TCA Evaluation : Lab Measurements, Modelling and System Simulations

The study reported here is part of a large project for evaluation of the Thermo-Chemical Accumulator (TCA), a technology under development by the Swedish company ClimateWell AB. The studies concentrate on the use of the technology for comfort cooling. This report concentrates on measurements in the laboratory, modelling and system simulation. The TCA is a three-phase absorption heat pump that stores energy in the form of crystallised salt, in this case Lithium Chloride (LiCl) with water being the other substance. The process requires vacuum conditions as with standard absorption chillers using LiBr/water. Measurements were carried out in the laboratories at the Solar Energy Research Center SERC, at Högskolan Dalarna as well as at ClimateWell AB. The measurements at SERC were performed on a prototype version 7:1 and showed that this prototype had several problems resulting in poor and unreliable performance. The main results were that: there was significant corrosion leading to non-condensable gases that in turn caused very poor performance; unwanted crystallisation caused blockages as well as inconsistent behaviour; poor wetting of the heat exchangers resulted in relatively high temperature drops there. A measured thermal COP for cooling of 0.46 was found, which is significantly lower than the theoretical value. These findings resulted in a thorough redesign for the new prototype, called ClimateWell 10 (CW10), which was tested briefly by the authors at ClimateWell. The data collected here was not large, but enough to show that the machine worked consistently with no noticeable vacuum problems. It was also sufficient for identifying the main parameters in a simulation model developed for the TRNSYS simulation environment, but not enough to verify the model properly. This model was shown to be able to simulate the dynamic as well as static performance of the CW10, and was then used in a series of system simulations. A single system model was developed as the basis of the system simulations, consisting of a CW10 machine, 30 m2 flat plate solar collectors with backup boiler and an office with a design cooling load in Stockholm of 50 W/m2, resulting in a 7.5 kW design load for the 150 m2 floor area. Two base cases were defined based on this: one for Stockholm using a dry cooler with design cooling rate of 30 kW; one for Madrid with a cooling tower with design cooling rate of 34 kW. A number of parametric studies were performed based on these two base cases. These showed that the temperature lift is a limiting factor for cooling for higher ambient temperatures and for charging with fixed temperature source such as district heating. The simulated evacuated tube collector performs only marginally better than a good flat plate collector if considering the gross area, the margin being greater for larger solar fractions. For 30 m2 collector a solar faction of 49% and 67% were achieved for the Stockholm and Madrid base cases respectively. The average annual efficiency of the collector in Stockholm (12%) was much lower than that in Madrid (19%). The thermal COP was simulated to be approximately 0.70, but has not been possible to verify with measured data. The annual electrical COP was shown to be very dependent on the cooling load as a large proportion of electrical use is for components that are permanently on. For the cooling loads studied, the annual electrical COP ranged from 2.2 for a 2000 kWh cooling load to 18.0 for a 21000 kWh cooling load. There is however a potential to reduce the electricity consumption in the machine, which would improve these figures significantly. It was shown that a cooling tower is necessary for the Madrid climate, whereas a dry cooler is sufficient for Stockholm although a cooling tower does improve performance. The simulation study was very shallow and has shown a number of areas that are important to study in more depth. One such area is advanced control strategy, which is necessary to mitigate the weakness of the technology (low temperature lift for cooling) and to optimally use its strength (storage).

Brytmånens utformning vid trädfällning - Jämförande studier av böjmotstånd och gångjärnseffekt : Designing felling hinge in tree felling - Comparative studies of bending resistance and hinge effect

Vid trädfällning med motorsåg sparar man en så kallad brytmån som skall fungera som ett gång¬järn när trädet fälls. Om brytmånen går av tidigt finns en risk att trädet faller okontrolle¬rat. De rekommendationer som finns säger att brytmånens bredd skall göras proportionell mot trädets diameter. Genom att teoretiskt och praktiskt undersöka vilka krafter brytmånen utsätts för och vad den håller för har det varit möjligt att dra vissa slutsatser om hur en bra brytmån skall se ut. Ett viktigt resultat är att en bred brytmån (över 30-40 mm) är mycket trög att böja och inte fungerar i det avseendet att den går av redan vid små böjningar. Teoretiska be¬räkningar och praktiska försök visar att en relativt smal brytmån håller för belastningen vid rakt motlut även på stora träd. Som ny rekommendationen föreslås att brytmånens bredd inte bör vara mer än 30 mm. Av försöken kan man också dra slutsatsen att frusen ved är stel och brister tidigt, varför svår¬fällda träd inte bör fällas när veden är fryst.A felling hinge is used when felling trees by help of chain saw. If the hinge breaks early in the fall of the tree there is a great risk that the tree will fall without control. Present recommenda¬tions in Sweden say that the thickness of the felling hinge shall be made in proportion to the stem diameter. By use of theoretical and practical examinations of the forces stressing the felling hinge, and the strength of the wood itself, it has been possible to draw conclusions regarding the correct design of a felling hinge. One important result is that a thick felling hinge (over 30-40 mm) is very hard to bend and does not work well as it looses most of its strength already at a small forward bending angel. Theoretical calculations and practical tests show that a relatively narrow felling hinge will manage very well the forces when felling trees with lean opposite to the felling direction even for large trees. Our new recommendation is that the thickness of the felling hinge in normal Swedish conditions should not exceed 30 mm. Through the studies it can also be seen that frozen, brittle wood breaks at small bending angels. For that reason particularly difficult trees not should be felled when the wood is frozen.

Borlänge and Falun Brundtland cities

Development of an infrastructure for Brundtland Renewable Energy Network - BREN is a European Commission Alterner Project with Contract no XVII/4. 1030/Z96-032.The project has its origin in the UN-report “Our Common Future”, 1989. A change in and reduction of the use of energy was fundamental in order to reach the goals which the report proposed. Denmark decided on an action plan on how energy consumption could be reduced “Energi 2000 - Handlingsplan för en bäredygtig udvikling”. The ministries of energy in Denmark and Schleswig Holstein both agreed to start an energy saving project in a smaller town. The project was called “Brundtlandby” and the two first were Toftlund in South Jutland and Bredstedt in North Friesland. After a short period a further two German Cities, Rheinsberg and Viernheim, and Rajec in Slovakia joined the group. A network for the exchange of knowledge and experience between the cities was formed. The network, Brundtland City Project, inspired the participating cities in the continuing work with energy saving measures. The Brundtland City Project was presented at an international conference “Cities and Energy” in Trondheim, Norway,in December 1995. Great interest was shown in the project and it was decided that a network should be developed in northern European countries as a pilot project to be enlarged with other European countries later on. A steering committee was formed with representatives from the nordic countries.An application was sent to the European Commission, Alterner Program, and was approved in Juli 1996. The project was subdivided into nine activities. Activity 1, consisted of summarising the experiences of the Brundtland City Project in Toftlund, Denmark and the Brundtland Cities network in Slovakia, Germany and Denmark. The Scandinavian part started with Activity 2, to engage municipalities/cities in Finland, Norway and Sweden in the project. The Solar Energy Research Center, SERC, Högskolan Dalarna was appointed as co-ordinator for the Swedish part. The project was presented at a seminar on the 30th September for representatives from the municipalities of Borlänge and Falun. On the 10th of December 1996 the two municipalities accepted the invitation to join the Northern network. Pelle Helje, Borlänge Energi, has been informant for the municipality of Borlänge and Anders Goop, Department of Urban Planninginformant for the municipality of Falun with Jan Kaans, Estates department providing information to the basis for the Newsletter.Reports on the work in Borlänge and Falun municipalities have been made to Brundtland Center Denmark on three occasions; Activities 2-5, 16-12-1997, Activities 6-7, including parts of activities 8-9, 03-03-1998, and the basis for the Newsletter, 01-07-1998. The Nordic reports have been compiled at the Brundtland Center Denmark for submission to the European Commission. English has been the common language. After the report of activities 2 - 5 the participants wereinvited to a project meeting and a workshop at Brundtland Center the 23rd and 24th March 1998.This was the first occasion the participants in the project met and the network thus took a moreconcrete form. It also was decided that the next meeting should be in Borlänge in August 1998,with Borlänge Energi and Solar Energy Research Center SERC as organisers. As BrundtlandCentre Denmark was wound up for financial reasons, the project meeting in Borlänge wascancelled.Compilation of the Final Report was carried out by Esbensen Consultants in October 1998Future development of the networkIt is intended to continue the work with the Brundtland City Network as an “EU Thermie Bproject”and the network will be enlarged with the addition of four new Brundtland Cities from Austria, Germany, Italy and Great Britain. In addition the village of Putja in Estonia will join the network but this will be financed by the EU-Phare programme.

Provningsmetod för integrerade sol-biosystem : Årsverkningsgrad genom korttidsmätning

Test method for integrated solar- biomass systems - Long term prediction trough short term measurementsSP Technical Research Institute of Sweden and SERC, Dalarna University have in cooperation developed a test method for integrated solar and biomass systems. The test method is performed under six days including two summer days, two winter days and two spring/autumn days true to real weather conditions and loads for a single family house. The aim of the test method is to get information about a Combisystem’s annual performance and operation throughout a short term test. Seven different solar Combisystems have been tested within the project together with a pellet boiler without solar collectors. In addition to that a comparative testing has been performed at the two laboratories at SP and at SERC on the same Combisystem. The test method developed within the project has been proved to withstand the aim of the project, which is to be able to compare the performance between the systems. The test method is also suitable for identification of possible operation problems so they can be taken care of and consequently improves the system.The project and the system testing reveal that it is in general favorable to combine biomass pellets with solar heating. Pellet boilers has normally a low performance during the summer period but combined with a solar collector the boiler can be switch off during this period. There are however big differences in performance between the tested. The efficiency of the pellet boiler is highly dependent of the operating conditions and elements like heat losses from the system, system configuration and control strategy have great influence of the performance of the system and the emissions. On the other hand, the performance and the size of the solar collectors have a minor effect on the overall system performance. There is obviously a big potential for improvement of the system´s performance and the developed test method is an essential way to implement this perfection.

Skriftpraktiker i gymnasieskolan : Bygg- och omvårdnadselever skriver

Literacy Practices in Upper Secondary School. The Writing of Construction and Health CarePupilsThe aim of the dissertation is to demonstrate and explain the place and function writing has in allsubjects in two vocational classes in a Swedish upper secondary school. The material has beencollected through ethnographic field studies in construction and health care classes over one schoolyear. The material consists of literacy events, where pupils write, and the context of situation andtext are noted.In theoretical terms the study takes a discourse analysis perspective, where writing is seen fromwithin different frames. Writing is analysed based on an ideological view of literacy inspired byNew Literacy Studies using the context of situation and text with the aim of describing differentliteracy practices in both classes.The material was classified into three different situation types, two school-initiated and one nonschool-initiated. The first school-initiated situation type is orally-governed, the second writinggoverned,while it is less clear how the non-school-initiated type is inspired.In the writing situations we investigate the writing activities that are used, while texts areanalysed based on text acitivites. Writing and text activities are used together to explain the writingcompetences that are used in the writing situations.The conclusions are that writing gets little space and attention in both classes. The healthcare class writes in more situations and also writes longer texts than the construction class.Literacy practices differ between the classes. The health care class demonstrates one schoolgovernedwriting practice, while the construction class moves between two different schoolgovernedpractices. The literacy practices in the construction class are similar to the writing usagethat can be found at a building site. Writing is used in both classes mainly to structure and storeknowledge.The non-school-governed material also shows differences between the classes. Here too morewriting takes place in the health care class. The function of the non-school-governed writing is tocommunicate and inform through writing.

Mellan frihet och kontroll : Om läroplanskonstruktioner i svensk skola

The aim of this thesis is to explore how different competing discourses in the historical context of the Swedish education development have qualified and disqualified different constructions of national curriculum. How and after what kind of principles is the curriculum constructed? What qualify who are going to be recognized as the author and addressee of the curriculum? These key ques-tions of the study are discussed in the first part of the thesis. My point of depar-ture is that the curriculum can be understood as a relation between freedom and control. In an educational system this relationship reflects the problematic ten-sion between the external demands from an authoritative center and the local need to independently reflect over educational issues. How these concepts are defined by the prevailing social discourses affect specific relations and construc-tions of curricula as a steering tool and a producer of specific teacher identities. In this sense, I claim that curriculum is constructed in different ways depending on which of the didactic questions are emphasized and answered and who is judged as the legitimate author. Based on this, three models of curriculum con-struction are formulated; the content based, the result based and the process based. These models are subsequently used as an analytical tool to examine the historical development of Swedish national curricula. The second part of the thesis investigates the Swedish education system and the production of the national curriculum as a product of rival discourses. The historical investigation begins 1842 when the first state curriculum was issued and the inquiry concludes in 2008. The findings indicate that no one single con-struction has been totally dominant and that there has been an on-going discur-sive struggle between different alternative and opinions about what teachers must do and be.

Skolutveckling som diskursiv praktik : Några ideologiska implikationer

This study aims at highlighting the ideological implications of school development as a discursive practice. More comprehensively the aim is also contributing to rearrangements and shifts in perspective when school development is the matter. One of today´s most widespread and dominant discourses are said to be the one which concerns development, and according to many interpreters, development is one of the most prominent commandments in the modern as well as the post-modern narratives. School development as a concept has for the last 15 years established itself firmly in both Swedish school policy and in Swedish school research. It may sound obvious and commendable but also such axioms may be questioned.The design of the study lies in the field of discourse research and more specifically within critical discursive psychology, which draws on both a post-structural and a postmodern conception of discourse. The study is based on the idea that the ideological potential of arguments occurs, develops and changes in discursive practices and not anywhere else or at any abstract level. The starting point is a perception that certain issues and topics within e.g. conversation, depending on time and context will be seen as controversial, while others will be taken for granted.One part of the basis of the study consists of texts with a direct bearing on a specific school research and development project which took place between 2003 and 2008. Participating partners in the collaboration were the Swedish National Agency for School Improvement, Karlstad University, Dalarna University and 13 municipalities in Sweden. Another part of the basis of the study consists of texts in which ‘school development’ is considered and negotiated in more general terms, usually without reference to the project. All texts derive from the period 2003 – 2006.The analysis shows that school development as discursive practice often rely on a set of stereotypical expressions and ways of arguing. Stereotypes, which among other things, tend to divide people into suitable and non-suitable, capable and non-capable, which may be regarded as a somewhat unexpected implication of school development. The material has been dramatized by an intrigue inspired by the sociologist Zygmunt Bauman´s texts. He has written extensively on the modern in relation to the postmodern and about the ambivalence which resides in between and school development as discursive practice can be understood in much the similar way.

Translation, Communication and 'Learning' : Experiences from teaching a master program in Viet Nam

In Vietnam, as in other Asian countries, co-operation with foreign universities plays an important role for the development of higher education. This paper is based on personal experiences from teaching a Swedish Master Programme in Education Science at Vietnam National University in Hanoi. Using theories developed by Lev Vygotsky and Donald Schon, the programme is explored as an inter-cultural learning process. Three aspects are focused upon. Firstly, the fact that communication between students and teachers is conducted with the help of translators who support both teachers and students in their attempt to understand and make themselves understood. Secondly, the expressed need to connect the ideas and techniques which are studied in the programme to the students´ professional worlds. Thirdly, the need to construct a framework wherein the students can inquire into their own situations and to encourage them to try new and more productive ways to deal with problems they are confronted with.

Typografiska riktlinjer och textframställning för smartphones

Idag använder allt fler människor sina smartphones för att surfa och använda tjänster online. Detta innebär att en stor del text läses på små skärmar. Detta arbete handlar om hur text bäst utformas och struktureras för att enklast kunna läsas och uppfattas på en mobilskärm. Faktorer som berörs är typgrad, ljusrum, textlängd, teckensnittsklass, radlängd, bild i text och kontrastverkan. Arbetet utgår från en normativ, svensk person utan funktionsnedsättningar. Arbetet är grundat på litteratur, egna analyser, intervjuer med branschfolk, enkätundersökning och test med fokusgrupp. Resultatet blev att en text på smartphone bäst utformas med flera styckesindelningar i form av blankrader, med bilder där bilden tillför något i informativt syfte och textlängd baserat på ämneskategori. Bilden bör sättas ovanför brödtexten. Längre texter ska sättas med scrollfunktion. Kontrast har stor betydelse på mobiltelefoner, texter går bra att läsa även när de är satta negativt. Teckensnittsklass är enligt resultatet av denna rapport inte av betydelse. Både seriff och sanserif kan läsas utan problem på smartphones. Typgraden bör förstoras något i förhållande till telefonens default-inställningar. På grund av att text på skärm inte stödjer avstavningar rekommenderas korta ord där det är möjligt för att förhindra en allt för hackig högerkant.

Kinesiska affärsetableringar i Sverige : Kartläggning över områden som förbättrar chanserna att lyckas

Aim and starting point: The aim of the Bachelor thesis is to examine and define the paramount knowledge Chinese businessmen need in order to succeed with their establishment in Sweden. The authors also seek to answer what incentives attract Chinese businessmen to come to Sweden, as well as how Chinese establishments in Sweden can be predicted to appear in the future. Results/conclusions: The study outlines key areas in which Chinese businessmen should have knowledge in order to succeed with their establishment in Sweden. The results also gives an indication on how Chinese business establishments in Sweden will appear in the future, into which areas the Chinese mainly invest/establish in, as well as why and how these are done. On the basis of this material the authors generate proposals for educational packages which among others can be sold to Chinese businessmen. Knowledge overview: Here relevant theory connected to the area of study is presented. The knowledge overview presents the Swedish in relation to the Chinese perspective in areas such as: culture, hierarchy, relations, Face, communication, HRM, education, CSR and labour law. The knowledge overview can itself contribute to fostering an understanding of differences between Sweden and China. Method: The area of research has been accessed by a combination of methods. The study is both deductive and explorative. The main channel of information and data collection are in-depth interviews which are used as a deductive starting point, an expert investigation and as a Grounded Theory. As a complement the authors have also conducted a delphi study in which an expert panel answered questions concerning the future of Chinese establishments in Sweden. The deductive and explorative parts have been analyzed individually and have each generated a conclusion. These conclusions have then been interwoven in a synthesis that highlights and creates new knowledge.

”Vi måste träna på språket hela tiden precis som man måste göra om man vill bli duktig på fotboll” : Pedagogers syn på att arbeta med elever som har svenska som andraspråk

Syftet med denna studie är att få en inblick i hur pedagoger som arbetar i grundskolans senare år upplever hur det är att arbeta med elever som har svenska som andraspråk, och vilka svårigheter som kan uppstå. Undersökningen genomfördes med kvalitativa intervjuer på en skola i mellersta Sverige. De intervjuade i studien är totalt fyra stycken: en SVA-lärare, en NO-lärare och två SO-lärare. Resultatet visar att samtliga lärare är medvetna om att det är viktigt att arbeta med språket även i ämnesundervisnigen, men olika faktorer gör att det är svårt att genomföra detta i praktiken. Dessa faktorer är: tidsbrist, stora nivåskillnader mellan eleverna och att det saknas kompetens hos ämneslärarna inom området svenska som andraspråk. Slutligen kan man ej förvänta sig att de intervjuade pedagogerna och andraspråkseleverna som de undervisar ska vara representanter för hela Sveriges skolor, då undersökningen endast genomförts på en skola med fyra intervjuer med pedagoger.

Improved Road Design for Future Maintenance - Analysis of Road Barrier Repair Costs

The cost of a road construction over its service life is a function of the design, quality of construction, maintenance strategies and maintenance operations. Unfortunately, designers often neglect a very important aspect which is the possibility to perform future maintenance activities. The focus is mainly on other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This licentiate thesis is a part of a Ph.D. project entitled “Road Design for lower maintenance costs” that aims to examine how the life-cycle costs can be optimized by selection of appropriate geometrical designs for the roads and their components. The result is expected to give a basis for a new method used in the road planning and design process using life-cycle cost analysis with particular emphasis on road maintenance. The project started with a review of literature with the intention to study conditions causing increased needs for road maintenance, the efforts made by the road authorities to satisfy those needs and the improvement potential by consideration of maintenance aspects during planning and design. An investigation was carried out to identify the problems which obstruct due consideration of maintenance aspects during the road planning and design process. This investigation focused mainly on the road planning and design process at the Swedish Road Administration. However, the road planning and design process in Denmark, Finland and Norway were also roughly evaluated to gain a broader knowledge about the research subject. The investigation was carried out in two phases: data collection and data analysis. Data was collected by semi-structured interviews with expert actors involved in planning, design and maintenance and by a review of design-related documents. Data analyses were carried out using a method called “Change Analysis”. This investigation revealed a complex combination of problems which result in inadequate consideration of maintenance aspects. Several urgent needs for changes to eliminate these problems were identified. Another study was carried out to develop a model for calculation of the repair costs for damages of different road barrier types and to analyse how factors such as road type, speed limits, barrier types, barrier placement, type of road section, alignment and seasonal effects affect the barrier damages and the associated repair costs. This study was carried out using a method called the “Case Study Research Method”. Data was collected from 1087 barrier repairs in two regional offices of the Swedish Road Administration, the Central Region and the Western Region. A table was established for both regions containing the repair cost per vehicle kilometre for different combinations of barrier types, road types and speed limits. This table can be used by the designers in the calculation of the life-cycle costs for different road barrier types.

Road Design for Future Maintenance : Life-cycle Cost Analyses for Road Barriers

The cost of a road construction over its service life is a function of design, quality of construction as well as maintenance strategies and operations. An optimal life-cycle cost for a road requires evaluations of the above mentioned components. Unfortunately, road designers often neglect a very important aspect, namely, the possibility to perform future maintenance activities. Focus is mainly directed towards other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This doctoral thesis presents the results of a research project aimed to increase consideration of road maintenance aspects in the planning and design process. The following subgoals were established: Identify the obstacles that prevent adequate consideration of future maintenance during the road planning and design process; and Examine optimisation of life-cycle costs as an approach towards increased efficiency during the road planning and design process. The research project started with a literature review aimed at evaluating the extent to which maintenance aspects are considered during road planning and design as an improvement potential for maintenance efficiency. Efforts made by road authorities to increase efficiency, especially maintenance efficiency, were evaluated. The results indicated that all the evaluated efforts had one thing in common, namely ignorance of the interrelationship between geometrical road design and maintenance as an effective tool to increase maintenance efficiency. Focus has mainly been on improving operating practises and maintenance procedures. This fact might also explain why some efforts to increase maintenance efficiency have been less successful. An investigation was conducted to identify the problems and difficulties, which obstruct due consideration of maintainability during the road planning and design process. A method called “Change Analysis” was used to analyse data collected during interviews with experts in road design and maintenance. The study indicated a complex combination of problems which result in inadequate consideration of maintenance aspects when planning and designing roads. The identified problems were classified into six categories: insufficient consulting, insufficient knowledge, regulations and specifications without consideration of maintenance aspects, insufficient planning and design activities, inadequate organisation and demands from other authorities. Several urgent needs for changes to eliminate these problems were identified. One of the problems identified in the above mentioned study as an obstacle for due consideration of maintenance aspects during road design was the absence of a model for calculating life-cycle costs for roads. Because of this lack of knowledge, the research project focused on implementing a new approach for calculating and analysing life-cycle costs for roads with emphasis on the relationship between road design and road maintainability. Road barriers were chosen as an example. The ambition is to develop this approach to cover other road components at a later stage. A study was conducted to quantify repair rates for barriers and associated repair costs as one of the major maintenance costs for road barriers. A method called “Case Study Research Method” was used to analyse the effect of several factors on barrier repairs costs, such as barrier type, road type, posted speed and seasonal effect. The analyses were based on documented data associated with 1625 repairs conducted in four different geographical regions in Sweden during 2006. A model for calculation of average repair costs per vehicle kilometres was created. Significant differences in the barrier repair costs were found between the studied barrier types. In another study, the injuries associated with road barrier collisions and the corresponding influencing factors were analysed. The analyses in this study were based on documented data from actual barrier collisions between 2005 and 2008 in Sweden. The result was used to calculate the cost for injuries associated with barrier collisions as a part of the socio-economic cost for road barriers. The results showed significant differences in the number of injuries associated with collisions with different barrier types. To calculate and analyse life-cycle costs for road barriers a new approach was developed based on a method called “Activity-based Life-cycle Costing”. By modelling uncertainties, the presented approach gives a possibility to identify and analyse factors crucial for optimising life-cycle costs. The study showed a great potential to increase road maintenance efficiency through road design. It also showed that road components with low investment costs might not be the best choice when including maintenance and socio-economic aspects. The difficulties and problems faced during the collection of data for calculating life-cycle costs for road barriers indicated a great need for improving current data collecting and archiving procedures. The research focused on Swedish road planning and design. However, the conclusions can be applied to other Nordic countries, where weather conditions and road design practices are similar. The general methodological approaches used in this research project may be applied also to other studies.

Viljan till fysisk aktivitet : En intervention avsedd att stimulera ungdomar att bli fysiskt aktiva

Jenny Isberg (2009): Viljan till fysisk aktivitet – en intervention avsedd att stimulera ungdomar att bli fysiskt aktiva. Örebro Studies in Sport Sciences 6, 141 pp. Physical education (PE) at school may play an important role in the process of becoming physically active in the adolescence and in developing a physically active lifestyle. The opportunities for teachers to provide positive physical activity experiences to the student population extend regularly over the school terms. For some students, PE can be the only opportunity they have to be physically active. Therefore it is important that the students become motivated to practice physical activity and know the purpose with physical activity. The overall purpose of this dissertation was to investigate the possibilities to motivate youth, 12-16 years old, to practice physical activity and hopefully to stimulate them to continue to be physically active in young adulthood. The sample consisted of 122 Swedish compulsory school students (12-16 years old), 51 girls and 71 boys, who were either physically inactive, physically active but not formal members of sport clubs, or physically active and members of a sport club. They used a self-monitoring instrument to describe their physical activity and we compared their self-reported physical activity with their actual VO2 capacity and physical status. The self-monitoring instrument was further validated against an activity monitor, RT3. The intervention lasted one and a half years, and four to five years later a follow-up study was done. Using a quasi-experimental design, the three groups of participants were compared with youths who did not use the self-monitoring instrument. The main findings were that the associations between the accelerometer counts and the activities the students recorded in the self-monitoring instrument were high. The participants  in Group 1 (physically inactive) continued exercising nearly to the same extent as during the intervention while youths in a matched control group did not develop regular physical activity habits. Concerning Group 2 (exercisers), participants in the intervention group were more physically active both during the intervention and at follow-up, compared with a matched control group of exercisers who did not use the self-monitoring instrument. In Group 3 (sport team members), there was no difference between the intervention group and a matched control group after the intervention or at follow-up.  The conclusion of these main findings was that when someone motivates students to continue being physically active and to change their physical activity patterns in a positive direction, the self-monitoring instrument can be a door-opener for youths who are physically inactive or regularly active outside sports clubs.

Äldre texter - didaktik och motivation : Didaktisering av ett 1500-talsepos

Syftet med detta arbete är att undersöka huruvida vissa didaktiska tillvägagångssätt kan öka motivationen hos gymnasieelever inför studier av äldre texter samt i vilken utsträckning valfrihet och medbestämmande är viktigt inför arbetet med dessa. Könsrelaterade jämförelser görs. Tidigare forskning presenteras och en empirisk kvantitativ undersökning med enkäter genomförs, baserad på SCAS (Swedish Core Affect Scale) i reducerad form. Ett 1500-talsepos presenteras medelst olika didaktiska metoder för elever som löpande noterar graden av motivation på en niogradig skala bestående av adjektivpar.Studien visar att vissa didaktiska tillvägagångssätt ökar elevers motivation. Berättande samt rörliga bilder i kombination med tal och musik visar sig vara de mest stimulerande metoderna, gärna anknytning till universella teman och perspektiv. Studien visar även att endast vissa elever upplever valfrihet och medbestämmande i samband med arbetet med texten som något positivt.