiento con los modelos analizados en este trabajo, aunque la aplicación que se explica esta principalmente como indica la actual normativa se trata como una junta entre hormigones de distinta edad concretamente uno prefabricado y el otro perteneciente a la junta ejecutado in situ. El análisis del comportamiento a esfuerzo rasante de juntas de hormigón sin armadura pasante se ha abordado escasas veces por lo que tampoco existen muchos estudios en los que basarse y más en elementos tan esbeltos como son los paneles prefabricados que se han analizado de 10 cm de espesor, 2,2 m de altura y un vano de 6,4 m. Los paneles se analizaran mediante el software de cálculo estructural Sap2000 mediante modelado y análisis con elementos finitos. Después de modelar los paneles sencillos es decir que no forman parte de ninguna estructura sino que se analizaran como viga biapoyada, modelada la junta con elementos muelle o muelles verificando que se aproximan a los valores teóricos obtenidos de tensión en el acero y esfuerzo rasante generado en la junta. Una vez modelados y verificados se usaran los parámetros de los paneles sencillos para modelar una vivienda de dos plantas y se analizara su comportamiento a carga horizontal estudiando la forma por la que puede fallar la vivienda si es a causa de la rotura por esfuerzo rasante de las juntas o por plastificación de la armadura anclada en la cimentación. Posteriormente con estos resultados obtenidos INDAGSA tiene el prototipo de vivienda en escala real para someterlo a un ensayo a carga horizontal como el simulado y analizado con Sap2000 para comprobar y ajustar el modelo.

Determinación paramétrica para el análisis de la viabilidad técnico económica de la implantación de un parque de aprovechamiento energético de corrientes marinas mediante un generador en inmersión con rotor de eje horizontal

La presente Tesis se ha centrado en un análisis de la tecnología para la generación de energía eléctrica utilizando las corrientes marinas. El contenido desarrollado ha consistido en un análisis de las distintas alternativas para poder aprovechar la energía oceánica con especial interés en los desarrollos tecnológicos de las corrientes marinas. Posteriormente se ha descrito un nuevo prototipo, basado en un diseño de un generador en inmersión con rotor de eje horizontal con estructura en Y, denominado proyecto GESMEY. Se han analizado diversas localizaciones para poder implantar un prototipo experimental del proyecto GESMEY, así como las posibles localizaciones para implementar un parque de explotación comercial basado en esta tecnología, llegando a conclusiones importantes referidas a la costa española, y definiendo localizaciones muy interesantes en la costa Escocesa. Finalmente se han analizado diversos parámetros de definición de estos parques de aprovechamiento de la energía, clasificándolos como parámetros técnicos, de ubicación, de utilización, medioambientales y económicos. A la vista de la investigación realizada se ha concluido que hay muchas líneas de investigación que desarrollar, y que desde un punto de vista estratégico hay muchas actuaciones que poner en marcha para potenciar la tecnología de las energías renovables marinas mediante corrientes marinas. ABSTRACT This thesis has focused on an analysis of technology for generating electrical power using ocean currents. The content developed consisted of an analysis of the alternatives to take advantage of ocean energy with special emphasis on the technological developments of ocean currents. Subsequently it described a new prototype, based on a design of a generator rotor immersion horizontal axis Y structure, called GESMEY project. We analyzed different locations to implement an experimental prototype GESMEY project and possible locations to deploy a fleet of commercial exploitation based on this technology, reaching important conclusions regarding the Spanish coast, and defining interesting locations on the coast Scottish. Finally, we have analyzed various parameters defining these parks use of energy, classifying them as technical parameters, location, utilization, environmental and economic. In view of the conducted research has concluded that there are many lines of research to develop, and that from a strategic point of view there are many actions to implement to enhance the technology of marine renewable energies by sea currents.

Campos de juego de Noguchi y Van Eyck. El plano horizontal

Campos de juego de Noguchi y Van Eyck. El plano horizontal

1952 Barbara Jo Wells

1952-1953 Miss Homecoming