Quasi-cylindrical approximation to the swirling flow in an atomizer chamber

A quasi-cylindrical approximation is used to analyse the axisymmetric swirling flow of a liquid with a hollow air core in the chamber of a pressure swirl atomizer. The liquid is injected into the chamber with an azimuthal velocity component through a number of slots at the periphery of one end of the chamber, and flows out as an anular sheet through a central orifice at the other end, following a conical convergence of the chamber wall. An effective inlet condition is used to model the effects of the slots and the boundary layer that develops at the nearby endwall of the chamber. An analysis is presented of the structure of the liquid sheet at the end of the exit orifice, where the flow becomes critical in the sense that upstream propagation of long-wave perturbations ceases to be possible. This nalysis leads to a boundary condition at the end of the orifice that is an extension of the condition of maximum flux used with irrotational models of the flow. As is well known, the radial pressure gradient induced by the swirling flow in the bulk of the chamber causes the overpressure that drives the liquid towards the exit orifice, and also leads to Ekman pumping in the boundary layers of reduced azimuthal velocity at the convergent wall of the chamber and at the wall opposite to the exit orifice. The numerical results confirm the important role played by the boundary layers. They make the thickness of the liquid sheet at the end of the orifice larger than predicted by rrotational models, and at the same time tend to decrease the overpressure required to pass a given flow rate through the chamber, because the large axial velocity in the boundary layers takes care of part of the flow rate. The thickness of the boundary layers increases when the atomizer constant (the inverse of a swirl number, proportional to the flow rate scaled with the radius of the exit orifice and the circulation around the air core) decreases. A minimum value of this parameter is found below which the layer of reduced azimuthal velocity around the air core prevents the pressure from increasing and steadily driving the flow through the exit orifice. The effects of other parameters not accounted for by irrotational models are also analysed in terms of their influence on the boundary layers.

Strategies for Minimum Distance in Simulated Evacuation of Transport Airplanes

The present paper describes the preliminary stages of the development of a new, comprehensive model conceived to simulate the evacuation of transport airplanes in certification studies. Two previous steps were devoted to implementing an efficient procedure to define the whole geometry of the cabin, and setting up an algorithm for assigning seats to available exits. Now, to clarify the role of the cabin arrangement in the evacuation process, the paper addresses the influence of several restrictions on the seat-to-exit assignment algorithm, maintaining a purely geometrical approach for consistency. Four situations are considered: first, an assignment method without limitations to search the minimum for the total distance run by all passengers along their escaping paths; second, a protocol that restricts the number of evacuees through each exit according to updated FAR 25 capacity; third, a procedure which tends to the best proportional sharing among exits but obliges to each passenger to egress through the nearest fore or rear exits; and fourth, a scenario which includes both restrictions. The four assignment strategies are applied to turboprops, and narrow body and wide body jets. Seat to exit distance and number of evacuees per exit are the main output variables. The results show the influence of airplane size and the impact of non-symmetries and inappropriate matching between size and longitudinal location of exits.

Adaptación de una central térmica de carbón a la Directiva de Emisiones Industriales

El proyecto que se presenta a continuación recoge la adaptación de una Central Térmica de carbón al cumplimiento de la DIRECTIVA 2010/75/UE DEL PARLAMENTO EUROPEO Y DEL CONSEJO de 24 de noviembre de 2010 sobre las emisiones industriales. La Central sobre la que se realiza el proyecto tiene un grupo térmico de carbón suscritico refrigerado por agua, con una potencia a plena carga de 350 MWe y de 190 MWe a mínimo técnico. Genera 1 090 t/h de vapor a 540 °C y 168 kg/cm2 funcionando a plena carga. Actualmente las emisiones de NOx son de 650 mg/m3, (condiciones normales, seco, 6 % O2). El objeto del proyecto es reducir estas emisiones a un valor máximo de 200 mg/m3 en las mismas condiciones. El proyecto analiza detalladamente las condiciones actuales de operación de la instalación en cuanto a combustible utilizado, horas de funcionamiento, condiciones climáticas y producción. Se analiza así mismo, todas las técnicas disponibles en mercado para la reducción del NOx, diferenciando entre medidas primarias (actúan sobre los efectos de formación) y secundarias (limpieza de gases). Las medidas primarias ya están implementadas en la central, por tanto, el proyecto plantea la reducción con medidas secundarias. De las medidas secundarias analizadas se ha seleccionado la instalación de un Reactor de Reducción Selectiva Catalítica (Reactor SCR). Tras un análisis de los diferentes reactores y catalizadores disponibles se ha seleccionado un reactor de configuración High-dust, una disposición de catalizador en 3 capas más 1, cuyos componentes están basados en óxidos metálicos (TiO2, V2O5, WO3) y estructura laminar. Se ha buscado la instalación del reactor para operar a una temperatura inferior a 450 °C. Como agente reductor se ha seleccionado NH3 a una dilución del 24,5 %. El proyecto recoge también el diseño de todo el sistema de almacenamiento, evaporación, dilución e inyección de amoniaco. El resultado del proyecto garantiza una concentración en los gases de salida por la chimenea inferior 180 mg/m3(n) de NOx. La reducción del NOx a los límites establecidos, tienen un coste por MWh neto generado para la central, trabajando 60 % a plena carga y 40 % a mínimo técnico y una amortización de 10 años, de 4,10 €/MWh. ABSTRACT The following project shows the compliance adjustment of a coal-fired power station to the 2010/75/EU Directive of the European Parliament and Council 24th November 2010 on industrial emissions. The project is based on a power station with a subcritical thermal coal unit, cooled with water, with a maximum power of 350 MWe and a technical minimum of 190 MWe. It produces 1 090 t/h of steam at 540 ° C and 168 kg/cm2 operating under full load. Currently, NOx emissions are 650 mg / m3 (normal conditions, dry, 6% O2). The project aims to reduce these emissions to a maximum value of 200 mg / m3 under the same conditions. The project analyses in detail the current operating conditions of the system in terms of fuel used, hours of operation, climatic conditions and production. In addition, it also analyses every available technique of NOx reduction on the market, distinguishing between primary (acting on the effects of formation) and secondary measures (gas cleaning). Primary measures are already implemented in the plant, thus proposing reduction with secondary measures. Among the secondary measures analyzed, it has been selected to install a Selective Catalytic Reduction Reactor (SCR Reactor). Having researched the different reactors and catalysts available, for the reactor has been selected High-dust configuration, an arrangement of catalyst in 3 layers plus 1, whose components are based on metal oxides (TiO2, V2O5, WO3) and laminar structure. The reactor has been sought facility to operate at a temperature below 450 ° C. NH3 diluted to 24,5 % has been selected as reducing agent. The project also includes the design of the entire storage system, evaporation, dilution and ammonia injection. The results of the project ensure a gas concentration in the lower chimney exit below 180 mg / m3(n) NOx. The reduction of NOx to the established limits has a cost per net MWh generated in the plant, working at 60% of full load and at 40% of technical minimum, with an amortization of 10 years, 4,10 € / MWh.

Tridimensional simulation of the speed, pressure and turbulence fields of the air flow on the geometry of a freight truck inside a wind tunnel

This study shows the air flow behavior through the geometry of a freight truck inside a AF6109 wind tunnel with the purpose to predict the speed, pressure and turbulence fields made by the air flow, to decrease the aerodynamic resistance, to calculate the dragging coefficient, to evaluate the aerodynamics of the geometry of the prototype using the CFD technique and to compare the results of the simulation with the results obtained experimentally with the “PETER 739 HAULER” scaled freight truck model located on the floor of the test chamber. The Geometry went through a numerical simulation process using the CFX 5,7. The obtained results showed the behavior of the air flow through the test chamber, and also it showed the variations of speed and pressure at the exit of the chamber and the calculations of the coefficient and the dragging force on the geometry of the freight truck. The evaluation of the aerodynamics showed that the aerodynamic deflector is a device that helped the reduction the dragging produced in a significant way by the air. Furthermore, the dragging coefficient and force on the prototype freight truck could be estimated establishing an incomplete similarity.

Sistema autónomo para carga de baterías mediante una instalación fotovoltaica con aplicación directa al vehículo eléctrico y usos

La situación energética actual es insostenible y como consecuencia se plantea un escenario próximo orientado a conseguir un futuro energético sostenible que permita el desarrollo económico y el bienestar social. La situación ambiental actual está afectada directamente por la combustión de combustibles fósiles que en 2013 constituyeron el 81% de la energía primaria utilizada por el ser humano y son la principal fuente antropogénica de gases de efecto invernadero. Los informes del IPCC1, ponen de manifiesto que el cambio climático se ha consolidado durante los últimos años y en la conferencia de la ONU sobre cambio climático de París que se celebrará a finales de 2015, se pretende que los gobiernos suscriban un acuerdo universal para limitar las emisiones de gases de efecto invernadero y evitar que el incremento de la temperatura media global supere los 2°C. Por otra parte, en el interior de las ciudades es especialmente preocupante, por su efecto directo sobre la salud humana, el impacto ambiental producido por las emisiones de NOx que generan el transporte de personas y mercancías. El sector del transporte fue responsable en 2012 del 27,9% del consumo final de energía. Una vez expuesto el escenario energético y ambiental actual, en esta tesis, se analiza la eficiencia de un sistema autónomo fotovoltaico para la carga de baterías de vehículos eléctricos y el uso del mismo con otras cargas, con el objetivo de aprovechar al máximo la energía eléctrica generada y contribuir a la utilización de energía limpia que no produzca impacto ambiental. Como primer paso para el desarrollo de la tesis se hizo un estudio de trabajos previos comenzando por las primeras aplicaciones de la energía fotovoltaica en los vehículos solares para después pasar a trabajos más recientes enfocados al suministro de energía a los vehículos eléctricos. También se hizo este estudio sobre las metodologías de simulación en los sistemas fotovoltaicos y en el modelado de distintos componentes. Posteriormente se eligieron, dentro de la amplia oferta existente en el mercado, los componentes con características técnicas más adecuadas para este tipo de instalaciones y para las necesidades que se pretenden cubrir. A partir de los parámetros técnicos de los componentes elegidos para configurar la instalación autónoma y utilizando modelos contrastados de distintos componentes, se ha desarrollado un modelo de simulación en ordenador del sistema completo con el que se han hecho simulaciones con distintos modos de demanda de energía eléctrica, según los modos de carga disponibles en el vehículo eléctrico para corriente alterna monofásica de 230 V. También se han simulado distintos tamaños del generador fotovoltaico y del sistema de acumulación de energía eléctrica para poder determinar la influencia de estos parámetros en los balances energéticos del sistema. Utilizando recursos propios el doctorando ha realizado la instalación real de un sistema fotovoltaico que incluye sistema de acumulación e inversor en un edificio de su propiedad. Para la realización de la tesis, La Fundación de Fomento e Innovación Industrial (F2I2) ha facilitado al doctorando un dispositivo que permite realizar la alimentación del vehículo eléctrico en modo 2 (este modo emplea un adaptador que incorpora dispositivos de seguridad y se comunica con el vehículo permitiendo ajustar la velocidad de recarga) y que ha sido necesario para los trabajos desarrollados. Se ha utilizado la red eléctrica como sistema de apoyo de la instalación fotovoltaica para permitir la recarga en el modo 2 que requiere más potencia que la proporcionada por el sistema fotovoltaico instalado. Se han analizado mediante simulación distintos regímenes de carga que se han estudiado experimentalmente en la instalación realizada, a la vez que se han hecho ensayos que se han reproducido mediante simulación con los mismos valores de radiación solar y temperatura con objeto de contrastar el modelo. Se han comparado los resultados experimentales con los obtenidos mediante simulación con objeto de caracterizar el comportamiento del sistema de acumulación (energía eléctrica suministrada y tensión de salida en las baterías) y del generador fotovoltaico (energía eléctrica fotovoltaica suministrada). Por último, se ha realizado un estudio económico de la instalación autónoma fotovoltaica ejecutada y simulada. En el mismo se ha planteado la utilización de fondos propios (como realmente se ha llevado a cabo) y la utilización de financiación, para determinar dos posibles escenarios que pudieran ser de utilidad a un propietario de vehículo eléctrico. Se han comparado los resultados obtenidos en los dos escenarios propuestos del estudio económico del sistema, en cuanto a los parámetros de tiempo de retorno de la inversión, valor actual neto de la inversión y tasa interna de retorno de la misma. Las conclusiones técnicas obtenidas, permiten la utilización del sistema con los modos de carga ensayados y otro tipo de cargas que aprovechen la generación eléctrica del sistema. Las baterías ofrecen mejor comportamiento cuando el aporte fotovoltaico está presente, pero no considera adecuado la conexión de cargas elevadas a un sistema de acumulación de gel (plomo-acido) como el que se ha utilizado, debido al comportamiento de este tipo de baterías ante demandas de intensidad de corriente eléctrica elevadas. Por otra parte, el comportamiento de este tipo de baterías con valores de intensidad de corriente eléctrica inferiores a 10 A en ausencia de energía fotovoltaica, con el objetivo de utilizar la generación de energía eléctrica diaria acumulada en el sistema, sí resulta interesante y ofrece un buen comportamiento del sistema de acumulación. Las circunstancias actuales de mercado, que carece de sistemas de acumulación de litio con precios de compra interesantes, no han permitido poder experimentar este sistema de acumulación en la instalación autónoma fotovoltaica ejecutada, tampoco se ha podido obtener el favor de ningún fabricante para ello. Actualmente hay disponibles sistemas de acumulación en litio que no se comercializan en España y que serían adecuados para el sistema de acumulación de energía propuesto en este estudio, que deja abierta las puertas para futuros trabajos de investigación. Las conclusiones económicas obtenidas, rentabilizan el uso de una instalación autónoma fotovoltaica con consumo instantáneo, sin acumulación de energía eléctrica. El futuro de conexión a red por parte de estas instalaciones, cuando se regule, aportará un incentivo económico para rentabilizar con menos tiempo las instalaciones autónomas fotovoltaicas, esto también deja la puerta abierta a futuros trabajos de investigación. El sistema de acumulación de energía aporta el mayor peso económico de inversión en este tipo de instalaciones. La instalación estudiada aporta indicadores económicos que la hacen rentable, pero se necesitaría que los precios de acumulación de la energía en sistemas eficientes estén comprendidos entre 100-200 €/kWh para que el sistema propuesto en este trabajo resulte atractivo a un potencial propietario de un vehículo eléctrico. ABSTRACT The current energy situation is untenable; it poses a scenario next focused on reaching a sustainable energy future, to allow economic development and social welfare. The environmental current situation is affected directly by the combustion of fossil fuels that in 2013 constituted 81 % of the primary energy used by the human being and they are the principal source human of greenhouse gases. The reports of the IPCC2, they reveal that the climate change has consolidated during the last years and in the conference of the UNO on climate change of Paris that will be celebrated at the end of 2015, there is claimed that the governments sign a universal agreement to limit the emission of greenhouse gases and to prevent that the increase of the global average temperature overcomes them 2°C. On the other hand, inside the cities it is specially worrying, for his direct effect on the human health, the environmental impact produced by the NOx emissions that generate the persons' transport and goods. The sector of the transport was responsible in 2012 of 27,9 % of the final consumption of energy. Once exposed the scenario and present environmental energy, in this thesis, it has analyzed the efficiency of an autonomous photovoltaic system for charging electric vehicles, and the use of the same with other workloads, with the objective to maximize the electrical energy generated and contribute to the use of clean energy that does not produce environmental impact. Since the first step for the development of the thesis did to itself a study of previous works beginning for the first applications of the photovoltaic power in the solar vehicles later to go on to more recent works focused on the power supply to the electrical vehicles. Also this study was done on the methodologies of simulation in the photovoltaic systems and in the shaped one of different components. Later they were chosen, inside the wide existing offer on the market, the components with technical characteristics more adapted for this type of facilities and for the needs that try to cover. From the technical parameters of the components chosen to form the autonomous installation and using models confirmed of different components, a model of simulation has developed in computer of the complete system with which simulations have been done by different manners of demand of electric power, according to the available manners of load in the electrical vehicle for single-phase alternating current of 230 V. Also there have been simulated different sizes of the photovoltaic generator and of the system of accumulation of electric power to be able to determine the influence of these parameters in the energy balances of the system. Using own resources the PhD student has realized a real installation of a photovoltaic system that includes system of accumulation and investing in a building of his property. For the accomplishment of the thesis, The Foundation of Promotion and Industrial Innovation (F2I2) it has facilitated to the PhD student a device that allows to realize the supply of the electrical vehicle in way 2 (this way uses an adapter that incorporates safety devices and communicates with the vehicle allowing to fit the speed of recharges) and that has been necessary for the developed works. The electrical network has been in use as system of support of the photovoltaic installation for allowing it her recharges in the way 2 that more power needs that provided by the photovoltaic installed system. There have been analyzed by means of simulation different rate of load that have been studied experimentally in the realized installation, simultaneously that have done to themselves tests that have reproduced by means of simulation with the same values of solar radiation and temperature in order the model contrasted. The experimental results have been compared by the obtained ones by means of simulation in order to characterize the behavior of the system of accumulation (supplied electric power and tension of exit in the batteries) and of the photovoltaic generator (photovoltaic supplied electric power). Finally, there has been realized an economic study of the autonomous photovoltaic executed and simulated installation. In the same one there has appeared the utilization of own funds (since really it has been carried out) and the utilization of financing, to determine two possible scenes that could be of usefulness to an owner of electrical vehicle. There have been compared the results obtained in both scenes proposed of the economic study of the system, as for the parameters of time of return of the investment, current clear value of the investment and rate hospitalizes of return of the same one. The technical obtained conclusions, they make the utilization of the system viable with the manners of load tested and another type of loads of that they take advantage the electrical generation of the system. The batteries offer better behavior when the photovoltaic contribution is present, but he does not consider to be suitable the connection of loads risen up to a system of accumulation of gel (lead - acid) as the one that has been in use, due to the behavior of this type of batteries before demands of intensity of electrical current raised. On the other hand, the behavior of this type of batteries with low values of intensity of electrical current to 10 To in absence of photovoltaic power, with the aim to use the generation of daily electric power accumulated in the system, yes turns out to be interesting and offers a good behavior of the system of accumulation. The current circumstances of market, which lacks systems of accumulation of lithium with interesting purchase prices, have not allowed to be able to experience this system of accumulation in the autonomous photovoltaic executed installation, neither one could have obtained the favor of any manufacturer for it. Nowadays there are available systems of accumulation in lithium that is not commercialized in Spain and that they would be adapted for the system of accumulation of energy proposed in this study, which makes the doors opened for future works of investigation. The economic obtained conclusions; they make more profitable the use of an autonomous photovoltaic installation with instantaneous consumption, without accumulation of electric power. The future of connection to network on the part of these facilities, when it is regulated, will contribute an economic incentive to make profitable with less time the autonomous photovoltaic facilities, this also leaves the door opened for future works of investigation. The system of accumulation of energy contributes the major economic weight of investment in this type of facilities. The studied installation contributes economic indicators that make her profitable, but it would be necessary that the prices of accumulation of the energy in efficient systems are understood between 100-200 € in order that the system proposed in this work turns out to be attractive to a proprietary potential of an electrical vehicle.

La Península Ibérica en el transporte masivo de mercancías entre Europa y África : futuras autopistas del mar

La competitividad del transporte de mercancías depende del estado y funcionamiento de las redes existentes y de sus infraestructuras, no del modo de transporte. En concreto, la rentabilidad o la reducción de los costes de producción del transporte marítimo se vería incrementado con el uso de buques de mayor capacidad y con el desarrollo de plataformas portuarias de distribución o puertos secos, ya que el 90% del comercio entre la Unión Europea y terceros países se realiza a través de sus puertos a un promedio de 3,2 billones de toneladas de mercancías manipuladas cada año y el 40% del tráfico intraeuropeo utiliza el transporte marítimo de corta distancia. A pesar de que los puertos europeos acogen anualmente a más de 400 millones de pasajeros, los grandes desarrollos se han producido en los puertos del norte de Europa (Róterdam, Amberes, Ámsterdam). Los países del Sur de Europa deben buscar nuevas fórmulas para ser más competitivos, ya sea mediante creación de nuevas infraestructuras o mediante refuerzo de las existentes, ofreciendo los costes de los puertos del Norte. El fomento del transporte marítimo y fluvial como alternativa al transporte por carretera, especialmente el transporte marítimo de corta distancia, ha sido impulsado por la Comisión Europea (CE) desde 2003 a través de programas de apoyo comunitario de aplicación directa a las Autopistas del Mar, a modo de ejemplo, cabría citar los programas Marco Polo I y II, los cuales contaron con una dotación presupuestaria total de 855 millones de euros para el período 2003 – 2013; en ese período de tiempo se establecieron objetivos de reducción de congestión vial y mejora del comportamiento medio ambiental del sistema de transporte de mercancías dentro de la comunidad y la potenciación de la intermodalidad. El concepto de Autopista del Mar surge en el Libro Blanco de Transportes de la Comisión Europea “La política europea de transportes de cara al 2010: La hora de la verdad” del 12 de diciembre de 2001, en el marco de una política europea para fomento y desarrollo de sistemas de transportes sostenibles. Las Autopistas del Mar consisten en rutas marítimas de corta distancia entre dos puntos, de menor distancia que por vía terrestre, en las que a través del transporte intermodal mejoran significativamente los tiempos y costes de la cadena logística, contribuyen a la reducción de accidentes, ruidos y emisiones de CO2 a la atmósfera, permite que los conductores pierdan horas de trabajo al volante y evita el deterioro de las infraestructuras terrestres, con el consiguiente ahorro en mantenimiento. La viabilidad de una Autopista del Mar depende tanto de factores de ubicación geográficos, como de características propias del puerto, pasando por los diferentes requerimientos del mercado en cada momento (energéticos, medio ambientales y tecnológicos). Existe un elemento nuevo creado por la Comisión Europea: la red transeuropea de transportes (RTE-T). En el caso de España, con sus dos accesos por los Pirineos (La Junquera e Irún) como únicos pasos terrestres de comunicación con el continente y con importantes limitaciones ferroviarias debido a los tres anchos de vía distintos, le resta competitividad frente al conjunto europeo; por el contrario, España es el país europeo con más kilómetros de costa (con más de 8.000 km) y con un emplazamiento geográfico estratégico, lo que le convierte en una plataforma logística para todo el sur de Europa, por lo que las Autopistas del Mar tendrán un papel importante y casi obligado para el desarrollo de los grandes corredores marítimos que promueve Europa. De hecho, Gijón y Vigo lo han hecho muy bien con sus respectivas líneas definidas como Autopistas del Mar y que conectan con el puerto francés de Nantes-Saint Nazaire, ya que desde ahí los camiones pueden coger rutas hacia el Norte. Paralelamente, la Unión Europea ha iniciado los pasos para el impulso de la primera Autopista del Mar que conectará España con el mercado de Reino Unido, concretamente los Puertos de Bilbao y Tilbury. Además, España e Italia sellaron un acuerdo internacional para desarrollar Autopistas del Mar entre ambos países, comprometiéndose a impulsar una docena de rutas entre puertos del litoral mediterráneo español y el italiano. Actualmente, están en funcionando los trayectos como Barcelona-Génova, Valencia-Civitavecchia y Alicante- Nápoles, notablemente más cortos por mar que por carretera. Bruselas identificó cuatro grandes corredores marítimos que podrían concentrar una alta densidad de tráfico de buques, y en dos de ellos España ya tenía desde un principio un papel crucial. La Comisión diseñó el 14 de abril de 2004, a través del proyecto West-Mos, una red de tráfico marítimo que tiene como vías fundamentales la denominada Autopista del Báltico (que enlaza Europa central y occidental con los países bálticos), la Autopista de Europa suroriental (que une el Adriático con el Jónico y el Mediterráneo más oriental) y también la Autopista de Europa occidental y la Autopista de Europa suroccidental (que enlazan España con Reino Unido y la Francia atlántica y con la Francia mediterránea e Italia, respectivamente). Para poder establecer Autopistas del Mar entre la Península Ibérica y el Norte de Europa primará especialmente la retirada de camiones en la frontera pirenaica, donde el tráfico pesado tiene actualmente una intensidad media diaria de 8.000 unidades, actuando sobre los puntos de mayor congestión, como por ejemplo los Alpes, los Pirineos, el Canal de la Mancha, las carreteras fronterizas de Francia y Euskadi, y proponiendo el traslado de las mercancías en barcos o en trenes. Por su parte, para contar con los subsidios y apoyos europeos las rutas seleccionadas como Autopistas del Mar deben mantener una serie de criterios de calidad relacionados con la frecuencia, coste “plataforma logística a plataforma logística”, simplicidad en procedimientos administrativos y participación de varios países, entre otros. Los estudios consideran inicialmente viables los tramos marítimos superiores a 450 millas, con un volumen de unas 15.000 plataformas al año y que dispongan de eficientes comunicaciones desde el puerto a las redes transeuropeas de autopistas y ferrocarril. Otro objetivo de las Autopistas del Mar es desarrollar las capacidades portuarias de forma que se puedan conectar mejor las regiones periféricas a escala del continente europeo. En lo que a Puertos se refiere, las terminales en los muelles deben contar con una línea de atraque de 250 m., un calado superior a 8 m., una rampa “ro-ro” de doble calzada, grúas portainer, y garantizar operatividad para un mínimo de dos frecuencias de carga semanales. El 28 de marzo de 2011 se publicó el segundo Libro Blanco sobre el futuro del transporte en Europa “Hoja de ruta hacia un espacio único europeo de transporte: por una política de transportes competitiva y sostenible”, donde se definió el marco general de las acciones a emprender en los próximos diez años en el ámbito de las infraestructuras de transporte, la legislación del mercado interior, la reducción de la dependencia del carbono, la tecnología para la gestión del tráfico y los vehículos limpios, así como la estandarización de los distintos mercados. Entre los principales desafíos se encuentran la eliminación de los cuellos de botella y obstáculos diversos de nuestra red europea de transporte, minimizar la dependencia del petróleo, reducir las emisiones de GEI en un 60% para 2050 con respecto a los niveles de 1990 y la inversión en nuevas tecnologías e infraestructuras que reduzcan estas emisiones de transporte en la UE. La conexión entre la UE y el norte de África provoca elevados niveles de congestión en los puntos más críticos del trayecto: frontera hispano-francesa, corredor del Mediterráneo y el paso del estrecho. A esto se le añade el hecho de que el sector del transporte por carretera está sujeto a una creciente competencia de mercado motivada por la eliminación de las barreras europeas, mayores exigencias de los cargadores, mayores restricciones a los conductores y aumento del precio del gasóleo. Por otro lado, el mercado potencial de pasajeros tiene una clara diferenciación en tipos de flujos: los flujos en el período extraordinario de la Operación Paso del Estrecho (OPE), enfocado principalmente a marroquíes que vuelven a su país de vacaciones; y los flujos en el período ordinario, enfocado a la movilidad global de la población. Por tanto, lo que se pretende conseguir con este estudio es analizar la situación actual del tráfico de mercancías y pasajeros con origen o destino la península ibérica y sus causas, así como la investigación de las ventajas de la creación de una conexión marítima (Autopista del Mar) con el Norte de África, basándose en los condicionantes técnicos, administrativos, económicos, políticos, sociales y medio ambientales. The competitiveness of freight transport depends on the condition and operation of existing networks and infrastructure, not the mode of transport. In particular, profitability could be increased or production costs of maritime transport could be reduced by using vessels with greater capacity and developing port distribution platforms or dry ports, seeing as 90% of trade between the European Union and third countries happens through its ports. On average 3,2 billion tonnes of freight are handled annualy and 40% of intra-European traffic uses Short Sea Shipping. In spite of European ports annually hosting more than 400 million passengers, there have been major developments in the northern European ports (Rotterdam, Antwerp, Amsterdam). Southern European countries need to find new ways to be more competitive, either by building new infrastructure or by strengthening existing infrastructure, offering costs northern ports. The use of maritime and river transport as an alternative to road transport, especially Short Sea Shipping, has been driven by the European Commission (EC) from 2003 through community support programs for the Motorways of the Sea. These programs include, for example, the Marco Polo I and II programs, which had a total budget of 855 million euros for the period 2003-2013. During this time objectives were set for reducing road congestion, improving the environmental performance of the freight transport system within the community and enhancing intermodal transport. The “Motorway of the Sea” concept arises in the European Commission’s Transport White Paper "European transport policy for 2010: time to decide" on 12 December 2001, as part of a European policy for the development and promotion of sustainable transport systems. A Motorway of the Sea is defined as a short sea route between two points, covering less distance than by road, which provides a significant improvement in intermodal transport times and to the cost supply chain. It contributes to reducing accidents, noise and CO2 emissions, allows drivers to shorten their driving time and prevents the deterioration of land infrastructure thereby saving on maintenance costs. The viability of a Motorway of the Sea depends as much on geographical location factors as on characteristics of the port, taking into account the different market requirements at all times (energy, environmental and technological). There is a new element created by the European Commission: the trans-European transport network (TEN-T). In the case of Spain, with its two access points in the Pyrenees (La Junquera and Irun) as the only land crossings connected to the mainland and major railway limitations due to the three different gauges, it appears less competitive compared to Europe as a whole. However, Spain is the European country with the most kilometers of coastline (over 8,000 km) and a strategic geographical location, which makes it a logistics platform for the all of Southern Europe. This is why the Motorways of the Sea will have an important role, and an almost necessary one to develop major maritime corridors that Europe supports. In fact, Gijon and Vigo have done very well with their respective sea lanes defined as Motorways of the Sea and which connect with the French port of Nantes-Saint Nazaire, as from there trucks can use nort-heading routes. In parallel, the European Union has taken the first steps to boost the first Motorway of the Sea linking Spain to the UK market, specifically the ports of Bilbao and Tilbury. Furthermore, Spain and Italy sealed an international agreement to develop Motorways of the Sea between both countries, pledging to develop a dozen routes between ports on the Spanish and Italian Mediterranean coasts. Currently, there are sea lanes already in use such as Barcelona-Genova, Valencia-Civitavecchia and Alicante-Naples, these are significantly shorter routes by sea than by road. Brussels identified four major maritime corridors that could hold heavy concentrate shipping traffic, and Spain had a crucial role in two of these from the beginning. On 14 April 2004 the Commission planned through the West-Mos project, a network of maritime traffic which includes the essential sea passages the so-called Baltic Motorway (linking Central and Western Europe with the Baltic countries), the southeast Europe Motorway (linking the Adriatic to the Ionian and eastern Mediterranean Sea), the Western Europe Motorway and southwestern Europe Motorway (that links Spain with Britain and the Atlantic coast of France and with the French Mediterranean coast and Italy, respectively). In order to establish Motorways of the Sea between the Iberian Peninsula and Northern Europe especially, it is necessary to remove trucks from the Pyrenean border, where sees heavy traffic (on average 8000 trucks per day) and addressing the points of greatest congestion, such as the Alps, the Pyrenees, the English Channel, the border roads of France and Euskadi, and proposing the transfer of freight on ships or trains. For its part, in order to receive subsidies and support from the European Commission, the routes selected as Motorways of the Sea should maintain a series of quality criteria related to frequency, costs "from logistics platform to logistics platform," simplicity in administrative procedures and participation of several countries, among others. To begin with, studies consider viable a maritime stretch of at least 450 miles with a volume of about 15,000 platforms per year and that have efficient connections from port to trans-European motorways and rail networks. Another objective of the Motorways of the Sea is to develop port capacity so that they can better connect peripheral regions across the European continent. Referring ports, the terminals at the docks must have a berthing line of 250 m., a draft greater than 8 m, a dual carriageway "ro-ro" ramp, portainer cranes, and ensure operability for a minimum of two loads per week. On 28 March 2011 the second White Paper about the future of transport in Europe "Roadmap to a Single European Transport Area – Towards a competitive and resource efficient transport system" was published. In this Paper the general framework of actions to be undertaken in the next ten years in the field of transport infrastructure was defined, including internal market legislation, reduction of carbon dependency, traffic management technology and clean vehicles, as well as the standardization of different markets. The main challenges are how to eliminate bottlenecks and various obstacles in our European transport network, minimize dependence on oil, reduce GHG emissions by 60% by 2050 compared to 1990 levels and encourage investment in new technologies and infrastructure that reduce EU transport emissions. The connection between the EU and North Africa causes high levels of congestion on the most critical points of the journey: the Spanish-French border, the Mediterranean corridor and Gibraltar Strait. In addition to this, the road transport sector is subject to increased market competition motivated by the elimination of European barriers, greater demands of shippers, greater restrictions on drivers and an increase in the price of diesel. On the other hand, the potential passenger market has a clear differentiation in type of flows: flows in the special period of the Crossing the Straits Operation (CSO), mainly focused on Moroccans who return home on vacation; and flows in the regular session, focused on the global mobile population. Therefore, what I want to achieve with this study is present an analysis of the current situation of freight and passengers to or from the Iberian Peninsula and their causes, as well as present research on the advantages of creating a maritime connection (Motorways of the Sea) with North Africa, based on the technical, administrative, economic, political, social and environmental conditions.

Garantía de funcionamiento de estaciones de tratamiento terciario de aguas residuales para usos recreativos : controles necesarios

La legislación existente en nuestro país, el Real Decreto 1620/200, de 7 de diciembre, por el que se establece el régimen jurídico de la reutilización de las aguas depuradas, no ha sido modificada en estos últimos años a pesar de las opiniones de expertos y operadores en el sentido que merece una revisión y mejora. Por ello se ha realizado un análisis pormenorizado de toda la legislación existente a nivel país y de otros países con amplia experiencia en reutilización para proponer mejoras o cambios en base a la información recopilada, tanto en estudios específicos de investigación como de los datos obtenidos de operadores y/o explotadores de estaciones regeneradoras de aguas residuales en España. Del estudio surgen algunas propuestas claras que se ponen a consideración de las autoridades. Se ha comprobado que no existen estudios suficientes relacionados a tipos de controles en estaciones de tratamiento terciario de aguas residuales en cada uno de los pasos de la línea de proceso, que permitan conocer las garantías de funcionamiento de dichas etapas y del proceso en su conjunto. De éste modo se podrían analizar todas las etapas por separado y comprobar si el funcionamiento en las condiciones previstas de diseño es apropiado, o si es posible mejorar la eficiencia a partir de estos datos intermedios, en lugar de los controles normales efectuados en la entrada y la salida realizados por los explotadores de las plantas existentes en el país. Existen, sin embargo, investigaciones y datos de casi todas las tecnologías existentes en el mercado relacionadas con la regeneración, lo cual ha permitido identificar sus ventajas e inconvenientes. La aplicación de un proceso de APPCC (Análisis de Peligros y Puntos de Control Críticos) a una planta existente ha permitido comprobar que es una herramienta práctica que permite gestionar la seguridad de un proceso de producción industrial como es el caso de un sistema de reutilización, por lo que se considera conveniente recomendar su aplicación siempre que sea posible. The existing legislation in our country, Royal Decree 1620/2007, of 7th December, establishing the legal regime for the reuse of treated water has not been modified in recent years despite expert and operators opinions in the sense that it deserves review and improvement. Therefore it has been conducted a detailed analysis of all existing legislation at country level and of other countries with extensive experience in water reuse to propose improvements or changes based on the information gathered both in specific research studies and the data obtained from operators and/or operators of regenerative sewage stations in Spain. As a result of these studies, some clear proposals are made to be considered by the authorities. It has been found that there are not enough studies related to types of controls in tertiary wastewater treatment plants, in each step of the process line, that provide insight into the performance guarantees of the mention stages and of the whole process. In this manner all stages could be analyzed separately and check if the operation in the design conditions envisaged is appropriate, or whether it is possible to improve efficiency taking in account these intermediate data, instead to the normal checks at entry and exit carried out by operators in existing plants in the country. There are, however, research and data from almost all technologies existing in the market related to regeneration, which has allowed identified its advantages and disadvantages. The application of a process of HACCP (hazard analysis and critical control points) to an existing plant has shown that it is a practical tool for managing the security of a process of industrial production as is the case of a water reuse system, so it is considered appropriate to recommend application whenever possible.

Método de cálculo para la asignación de ocupantes a los elementos de evacuación de un edificio bajo la hipótesis de bloqueo (según CTE DB-SI3)

El buen dimensionado de los elementos de evacuación de los edificios es fundamental para conseguir una evacuación segura de los ocupantes en un evento accidental de fuego. Para ello es necesario conocer previamente la asignación de personas que previsiblemente los van a utilizar en caso de emergencia. En el presente trabajo de investigación, se desarrolla un método de cálculo que permite abarcar todos los escenarios posibles de bloqueos en caso de incendio permitiendo así conocer de antemano las distribuciones de personas en las vías de evacuación de manera conservadora. Dicho método de cálculo es aplicable tanto la justificación del cumplimiento de CTE DB-SI3, como en cualquier reglamentación internacional de protección contra incendios. ABSTRACT A good dimensioning of egress and elements of evacuation in buildings is essential for a safe evacuation of occupants in event of accidental fire. This requires prior knowledge of allocated number of people that will use them in an emergency. In this research, a calculation method is developed to cover every possible scenario of unavailable exit in case of fire, thereby allowing to know in advance the distributions of people on the escape routes and conservatively. This calculation method is applicable to both the confirmation of compliance with Spanish regulations, as in any international fire code.

UMA ECOLOGIA REFÉM DO PODER ECONÔMICO: Leitura exegética sócio-econômica de Deuteronômio 5,12-15

Com esse trabalho, visamos discutir a tentativa de estabelecer um equilíbrio entre o ser humano e natureza na área rural de Judá, pouco antes do reinado de Josias (640-609 a.C.). Nesse caso, pode-se perguntar: seria o mandamento de Deuteronômio 5,12-15 um discurso ecológico? A partir dos estudos de Frank Crüsemann e Haroldo Reimer se admite que partes das leis veterotestamentárias eram destinadas ao assim chamado grupo povo da terra de Judá, visando à manutenção de seu poder. O grupo teria assumido a liderança em Judá mediante um golpe político e, articulando-se, desde então, numa política de aliança para se conservar no poder, mesmo não o assumindo diretamente. Nesse contexto de política de alianças deve-se procurar a implementação do mandamento de Deuteronômio 5,12-15. Ele teria sido escrito por anciãos, um grupo junto ao qual o povo da terra teria se aliado para que ordenassem sentenças jurídicas para a acomodação social. Nesse caso, inicialmente o portão da cidade, espaço oficial para discussões, reclamações e propostas de intermediações, deve ter sido o lugar de elaboração de sentenças jurídicas sobre a utilização de técnicas na agricultura. Sendo elas posteriormente levadas ao tribunal do templo para passar pelas mãos dos sacerdotes, outro braço da coalizão. O uso dos animais de porte, cujo peso prejudicava as pequenas propriedades de terra de Judá, deve ter sido um motivo de incessantes conflitos entre pequenos e grandes proprietários de terra. Ressaltamos assim que apenas os homens mais abastados de Judá tinham acesso a esses animais. Esta solução, segundo se entende, liga o rodízio de culturas ao descanso do campo pertencente ao povo da terra de Judá. Liga-se o termo sábado com a vida da elite rural judaíta do período do reinado de Josias. Uma saída encontrada pelas elites de Judá, a qual nos leva a ponderar uma situação similar que ocorre na América Latina, diante da globalização. Se o texto Deuteronômio 5,12-15 é uma ponderação das elites hegemônicas de Judá que buscam o equilíbrio entre ser o humano e a natureza (ecologia), o discurso ecológico contemporâneo poderá ter neste texto um importante interlocutor. Esse discurso pode ocultar interesses econômicos, completamente diferentes, pois se trata de uma estratégia dominadora e não libertadora, objetivando-se, sobretudo, a reprodução social. O Brasil e os demais países da América Latina vêm sofrendo, há algum tempo, com essa distância entre a elite e o resto da sociedade. Nossas elites utilizam-se, há tempos, do discurso ecológico para se manterem no poder dessas sociedades. Por exemplo, vemos nos noticiários uma quantidade de programas e manchetes ligadas à destruição da natureza. Isso é interessante porque, após terem eles mesmo destruído a natureza, passam agora a defendê-la; controlando as reservas naturais, garantindo sua produtividade e seu status quo no sistema econômico atual.(AU)

UMA ECOLOGIA REFÉM DO PODER ECONÔMICO: Leitura exegética sócio-econômica de Deuteronômio 5,12-15

Com esse trabalho, visamos discutir a tentativa de estabelecer um equilíbrio entre o ser humano e natureza na área rural de Judá, pouco antes do reinado de Josias (640-609 a.C.). Nesse caso, pode-se perguntar: seria o mandamento de Deuteronômio 5,12-15 um discurso ecológico? A partir dos estudos de Frank Crüsemann e Haroldo Reimer se admite que partes das leis veterotestamentárias eram destinadas ao assim chamado grupo povo da terra de Judá, visando à manutenção de seu poder. O grupo teria assumido a liderança em Judá mediante um golpe político e, articulando-se, desde então, numa política de aliança para se conservar no poder, mesmo não o assumindo diretamente. Nesse contexto de política de alianças deve-se procurar a implementação do mandamento de Deuteronômio 5,12-15. Ele teria sido escrito por anciãos, um grupo junto ao qual o povo da terra teria se aliado para que ordenassem sentenças jurídicas para a acomodação social. Nesse caso, inicialmente o portão da cidade, espaço oficial para discussões, reclamações e propostas de intermediações, deve ter sido o lugar de elaboração de sentenças jurídicas sobre a utilização de técnicas na agricultura. Sendo elas posteriormente levadas ao tribunal do templo para passar pelas mãos dos sacerdotes, outro braço da coalizão. O uso dos animais de porte, cujo peso prejudicava as pequenas propriedades de terra de Judá, deve ter sido um motivo de incessantes conflitos entre pequenos e grandes proprietários de terra. Ressaltamos assim que apenas os homens mais abastados de Judá tinham acesso a esses animais. Esta solução, segundo se entende, liga o rodízio de culturas ao descanso do campo pertencente ao povo da terra de Judá. Liga-se o termo sábado com a vida da elite rural judaíta do período do reinado de Josias. Uma saída encontrada pelas elites de Judá, a qual nos leva a ponderar uma situação similar que ocorre na América Latina, diante da globalização. Se o texto Deuteronômio 5,12-15 é uma ponderação das elites hegemônicas de Judá que buscam o equilíbrio entre ser o humano e a natureza (ecologia), o discurso ecológico contemporâneo poderá ter neste texto um importante interlocutor. Esse discurso pode ocultar interesses econômicos, completamente diferentes, pois se trata de uma estratégia dominadora e não libertadora, objetivando-se, sobretudo, a reprodução social. O Brasil e os demais países da América Latina vêm sofrendo, há algum tempo, com essa distância entre a elite e o resto da sociedade. Nossas elites utilizam-se, há tempos, do discurso ecológico para se manterem no poder dessas sociedades. Por exemplo, vemos nos noticiários uma quantidade de programas e manchetes ligadas à destruição da natureza. Isso é interessante porque, após terem eles mesmo destruído a natureza, passam agora a defendê-la; controlando as reservas naturais, garantindo sua produtividade e seu status quo no sistema econômico atual.(AU)

Antigas memórias bélicas sobre Javé em Juízes 5,3-5.9-13.19-22.23 e em Habacuque 3,3-6

A imagem de Javé em Juízes 5 constitui-se nas primeiras impressões que o Israel antigo teve do seu Deus. Ela desenha a saída de Javé de sua antiga morada no Sinai para adentrar na terra da Palestina, a fim de lutar por seu povo contra a opressão cananéia. O período tribal foi o momento formativo desse antigo conceito de Javé no Antigo Testamento. Grupos israelitas reformularam o conceito de Javé promulgado pela tradição do Sinai, afirmando, assim, que Javé não é mais o Deus estático e teofânico, morador de uma montanha, mas é o Deus de Israel . E a migração da divindade de um monte para um campo de batalha não representa meramente a caminhada dessa divindade, mas representa o caminhar dos vários estágios em que Israel conceituou seu Deus. Decisivo nessas novas articulações teológicas foi o campo de batalha, que foi o moto da celebração à Javé ressalvada em Juízes 5. Javé é celebrado por seu agir histórico! A história é a mediadora entre Javé e seu povo. Ela é a via pela qual se pronuncia sobre Javé. Assim, as novas conjunturas históricas requerem novas formulações sobre Deus. A antiga memória bélica de Javé contida em Juízes 5 perpassa a história da religião de Israel, podendo ser observada também em Habacuque 3,3-6. Esse é um texto do século VII a.C. Assim, detectamos uma memória corrente na história da religião de Israel, que começou nos momentos antecedentes à da formação da monarquia (Juízes 5) e ainda pode ser notada em Habacuque, no século VII a.C. Nesse desenrolar da religião de Israel, a memória bélica sobre Javé esteve sujeita a várias mutações. Mas, essencialmente, manteve sua proposta: tornar os sujeitos da opressão promulgada pelos impérios em agentes de transformação social. O conceito bélico de Javé patrocinou as revoltas contra o despotismo social, sendo, portanto, uma forma de resistência dos grupos desprestigiados da sociedade, em Israel e Judá

Antigas memórias bélicas sobre Javé em Juízes 5,3-5.9-13.19-22.23 e em Habacuque 3,3-6

A imagem de Javé em Juízes 5 constitui-se nas primeiras impressões que o Israel antigo teve do seu Deus. Ela desenha a saída de Javé de sua antiga morada no Sinai para adentrar na terra da Palestina, a fim de lutar por seu povo contra a opressão cananéia. O período tribal foi o momento formativo desse antigo conceito de Javé no Antigo Testamento. Grupos israelitas reformularam o conceito de Javé promulgado pela tradição do Sinai, afirmando, assim, que Javé não é mais o Deus estático e teofânico, morador de uma montanha, mas é o Deus de Israel . E a migração da divindade de um monte para um campo de batalha não representa meramente a caminhada dessa divindade, mas representa o caminhar dos vários estágios em que Israel conceituou seu Deus. Decisivo nessas novas articulações teológicas foi o campo de batalha, que foi o moto da celebração à Javé ressalvada em Juízes 5. Javé é celebrado por seu agir histórico! A história é a mediadora entre Javé e seu povo. Ela é a via pela qual se pronuncia sobre Javé. Assim, as novas conjunturas históricas requerem novas formulações sobre Deus. A antiga memória bélica de Javé contida em Juízes 5 perpassa a história da religião de Israel, podendo ser observada também em Habacuque 3,3-6. Esse é um texto do século VII a.C. Assim, detectamos uma memória corrente na história da religião de Israel, que começou nos momentos antecedentes à da formação da monarquia (Juízes 5) e ainda pode ser notada em Habacuque, no século VII a.C. Nesse desenrolar da religião de Israel, a memória bélica sobre Javé esteve sujeita a várias mutações. Mas, essencialmente, manteve sua proposta: tornar os sujeitos da opressão promulgada pelos impérios em agentes de transformação social. O conceito bélico de Javé patrocinou as revoltas contra o despotismo social, sendo, portanto, uma forma de resistência dos grupos desprestigiados da sociedade, em Israel e Judá

Lack of cell cycle regulation of telomerase activity in human cells

Conflicting reports have appeared concerning the cell cycle regulation of telomerase activity and its possible repression during quiescence and cell differentiation. We have reexamined these issues in an attempt to uncover the basis for the discrepancies. Variations in extracted telomerase activity during the cell cycle are not observed in cells sorted on the basis of DNA content. Variations are observed in cells synchronized using some biochemical cell cycle inhibitors, but only with those agents where cellular toxicity is evident. A progressive decline in telomerase activity is observed in cells whose growth rate is reduced from seven to eight population doublings per week to one to two doublings per week. Telomerase is largely absent in cells that truly exit the cell cycle and do not divide over the 7-day period. Although it is not necessary for all cell types to regulate telomerase in the same way, we conclude that in the immortal cultured cell lines examined, extracted telomerase activity does not change significantly during progression through the stages of the cell cycle. Telomerase activity generally correlates with growth rate and is repressed in cells that exit the cell cycle and become quiescent.

Endoplasmic reticulum quality control of asialoglycoprotein receptor H2a involves a determinant for retention and not retrieval

The human asialoglycoprotein receptor H2a subunit contains a charged pentapeptide, EGHRG, in its ectodomain that is the only sequence absent from the H2b alternatively spliced variant. H2b exits the endoplasmic reticulum (ER) even when singly expressed, whereas H2a gives rise to a cleaved soluble secreted ectodomain fragment; uncleaved membrane-bound H2a molecules are completely retained and degraded in the ER. We have inserted the H2a pentapeptide into the sequence of the H1 subunit (H1i5), which caused complete ER retention but, unexpectedly, no degradation. This suggests that the pentapeptide is a determinant for ER retention not colocalizing in H2a with the determinant for degradation. The state of sugar chain processing and the ER localization of H1i5, which was unchanged at 15°C or after treatment with nocodazole, indicate ER retention and not retrieval from the cis-Golgi or the intermediate compartment. H1i5 folded similarly to H1, and both associated to calnexin. However, whereas H1 dissociated with a half time of 45 min, H1i5 remained bound to the chaperone for prolonged periods. The correct global folding of H2a and H1i5 and of other normal precursors and unassembled proteins and the true ER retention, and not exit and retrieval, suggest a difference in their quality control mechanism compared with that of misfolded proteins, which does involve retrieval. However, both pathways may involve calnexin.

A model of excitation and adaptation in bacterial chemotaxis

Bacterial chemotaxis is widely studied because of its accessibility and because it incorporates processes that are important in a number of sensory systems: signal transduction, excitation, adaptation, and a change in behavior, all in response to stimuli. Quantitative data on the change in behavior are available for this system, and the major biochemical steps in the signal transduction/processing pathway have been identified. We have incorporated recent biochemical data into a mathematical model that can reproduce many of the major features of the intracellular response, including the change in the level of chemotactic proteins to step and ramp stimuli such as those used in experimental protocols. The interaction of the chemotactic proteins with the motor is not modeled, but we can estimate the degree of cooperativity needed to produce the observed gain under the assumption that the chemotactic proteins interact directly with the motor proteins.