Time-domain models for power system stability and unbalance

It is an important and difficult challenge to protect modern interconnected power system from blackouts. Applying advanced power system protection techniques and increasing power system stability are ways to improve the reliability and security of power systems. Phasor-domain software packages such as Power System Simulator for Engineers (PSS/E) can be used to study large power systems but cannot be used for transient analysis. In order to observe both power system stability and transient behavior of the system during disturbances, modeling has to be done in the time-domain. This work focuses on modeling of power systems and various control systems in the Alternative Transients Program (ATP). ATP is a time-domain power system modeling software in which all the power system components can be modeled in detail. Models are implemented with attention to component representation and parameters. The synchronous machine model includes the saturation characteristics and control interface. Transient Analysis Control System is used to model the excitation control system, power system stabilizer and the turbine governor system of the synchronous machine. Several base cases of a single machine system are modeled and benchmarked against PSS/E. A two area system is modeled and inter-area and intra-area oscillations are observed. The two area system is reduced to a two machine system using reduced dynamic equivalencing. The original and the reduced systems are benchmarked against PSS/E. This work also includes the simulation of single-pole tripping using one of the base case models. Advantages of single-pole tripping and comparison of system behavior against three-pole tripping are studied. Results indicate that the built-in control system models in PSS/E can be effectively reproduced in ATP. The benchmarked models correctly simulate the power system dynamics. The successful implementation of a dynamically reduced system in ATP shows promise for studying a small sub-system of a large system without losing the dynamic behaviors. Other aspects such as relaying can be investigated using the benchmarked models. It is expected that this work will provide guidance in modeling different control systems for the synchronous machine and in representing dynamic equivalents of large power systems.

Implementation of porous silicon technology for a fluidic flow-through optical sensor for pH measurements

This work presents an innovative integration of sensing and nano-scaled fluidic actuation in the combination of pH sensitive optical dye immobilization with the electro-osmotic phenomena in polar solvents like water for flow-through pH measurements. These flow-through measurements are performed in a flow-through sensing device (FTSD) configuration that is designed and fabricated at MTU. A relatively novel and interesting material, through-wafer mesoporous silica substrates with pore diameters of 20 -200 nm and pore depths of 500 µm are fabricated and implemented for electro-osmotic pumping and flow-through fluorescence sensing for the first time. Performance characteristics of macroporous silicon (> 500 µm) implemented for electro-osmotic pumping include, a very large flow effciency of 19.8 µLmin-1V-1 cm-2 and maximum pressure effciency of 86.6 Pa/V in comparison to mesoporous silica membranes with 2.8 µLmin-1V-1cm-2 flow effciency and a 92 Pa/V pressure effciency. The electrical current (I) of the EOP system for 60 V applied voltage utilizing macroporous silicon membranes is 1.02 x 10-6A with a power consumption of 61.74 x 10-6 watts. Optical measurements on mesoporous silica are performed spectroscopically from 300 nm to 1000 nm using ellipsometry, which includes, angularly resolved transmission and angularly resolved reflection measurements that extend into the infrared regime. Refractive index (n) values for oxidized and un-oxidized mesoporous silicon sample at 1000 nm are found to be 1.36 and 1.66. Fluorescence results and characterization confirm the successful pH measurement from ratiometric techniques. The sensitivity measured for fluorescein in buffer solution is 0.51 a.u./pH compared to sensitivity of ~ 0.2 a.u./pH in the case of fluorescein in porous silica template. Porous silica membranes are efficient templates for immobilization of optical dyes and represent a promising method to increase sensitivity for small variations in chemical properties. The FTSD represents a device topology suitable for application to long term monitoring of lakes and reservoirs. Unique and important contributions from this work include fabrication of a through-wafer mesoporous silica membrane that has been thoroughly characterized optically using ellipsometry. Mesoporous silica membranes are tested as a porous media in an electro-osmotic pump for generating high pressure capacities due to the nanometer pore sizes of the porous media. Further, dye immobilized mesoporous silica membranes along with macroporous silicon substrates are implemented for continuous pH measurements using fluorescence changes in a flow-through sensing device configuration. This novel integration and demonstration is completely based on silicon and implemented for the first time and can lead to miniaturized flow-through sensing systems based on MEMS technologies.

Design of high fidelity building energy monitoring system

Building energy meter network, based on per-appliance monitoring system, willbe an important part of the Advanced Metering Infrastructure. Two key issues exist for designing such networks. One is the network structure to be used. The other is the implementation of the network structure on a large amount of small low power devices, and the maintenance of high quality communication when the devices have electric connection with high voltage AC line. The recent advancement of low-power wireless communication makes itself the right candidate for house and building energy network. Among all kinds of wireless solutions, the low speed but highly reliable 802.15.4 radio has been chosen in this design. While many network-layer solutions have been provided on top of 802.15.4, an IPv6 based method is used in this design. 6LOWPAN is the particular protocol which adapts IP on low power personal network radio. In order to extend the network into building area without, a specific network layer routing mechanism-RPL, is included in this design. The fundamental unit of the building energy monitoring system is a smart wall plug. It is consisted of an electricity energy meter, a RF communication module and a low power CPU. The real challenge for designing such a device is its network firmware. In this design, IPv6 is implemented through Contiki operation system. Customize hardware driver and meter application program have been developed on top of the Contiki OS. Some experiments have been done, in order to prove the network ability of this system.

Algorithms for spacecraft formation flying navigation based on wireless positioning system measurements

Spacecraft formation flying navigation continues to receive a great deal of interest. The research presented in this dissertation focuses on developing methods for estimating spacecraft absolute and relative positions, assuming measurements of only relative positions using wireless sensors. The implementation of the extended Kalman filter to the spacecraft formation navigation problem results in high estimation errors and instabilities in state estimation at times. This is due tp the high nonlinearities in the system dynamic model. Several approaches are attempted in this dissertation aiming at increasing the estimation stability and improving the estimation accuracy. A differential geometric filter is implemented for spacecraft positions estimation. The differential geometric filter avoids the linearization step (which is always carried out in the extended Kalman filter) through a mathematical transformation that converts the nonlinear system into a linear system. A linear estimator is designed in the linear domain, and then transformed back to the physical domain. This approach demonstrated better estimation stability for spacecraft formation positions estimation, as detailed in this dissertation. The constrained Kalman filter is also implemented for spacecraft formation flying absolute positions estimation. The orbital motion of a spacecraft is characterized by two range extrema (perigee and apogee). At the extremum, the rate of change of a spacecraft’s range vanishes. This motion constraint can be used to improve the position estimation accuracy. The application of the constrained Kalman filter at only two points in the orbit causes filter instability. Two variables are introduced into the constrained Kalman filter to maintain the stability and improve the estimation accuracy. An extended Kalman filter is implemented as a benchmark for comparison with the constrained Kalman filter. Simulation results show that the constrained Kalman filter provides better estimation accuracy as compared with the extended Kalman filter. A Weighted Measurement Fusion Kalman Filter (WMFKF) is proposed in this dissertation. In wireless localizing sensors, a measurement error is proportional to the distance of the signal travels and sensor noise. In this proposed Weighted Measurement Fusion Kalman Filter, the signal traveling time delay is not modeled; however, each measurement is weighted based on the measured signal travel distance. The obtained estimation performance is compared to the standard Kalman filter in two scenarios. The first scenario assumes using a wireless local positioning system in a GPS denied environment. The second scenario assumes the availability of both the wireless local positioning system and GPS measurements. The simulation results show that the WMFKF has similar accuracy performance as the standard Kalman Filter (KF) in the GPS denied environment. However, the WMFKF maintains the position estimation error within its expected error boundary when the WLPS detection range limit is above 30km. In addition, the WMFKF has a better accuracy and stability performance when GPS is available. Also, the computational cost analysis shows that the WMFKF has less computational cost than the standard KF, and the WMFKF has higher ellipsoid error probable percentage than the standard Measurement Fusion method. A method to determine the relative attitudes between three spacecraft is developed. The method requires four direction measurements between the three spacecraft. The simulation results and covariance analysis show that the method’s error falls within a three sigma boundary without exhibiting any singularity issues. A study of the accuracy of the proposed method with respect to the shape of the spacecraft formation is also presented.

Muffler characterization with implementation of the finite element method and experimental techniques

Determining how an exhaust system will perform acoustically before a prototype muffler is built can save the designer both a substantial amount of time and resources. In order to effectively use the simulation tools available it is important to understand what is the most effective tool for the intended purpose of analysis as well as how typical elements in an exhaust system affect muffler performance. An in-depth look at the available tools and their most beneficial uses are presented in this thesis. A full parametric study was conducted using the FEM method for typical muffler elements which was also correlated to experimental results. This thesis lays out the overall ground work on how to accurately predict sound pressure levels in the free field for an exhaust system with the engine properties included. The accuracy of the model is heavily dependent on the correct temperature profile of the model in addition to the accuracy of the source properties. These factors will be discussed in detail and methods for determining them will be presented. The secondary effects of mean flow, which affects both the acoustical wave propagation and the flow noise generation, will be discussed. Effective ways for predicting these secondary effects will be described. Experimental models will be tested on a flow rig that showcases these phenomena.

Implementation of Evidence-Based Practices for Treatment of Alcohol and Drug Disorders: The Role of the State Authority

The current climate of increasing performance expectations and diminishing resources, along with innovations in evidence-based practices (EBPs), creates new dilemmas for substance abuse treatment providers, policymakers, funders, and the service delivery system. This paper describes findings from baseline interviews with representatives from 49 state substance abuse authorities (SSAs). Interviews assessed efforts aimed at facilitating EBP adoption in each state and the District of Columbia. Results suggested that SSAs are concentrating more effort on EBP implementation strategies such as education, training, and infrastructure development, and less effort on financial mechanisms, regulations, and accreditation. The majority of SSAs use EBPs as a criterion in their contracts with providers, and just over half reported that EBP use is tied to state funding. To date, Oregon remains the only state with legislation that mandates treatment expenditures for EBPs; North Carolina follows suit with legislation that requires EBP promotion within current resources.

HIGH PERFORMANCE, LOW COST SUBSPACE DECOMPOSITION AND POLYNOMIAL ROOTING FOR REAL TIME DIRECTION OF ARRIVAL ESTIMATION: ANALYSIS AND IMPLEMENTATION

This thesis develops high performance real-time signal processing modules for direction of arrival (DOA) estimation for localization systems. It proposes highly parallel algorithms for performing subspace decomposition and polynomial rooting, which are otherwise traditionally implemented using sequential algorithms. The proposed algorithms address the emerging need for real-time localization for a wide range of applications. As the antenna array size increases, the complexity of signal processing algorithms increases, making it increasingly difficult to satisfy the real-time constraints. This thesis addresses real-time implementation by proposing parallel algorithms, that maintain considerable improvement over traditional algorithms, especially for systems with larger number of antenna array elements. Singular value decomposition (SVD) and polynomial rooting are two computationally complex steps and act as the bottleneck to achieving real-time performance. The proposed algorithms are suitable for implementation on field programmable gated arrays (FPGAs), single instruction multiple data (SIMD) hardware or application specific integrated chips (ASICs), which offer large number of processing elements that can be exploited for parallel processing. The designs proposed in this thesis are modular, easily expandable and easy to implement. Firstly, this thesis proposes a fast converging SVD algorithm. The proposed method reduces the number of iterations it takes to converge to correct singular values, thus achieving closer to real-time performance. A general algorithm and a modular system design are provided making it easy for designers to replicate and extend the design to larger matrix sizes. Moreover, the method is highly parallel, which can be exploited in various hardware platforms mentioned earlier. A fixed point implementation of proposed SVD algorithm is presented. The FPGA design is pipelined to the maximum extent to increase the maximum achievable frequency of operation. The system was developed with the objective of achieving high throughput. Various modern cores available in FPGAs were used to maximize the performance and details of these modules are presented in detail. Finally, a parallel polynomial rooting technique based on Newton’s method applicable exclusively to root-MUSIC polynomials is proposed. Unique characteristics of root-MUSIC polynomial’s complex dynamics were exploited to derive this polynomial rooting method. The technique exhibits parallelism and converges to the desired root within fixed number of iterations, making this suitable for polynomial rooting of large degree polynomials. We believe this is the first time that complex dynamics of root-MUSIC polynomial were analyzed to propose an algorithm. In all, the thesis addresses two major bottlenecks in a direction of arrival estimation system, by providing simple, high throughput, parallel algorithms.

The Influence of Enterprise Systems on Business and Information Technology

Business strategy is important to all organizations. Nearly all Fortune 500 firms are implementing Enterprise Resource Planning (ERP) systems to improve the execution of their business strategy and to improve integration with its information technology (IT) strategy. Successful implementation of these multi-million dollar software systems are requiring new emphasis on change management and on Business and IT strategic alignment. This paper examines business and IT strategic alignment and seeks to explore whether an ERP implementation can drive business process reengineering and business and IT strategic alignment. An overview of business strategy and strategic alignment are followed by an analysis of ERP. The “As-Is/To-Be” process model is then presented and explained as a simple, but vital tool for improving business strategy, strategic alignment, and ERP implementation success.

Driving the refactoring of Java Enterprise applications by evaluating the distance between application elements

Java Enterprise Applications (JEAs) are complex systems composed using various technologies that in turn rely on languages other than Java, such as XML or SQL. Given the complexity of these applications, the need to reverse engineer them in order to support further development becomes critical. In this paper we show how it is possible to split a system into layers and how is possible to interpret the distance between application elements in order to support the refactoring of JEAs. The purpose of this paper is to explore ways to provide suggestions about the refactoring operations to perform on the code by evaluating the distance between layers and elements belonging those layers. We split JEAs into layers by considering the kinds and the purposes of the elements composing the application. We measure distance between elements by using the notion of the shortest path in a graph. Also we present how to enrich the interpretation of the distance value with enterprise pattern detection in order to refine the suggestion about modifications to perform on the code.

PyGirl Generating Whole-System VMs from high-level models using PyPy

Virtual machines emulating hardware devices are generally implemented in low-level languages and using a low-level style for performance reasons. This trend results in largely difficult to understand, difficult to extend and unmaintainable systems. As new general techniques for virtual machines arise, it gets harder to incorporate or test these techniques because of early design and optimization decisions. In this paper we show how such decisions can be postponed to later phases by separating virtual machine implementation issues from the high-level machine-specific model. We construct compact models of whole-system VMs in a high-level language, which exclude all low-level implementation details. We use the pluggable translation toolchain PyPy to translate those models to executables. During the translation process, the toolchain reintroduces the VM implementation and optimization details for specific target platforms. As a case study we implement an executable model of a hardware gaming device. We show that our approach to VM building increases understandability, maintainability and extendability while preserving performance.

PyGirl: Generating Whole-System VMs from High-Level Prototypes Using PyPy

Virtual machines (VMs) emulating hardware devices are generally implemented in low-level languages for performance reasons. This results in unmaintainable systems that are difficult to understand. In this paper we report on our experience using the PyPy toolchain to improve the portability and reduce the complexity of whole-system VM implementations. As a case study we implement a VM prototype for a Nintendo Game Boy, called PyGirl, in which the high-level model is separated from low-level VM implementation issues. We shed light on the process of refactoring from a low-level VM implementation in Java to a high-level model in RPython. We show that our whole-system VM written with PyPy is significantly less complex than standard implementations, without substantial loss in performance.

„RFID - Systematische Versuche für den zuverlässigen Einsatz in der Logistik“

Mit zunehmender Komplexität und Vielfalt der Logistikprozesse steigt der Stellenwert der eingesetzten Informationstechnologien. Die den Warenfluss begleitenden bzw. vorhereilenden Informationen sind erforderlich, um Waren identifizieren und Unternehmensressourcen optimal einsetzen zu können. Als Beispiel ist der klassische Wareneingang zu nennen. Durch die Avisierung von Menge und Art eingehender Waren können der Einsatz des Personals zur Entladung und Vereinnahmung sowie die erforderlichen Ressourcen (Ladehilfsmittel, Flurförderzeuge, usw.) im Vorfeld geplant und bereitgestellt werden. Der Informationsfluss ist demnach als Qualitätsmerkmal und als Wirtschaftlichkeitsfaktor zu verstehen. Die Schnittstelle zwischen dem physischen Warenfluss und dem Informationsfluss auf EDV-Basis bildet die Identifikationstechnologien. In der Industrie verbreitete Identifikationstechnologien bestehen in der Regel aus einem Datenträger und einem Erfassungsgerät. Der Datenträger ist am physischen Objekt fixiert. Das Erfassungsgerät liest die auf dem Datenträger befindlichen Objektinformationen und wandelt sie in einen Binär-Code um, der durch nachgelagerte EDV weiterverarbeitet wird. Die momentan in der Industrie und im Handel am häufigsten verwendete Identifikationstechnologie ist der Barcode. In den letzten Jahren tritt die RFID-Technologie in den Fokus der Industrie und des Handels im Bereich Materialfluss und Logistik. Unter „Radio Frequency IDentification“ wird die Kommunikation per Funkwellen zwischen Datenträger (Transponder) und Lesegerät verstanden. Mittels der RFID-Technologie ist der Anwender, im Gegensatz zum Barcode, in der Lage, Informationen auf dem Transponder ohne Sichtkontakt zu erfassen. Eine Ausrichtung der einzelnen Artikel ist nicht erforderlich. Zudem können auf bestimmten Transpondertypen weitaus größere Datenmengen als auf einem Barcode hinterlegt werden. Transponder mit hoher Speicherkapazität eignen sich in der Regel, um die auf ihnen hinterlegten Daten bei Bedarf aktualisieren zu k��nnen. Eine dezentrale Datenorganisation ist realisierbar. Ein weiterer Vorteil der RFID-Technologie ist die Möglichkeit, mehrere Datenträger im Bruchteil einer Sekunde zu erfassen. In diesem Fall spricht man von einer Pulkerfassung. Diese Eigenschaft ist besonders im Bereich Warenein- und -ausgang von Interesse. Durch RFID ist es möglich, Ladeeinheiten, z. B. Paletten mit Waren, durch einen Antennenbereich zu fördern, und die mit Transpondern versehenen Artikel zu identifizieren und in die EDV zu übertragen. Neben der Funktionalität einer solchen Technologie steht in der Industrie vor allem die Wirtschaftlichkeit im Vordergrund. Transponder sind heute teuerer als Barcodes. Zudem müssen Investitionen in die für den Betrieb von RFID erforderliche Hard- und Software einkalkuliert werden. Daher muss der Einsatz der RFID-Technologie Einsparungen durch die Reorganisation der Unternehmensprozesse nach sich ziehen. Ein Schwachpunkt der RFID-Technologie ist momentan je nach Anwendung die mangelnde Zuverlässigkeit und Wiederholgenauigkeit bei Pulklesungen. Die Industrie und der Handel brauchen Identifikationstechnologien, deren Erfassungsrate im Bereich nahe 100 % liegt. Die Gefahr besteht darin, dass durch ein unzuverlässiges RFID-System unvollständige bzw. fehlerhafte Datensätze erzeugt werden können. Die Korrektur der Daten kann teurer sein als die durch die Reorganisation der Prozesse mittels RFID erzielten Einsparungen. Die Erfassungsrate der Transponder bei Pulkerfassungen wird durch mehrere Faktoren beeinflusst, die im Folgenden detailliert dargestellt werden. Das Institut für Fördertechnik und Logistik (IFT) in Stuttgart untersucht m��gliche Einflussgrößen auf die Erkennungsraten bei Pulkerfassungen. Mit den gewonnenen Erkenntnissen sollen mögliche Schwachstellen bei der Erkennung mehrerer Transponder im Vorfeld einer Implementierung in die Logistikprozesse eines Unternehmens eliminiert werden. With increasing complexity and variety of the logistics processes the significance of the used information technologies increases. The information accompanying the material flow is necessary in order to be able to identify goods and to be able to use corporate resources optimally. The classical goods entrance is to be mentioned as an example. The notification of amount and kind of incoming goods can be used for previously planning and providing of the personnel and necessary resources. The flow of information is to be understood accordingly as a high-quality feature and as an economic efficiency factor. With increasing complexity and variety of the logistics processes the significance of the used information technologies increases. The information accompanying the material flow is necessary in order to be able to identify goods and to be able to use corporate resources optimally. The classical goods entrance is to be mentioned as an example. The notification of amount and kind of incoming goods can be used for previously planning and providing of the personnel and necessary resources. The flow of information is to be understood accordingly as a high-quality feature and as an economic efficiency factor.

Distributed Control Nodes for Material Flow System Controls on the Example of Unit Load Conveyor and Sorter Facilities

The Chair of Transportation and Ware-housing at the University of Dortmund together with its industrial partner has developed and implemented a decentralized control system based on embedded technology and Internet standards. This innovative, highly flexible system uses autonomous software modules to control the flow of unit loads in real-time. The system is integrated into Chair’s test facility consisting of a wide range of conveying and sorting equipment. It is built for proof of concept purposes and will be used for further research in the fields of decentralized automation and embedded controls. This presentation describes the implementation of this decentralized control system.

System Architecture of a Mixed Reality Framework

In this paper the software architecture of a framework which simplifies the development of applications in the area of Virtual and Augmented Reality is presented. It is based on VRML/X3D to enable rendering of audio-visual information. We extended our VRML rendering system by a device management system that is based on the concept of a data-flow graph. The aim of the system is to create Mixed Reality (MR) applications simply by plugging together small prefabricated software components, instead of compiling monolithic C++ applications. The flexibility and the advantages of the presented framework are explained on the basis of an exemplary implementation of a classic Augmented Realityapplication and its extension to a collaborative remote expert scenario.

Developing and Deploying an XML-based Learning Content Management System at the FernUniversität Hagen

This paper is a report about the FuXML project carried out at the FernUniversität Hagen. FuXML is a Learning Content Management System (LCMS) aimed at providing a practical and efficient solution for the issues attributed to authoring, maintenance, production and distribution of online and offline distance learning material. The paper presents the environment for which the system was conceived and describes the technical realisation. We discuss the reasons for specific implementation decisions and also address the integration of the system within the organisational and technical infrastructure of the university.