On the mechanism of the formation of horizontal cracks in a vertical column of saturated sand

Extended horizontal cracks have! been observed experimentally in a vertical column of saturated sand when a flow of water is forced to percolate upward through it. This paper provides a theory for this phenomenon. It will be shown that the presence of inhomogeneity in permeability along the length of the column is essential for such cracks to develop. It will also be shown that small initial inhomogeneity may be magnified through the transport of the finer component of the sand by percolation. Under certain conditions liquefaction takes place at a section of the sand column causing a crack to initiate and grow there. This theory is found to be in good qualitative agreement with the experimental findings.

Formation of nanoparticles from ultrafast laser condensates of metal targets

Optimised ultrafast laser ablation can result in almost complete ionisation of the target material and the formation of a high velocity plasma jet. Collisions with the ambient gas behind the shock front cools the material resulting in the formation of mainly spherical, single crystal nanoscale particles in the condensate. This work characterises the nanoscale structures produced by the ultrafast laser interactions in He atmospheres at STP with Ni and Al. High resolution transmission electron microscopy was employed to study the microstructure of the condensates and to classify the production of particles forms as a function of the illumination conditions.

Growth of highly-quality single-wall carbon nanotubes without amorphous carbon formation

A simple way to deposit single-wall carbon nanotubes by CVD without the co-deposition of unwanted a-C was demonstrated. It was found that the catalytic deposition of SWCNTs occurs at a substantial rate compared to the self-pyrolysis of the hydrocarbon gas used.

Efecto de un carbón no activado en el desarrollo de terneros durante la crianza artificial

Resumen: Las terneras de reposición son las unidades productivas futuras del tambo. Su desarrollo va a tener un impacto en la rentabilidad de la actividad, no sólo porque las terneras enfermas pueden perder potencial productivo futuro, sino también porque retrasarán su ingreso al tambo, incrementando los costos de reposición. Uno de los mayores riesgos de la crianza artificial es la alta probabilidad de existencia de diarreas durante el primer mes de vida de los terneros. El objetivo de este trabajo fue evaluar el uso de un carbón no activado en la ganancia diaria de peso y en la incidencia de diarreas de terneras de tambo criadas artificialmente. El ensayo se realizó con 63 terneras de 3 a 100 días de edad. Se tomaron los pesos a diferentes edades y los datos se analizaron con un modelo de regresión no lineal del tipo exponencial. La presencia de diarreas se evalúo por observación positiva y su incidencia se midió mediante una prueba de comparación de proporciones (Chi2). Los resultados demostraron que para ambas variables no se encontraron diferencias significativas entre el grupo control y el grupo tratado. La tasa de crecimiento resultante del modelo estimado de regresión no lineal fue de 0,0140 y 0,0142 para el grupo control y tratamiento respectivamente, con un solapamiento de los intervalos de confianza. En lo que respecta a la incidencia de diarreas, el número de animales afectados fue similar en ambos grupos, por lo que se infiere que no existe correlación entre el uso del producto y la prevalencia de la enfermedad. Se concluye que, para las condiciones de este ensayo, el agregado del carbón a la dieta líquida del ternero no tiene efectos sobre la ganancia diaria de peso ni sobre la incidencia de diarreas en terneros

Las técnicas de fecundación artificial en el proyecto del Código Civil : manipulación genética y responsabilidad médica

Introducción: Uno de los grandes temas en discusión en 2012 por parte de la doctrina jurídica argentina ha sido la presentación ante el Congreso Nacional del “Proyecto de Reforma, Unificación y Actualización de los Códigos Civil y Comercial de la Nación”. Así las cosas, varias son las voces que se han alzado tanto a favor de la reforma como en su contra. Mientras que algunos consideran que la legislación proyectada implica un avance en materia de derechos humanos, llegando a tildarla como la “reforma más participativa de la historia”1; otros se apartan de esta idea y ven en el Proyecto grandes deficiencias. En el presente trabajo intentaremos analizar uno de los artículos más polémicos de la reforma: el Artículo 19, referente al comienzo de la existencia de la persona humana. Mas no habremos de agotar nuestra investigación allí, proseguiremos analizando otro artículo que puede pasar inadvertido pero que conlleva grandes implicancias si se analiza a la luz del 19. Hacemos referencia al Artículo 57, el cual trata acerca de las prácticas destinadas a alterar la constitución genética de la descendencia. Por último, buscaremos ver qué implicancias puede generar este panorama respecto de la responsabilidad de los profesionales de la salud.

Experiments and Lagrangian simulations on the formation of droplets in continuous mode

Experimental and computational studies on the dynamics of millimeter-scale cylindrical liquid jets are presented. The influences of the modulation amplitude and the nozzle geometry on jet behavior have been considered. Laser Doppler anemometry (LDA) was used in order to extract the velocity field of a jet along its length, and to determine the velocity modulation amplitude. Jet shapes and breakup dynamics were observed via shadowgraph imaging. Aqueous solutions of glycerol were used for these experiments. Results were compared with Lagrangian finite-element simulations with good quantitative agreement. © 2011 The American Physical Society.

Modelling soot formation in a DISI engine

In this work, the formation of soot in a Direct Injection Spark Ignition (DISI) engine is simulated using the Stochastic Reactor Model (SRM) engine code. Volume change, convective heat transfer, turbulent mixing, direct injection and flame propagation are accounted for. In order to simulate flame propagation, the cylinder is divided into an unburned, entrained and burned zone, with the rate of entrainment being governed by empirical equations but combustion modelled with chemical kinetics. The model contains a detailed chemical mechanism as well as a highly detailed soot formation model, however computation times are relatively short. The soot model provides information on the morphology and chemical composition of soot aggregates along with bulk quantities, including soot mass, number density, volume fraction and surface area. The model is first calibrated by simulating experimental data from a Gasoline Direct Injection (GDI) Spark Ignition (SI) engine. The model is then used to simulate experimental data from the literature, where the numbers, sizes and derived mass particulate emissions from a 1.83 L, 4-cylinder, 4 valve production DISI engine were examined. Experimental results from different injection and spark timings are compared with the model and the qualitative trends in aggregate size distribution and emissions match the exhaust gas measurements well. © 2010 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Experiments and Lagrangian simulations on the formation of droplets in drop-on-demand mode

The creation and evolution of millimeter-sized droplets of a Newtonian liquid generated on demand by the action of pressure pulses were studied experimentally and simulated numerically. The velocity response within a model, large-scale printhead was recorded by laser Doppler anemometry, and the waveform was used in Lagrangian finite-element simulations as an input. Droplet shapes and positions were observed by shadowgraphy and compared with their numerically obtained analogues. © 2011 American Physical Society.

On the Formation of Periodic Segmentation Cracks in a Coating Plated on a Substrate with Periodic Subsurface Inclusions

The mechanism of the formation of periodic segmentation cracks of a coating plated on a substrate with periodic subsurface inclusions (PSI) is investigated. The internal stress in coating and subsequently the strain energy release rate (SERR) of the segmentation cracks are computed with finite element method (FEM). And the effect of the geometrical parameters of the PSI is studied. The results indicate that the ratio of the width of the inclusion to the period of the repeated structure has an optimum value, at which the maximum internal tensile stress and SERR arise. On the other hand, the ratio of the max-thickness of the inclusion to the thickness of the coating has a threshold value, above which the further increase of this ratio should seldom influence the internal stress or the SERR.

Population of nonnative states of lysozyme variants drives amyloid fibril formation.

The propensity of protein molecules to self-assemble into highly ordered, fibrillar aggregates lies at the heart of understanding many disorders ranging from Alzheimer's disease to systemic lysozyme amyloidosis. In this paper we use highly accurate kinetic measurements of amyloid fibril growth in combination with spectroscopic tools to quantify the effect of modifications in solution conditions and in the amino acid sequence of human lysozyme on its propensity to form amyloid fibrils under acidic conditions. We elucidate and quantify the correlation between the rate of amyloid growth and the population of nonnative states, and we show that changes in amyloidogenicity are almost entirely due to alterations in the stability of the native state, while other regions of the global free-energy surface remain largely unmodified. These results provide insight into the complex dynamics of a macromolecule on a multidimensional energy landscape and point the way for a better understanding of amyloid diseases.

GROOVE FORMATION AND INTERACTION DURING ABRASION OF COPPER.

A pin on cylinder wear rig has been built with precision stepping motor drives to both rotary and axial motions which enable accurate positional control to be achieved. Initial experiments using sapphire indenters running against copper substrates have investigated the build up of a single wear groove by repeated sliding along the same track. An approximate three dimensional ploughing analysis is also presented and the results of theory and experiment compared.

Pattern formation and spatial solitons in bistable liquid-crystal microcavities

We report on spatial pattern formation, and appearances of 'optical bullet holes' in single-mode microcavities that are filled with liquid-crystals, when pumped above the cavity resonance frequency. These phenomena only occur beyond the bistability threshold. ©2002 Optical Society of America.

In situ formation by laser cladding of a TiC composite coating with a gradient distribution

An in situ method was developed to produce an Ni alloy composite coating reinforced by in situ reacted TiC particles with a gradient distribution, using one-step laser cladding with a pre-placed powder mixture on a 5CrMnMo steel substrate. Dispersed and ultra-fine TIC particles were formed in situ in the coating. Most. of the TiC particles, with a marked gradient distribution, were uniformly distributed within interdendritic regions because of the trapping effect of the advancing solid-liquid interface. In addition, the TiC-gamma-Ni interfaces generated in situ were found to be free from any deleterious surface reaction. Finally, the microhardness also showed a gradient variation, with the highest value of 1250 Hv0.2 and the wear properties of the coating were significantly enhanced.