Influência do aporte térmico da soldagem GTAW no balanço de fases Ferrita/Austenita do Aço Inoxidável Duplex UNS S32205

Pós-graduação em Engenharia Mecânica - FEIS

Síntese, caracterização e estudo do comportamento térmico dos glicolatos de lantanídeos e ítrio no estado sólido

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise numérica de uma geometria de coletor solar para sistemas de aquecimento de água

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Infecção experimental para avaliar a excreção do vírus da diarreia viral bovina por leitões desmamados e transmissão viral por via aerógena

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da modificação da fotoluminescência em α-Bi2O3 após tratamento térmico assistido por pressão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise numérica de um sistema integrado coletor solar/armazenador térmico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Levantamento de coeficientes de desempenho de refrigeradores domésticos associados a armazenador térmico

Pós-graduação em Engenharia Mecânica - FEB

Ambiente térmico y el bienestar de los cerdos en el período de descanso previo al sacrificio

The research aimed to evaluate the relationship between the thermal environment of the rest pens in a pig slaughterhouse and the surface temperature (ST) of the animals as well as the effect of intermittent water spraying on thermal comfort. There were two visits to slaughter industrial being in each selected three pens of rest, one for control treatment (no spray throughout the period) and two for the treatment of intermittent spraying water (30 minutes intervals with constant spray followed by 30 minutes then turned off). Assessments began at the time of discharging animals in which are taken the thermographic images from lots using an infrared thermographic camera. After housing in the pens, were registered the thermographic images and the respiratory frequency (RF) every five minutes for four hours. Were evaluated the temperature, relative humidity and temperature-humidity index (THI). Considering the values of THI was observed that the animals remained in a condition of comfort only at the time of his arrival at the slaughterhouse. The ST and RF of the animals kept in the pens without sprinkler system (control) showed a linear increase in function of time of day, with increasing temperature. The treatment with intermittent sprinkling of water was observed oscillatory behavior of the ST and RF, however it was always lower than the control treatment, even in times when the water sprinklers were turned off. The time required of spray to reduction and stabilization of the ST of the animals was limited to the combination of temperature and relative humidity, being estimated at 25 minutes at times of higher THI. The maximum environmental temperature during evaluation was 28.4 oC.

Monitoramento do tempo de prensagem e do comportamento da temperatura através da espessura de painéis LVL (Laminated veneer lumber)

The aim of this study was to analyze the behavior of the flow of heat (temperature) through the thickness of panels LVL (Laminated veneer lumber) produced with phenol formaldehyde adhesive, in laboratorial and industrial scales. Experimental program was conducted with five LVL panels (three produced in laboratorial scale and two in industrial scale) with different arrangements of a mix of commercial veneers from tropical pinus from the south region of Sao Paulo State, Brazil, bonded using phenol formaldehyde adhesive. The temperature inside the panels during the pressing process was evaluated using thermocouples type T (cooper-constantan), installed mostly in the center of the glue lines and connected to a data acquisition system. The graphics of temperature as a function of the time showed a gradual increase of temperature up to pre-set values, remaining constant from them. The temperature reached at the center of the panels was adequate to promote the curing of the adhesive. These pre-set values were similar to the minimum values presented by other authors and manufacturers of these adhesives that affirm that temperatures above 100ºC at the center of laminated panels bonded with phenolic adhesives are sufficient to ensure proper cure of the resin. The time necessary for curing of the adhesives confirmed the validity of practical expressions provided by adhesive manufacturers.

Alterações celulares induzidas pelo estresse térmico em embriões bovinos

Fundação de Apoio à Pesquisa do Estado de São Paulo (FAPESP)

Isolamento e caracterização de ciclotídeos da espécie Noisettia orchidiflora (Rudge) Ging.

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Isolamento de sequências repetitivas do genoma de espécies do gênero Ancistrus (Siluriformes: Loricariidae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da influência do tratamento térmico a laser nas características dos aços avançados de alta resistência dual phase 600 e transformed induced plasticity 750

Pós-graduação em Engenharia Mecânica - FEG

Caracterização morfológica e cristalográfica da zircônia após desgaste com pedra diamantada e elaboração de um protocolo para tratamento térmico regenerativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Soroprevalência, isolamento e diagnóstico molecular para leptospirose em bovinos de fazendas de cria e de centrais de receptoras de embrião da região de Bauru- SP: Diagnóstico de leptospirose bovina em Bauru - SP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)