Antagonism of the two-needle pine stem rust fungi Cronartium flaccidum and Peridermium pini by Cladosporium tenuissimum in vitro and in planta

Selected isolates of Cladosporium tenuissimum were tested for their ability to inhibit in vitro aeciospore germination of the two-needle pine stem rusts Cronartium flaccidum and Peridermium pini and to suppress disease development in planta. The antagonistic fungus displayed a number of disease-suppressive mechanisms. Aeciospore germination on water agar slides was reduced at 12, 18, and 24 h when a conidial suspension (1.5 x 10(7) conidia per ml) of the Cladosporium tenuissimum isolates was added. When the aeciospores were incubated in same-strength conidial suspensions for 1, 11, 21, and 31 days, viability was reduced at 20 and 4 degreesC. Light and scanning electron microscopy showed that rust spores were directly parasitized by Cladosporium tenuissimum and that the antagonist had evolved several strategies to breach the spore wail and gain access to the underlying tissues. Penetration occurred with or without appressoria. The hyperparasite exerted a mechanical force to destroy the spore structures (spinules, cell wall) by direct contact, penetrated the aeciospores and subsequently proliferated within them. However, an enzymatic action could also be involved. This was shown by the dissolution of the host tell wall that comes in contact with the mycelium of the mycoparasite, by the lack of indentation in the host wall at the contact site, and by the minimal swelling at the infecting hyphal tip. Culture filtrates of the hyperparasite inhibited germination of rust propagules. A compound purified from the filtrates was characterized by chemical and spectroscopic analysis as cladosporol, a known beta -1,3-glucan biosynthesis inhibitor. Conidia of Cladosporium tenuissimum reduced rust development on new infected pine seedlings over 2 years under greenhouse conditions. Because the fungus is an aggressive mycoparasite, produces fungicidal metabolites, and can survive and multiply in forest ecosystems without rusts, it seems a promising agent for the biological control of pine stem rusts in Europe.

Mathematical methods for spatially cohesive reserve design

The problem of designing spatially cohesive nature reserve systems that meet biodiversity objectives is formulated as a nonlinear integer programming problem. The multiobjective function minimises a combination of boundary length, area and failed representation of the biological attributes we are trying to conserve. The task is to reserve a subset of sites that best meet this objective. We use data on the distribution of habitats in the Northern Territory, Australia, to show how simulated annealing and a greedy heuristic algorithm can be used to generate good solutions to such large reserve design problems, and to compare the effectiveness of these methods.

Local complexity of Delone sets and crystallinity

This paper characterizes when a Delone set X in R-n is an ideal crystal in terms of restrictions on the number of its local patches of a given size or on the heterogeneity of their distribution. For a Delone set X, let N-X (T) count the number of translation-inequivalent patches of radius T in X and let M-X (T) be the minimum radius such that every closed ball of radius M-X(T) contains the center of a patch of every one of these kinds. We show that for each of these functions there is a gap in the spectrum of possible growth rates between being bounded and having linear growth, and that having sufficiently slow linear growth is equivalent to X being an ideal crystal. Explicitly, for N-X (T), if R is the covering radius of X then either N-X (T) is bounded or N-X (T) greater than or equal to T/2R for all T > 0. The constant 1/2R in this bound is best possible in all dimensions. For M-X(T), either M-X(T) is bounded or M-X(T) greater than or equal to T/3 for all T > 0. Examples show that the constant 1/3 in this bound cannot be replaced by any number exceeding 1/2. We also show that every aperiodic Delone set X has M-X(T) greater than or equal to c(n)T for all T > 0, for a certain constant c(n) which depends on the dimension n of X and is > 1/3 when n > 1.

Who does not gain weight? Prevalence and predictors of weight maintenance in young women

OBJECTIVE: To investigate the prevalence and predictors of weight maintenance over time in a large sample of young Australian women. DESIGN: This population study examined baseline and 4y follow-up data from the cohort of young women participating in the Australian Longitudinal Study on Women's Health. SUBJECTS: A total of 8726 young women aged 18 - 23y at baseline. MEASURES: Height, weight and body mass index (BMI); physical activity; time spent sitting; selected eating behaviours (eg dieting, disordered eating, takeaway food consumption); cigarette smoking, alcohol consumption; parity; and socio-demographic characteristics. RESULTS: Only 44% of the women reported their BMI at follow-up to be within 5% of their baseline BMI (maintainers); 41% had gained weight and 15% had lost weight. Weight maintainers were more likely to be in managerial or professional occupations; to have never married; to be currently studying; and not to be mothers. Controlling for sociodemographic factors, weight maintainers were more likely to be in a healthy weight range at baseline, and to report that they spent less time sitting, and consumed less takeaway food, than women who gained weight. CONCLUSIONS: Fewer than half the young women in this community sample maintained their weight over this 4y period in their early twenties. Findings of widespread weight gain, particularly among those already overweight, suggest that early adulthood, which is a time of significant life changes for many women, may be an important time for implementing strategies to promote maintenance of healthy weight. Strategies which encourage decreased sitting time and less takeaway food consumption may be effective for encouraging weight maintenance at this life stage.

Which aspects of socio-economic status are related to health in mid-aged and older women?

A population-based study was conducted to validate gender- and age-specific indexes of socio-economic status (SES) and to investigate the associations between these indexes and a range of health outcomes in 2 age cohorts of women. Data from 11,637 women aged 45 to 50 and 9,5 10 women aged 70 to 75 were analyzed. Confirmatory factor analysis produced four domains of SES among the mid-aged cohort (employment, family unit, education, and migration) and four domains among the older cohort (family unit, income, education, and migration). Overall, the results supported the factor structures derived from another population-based study (Australian Bureau of Statistics, 1995), reinforcing the argument that SES domains differ across age groups. In general, the findings also supported the hypotheses that women with low SES would have poorer health outcomes than higher SES women, and that the magnitude of these effects would differ according to the specific SES domain and by age group, with fewer and smaller differences observed among older women. The main exception was that in the older cohort, the education domain was significantly associated with specific health conditions. Results suggest that relations between SES and health are highly complex and vary by age, SES domain, and the health outcome under study.

Carpogenic germination of Sclerotinia minor and potential distribution in Australia

This study confirms that Australian isolates of Sclerotinia minor can produce fertile apothecia and further demonstrates that ascospores collected from these apothecia are pathogenic to sunflower (Helianthus annuus). Sunflower is a known host of the related fungus Sclerotinia sclerotiorum and is grown in some regions where S. minor is known to occur. Head rot symptoms were produced following inoculation with S. minor ascospores. Predictive modeling using CLIMEX software suggested that conditions suitable for carpogenic germination of S. minor probably occur in Australia particularly in southern regions. Carpogenic germination is probably a rare event in northern regions and, if it does occur, probably does not coincide with anthesis in sunflower crops, therefore allowing disease escape.

Using siting algorithms in the design of marine reserve networks

Using benthic habitat data from the Florida Keys (USA), we demonstrate how siting algorithms can help identify potential networks of marine reserves that comprehensively represent target habitat types. We applied a flexible optimization tool-simulated annealing-to represent a fixed proportion of different marine habitat types within a geographic area. We investigated the relative influence of spatial information, planning-unit size, detail of habitat classification, and magnitude of the overall conservation goal on the resulting network scenarios. With this method, we were able to identify many adequate reserve systems that met the conservation goals, e.g., representing at least 20% of each conservation target (i.e., habitat type) while fulfilling the overall aim of minimizing the system area and perimeter. One of the most useful types of information provided by this siting algorithm comes from an irreplaceability analysis, which is a count of the number of, times unique planning units were included in reserve system scenarios. This analysis indicated that many different combinations of sites produced networks that met the conservation goals. While individual 1-km(2) areas were fairly interchangeable, the irreplaceability analysis highlighted larger areas within the planning region that were chosen consistently to meet the goals incorporated into the algorithm. Additionally, we found that reserve systems designed with a high degree of spatial clustering tended to have considerably less perimeter and larger overall areas in reserve-a configuration that may be preferable particularly for sociopolitical reasons. This exercise illustrates the value of using the simulated annealing algorithm to help site marine reserves: the approach makes efficient use of;available resources, can be used interactively by conservation decision makers, and offers biologically suitable alternative networks from which an effective system of marine reserves can be crafted.

Variation in articulatory timing of three English consonants: An electropalatographic investigation

Increasingly, electropalatography (EPG) is being used in speech pathology research to identify and describe speech disorders of neurological origin. However, limited data currently exists that describes normal articulatory segment timing and the degree of variability exhibited by normal speakers when assessed with EPG. Therefore, the purpose of the current investigation was to use the Reading EPG3 system to quantify segmental timing values and examine articulatory timing variability for three English consonants. Ten normal subjects repeated ten repetitions of CV words containing the target consonants /t/, /l/, and /s/ while wearing an artificial palate. The target consonants were followed by the /i/ vowel and were contained in the carrier phrase 'I saw a __'. Mean duration of the approach, closure/constriction, and release phases of consonant articulation were calculated. In addition, inter-subject articulatory timing variability was investigated using descriptive graphs and intra-subject articulatory timing variability was investigated using a coefficient of variation. Results revealed the existence of intersubject variability for mean segment timing values. This could be attributed to individual differences in the suprasegmental features of speech and individual differences in oral cavity size and structure. No significant differences were reported for degree of intra-subject variability between the three sounds for these same phases of articulation. However, when this data set was collapsed, results revealed that the closure/constriction phase of consonant articulation exhibited significantly less intra-subject variability than both the approach and release phases. The stabilization of the tongue against the fixed structure of the hard palate during the closure phase of articulation may have reduced the levels of intra-subject variability.

Discrete element modelling of the influence of lifters on power draw of tumbling mills

Crushing and grinding are the most energy intensive part of the mineral recovery process. A major part of rock size reduction occurs in tumbling mills. Empirical models for the power draw of tumbling mills do not consider the effect of lifters. Discrete element modelling was used to investigate the effect of lifter condition on the power draw of tumbling mill. Results obtained with PFC3D code show that lifter condition will have a significant influence on the power draw and on the mode of energy consumption in the mill. Relatively high lifters will consume less power than low lifters, under otherwise identical conditions. The fraction of the power that will be consumed as friction will increase as the height of the lifters decreases. This will result in less power being used for high intensity comminution caused by the impacts. The fraction of the power that will be used to overcome frictional resistance is determined by the material's coefficient of friction. Based on the modelled results, it appears that the effective coefficient of friction for in situ mill is close to 0.1. (C) 2003 Elsevier Science Ltd. All rights reserved.

Applying discrete element modelling to vertical and horizontal shaft impact crushers

The PFC3D (particle flow code) that models the movement and interaction of particles by the DEM techniques was employed to simulate the particle movement and to calculate the velocity and energy distribution of collision in two types of impact crusher: the Canica vertical shaft crusher and the BJD horizontal shaft swing hammer mill. The distribution of collision energies was then converted into a product size distribution for a particular ore type using JKMRC impact breakage test data. Experimental data of the Canica VSI crusher treating quarry and the BJD hammer mill treating coal were used to verify the DEM simulation results. Upon the DEM procedures being validated, a detailed simulation study was conducted to investigate the effects of the machine design and operational conditions on velocity and energy distributions of collision inside the milling chamber and on the particle breakage behaviour. (C) 2003 Elsevier Ltd. All rights reserved.

Slurry flow in mills: grate-pulp lifter discharge systems (Part 2)

Pulp lifters, also known, as pan lifters are an integral part of the majority of autogenous (AG), semi-autogenous (SAG) and grate discharge ball mills. The performance of the pulp lifters in conjunction with grate design determines the ultimate flow capacity of these mills. Although the function of the pulp lifters is simply to transport the slurry passed through the discharge grate into the discharge trunnion, their performance depends on their design as well as that of the grate and operating conditions such as mill speed and charge level. However, little or no work has been reported on the performance of grate-pulp lifter assemblies and in particular the influence of pulp lifter design on slurry transport. Ideally, the discharge rate through a grate-pulp lifter assembly should be equal to the discharge rate through at a given mill hold-up. However, the results obtained have shown that conventional pulp lifter designs cause considerable restrictions to flow resulting in reduced flow capacity. In this second of a two-part series of papers the performance of conventional pulp lifters (radial and spiral designs) is described and is based on extensive test work carried out in a I m diameter pilot SAG mill. (C) 2003 Elsevier Science Ltd. All rights reserved.

Slurry flow in mills: grate-only discharge mechanism (Part-1)

Discharge grates play an important role in determining the performance of autogenous, semi-autogenous and grate discharge ball mills. The flow capacity (grinding capacity) of these mills is strongly influenced by the discharge grate design-open area and position of apertures, as well as the performance of the pulp lifters. As mill sizes have progressively increased and closed-circuiting has become more popular the importance of grate and pulp lifter design has grown. Unfortunately very few studies have concentrated on this aspect of mill performance. To remedy this a series of laboratory and pilot-scale tests were undertaken to study both the performance of grates on their own and in conjunction with pulp lifters. In this first paper of a two-part series the results from the grate-only experiments are presented and discussed, whilst the performance of the grate-pulp-lifter system is covered in the second paper. The results from the grate-only experiments have shown that the build-up of slurry (hold-up) inside the mill starts from the shoulder of the charge, while the toe position of the slurry progressively moves towards the toe of the charge with increasing flowrate. Besides grate design (open area and position of apertures), charge volume and mill speed were also found to have a strong influence on mill hold-up and interact with grate design variables. (C) 2003 Elsevier Science Ltd. All rights reserved.

Discrete element modelling of power draw of tumbling mills

The power required to operate large mills is typically 5-10 MW. Hence, optimisation of power consumption will have a significant impact on overall economic performance and environmental impact. Power draw modelling results using the discrete element code PFC3D have been compared with results derived from the widely used empirical Model of Morrell. This is achieved by calculating the power draw for a range of operating conditions for constant mill size and fill factor using two modelling approaches. fThe discrete element modelling results show that, apart from density, selection of the appropriate material damping ratio is critical for the accuracy of modelling of the mill power draw. The relative insensitivity of the power draw to the material stiffness allows selection of moderate stiffness values, which result in acceptable computation time. The results obtained confirm that modelling of the power draw for a vertical slice of the mill, of thickness 20% of the mill length, is a reliable substitute for modelling the full mill. The power draw predictions from PFC3D show good agreement with those obtained using the empirical model. Due to its inherent flexibility, power draw modelling using PFC3D appears to be a viable and attractive alternative to empirical models where necessary code and computer power are available.

Comparison of DEM and experiment for a scale model SAG mill

Predictions of flow patterns in a 600-mm scale model SAG mill made using four classes of discrete element method (DEM) models are compared to experimental photographs. The accuracy of the various models is assessed using quantitative data on shoulder, toe and vortex center positions taken from ensembles of both experimental and simulation results. These detailed comparisons reveal the strengths and weaknesses of the various models for simulating mills and allow the effect of different modelling assumptions to be quantitatively evaluated. In particular, very close agreement is demonstrated between the full 3D model (including the end wall effects) and the experiments. It is also demonstrated that the traditional two-dimensional circular particle DEM model under-predicts the shoulder, toe and vortex center positions and the power draw by around 10 degrees. The effect of particle shape and the dimensionality of the model are also assessed, with particle shape predominantly affecting the shoulder position while the dimensionality of the model affects mainly the toe position. Crown Copyright (C) 2003 Published by Elsevier Science B.V. All rights reserved.