Tin oxide based composites derived using electrostatic spray deposition technique as anodes for lithium-ion batteries

Recent advances in the electric & hybrid electric vehicles and rapid developments in the electronic devices have increased the demand for high power and high energy density lithium ion batteries. Graphite (theoretical specific capacity: 372 mAh/g) used in commercial anodes cannot meet these demands. Amorphous SnO2 anodes (theoretical specific capacity: 781 mAh/g) have been proposed as alternative anode materials. But these materials have poor conductivity, undergo a large volume change during charging and discharging, large irreversible capacity loss leading to poor cycle performances. To solve the issues related to SnO2 anodes, we propose to synthesize porous SnO2 composites using electrostatic spray deposition technique. First, porous SnO2/CNT composites were fabricated and the effects of the deposition temperature (200, 250, 300 °C) & CNT content (10, 20, 30, 40 wt %) on the electrochemical performance of the anodes were studied. Compared to pure SnO2 and pure CNT, the composite materials as anodes showed better discharge capacity and cyclability. 30 wt% CNT content and 250 °C deposition temperature were found to be the optimal conditions with regard to energy capacity whereas the sample with 20% CNT deposited at 250 °C exhibited good capacity retention. This can be ascribed to the porous nature of the anodes and the improvement in the conductivity by the addition of CNT. Electrochemical impedance spectroscopy studies were carried out to study in detail the change in the surface film resistance with cycling. By fitting EIS data to an equivalent circuit model, the values of the circuit components, which represent surface film resistance, were obtained. The higher the CNT content in the composite, lower the change in surface film resistance at certain voltage upon cycling. The surface resistance increased with the depth of discharge and decreased slightly at fully lithiated state. Graphene was also added to improve the performance of pure SnO2 anodes. The composites heated at 280 °C showed better energy capacity and energy density. The specific capacities of as deposited and post heat-treated samples were 534 and 737 mAh/g after 70 cycles. At the 70th cycle, the energy density of the composites at 195 °C and 280 °C were 1240 and 1760 Wh/kg, respectively, which are much higher than the commercially used graphite electrodes (37.2–74.4 Wh/kg). Both SnO2/CNTand SnO2/grapheme based composites with improved energy densities and capacities than pure SnO2 can make a significant impact on the development of new batteries for electric vehicles and portable electronics applications.

An experimental study of micro-end-milling operations

Cutting tools less than 2mm diameter can be considered as micro-tool. Microtools are used in variety of applications where precision and accuracy are indispensable. In micro-machining operations, a small amount of material is removed and very small cutting forces are created. The small cross sectional area of the micro-tools drastically reduces their strength and makes their useful life short and unpredictable; so cutting parameters should be selected carefully to avoid premature tool breakage. The main objective of this study is to develop new techniques to select the optimal cutting conditions with minimum number of experiments and to evaluate the tool wear in machining operations. Several experimental setups were prepared and used to investigate the characteristics of cutting force and AE signals during the micro-end-milling of different materials including steel, aluminum and graphite electrodes. The proposed optimal cutting condition selection method required fewer experiments than conventional approaches and avoided premature tool breakage. The developed tool wear monitoring technique estimated the used tool life with ±10% accuracy from the machining data collected during the end-milling of non-metal materials.

AFM and SPR studies of protein adsorption at solid/liquid interface

Membrane-like structure formed by surfactant molecules of didodecyldimethylammonium bromide (DDAB) on both HOPG and gold electrodes were studied with AFM and SPR techniques. The study shows that the thickness of the adsorbed layer of DDAB is strongly dependent on the concentration of the vesicle solution. We have also investigated the adsorption of redox protein, Cytochrome c, on graphite electrode with in situ tapping mode AFM. The protein adsorbs spontaneously onto the electrode covered with an adsorbed phosphate layer and forms a uniform monolayer. The adsorbed protein exhibits a reversible electron transfer at 0.17 V (Ag/AgCI) once the electrode potential has been increased to 0.75V. Using surface plasmon resonance spectroscopy we have measured subtle conformational change in protein, Cyt c, due to electron transfer of a single electron on MPA-coated gold electrode. The electron transfer induced change in the resonant angle is about 0.006 deg., which corresponds to ~ 0.2 A decreases in the thickness. This is consistent with that reduced state is more compact than the oxidized state.

Determinação de CD, PB, e TL em água produzida por HR-CS GF AAS após extração em ponto nuvem

Produced water is a major problem associated with the crude oil extraction activity. The monitoring of the levels of metals in the waste is constant and requires the use of sensitive analytical techniques. However, the determination of trace elements can often require a pre-concentration step. The objective of this study was to develop a simple and rapid analytical method for the extraction and pre-concentration based on extraction phenomenon cloud point for the determination of Cd, Pb and Tl in produced water samples by spectrometry of high resolution Absorption source continues and atomization graphite furnace. The Box Behnken design was used to obtain the optimal condition of extraction of analytes. The factors were evaluated: concentration of complexing agent (o,o-dietilditilfosfato ammonium, DDTP), the concentration of hydrochloric acid and concentration of surfactant (Triton X -114). The optimal condition obtained through extraction was: 0,6% m v-1 DDTP, HCl 0,3 mol L-1 and 0,2% m v-1 of Triton X - 114 for Pb; 0,7% m v-1 DDTP, HCl 0,8 mol L-1 and 0,2% m v-1 Triton X-114 for Cd. For Tl was evidenced that best extraction condition occurs with no DDTP, the extraction conditions were HCl 1,0 mol L-1 e 1,0% m v-1 de Triton X - 114. The limits of detection for the proposed method were 0,005 µg L-1 , 0,03 µg L-1 and 0,09 µg L-1 to Cd, Pb and Tl, Respectively. Enrichment factors Were greater than 10 times. The method was applied to the water produced in the Potiguar basin, and addition and recovery tests were performed, and values were between 81% and 120%. The precision was expressed with relative standard deviation (RSD) is less than 5%

Desenvolvimento de metodologia de extração e pré-concentração utilizando sistema microemulsionado para determinação de Cd, Co, Cu, Ni, Pb e Tl em águas naturais e produzidas por HR-CS AAS

The determination and monitoring of metallic contaminants in water is a task that must be continuous, leading to the importance of the development, modification and optimization of analytical methodologies capab le of determining the various metal contaminants in natural environments, because, in many cases, the ava ilable instrumentation does not provide enough sensibility for the determination of trace values . In this study, a method of extraction and pre- concentration using a microemulsion system with in the Winsor II equilibrium was tested and optimized for the determination of Co, Cd, P b, Tl, Cu and Ni through the technique of high- resolution atomic absorption spectrometry using a continuum source (HR-CS AAS). The optimization of the temperature program for the graphite furnace (HR-CS AAS GF) was performed through the pyrolysis and atomization curves for the analytes Cd, Pb, Co and Tl with and without the use of different chemical modifiers. Cu and Ni we re analyzed by flame atomization (HR-CS F AAS) after pre-concentr ation, having the sample introduction system optimized for the realization of discrete sampling. Salinity and pH levels were also analyzed as influencing factors in the efficiency of the extraction. As final numbers, 6 g L -1 of Na (as NaCl) and 1% of HNO 3 (v/v) were defined. For the determination of the optimum extraction point, a centroid-simplex statistical plan was a pplied, having chosen as the optimum points of extraction for all of the analytes, the follo wing proportions: 70% aqueous phase, 10% oil phase and 20% co-surfactant/surfactant (C/S = 4). After extraction, the metals were determined and the merit figures obtained for the proposed method were: LOD 0,09, 0,01, 0,06, 0,05, 0,6 and 1,5 μg L -1 for Pb, Cd, Tl, Co, Cu and Ni, re spectively. Line ar ranges of ,1- 2,0 μg L -1 for Pb, 0,01-2,0 μg L -1 for Cd, 1,0 - 20 μg L -1 for Tl, 0,1-5,0 μg L -1 for Co, 2-200 μg L -1 and for Cu e Ni 5-200 μg L -1 were obtained. The enrichment factors obtained ranged between 6 and 19. Recovery testing with the certified sample show ed recovery values (n = 3, certified values) after extraction of 105 and 101, 100 and 104% for Pb, Cd, Cu and Ni respectively. Samples of sweet waters of lake Jiqui, saline water from Potengi river and water produced from the oil industry (PETROBRAS) were spiked and the recovery (n = 3) for the analytes were between 80 and 112% confirming th at the proposed method can be used in the extraction. The proposed method enabled the sepa ration of metals from complex matrices, and with good pre-concentration factor, consistent with the MPV (allowed limits) compared to CONAMA Resolution No. 357/2005 which regulat es the quality of fresh surface water, brackish and saline water in Brazil.

Aplicação e otimização de métodos eletroquímicos combinados para remoção e determinação de cromo hexavalente em efluentes simulados

Hexavalent chromium is a heavy metal present in various industrial effluents, and depending on its concentration may cause irreparable damage to the environment and to humans. Facing this surrounding context, this study aimed on the application of electrochemical methods to determine and remove the hexavalent chromium (Cr6+) in simulated wastewater. To determine was applied to cathodic stripping voltammetry (CSV) using ultra trace graphite electrodes ultra trace (work), Ag/AgCl (reference) and platinum (counter electrode), the samples were complexed with 1,5- diphenylcarbazide and then subjected to analysis. The removal of Cr6+ was applied electrocoagulation process (EC) using Fe and Al electrodes. The variables that constituted the factorial design 24, applied to optimizing the EC process, were: current density (5 and 10 mA.cm-2), temperature (25 and 60 ºC), concentration (50 and 100 ppm) and agitation rate (400 and 600 RPM). Through the preliminary test it was possible the adequacy of applying the CSV for determining of Cr6+, removed during the EC process. The Fe and Al electrodes as anodes sacrifice showed satisfactory results in the EC process, however Fe favored complete removal in 30 min, whereas with Al occurred at 240 min. In the application of factorial design 24 and analysis of Response Surface Methodology was possible to optimize the EC process for removal of Cr6+ in H2SO4 solution (0.5 mol.L-1), in which the temperature, with positive effect, was the variable that presented higher statistical significance compared with other variables and interactions, while in optimizing the EC process for removal of Cr6+ in NaCl solution (0.1 mol.L-1) the current density, with positive effect, and concentration, with a negative effect were the variables that had greater statistical significance with greater statistical significance compared with other variables and interactions. The utilization of electrolytes supports NaCl and Na2SO4 showed no significant differences, however NaCl resulted in rapid improvement in Cr6+ removal kinetics and increasing the NaCl concentration provided an increase in conductivity of the solution, resulting in lower energy consumption. The wear of the electrodes evaluated in all the process of EC showed that the Al in H2SO4 solution (0.5 mol.L-1), undergoes during the process of anodization CE, then the experimental mass loss is less than the theoretical mass loss, however, the Fe in the same medium showed a loss of mass greater experimental estimated theoretically. This fact is due to a spontaneous reaction of Fe with H2SO4, and when the reaction medium was the NaCl and Na2SO4 loss experimental mass approached the theoretical mass loss. Furthermore, it was observed the energy consumption of all processes involved in this study had a low operating cost, thus enabling the application of the EC process for treating industrial effluents. The results were satisfactory, it was achieved complete removal of Cr6+ in all processes used in this study.

Interrogazione visuale per basi di dati a grafo: il sistema GraphVista

Oggi l’esigenza di permettere all’utente di riuscire a formulare interrogazioni su database a grafo in maniera più semplice e soprattutto intuitiva ha portato gli istituti di ricerca a proporre metodi di interrogazione visuale. Uno dei sistemi che sono stati proposti è GraphVista. Tale sistema si basa sull’idea di dividere l’interrogazione in due macro-fasi. La prima fase permette di avvicinarsi al risultato richiesto escludendo da successive analisi dati che sicuramente non potranno far parte del risultato finale, mentre la seconda fase permette all’utente di essere protagonista. Infatti ad esso è concessa la possibilità di manipolare a proprio piacimento i risultati ottenuti dalla prima fase al fine di “ricercare” da sé le informazioni desiderate. Il tutto viene supportato grazie a un’interfaccia intuitiva ed efficace che permette all’utente di navigare interattivamente all’interno di una base di dati a grafo. Le caratteristiche dell’interfaccia e la possibilità di formulare interrogazioni visuali fanno in modo che l’utente non necessiti di conoscere alla perfezione un linguaggio di query specifico. Nel corso di questa tesi viene descritto il sistema GraphVista e la tecnologia sulla quale si fonda. Infine, viene effettuata una comparazione sull’efficacia e la semplicità d’uso del sistema GraphVista rispetto alla formulazione di query tramite un linguaggio standard come SPARQL.

Dissolved Zinc in the Southern Ocean measured on water bottle samples during POLARSTERN cruise ANT-XXIV/3

The distribution of dissolved zinc (Zn) was investigated in the Atlantic sector of the Southern Ocean in the austral autumn of 2008 as part of the IPY GEOTRACES expedition ZERO & DRAKE. Research focused on transects across the major frontal systems along the Zero Meridian and across the Drake Passage. There was a strong gradient in surface zinc concentrations observed across the Antarctic Polar Front along both transects and high zinc levels were found in surface waters throughout the Southern Ocean. Vertical profiles for dissolved Zinc showed the presence of local minima and maxima in the upper 200 m consistent with significant uptake by phytoplankton and release by zooplankton grazing, respectively. Highest deep water zinc concentrations were found in the centre of the Weddell Gyre associated with Central Intermediate Water (CIW), a water mass which is depleted in O2, elevated in CO2 and is regionally a CFC minimum. Our data suggests that the remineralization of sinking particles is a key control on the distribution of Zn in the Southern Ocean. Disappearance ratios of zinc to phosphate (Zn:P) in the upper water column increased southwards along both transects and based on laboratory studies they suggest slower growth rates of phytoplankton due to iron or light limitation. Zinc and silicate were strongly correlated throughout the study region but the disappearance ratio (Zn:Si) was relatively uniform overall except for the region close to the ice edge on the Zero Meridian.

Beryllium isotopes of sediments from the Portuguese margin

A high resolution study of authigenic Be isotopes (10Be and 9Be) combined with continuous relative paleointensity records has been performed along the same marine sedimentary sequences from the Portuguese margin (NE Atlantic) covering the past 300 kyr in order to assess relationships between geomagnetic moment variations and 10Be production rate variations. A careful examination of the various ways of taking into account environmental disturbing effects on the authigenic 10Be concentration leads to the conclusion that the most reliable proxy of cosmonuclide production rates is presently the authigenic 10Be/9Be ratio. Eight intervals of significant authigenic 10Be/9Be enhancement evidence geomagnetic moment drops related to global paleomagnetic excursions, some being already admitted, others being proposed as new geomagnetic features. Since, unlike sedimentary magnetic remanence, the authigenic 10Be/9Be records dipole moment variations without significant acquisition delay, it provides better constraints on their timing. Comparison of 10Be/9Be and benthic delta18O records from the same cores suggests that dipole moment lows preferentially occurred during or at the end of interglacial episodes, with a quasi-period of 100 kyr.

Paleomagnetic and beryllium isotope record of West Equatorial Pacific sediments

The reliability of paleomagnetic records as proxies of the geomagnetic field intensity is still a matter of controversy since volcanic materials hardly provide continuous records, and marine sediments are suspected to carry a remanence biased by post-depositional realignments and/or by overprints. Such long standing debate emphasizes the need for the development of methods independent from paleomagnetism to decipher geomagnetic intensity variations. High resolution measurements of authigenic 10Be/9Be along with a detailed sedimentary record of directional and relative paleointensity variations evidence, over the 0.6-1.3 Ma time interval, frequent and recurrent excursions or short events in the late Matuyama and the early Brunhes epochs, among which two Brunhes-Matuyama reversal precursors and an intra-Jaramillo excursion. The results of this study confirm the idea of a highly unstable geomagnetic field as suggested by paleomagnetic evidences.

Retificação plana tangencial dos ferros fundidos nodular, vermicular e cinzento em várias condições de corte

In a scenario of increasing competitiveness of the global industrial sector and with a consumer market increasingly demanding, there is an increased demand for new materials and, consequently, possibilities to explore new research and technological advances towards the development of new manufacturing methods or the improvement of existing technologies. In the case of cast irons, new grades of them have been developed so that their mechanical properties have been improved, making them more competitive with steel, expanding the applications and thus represents great economic gain for metallurgy and manufacturing sectors. This increases the interest and creates new opportunities to study these materials and identify how they respond in terms of the surface integrity, tool wear, cutting forces, among others, when machined by grinding operation. In this context, due to the lack of results from grinding of cast irons and studies comparing grindability among several grades of cast irons found in the literature, this work aims to generate scientific and technological contribution to the metallurgical and metal working sector through roughness results (Ra and Rz parameters) and evaluation and analysis of the subsurface integrity of three cast iron grades (gray, compacted graphite and nodular). The machining trials were performed on a surface grinding machine with silicon carbide grinding wheel at different cutting conditions. The input variables were the radial depth of cut (15 and 30 μm), worktable speed, vw (5 and 10 m/min) and the abrasive grain size of the grinding wheel. The results showed that surface roughness increased with the radial depth of cut for all materials tested; and the lowest values were obtained for gray cast iron. Also, roughness was sensitive to variation of worktable speed and the lowest values were obtained after machining with vw = 5 m/min. With respect to the abrasive grain size, as it decreased the roughness values increased to gray and nodular cast iron grades. Furthermore, grinding burns marks were observed on the surfaces of nodular cast iron and compacted graphite iron grades after grinding the smallest grain size, contrary to what is usually reported in literature. However, no evidence of severe thermal damages below the machined surfaces of all cast iron grades was observed after analyzing the results of hardness and the SEM micrograph images.

Layered graphitic carbon host formation during liquid-free solid state growth of metal pyrophosphates

We report a successful ligand- and liquid-free solid state route to form metal pyrophosphates within a layered graphitic carbon matrix through a single step approach involving pyrolysis of previously synthesized organometallic derivatives of a cyclotriphosphazene. In this case, we show how single crystal Mn2P2O7 can be formed on either the micro- or the nanoscale in the complete absence of solvents or solutions by an efficient combustion process using rationally designed macromolecular trimer precursors, and present evidence and a mechanism for layered graphite host formation. Using in situ Raman spectroscopy, infrared spectroscopy, X-ray diffraction, high resolution electron microscopy, thermogravimetric and differential scanning calorimetric analysis, and near-edge X-ray absorption fine structure examination, we monitor the formation process of a layered, graphitic carbon in the matrix. The identification of thermally and electrically conductive graphitic carbon host formation is important for the further development of this general ligand-free synthetic approach for inorganic nanocrystal growth in the solid state, and can be extended to form a range of transition metals pyrophosphates. For important energy storage applications, the method gives the ability to form oxide and (pyro)phosphates within a conductive, intercalation possible, graphitic carbon as host–guest composites directly on substrates for high rate Li-ion battery and emerging alternative positive electrode materials

(Table 2) Concentration of heavy metals and organic carbon, and 210Pb activity of sediments near Büsum, eastern Wadden Sea

A 3.38 m long sediment core raised from the tidal flat sediments of the 'Blauortsand' in the Wadden Sea northwest of Büsum (Schleswig-Holstein, Germany) was analysed in order to investigate long term changes in sediment pollution with Pb, Cu, Zn and Cd. Comparison with the topographic maps since 1952 and 210Pb activity allowed a general dating of the sediment succession in the core. The heavy metal concentrations including 210Pb of the < 20 µm grain-size fraction in thick sediment slices below 1.30 m indicated background niveaus. Their values increased and reached modern levels in the upper sediment layers of the core above 1 m. The increments for Pb, Cu, Zn was 1 to 3 fold and Cd up to 11 fold since the second half of the 19th century. More investigations are needed to quantify the geographical extent and history of the contaminations shown in this pilot study.

Composition of bottom sediments and interstitial waters from the Gdansk Bay

Contents of mercury and zinc in reduced sediments and interstitial waters of the Gdansk Bay in the Baltic Sea were investigated. It was found that sediments contain 0.7 ppm Hg, of which 0.008 ppm.(0.4% of total) is dissolved in interstitial water, and 91 ppm Zn, of which 0.15 ppm (0.45% of total) is dissolved in interstitial water. Differences in contents in different layers (0-5 and 25-30 cm) can be attributed to anthropogenic influence. Aderage concentration of mercury in the upper sediment layer is 27% higher and one of zinc is 40% higher than those found in the lower sediment layer. In addition, distribution of zinc in grain size fractions of the sediments was investigated, and some data on cadmium content were obtained.