Vaahdonestokemikaalin syöttötapahtuman tehostamisen vaikutus märkäosan toimintaan

An improved defoamer dosage procedure and a more efficient dosing point to the approach system were studied in this thesis. Their influence on paper machine wet end operations was investigated. The improved defoamer dosing procedure was examined at UMP-Kymmene Tervasaari PM8. Air content and its controlling methods at the paper machine were studied in the literature survey. Also the influence of dissolved gases and entrained air in the papermaking furnish were introduced. Feeding methods – a TrumpJet chemical mixer and traditional feeding devices – were reviewed. The defoamer’s functioning methods were studied. The influence of the use of defoamers was estimated based on the main selected wet end operations. In the experimental part, defoamer mixing with a traditional feeding method and two improved mixing stages were compared based on the air content profiles in PM8’s approach system. The reference dosage procedure was PM8’s old dosing system. The first dosage procedure in the comparison involved two TrumpJet chemical mixers installed on the bottom wire trays. The second element of comparison involved the improvement brought by a third TrumpJet chemical mixer installed on the top wire tray. This second comparison of the efficient defoamer feeding concept was made at a higher production speed of PM8. The air content control situation was also studied at the higher production speed. In addition the connection between the defoamer and air content was observed and a mill-scale system was studied. The economical benefits of the new dosing procedure were also reviewed. Air content profiles of short circulation were measured in the reference situation and the two comparison points of the study. These air content measurements proved the main gas load is introduced to PM8's paper furnish from the white water tray. Thick stock air content was not essential when the air volume flow was considered. The improved defoamer dosing procedure made lower dosage amounts possible. Compared with the traditional feeding system, the new defoamer feeding concept made only few direct improvements to the wet end operations and the produced paper itself. The lower defoamer need was noticed to have a positive influence on hydrophobic sizing and paper defects. The surfaces of the white water tanks and the operation of pumps were assessed based on the density variations of the suspension. The temperature in the white water silo was stated to have a significant influence on the air content measured in the first centrifugal cleaning stage.

Welding of Sheet metal using Modified short arc MIG/MAG welding process

In this research work, the results of an investigation dealing with welding of sheet metals with diverse air gap using FastROOT modified short arc welding method and short circuit MAG welding processes have been presented. Welding runs were made under different conditions and, during each run, the different process parameters were continuously monitored. It was found that maximum welding speed and less HAZ are reached under specific welding conditions with FastROOT method with the emphasis on arc stability. Welding results show that modified short arc exhibits a higher electrode melting coefficient and with virtually spatter free droplet transition. By adjusting the short circuit duration the penetration can be controlled with only a small change in electrode deposition. Furthermore, by mixing pulsed MIG welding with modified arc welding the working envelope of the process is greatly extended allowing thicker material sections to be welded with improved weld bead aesthetics. FastROOT is a modified short arc welding process using mechanized or automated welding process based on dip transfer welding, characterized by controlled material deposition during the short circuit of the wire electrode to the workpiece.

Sistema aquoso bifásico: uma alternativa eficiente para extração de íons

Solvent extraction has been successfully applied to metal ion preconcentration and often meant the use of toxic organic diluents. However, regulatory pressure is increasingly focusing on the use and disposal of organic solvents, and thus the development of nonhazardous alternatives is important. In this review, we examine the application of aqueous biphasic systems (ABS) to extraction of ions, analyzing their potential and limitations and suggest that ABSs could be an efficient substitute for oil/water biphasic systems. ABSs are formed by mixing certain inorganic salts and water-soluble polymers, or by mixing two water-soluble polymers.

Kemikaalisekoituksen vaikutus kartongin liimausasteen pienimittakaavaiseen vaihteluun

Tässä diplomityössä tutkittiin massaliimauksen stabiilisuutta kartonkikoneella ja himan sekoituskonseptin muuttamisen vaikutusta liimausasteeseen ja liimausasteen pienimittakaavaiseen vaihteluun konerullan sisällä. Koeajoista saadut tulokset olivat erittäin lupaavia. Koeajoissa annosteltiin hartsia kahdella eri TrumpJet™-installaatiolla. Ensimmäisessä koeajossa hartsi sekoitettiin kaikkiin kolmeen kerrokseen sakean massan syöttölinjaan, ennen pyörrepuhdistuksen vaatimaa laimennusta. Toisessa koeajossa hartsi annosteltiin kolmella TrumpJet-suuttimella kartongin pintakerrokseen konesihdin jälkeen ja muihin kerroksiin perinteisesti sekoitussäiliön. Tuloksista nähtiin, että hartsin syöttö perälaatikon lähestymisvirtaukseen on mahdollista kartongin laadun ja liimausasteen siitä karsimatta. Liimausaste määritettiin Stora Enson spesifisen REP-menetelmän (raw edge penetration) avulla. Koesarjojen välille ei syntynyt merkittäviä eroja reunaimeytymätasoihin, eikä koesarjojen sisäisiin vaihteluihin verrattaessa referensikonerulliin.

Full instability behavior of N-dimensional dynamical systems with a one-directional nonlinear vector field

We show how certain N-dimensional dynamical systems are able to exploit the full instability capabilities of their fixed points to do Hopf bifurcations and how such a behavior produces complex time evolutions based on the nonlinear combination of the oscillation modes that emerged from these bifurcations. For really different oscillation frequencies, the evolutions describe robust wave form structures, usually periodic, in which selfsimilarity with respect to both the time scale and system dimension is clearly appreciated. For closer frequencies, the evolution signals usually appear irregular but are still based on the repetition of complex wave form structures. The study is developed by considering vector fields with a scalar-valued nonlinear function of a single variable that is a linear combination of the N dynamical variables. In this case, the linear stability analysis can be used to design N-dimensional systems in which the fixed points of a saddle-node pair experience up to N21 Hopf bifurcations with preselected oscillation frequencies. The secondary processes occurring in the phase region where the variety of limit cycles appear may be rather complex and difficult to characterize, but they produce the nonlinear mixing of oscillation modes with relatively generic features

Determinação do teor de edta remanescente em soluções de limpeza de equipamentos industriais

Cleaning solutions containing EDTA are widely employed to remove incrustation despite of the costs involved. The free content of EDTA in commercial solutions may be determined by mixing an aliquot to ammonium oxalate and using a standard calcium solution as titrant. The end-point is detected by the formation of insoluble calcium oxalate after all EDTA is complexed. A system for turbidimetric detection of the end-point was envisaged to substitute the visual detection, which impaired the analyses of dark samples. The proposed method was tested with real samples and good accuracy and precision was obtained.

Obtenció d'estruvita a partir de la fracció líquida digerida de purins de vaca

Actualment a Catalunya existeixen zones amb importants limitacions per l’aplicació de purins al sòl, pel que és imprescindible trobar alternatives de gestió i tractament que permetin l’aprofitament adequat dels recursos continguts a les dejeccions ramaderes sense afectar el medi. La digestió anaeròbia és una de les tècniques utilitzades en el tractament de les dejeccions ramaderes. L’efluent líquid que s’obté d’aquest tractament no modifica el contingut de nitrogen i fòsfor i per tant ha de ser gestionat correctament. L’objectiu general d’aquest projecte és avaluar la precipitació d’estruvita (sal de magnesi, amoni i fosfat) com una alternativa de gestió de l’efluent líquid d’una planta de digestió anaeròbia i compostatge que tracta dejeccions ramaderes conjuntament amb altres residus orgànics. S’han avaluat els efectes dels diferents paràmetres operacionals en la formació d’estruvita (pH, temperatura, velocitat d’agitació, alcalinitat), mitjançant assaigs en discontinu amb solució sintètica. A continuació s’ha procedit a obtenir estruvita a partir de la fracció líquida digerida de purí (FLD), en assaigs en discontinu per estudiar l’efecte del contingut de matèria orgànica i sòlids Totals (ST), així com el contingut en fosfats i el pH de reacció. Finalment, s’han optimitzat els paràmetres de procés en continu, mitjançant la posada en marxa d’un reactor a escala de laboratori i estudi de l’efecte de la velocitat d’agitació i de la introducció del stripping de CO2, tant amb solució sintètica com amb la fracció líquida digerida del purí. Dels resultats obtinguts es pot concloure que els factors que tenen una major influència en el procés d’obtenció d’estruvita són el pH (el pH òptim es situa al voltant de 9), i la presència de matèria orgànica i sòlids ens suspensió, que interfereix de forma quantitativa i qualitativa en la formació de l’estruvita. En el procés en continu s’ha aconseguit reduccions d’un 84% i 98% d’amoni i fòsfor respectivament, obtenintse estruvita que pot ser utilitzada com a fertilitzant d’alliberació lenta. Es pot concloure que la precipitació d’estruvita és una bona alternativa per millorar la gestió de les dejeccions ramaderes alhora que permet recuperar nutrients i tancar cicles. La combinació amb un tractament previ que elimini la matèria orgànica, com podria ser la digestió anaeròbia, i una separació de fases, per eliminar els sòlids en suspensió, es presenta com una configuració amb molts avantatges.

The Impact of Aspen and Alder on the Quality of NHBK

The purpose of this work was to study the effect of aspen and alder on birch cooking and the quality of the pulp produced. Three different birch kraft pulps were studied. As a reference, pure aspen and alder were included. The laboratory trials were done at the UPM Research Centre in Lappeenranta, Finland. The materials used were birch, aspen and alder mill chips that were collected around the area of South-Carelia in Finland. The chips used in the study were pulped using a standard kraft process. The pulps including birch fibres were ECF-bleached at laboratory scale to a target brightness of 85 %. The bleached pulps were beaten at low consistency by a laboratory Voith Sulzer refiner and tested for optical and physical properties. The theoretical part is a study of hardwoods that takes into accounts the differences between birch, aspen and alder. Major sub-areas were fibre and paper-technical properties as well as chemical composition and their influence on the different properties. The pulp properties of birch, aspen and alder found in previous studies were reported. Russian hardwood forest resources were also investigated. The fundamentals of kraft pulping and bleaching were studied at the end of theoretical part. The major effect of replacing birch with aspen and alder was the deterioration (lowering) of tensile and tear strengths. In other words, addition of aspen and alder to a birch furnish reduced strength properties. The reinforcement ability of the tested pulps was the following: 100 % birch > 80 % birch, 20 % aspen > 70 % birch, 20 % aspen, 10 % alder. The second thing noted was that blending of birch together with aspen and alder give better smoothness, optical properties and also formation. It can be concluded, that replacement of birch with alder during cooking by more than 10 % can negatively affect on the paper-technical properties of birch pulp. Mixing pure birch and aspen pulps would be more beneficial when producing printing paper made from chemical pulp.

Demonstrando os fundamentos, potencialidades e limitações da análise por injeção seqüencial

The sensitivity and accuracy of sequential injection methods are dependent on efficient overlapping of reagent and sample zones as they are propelled toward the detector cell. The formation of the reduced phosphomolybdic acid is used to demonstrate that the overlapping efficiency in a fixed reaction coil relies on a suitable choice of reagent to sample volume ratio. Additionally, under poor mixing conditions or highly concentrated samples, the reaction extension is strongly dependent on the reagent concentration. The zone-sampling concept is exploited to determine phosphate in cola-based soft drinks after in-line dilution in an auxiliary coil.

An experimental and theoretical study of multiphase flow in a circulating fluidized bed

A systematic averaging procedure has been derived in order to obtain an integral form of conservation equations for dispersed multiphase flow, especially applicable to fluidized beds. A similar averaging method is applied further to formulate macroscopic integral equations, which can be used in one-dimensional and macroscopic multi dimensional models. Circulating fluid bed hydrodynamics has been studied experimentally and both macroscopic and microscopic flow profiles have been measured in a cold model. As an application of the theory, the one dimensional model has been used to study mass and momentum conservation of gas and solid in a circulating fluid bed. Axial solid mixing has also been modelled by the one dimensional model and mixing parameters have been evaluated.

Ikääntyvät työelämässä. Päihittääkö nuoruus ja koulutus aikuisuuden ja kokemuksen?

The Ageing in Working Life. Do Adolescence and Schooling Beat Adulthood and Experience? This study examines the changes in the work and the work organisations of employees in the fields of health care and retail trade who have turned 45 and their experience of change. In addition, the question of how ageing employees experience their status in post-modern working life is explored. Attention is also focused on the choices and decisions connected with staying at work and retiring. These views are examined in relation to professions and professional cultures. Thematic interviews (N=98) were used to gather the material. The effects of the market liberalistic turn in welfare policy are clearly seen in the everyday work of the health care professions. These changes were examined from the point of view of managing by outcomes and quality assurance, multi-professional cooperation, flexibility in the division of labour, and the spread of market-like procedures. The discourse of those in involved retail trade was dominated by extremely tight global market competition and control of outcomes, and by the structural changes taking place in the retail trade sector. This change discourse was to a large extent a reaction to those changes in the functional environment which were experienced as negative and to the conflict between their own professional identity and professional ethics on the one hand, and their functional environment on the other. There were also obstacles connected with professional culture: defending one's own station and power, guarding the 'frontier', showed up in attitudes towards new management and organisation models or towards structural and functional reforms. The deep structures of professional culture and the mindset of the actors change much more slowly than the functional practices of organisations. For those in a supervisory position, the loss of power due to becoming part of a chain or because of the introduction of a team organisation model was not an easy thing to accept. The nurses and others in related fields felt that they were forced to do work that was below their level of training and professional skill. For sales personnel and those who did assisting work in health care, power and the possibility of having an influence were not so important, as long as they were able to do their work in their own way and were trusted. This view is often completely forgotten, for example, in various organisation models in which power and the possibility of having an influence entwined with power are taken for granted as being clearly positive and desired aspects of job satisfaction. Up to date professional skills were experienced as being important from the point of view of professional identity and self-worth. Thus, training can be understood as a moral obligation, which in turn is intertwined with professional ideology. In the rhetoric of adult education, an adult is expected to be an active player who will seek training again and again if working life so requires. The dark side of this ideology, which leads to feelings of guilt, was apparent in the thoughts of the respondents. Am I never good enough at my job; why must I continually strive for better, additional qualifications? The majority of the respondents evaluated their expertise as being at quite a high level. This self-confidence did not extend to applying for a job. Job recruitment was seen as a situation in which age discrimination reached its peak. The interviewees were unanimous about the idea that society favours the young. Especially among those in the retail trade sector, there was a feeling that it would be difficult, if not impossible, to find a new job of the same level or a permanent post if they were made redundant. Age discrimination was also apparent in the retail trade field in the form of older employees being retired against their will or transferred to other tasks. It was felt that ruthless forced retirement of older workers was part of the personnel policy of some organisations. The importance of one's outward appearance was connected with the theme of discrimination. This phenomenon is described using the concept of the double standard of ageing in feminist research. An ageing woman is relegated to an inferior position due to both her age and her sex. A culture that would both make possible and allow various types of choices regardless of age, which is described as being characteristic of the post-modern era, does not seem to be very topical in the practice of working life. It is important for employees that the management and the personnel policy that is being implemented makes them feel like both their contribution and they as individuals are appreciated, that their opinions are listened to and that they are noticed as persons. The interviewees hoped for gratitude and a concern for the well-being of employees that shows in everyday life. They valued training and activities aimed at maintaining their work ability, but thought that better coping at work and a pleasant working environment cannot be achieved through such measures as along as the foundation is 'in a mess'. Development of the quality of working life is the only thing that can improve job satisfaction and get people to remain in the work force longer than at present. There should be a sufficient number of properly trained employees at the work place. It was important to the respondents that they be able to stay on their job to the end with honour, since compromising with their own quality standards or acting contrary to their ideal self-image in terms of professional ethics would strike a blow to their professional self-esteem. They called for the development of various types of workplace flexibility, and felt that they have the right to a lightened workload and to early retirement. Early retirement was even seen as an altruistic deed: it would free up a place for younger workers. Thoughts of retirements were explained by familiar factors such as health and finances, life situation, the enticement of free-time, as well as by various factors related to work. It is very important to ageing employees that their work has meaningful content. The values related to self-fulfilment are felt to be of great importance, and if they cannot be realised at work, the respondents wanted more free time, either through retirement or in the form of flexibility in working life.

The influence of crystallization conditions on the filtration characteristics of sulphathiazole suspensions

Cooling crystallization is one of the most important purification and separation techniques in the chemical and pharmaceutical industry. The product of the cooling crystallization process is always a suspension that contains both the mother liquor and the product crystals, and therefore the first process step following crystallization is usually solid-liquid separation. The properties of the produced crystals, such as their size and shape, can be affected by modifying the conditions during the crystallization process. The filtration characteristics of solid/liquid suspensions, on the other hand, are strongly influenced by the particle properties, as well as the properties of the liquid phase. It is thus obvious that the effect of the changes made to the crystallization parameters can also be seen in the course of the filtration process. Although the relationship between crystallization and filtration is widely recognized, the number of publications where these unit operations have been considered in the same context seems to be surprisingly small. This thesis explores the influence of different crystallization parameters in an unseeded batch cooling crystallization process on the external appearance of the product crystals and on the pressure filtration characteristics of the obtained product suspensions. Crystallization experiments are performed by crystallizing sulphathiazole (C9H9N3O2S2), which is a wellknown antibiotic agent, from different mixtures of water and n-propanol in an unseeded batch crystallizer. The different crystallization parameters that are studied are the composition of the solvent, the cooling rate during the crystallization experiments carried out by using a constant cooling rate throughout the whole batch, the cooling profile, as well as the mixing intensity during the batch. The obtained crystals are characterized by using an automated image analyzer and the crystals are separated from the solvent through constant pressure batch filtration experiments. Separation characteristics of the suspensions are described by means of average specific cake resistance and average filter cake porosity, and the compressibilities of the cakes are also determined. The results show that fairly large differences can be observed between the size and shape of the crystals, and it is also shown experimentally that the changes in the crystal size and shape have a direct impact on the pressure filtration characteristics of the crystal suspensions. The experimental results are utilized to create a procedure that can be used for estimating the filtration characteristics of solid-liquid suspensions according to the particle size and shape data obtained by image analysis. Multilinear partial least squares regression (N-PLS) models are created between the filtration parameters and the particle size and shape data, and the results presented in this thesis show that relatively obvious correlations can be detected with the obtained models.

Supercritical CO2 recovery of caffeine from green coffee oil: new experimental solubility data and modeling

The caffeine solubility in supercritical CO2 was studied by assessing the effects of pressure and temperature on the extraction of green coffee oil (GCO). The Peng-Robinson¹ equation of state was used to correlate the solubility of caffeine with a thermodynamic model and two mixing rules were evaluated: the classical mixing rule of van der Waals with two adjustable parameters (PR-VDW) and a density dependent one, proposed by Mohamed and Holder² with two (PR-MH, two parameters adjusted to the attractive term) and three (PR-MH3 two parameters adjusted to the attractive and one to the repulsive term) adjustable parameters. The best results were obtained with the mixing rule of Mohamed and Holder² with three parameters.

Cardiotocógrafo: monitor para el control de la frecuencia cardiaca fetal y la dinámica uterina

Controlar la frecuencia cardiaca fetal y la dinámica uterina durante el proceso del embarazo y el parto resulta de particular importancia para conocer el estado de salud de la madre y el niño. Hoy en día existen aparatos muy novedosos para este fin de uso generalizado en los hospitales españoles. De este tema se ocupa la Ficha de Utillaje de este mes analizando en qué consiste este monitor; cómo se utiliza, los pasos a seguir; etc.

Cardiotocógrafo: monitor para el control de la frecuencia cardiaca fetal y la dinámica uterina

Controlar la frecuencia cardiaca fetal y la dinámica uterina durante el proceso del embarazo y el parto resulta de particular importancia para conocer el estado de salud de la madre y el niño. Hoy en día existen aparatos muy novedosos para este fin de uso generalizado en los hospitales españoles. De este tema se ocupa la Ficha de Utillaje de este mes analizando en qué consiste este monitor; cómo se utiliza, los pasos a seguir; etc.