Esterificação de ácidos graxos utilizando zircônia sulfatada e compósitos carvão ativado/zircônia sulfatada como catalisadores

In this work sulfated zirconia (SZr) and activated carbon/SZr composites produced by impregnation method with or without heating treatment step (CABC/SZr-I and CABC/SZr-I SC) and by the method of synthesis of SZr on the carbon (CABC/SZr-S) was used as catalysts in the esterification reactions of fatty acids. The SZr presented very active, conversions higher than 90% were obtained after 2 h of reaction. The activity of the composite CABC/SZr-I20%SC was up to 92%, however, this was directly related to time and temperature reactions. CABC/SZr-I and CABC/SZr-S were less active in esterification reactions, what could be attributed to its low acidity

Produção e caracterização de espumas cerâmicas obtidas a partir de lodo de anodização de alumínio

Ceramic foams were produced from a sludge generated in the aluminum anodizing process by using an industrial polyurethane foam (replication method) with open cell sizes of 10 ± 5 ppi (porosity = 97%) which were impregnated with suspensions containing 50-61 wt.% alumina, 1 wt.% citric acid, 6 wt.% bentonite and fired at 1600 ºC for 2 h. The aluminum anodizing sludge shows a high alumina content (87.5 wt.%) and a low particle size (~1.7 mm) after calcination and milling. The obtained filters show porosity of approximately 70%, filtration capability (mass water flow) of 1.7 kg/s and mechanical strength under compression of 2.40 MPa.

Modification of the performance of WO3-ZrO2 catalysts by metal addition in hydrocarbon reactions

A study of the different hydrocarbon reactions over Ni doped WO3-ZrO2 catalysts was performed. Ni was found as NiO at low Ni concentration while at high Ni concentrations a small fraction was present as a metal. For both cases, Ni strongly modified total acidity and concentration of strong acid sites. In the cyclohexane dehydrogenation reaction, Ni addition promotes both benzene and methyl cyclopentane production. The hydroconversion activity (n-butane and n-octane) increases with the augment of total acidity produced by Ni. The selectivity to reaction products is modified according to the acid strength distribution changes produced by Ni addition.

Síntese e caracterização de CaZrO3 e BaZrO3 nanoestruturados

In this work, nanostructured samples of barium zirconate (BaZrO3) and calcium zirconate (CaZrO3) were synthesized by the gel-combustion method, using glycine as fuel. The ceramic powders were calcined at 550 °C for 2 h and subsequently heat treated at 1350 °C for 10 min (fast-firing). The X-ray diffraction technique was employed to identify and characterize the crystalline phases present in the synthesized powders, using the Rietveld method. Monophasic nanostructured samples of BaZrO3 and CaZrO3 presenting average crystallite sizes of around 8.5 and 10.3 nm, respectively, were found after fast-firing.

APLICAÇÃO DE ÓXIDOS DE FERRO NANOESTRUTURADOS COMO ADSORVENTES E FOTOCATALISADORES NA REMOÇÃO DE POLUENTES DE ÁGUAS RESIDUAIS

New techniques for treating wastewater, particularly the removal or degradation of organic pollutants and heavy metals, among other pollutants, have been extensively studied. The use of nanostructured iron oxides as adsorbent and photocatalyst for the removal of these contaminants has proved a promising approach, not only because of their high treatment efficiency, but also for their cost-effectiveness, having the flexibility for in situ and ex situ applications. In this review, we briefly introduced the most used kinds of iron oxide nanoparticles, some synthesis techniques for iron oxide nanostructure formation, their potential benefits in environmental clean-up, and their recent advances and applications in wastewater treatment. These advances range from the direct applications of synthesized nanoparticles as adsorbents for removing toxic contaminants or as catalysts to oxidize and break down noxious contaminants (including bacteria and viruses) in wastewater, to integrating nanoparticles into conventional treatment technologies, such as composite photocatalytic filters (membranes, sand and ceramic) that combine separation technology with photocatalytic activity. Finally, the impact of nanoparticles on the environment and human health is briefly discussed.

SYNGAS PRODUCTION FROM CO2-REFORMING OF CH4 OVER SOL-GEL SYNTHESIZED Ni-Co/Al2O3-MgO-ZrO2 NANOCATALYST: EFFECT OF ZrO2 PRECURSOR ON CATALYST PROPERTIES AND PERFORMANCE

Ni-Co/Al2O3-MgO-ZrO2 nanocatalyst with utilization of two different zirconia precursors, namely, zirconyl nitrate hydrate (ZNH) and zirconyl nitrate solution (ZNS), was synthesized via the sol-gel method. The physiochemical properties of nanocatalysts were characterized by XRD, FESEM, EDX, BET and FTIR analyses and employed for syngas production from CO2-reforming of CH4. XRD patterns, exhibiting proper crystalline structure and homogeneous dispersion of active phase for the nanocatalyst ZNS precursor employed (NCAMZ-ZNS). FESEM and BET results of NCAMZ-ZNS presented more uniform morphology and smaller particle size and consequently higher surface areas. In addition, average particle size of NCAMZ-ZNS was 15.7 nm, which is close to the critical size for Ni-Co catalysts to avoid carbon formation. Moreover, FESEM analysis indicated both prepared samples were nanoscale. EDX analysis confirmed the existence of various elements used and also supported the statements made in the XRD and FESEM analyses regarding dispersion. Based on the excellent physiochemical properties, NCAMZ-ZNS exhibited the best reactant conversion across all of the evaluated temperatures, e.g. CH4 and CO2 conversions were 97.2 and 99% at 850 ºC, respectively. Furthermore, NCAMZ-ZNS demonstrated a stable yield with H2/CO close to unit value during the 1440 min stability test.

KINETIC STUDY OF SELECTIVE GAS-PHASE OXIDATION OF ISOPROPANOL TO ACETONE USING MONOCLINIC ZRO2 AS A CATALYST

Zirconia was prepared by a precipitation method and calcined at 723 K, 1023 K, and 1253 K in order to obtain monoclinic zirconia. The prepared zirconia was characterized by XRD, SEM, EDX, surface area and pore size analyzer, and particle size analyzer. Monoclinic ZrO2 as a catalyst was used for the gas-phase oxidation of isopropanol to acetone in a Pyrex-glass-flow-type reactor with a temperature range of 443 K - 473 K. It was found that monoclinic ZrO2 shows remarkable catalytic activity (68%) and selectivity (100%) for the oxidation of isopropanol to acetone. This kinetic study reveals that the oxidation of isopropanol to acetone follows the L-H mechanism.

MATERIAIS VÍTREOS E LUZ: PARTE 2

In this second part it will be discussed some photonic applications of glassy and glass ceramic thin films which can be used as planar waveguides. Some photonic applications require certain specifications of glass, which can be quantified by studying the nonlinear optical properties of the materials. Therefore, a brief introduction of these phenomena is discussed, as well as the use of femtosecond lasers to manipulate the composition or for the preparation of waveguides into glasses. Finally, the article will address a brief introduction on microstructured optical fibers and commercial application prospects for these devices.

Surface Modification of Ceramics

Ceramics are widely used in industrial applications due to their advantageous thermal and mechanical stability. Corrosion of ceramics is a great problem resulting in significant costs. Coating is one method of reducing adversities of corrosion. There are several different thin film deposition processes available such as sol-gel, Physical and Chemical Vapour Deposition (PVD and CVD). One of the CVD processes, called Atomic Layer Deposition (ALD) stands out for its excellent controllability, accuracy and wide process capability. The most commonly mentioned disadvantage of this method is its slowness which is partly compensated by its capability of processing large areas at once. Several factors affect the ALD process. Such factors include temperature, the grade of precursors, pulse-purge times and flux of precursors as well as the substrate used. Wrongly chosen process factors may cause loss of self-limiting growth and thus, non-uniformities in the deposited film. Porous substrates require longer pulse times than flat surfaces. The goal of this thesis was to examine the effects of ALD films on surface properties of a porous ceramic material. The analyses applied were for permeability, bubble point pressure and isoelectric point. In addition, effects of the films on corrosion resistance of the substrate in aqueous environment were investigated. After being exposured to different corrosive media the ceramics and liquid samples collected were analysed both mechanically and chemically. Visual and contentual differences between the exposed and coated ceramics versus the untreated and uncoated ones were analysed by scanning electron microscope. Two ALD film materials, dialuminium trioxide and titanium dioxide were deposited on the ceramic substrate using different pulse times. The results of both film materials indicated that surface properties of the ceramic material can be modified to some extent by the ALD method. The effect of the titanium oxide film on the corrosion resistance of the ceramic samples was observed to be fairly small regardless of the pulse time.

Pinnoiteteollisuudessa syntyvien maalijätteiden hyötykäyttö ja uudet liiketoimintamahdollisuudet

Tämän diplomityön tavoite on kartoittaa maalien ja lakkojen valmistuksessa syntyvien sivuvirtojen hyötykäyttöä ja hyötykäyttöpotentiaalia nykyisellään. Työn tarkoitus on toimia esiselvityksenä pinnoiteteollisuuden sivuvirtojen hyötykäyttöön liittyvien liiketoimintamahdollisuuksien syvemmälle analyysille. Teollisuuden sivuvirtoihin liittyvää tietoa kerätään tilastoista ja olemassa olevista raporteista sekä haastattelemalla teollisuus- ja palveluyritysten edustajia sekä alan asiantuntijoita. Sivuvirtojen teknisten hyötykäyttömahdollisuuksien ja liiketoiminnallisten mahdollisuuksien tarkastelua varten järjestetään työpajoja asiantuntijoille Apila Group Oy Ab:n asiantuntijaverkostossa. Neljässä haastatellussa tuotantolaitoksissa syntyi vuonna 2008 yhteensä 6 662 tonnia kiinteää jätettä ja lietteitä. 68 % näistä sivuvirroista hyötykäytettiin energiana tai polttoaineen valmistuksessa. Materiaalina sivuvirtoja hyötykäytettiin 16 % sivuvirroista, pääasiassa pahvia, paperia, metalleja sekä tynnyreitä ja kontteja. Myös merkittävä osa liuottimista otettiin talteen uudelleenhyödyntämistä varten. Tässä diplomityössä hyötykäyttömahdollisuuksien tarkempaa tarkastelua varten valittiin tavanomaisiksi jätteiksi luokiteltuja maalisivuvirtoja, joita haastatelluissa tuotantolaitoksissa syntyi noin 1 500 tonnia. Maalisivuvirtojen tärkeimmät materiaaliominaisuudet liittyvät niiden sisältämiin täyte- ja sideaineisiin, jotka muodostavat merkittävän osan maalien koostumuksesta. Selvityksen mukaan nämä ominaisuudet voidaan ottaa hyötykäyttöön erilaisissa yhdistelmämateriaaleissa, esimerkiksi ekstruusiopuristetuissa tai ahtopuristetuissa muovikuitukomposiiteissa. Komposiittien raaka-aineena käytetään jo erilaisia sivuvirtoja ja lisäksi erilaisten komposiittien markkinoiden ennustetaan kasvavan. Tämä voi tarjota mahdollisuuksia uusille palvelu-, t&k- tai tuotteistusliiketoiminnoille. Kuivilla maalijätteillä on myös hyvä lämpöarvo, jolloin energiahyötykäytön ja palamisjäännöksen materiaalihyötykäytön yhdistäminen mm. keramiikka- tai sementtiteollisuudessa voi tarjota mahdollisuuksia uusille liiketoiminnoille.

Muotia, mukavuutta ja mielipiteitä. Kaakeliuuni yhteiskunnallisten muutosten ilmentäjänä keskiajan ja uuden ajan alun Suomessa

Fashion, Comf ort and Conviction is a study investigating the adoption and significance of the ceramic tile stove in medieval and early modern Finland. It presents stove tiles found in archaeological excavations, places the tiles in their cultural contexts and examines them as indicators of various social changes. The early history of the ceramic tile stove goes back to the 12th century in the German-speaking Alpine regions, from where it spread to the Baltic Sea region during the Middle Ages. On the basis of the archaeological finds presented in this study, the introduction of the tile stove in Finland dates to the early 15th century. Its adoption was connected to the increase in foreign trade links and social emulation, the demand for comfort, and innovations in building technology and interior design. Stove tiles also reflect the political and religious convictions of their time and open a fascinating window on everyday life in medieval and early modern Finland.

Physiological responses of caprines raised under different types of covering

Thermal discomfort inside facilities is one of the factors responsible for low productivity of caprines in the Brazilian Northeast region, because inadequate weather conditions can cause elevated rectal temperature, increased respiratory rate, decreased food ingestion and reduced production. The present paper aimed to study the behavior of physiological thermoregulation of the animals (respiratory rate - RR and rectal temperature - RT) at four different times of the day (8 a.m., 11 a.m., 2 p.m. and 5 p.m.) and their relation to bioclimatic indexes (Temperature Humidity Index - THI, Black Globe Humidity Index - BGHI and Radiant Heat Load - RHL) in order to determine whether the type of covering used in the animals facilities (ceramic covering - CC, asbestos cement covering - AC and straw covering - SC) interferes with the physiology of thermoregulation. The time of data collection was related to the values of environmental and physiological variables. At 2 p.m. it was found the highest values of Radiant Heat Load on the three types of covering. The values of RT and RR were higher at 11 a.m. and 2 p.m., and the straw tile provided better thermal conditions of microclimate for the animals. The increased RR maintained the caprines homeothermy.

Evaluation of roof slope and exposure with different roofing materials in reduced models of animal production facilities in spring and summer

The present study was conducted at the Department of Rural Engineering and the Department of Animal Morphology and Physiology of FCAV/Unesp, Jaboticabal, SP, Brazil. The objective was to verify the influence of roof slope, exposure and roofing material on the internal temperature of reduced models of animal production facilities. For the development of the research, 48 reduced and dissemble models with dimensions 1.00 × 1.00 × 0.50 m were used. The roof was shed-type, and the models faced to the North or South directions, with 24 models for each side of exposure. Ceramic, galvanized-steel and fibro tiles were used to build the roofs. Slopes varied between 20, 30, 40 and 50% for the ceramic tile and 10, 30, 40 and 50% for the other two. Inside the models, temperature readings were performed at every hour, for 12 months. The results were evaluated in a general linear model in a nested 3 × 4 × 2 factorial arrangement, in which the effects of roofing material and exposure were nested on the factor Slope. Means were compared by the Tukey test at 5% of probability. After analyzing the data, we observed that with the increase in the slope and exposure to the South, there was a drop in the internal temperature within the model at the geographic coordinates of Jaboticabal city (SP/Brazil).

Software for design of experiments and response modelling of cake ltration applications

Filtration is a widely used unit operation in chemical engineering. The huge variation in the properties of materials to be ltered makes the study of ltration a challenging task. One of the objectives of this thesis was to show that conventional ltration theories are di cult to use when the system to be modelled contains all of the stages and features that are present in a complete solid/liquid separation process. Furthermore, most of the ltration theories require experimental work to be performed in order to obtain critical parameters required by the theoretical models. Creating a good overall understanding of how the variables a ect the nal product in ltration is somewhat impossible on a purely theoretical basis. The complexity of solid/liquid separation processes require experimental work and when tests are needed, it is advisable to use experimental design techniques so that the goals can be achieved. The statistical design of experiments provides the necessary tools for recognising the e ects of variables. It also helps to perform experimental work more economically. Design of experiments is a prerequisite for creating empirical models that can describe how the measured response is related to the changes in the values of the variable. A software package was developed that provides a ltration practitioner with experimental designs and calculates the parameters for linear regression models, along with the graphical representation of the responses. The developed software consists of two software modules. These modules are LTDoE and LTRead. The LTDoE module is used to create experimental designs for di erent lter types. The lter types considered in the software are automatic vertical pressure lter, double-sided vertical pressure lter, horizontal membrane lter press, vacuum belt lter and ceramic capillary action disc lter. It is also possible to create experimental designs for those cases where the variables are totally user de ned, say for a customized ltration cycle or di erent piece of equipment. The LTRead-module is used to read the experimental data gathered from the experiments, to analyse the data and to create models for each of the measured responses. Introducing the structure of the software more in detail and showing some of the practical applications is the main part of this thesis. This approach to the study of cake ltration processes, as presented in this thesis, has been shown to have good practical value when making ltration tests.

Software for design of experiments and response modelling of cake filtration applications

Filtration is a widely used unit operation in chemical engineering. The huge variation in the properties of materials to be ltered makes the study of ltration a challenging task. One of the objectives of this thesis was to show that conventional ltration theories are di cult to use when the system to be modelled contains all of the stages and features that are present in a complete solid/liquid separation process. Furthermore, most of the ltration theories require experimental work to be performed in order to obtain critical parameters required by the theoretical models. Creating a good overall understanding of how the variables a ect the nal product in ltration is somewhat impossible on a purely theoretical basis. The complexity of solid/liquid separation processes require experimental work and when tests are needed, it is advisable to use experimental design techniques so that the goals can be achieved. The statistical design of experiments provides the necessary tools for recognising the e ects of variables. It also helps to perform experimental work more economically. Design of experiments is a prerequisite for creating empirical models that can describe how the measured response is related to the changes in the values of the variable. A software package was developed that provides a ltration practitioner with experimental designs and calculates the parameters for linear regression models, along with the graphical representation of the responses. The developed software consists of two software modules. These modules are LTDoE and LTRead. The LTDoE module is used to create experimental designs for di erent lter types. The lter types considered in the software are automatic vertical pressure lter, double-sided vertical pressure lter, horizontal membrane lter press, vacuum belt lter and ceramic capillary action disc lter. It is also possible to create experimental designs for those cases where the variables are totally user de ned, say for a customized ltration cycle or di erent piece of equipment. The LTRead-module is used to read the experimental data gathered from the experiments, to analyse the data and to create models for each of the measured responses. Introducing the structure of the software more in detail and showing some of the practical applications is the main part of this thesis. This approach to the study of cake ltration processes, as presented in this thesis, has been shown to have good practical value when making ltration tests.