Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Modeling of residual stresses and distortion due to welding in fillet welds

Welding has a growing role in modern world manufacturing. Welding joints are extensively used from pipes to aerospace industries. Prediction of welding residual stresses and distortions is necessary for accurate evaluation of fillet welds in relation to design and safety conditions. Residual stresses may be beneficial or detrimental, depending whether they are tensile or compressive and the loading. They directly affect the fatigue life of the weld by impacting crack growth rate. Beside theoretical background of residual stresses this study calculates residual stresses and deformations due to localized heating by welding process and subsequent rapid cooling in fillet welds. Validated methods are required for this purpose due to complexity of process, localized heating, temperature dependence of material properties and heat source. In this research both empirical and simulation methods were used for the analysis of welded joints. Finite element simulation has become a popular tool of prediction of welding residual stresses and distortion. Three different cases with and without preload have been modeled during this study. Thermal heat load set is used by calculating heat flux from the given heat input energy. First the linear and then nonlinear material behavior model is modeled for calculation of residual stresses. Experimental work is done to calculate the stresses empirically. The results from both the methods are compared to check their reliability. Residual stresses can have a significant effect on fatigue performance of the welded joints made of high strength steel. Both initial residual stress state and subsequent residual stress relaxation need to be considered for accurate description of fatigue behavior. Tensile residual stresses are detrimental and will reduce the fatigue life and compressive residual stresses will increase it. The residual stresses follow the yield strength of base or filler material and the components made of high strength steel are typically thin, where the role of distortion is emphasizing.

The pH-dependent phase distribution of wood pitch components in papermaking processes

Wood contains only a very small amount of lipophilic extractives, commonly known as wood pitch. The pitch is known to cause severe problems in papermaking processes. The amount of pitch in process waters can be decreased by seasoning of the raw material prior to pulping, pulp washing, removal of pitch by flotation, adsorption of pitch onto various mineral surfaces, and retention of pitch to the fibre material by cationic polymers. The aim of this study was to determine the influence of pH on some of the methods used for pitch control. Experiments were performed using laboratory-made wood pitch emulsions with varying pH, salt concentration, hemicellulose concentration and pitch composition. These emulsions were used to study the phase distribution of resin and fatty acids, the colloidal stability of pitch with and without steric stabilisation by galactoglucomannans, and the interactions between wood pitch and mineral particles. Purification of unbleached and peroxidebleached mill process water was performed by froth flotation in combination with a foaming agent. The distribution of resin and fatty acids (RFAs) between colloidal pitch droplets and the water phase was very dependent on pH. At pH 3, almost all of the RFAs were attached to the pitch droplets, while increasing the pH led to increasing concentration of dissolved RFAs in the water phase. The presence of salt shifted the release of RFAs towards higher pH, while lower ratio of neutral pitch in the emulsion resulted in release of RFAs at lower pH. It was also seen that the dissolution and adsorption of RFAs at sudden pHchanges takes place very quickly. Colloidal pitch was more stable against electrolyte-induced aggregation at higher pH, due to its higher anionic charge. The concentration of cationic polymers needed to aggregate colloidal pitch also increased with increasing pH. The surface characteristics of solid particles, such as amount of charged groups, were very important for understanding their interactions with colloidal wood pitch. Water-soluble galactoglucomannans stabilised the colloidal pitch sterically against aggregation, but could not completely prevent interactions between wood pitch and hydrophilic particles. Froth flotation of unbleached and peroxidebleached process water showed that the pitch could be removed more effectively and selectively at low pH, compared to at neutral pH. The pitch was removed more effectively, using lower concentrations of foaming agent, from peroxide-bleached water than from unbleached water. The results show that pH has a major impact on various pulping and papermaking processes. It determines the anionic charge of the colloidal pitch and the solubility of certain pitch components. Because of this, the pH influences the effectiveness of pitch retention and removal of pitch. The results indicate that pitch problems could be diminished by acknowledging the importance of pH in various papermaking processes.

Chromatoid body mediated RNA regulation in mouse male germline

Male germ cell differentiation, spermatogenesis is an exceptional developmental process that produces a massive amount of genetically unique spermatozoa. The complexity of this process along with the technical limitations in the germline research has left many aspects of spermatogenesis poorly understood. Post-meiotic haploid round spermatids possess the most complex transcriptomes of the whole body. Correspondingly, efficient and accurate control mechanisms are necessary to deal with the huge diversity of transcribed RNAs in these cells. The high transcriptional activity in round spermatids is accompanied by the presence of an uncommonly large cytoplasmic ribonucleoprotein granule, called the chromatoid body (CB) that is conjectured to participate in the RNA post-transcriptional regulation. However, very little is known about the possible mechanisms of the CB function. The development of a procedure to isolate CBs from mouse testes was this study’s objective. Anti-MVH immunoprecipitation of cross-linked CBs from a fractionated testicular cell lysate was optimized to yield considerable quantities of pure and intact CBs from mice testes. This protocol produced reliable and reproducible data from the subsequent analysis of CB’s protein and RNA components. We found that the majority of the CB’s proteome consists of RNA-binding proteins that associate functionally with different pathways. We also demonstrated notable localization patterns of one of the CB transient components, SAM68 and showed that its ablation does not change the general composition or structure of the CB. CB-associated RNA analysis revealed a strong accumulation of PIWI-interacting RNAs (piRNAs), mRNAs and long non-coding RNAs (lncRNAs) in the CB. When the CB transcriptome and proteome analysis results were combined, the most pronounced molecular functions in the CB were related to piRNA pathway, RNA post-transcriptional processing and CB structural scaffolding. In addition, we demonstrated that the CB is a target for the main RNA flux from the nucleus throughout all steps of round spermatid development. Moreover, we provided preliminary evidence that those isolated CBs slice target RNAs in vitro in an ATPdependent manner. Altogether, these results make a strong suggestion that the CB functions involve RNA-related and RNA-mediated mechanisms. All the existing data supports the hypothesis that the CB coordinates the highly complex haploid transcriptome during the preparation of the male gametes for fertilization. Thereby, this study provides a fundamental basis for the future functional analyses of ribonucleoprotein granules and offers also important insights into the mechanisms governing male fertility.

Chromatographic recovery of chemicals from acidic biomass hydrolysates

Lignocellulosic biomasses (e.g., wood and straws) are a potential renewable source for the production of a wide variety of chemicals that could be used to replace those currently produced by petrochemical industry. This would lead to lower greenhouse gas emissions and waste amounts, and to economical savings. There are many possible pathways available for the manufacturing of chemicals from lignocellulosic biomasses. One option is to hydrolyze the cellulose and hemicelluloses of these biomasses into monosaccharides using concentrated sulfuric acid as catalyst. This process is an efficient method for producing monosaccharides which are valuable platforn chemicals. Also other valuable products are formed in the hydrolysis. Unfortunately, the concentrated acid hydrolysis has been deemed unfeasible mainly due to high chemical consumption resulting from the need to remove sulfuric acid from the obtained hydrolysates prior to the downstream processing of the monosaccharides. Traditionally, this has been done by neutralization with lime. This, however, results in high chemical consumption. In addition, the by-products formed in the hydrolysis are not removed and may, thus, hinder the monosaccharide processing. In order to improve the feasibility of the concentrated acid hydrolysis, the chemical consumption should be decreased by recycling of sulfuric acid without neutralization. Furthermore, the monosaccharides and the other products formed in the hydrolysis should be recovered selectively for efficient downstream processing. The selective recovery of the hydrolysis by-products would have additional economical benefits on the process due to their high value. In this work, the use of chromatographic fractionation for the recycling of sulfuric acid and the selective recovery of the main components from the hydrolysates formed in the concentrated acid hydrolysis was investigated. Chromatographic fractionation based on the electrolyte exclusion with gel type strong acid cation exchange resins in acid (H+) form as a stationary phase was studied. A systematic experimental and model-based study regarding the separation task at hand was conducted. The phenomena affecting the separation were determined and their effects elucidated. Mathematical models that take accurately into account these phenomena were derived and used in the simulation of the fractionation process. The main components of the concentrated acid hydrolysates (sulfuric acid, monosaccharides, and acetic acid) were included into this model. Performance of the fractionation process was investigated experimentally and by simulations. Use of different process options was also studied. Sulfuric acid was found to have a significant co-operative effect on the sorption of the other components. This brings about interesting and beneficial effects in the column operations. It is especially beneficial for the separation of sulfuric acid and the monosaccharides. Two different approaches for the modelling of the sorption equilibria were investigated in this work: a simple empirical approach and a thermodynamically consistent approach (the Adsorbed Solution theory). Accurate modelling of the phenomena observed in this work was found to be possible using the simple empirical models. The use of the Adsorbed Solution theory is complicated by the nature of the theory and the complexity of the studied system. In addition to the sorption models, a dynamic column model that takes into account the volume changes of the gel type resins as changing resin bed porosity was also derived. Using the chromatography, all the main components of the hydrolysates can be recovered selectively, and the sulfuric acid consumption of the hydrolysis process can be lowered considerably. Investigation of the performance of the chromatographic fractionation showed that the highest separation efficiency in this separation task is obtained with a gel type resin with a high crosslinking degree (8 wt. %); especially when the hydrolysates contain high amounts of acetic acid. In addition, the concentrated acid hydrolysis should be done with as low sulfuric acid concentration as possible to obtain good separation performance. The column loading and flow rate also have large effects on the performance. In this work, it was demonstrated that when recycling of the fractions obtained in the chromatographic fractionation are recycled to preceding unit operations these unit operations should included in the performance evaluation of the fractionation. When this was done, the separation performance and the feasibility of the concentrated acid hydrolysis process were found to improve considerably. Use of multi-column chromatographic fractionation processes, the Japan Organo process and the Multi-Column Recycling Chromatography process, was also investigated. In the studied case, neither of these processes could compete with the single-column batch process in the productivity. However, due to internal recycling steps, the Multi-Column Recycling Chromatography was found to be superior to the batch process when the product yield and the eluent consumption were taken into account.

Weed control and green ear yield in maize

The objective of this work was to evaluate the influence of weeding frequency on cultivar Centralmex green corn yield. Two experiments were conducted in Mossoró-RN (Brazil), with the use of sprinkler irrigation. A random block design with four replicates was used. It was observed that the total number and weight (TW) of unhusked green ears, the number and weight of marketable unhusked ears and the number and weight of marketable husked ears were reduced under no weeding treatment. The number timing of weedings did not influence green corn yield, except for one weeding at 60 DAP, which was equivalent to the "no weeding" treatment, for TW. When maize is marketed considering the total number of green ears, higher net income is obtained when one weeding is carried out 45 days after planting.

Effect of plant row spacing and herbicide use on weed aboveground biomass and corn grain yield

The use of narrow plant spacing in corn (Zea mays) has been suggested as a technological alternative to obtain grain yield increases, due to a better use of resources. The regular pattern could diminish intraspecific competition while favoring interspecific competition with weeds. The objective of this study was to analyze the effect of corn row spacing on weed aboveground biomass and corn grain yield. Field experiments were conducted during 2002/2003 and 2003/2004 growing seasons. Three corn hybrids with two-row width (0.70 and 0.35 m) were tested. A greater photosynthetic photon flux density (PPFD) interception with a lower weed aboveground dry matter in narrow row arrangement was obtained. Corn grain yield was greater in the narrow row arrangement than in the wide row spacing. This increase in grain yield was related to a better resource use that allows for a reduced interspecific competition. The use of reduced spatial arrangement appeared to be an interesting alternative to increase both the grain yield potential and corn suppressive ability against weeds in corn dryland production systems.

Effects of weed control through cowpea intercropping on mayze morphology and yield

Intercropping combined with competitive maize cultivars can reduce the use of herbicides to control weeds. The objective of this work was to evaluate the effects of intercropping cowpea and maize, as well as hand-weeding on maize morphology and yield. The experimental design was in randomized complete blocks, with treatments arranged in split-plots and five replications. The plots consisted of four maize cultivars (BA 8512, BA 9012, EX 4001, EX 6004) and the split-plots consisted of the following treatments: no-weeding; twice hand-weeding (20 and 40 days after sowing); and intercropping with cowpea ('Sempre Verde' cultivar), both maize and cowpea sown at the same time. The variables evaluated were: maize fresh green ears and grain yield; characteristics of internodes, leaves, tassels, ears, grains; plant height and ear insertion height; number of weed plants and species; fresh and dry biomass of weed species and cowpea. Ten weed species were outstanding during the experiment, many of them from the Poaceae family. No interactions were found between weed control method and maize cultivars for most variables evaluated; and plants from hand-weeded split-plots showed superior mean values compared to plants from non-weeded and intercropped split-plots, both not differing from each other. The cowpea was inefficient in controlling weed, reducing the maize yields and not producing any grain. The maize cultivars 'BA 8512' and 'BA 9012 showed the highest mean green ear yield, and the highest grain yield in hand-weeded, no-weeded and intercropped split-plots. On the other hand, the maize cultivar 'EX 6004' showed such high means only in no-weeded and intercropped split-plots. 'EX 4001 presented the worst means in these variables for hand-weeded, no-weeded ant intercropped split-plots.

Growth, nodulation, and yield of soybean and associated weeds as affected by weed management

Two field experiments were conducted at the experimental farm of the National Research Centre at Shalakan, Kalubia Governorate, Egypt, during 2006 and 2007 seasons, to study the effect of three pre-emergence herbicides, prometryn [at the rate of 0.75, 1.5 and 2.25 kg ha-1], oxadiargyl [at the rate of 240, 480 and 720 g ha-1] and butralin [at the rate of 1.20, 2.40 and 3.36 kg ha-1], two hand hoeing treatments and a nonweeded check, on weed infestation, nodulation, growth, yield and yield attributes of soybean plants. Two hand hoeing treatments resulted in the highest weed depression expressed as the lowest fresh and dry weights of broadleaved, grassy and total weeds. The reduction percentage in weed dry matter compared to the nonweeded treatment was 98.3, 92.64 and 96.9% in broadleaved, grassy and total weeds, respectively. Application of the three herbicides at higher or recommended doses significantly reduced fresh and dry weight of the weeds compared to the nonweeded treatment. The results indicated that all the three herbicides at rates higher than the recommended markedly decreased the number, fresh and dry weight of nodules as well as root, shoot and total dry weight plant-1, while application of two hand hoeing treatments significantly increased these traits. Two hand hoeing treatments and pre-emergence herbicides at the recommended rates markedly increased soybean yield and its attributes. Two hand hoeing treatments gave the highest values of number of pods per plant-1, weight of pods per plant-1 and number of seeds per plant-1 by 140.7, 150.0 and 59.8%, respectively, compared to the nonweeded treatment. On the other hand, oxadiargyl at the recommended rate (480 g ha-1) was the best treatment for promoting seed yield (g plant-1), seed yield (kg ha-1) and biological yield (g plant-1) compared to the nonweeded treatment by 87.3, 85.0 and 88.2%, respectively. Prometryn at the rate of 1.50 kg ha-1, followed by two hand hoeing treatments, produced the highest shoot and seed protein percentage as well as seed oil percentage, compared to the other weed control treatments.

Growth and yield of corn grain and green ear in competition with weeds

Studies on plant growth are interesting because they provide explanations for the factors that influence yield in various crops. The objective of this work was to evaluate growth and yield in corn cultivar AG1051, when in competition with weeds. Cultivar AG 1051 was submitted to two groups of treatments: weed control, and sampling periods for dry biomass evaluation. The weed control treatments consisted of hoeing (two hoeings performed at 20 and 40 days after sowing) and no hoeing. Sampling periods consisted of collecting the above-ground part and roots of corn every fifteen days, until 105 days after sowing (DAS); the first sampling was performed 30 DAS. A completely randomized block design with ten replicates was used. For the characteristics evaluated in a single season, statistical analyses were carried out as a random block experiment. For the characteristics evaluated in several periods, statistical analyses were carried out as random blocks with split-plots (weed control assigned to plots). Fourteen weed species, unevenly distributed throughout the experimental area, were the most important. The growth observed for the above-ground part and root system of corn was 30% smaller in the non-hoed plots, compared to the hoed plots. Lack of weed control increased dry matter of the above-ground part of the weeds and reduced the number of unhusked and husked marketable green ears by 23% and 49%, respectively. Grain yield reduction caused by lack of weed control reached 38%.

Green ear yield and grain yield of maize cultivars in competition with weeds

The reduction in herbicide use is one of the greatest interests for modern agriculture and several alternatives are being investigated with this objective, including the adoption of cultivars that suppress weeds. The objective of this study was to verify if maize cultivars develop differently, in competition with weeds, to produce green ears and grain. Randomized complete block design was used, with split-plots and five replications. Cultivars DKB 390, DKB 466, DKB 350, AG 7000, AG 7575 and Master, were evaluated in the plots, without weeding and two weedings (at 22 and 41 days after sowing) in sub plots. Twenty-one species were identified in the experimental area, the most frequent being Gramineae (Poaceae), Euphorbiaceae, Leguminosae (Fabaceae) and Convolvulaceae species. There was no difference in the dry biomass above-ground part of the weeds in the plots of the evaluated cultivars. The cultivars behaved similarly in treatments with or without hoeing, except for plant height and ear height evaluations. Without hoeing, plant height increased in cultivar DKB 390, while plant height and ear height decreased in cultivar AG 7575. In the other cultivars, these traits did not change under weed control. The presence of weeds decreased the values of all traits employed to assess green corn yield, with the exception of the total number of green ears and grain yield.

Corn yield response to weed and fall armyworm controls

The interference imposed the by weeds on corn decreases practically all vegetative characteristics. As consequence, the green ear and grain yield are also reduced. Losses due to the fall armyworm (Spodoptera frugiperda) attack can reduce corn grain yield up to 34%. In general, weed and insect control issues are addressed separately in research papers. Nevertheless, interaction between weeds and insects may exist. This study aimed to evaluate green ear and corn grain yield response to weed and fall armyworm control. A completely randomized block design with split-plots and five replicates was adopted. Corn cultivar AG 1051 was grown under weedy conditions or with control by hand hoeings performed at 20 and 40 days after planting. Fall armyworm control (applied to subplots) was performed with sprays of water (control), deltamethrin (5g active ingredient ha-1); neem oil, at 0.5% (diluted in water), and neem leaf extract at 5%. Each product was sprayed three times, at seven-day intervals, starting at the 7th day after planting, using 150 L ha-1 of the tank solution. Dry mass of the above-ground part, internode diameter, leaf length, leaf width, leaf area, green ear yield and grain yield of corn were reduced due to the lack of weed control. Fall armyworm control in the weeded plots did not influence green ear yield and grain yield, except green mass of marketable, husked ears, which was reduced when the caterpillar was not controlled. Without weed control, neem extracts and deltamethrin sprays provided highest yields of number and total weight of green ears with husks, number and weight of marketable ears with husks and number of marketable ears without husks. The best results for husked ear mass and for grain yield were obtained with neem extract and deltamethrin, respectively.

Nitrogen doses and weed control via intercropping with gliricidia for corn production

Many studies have demonstrated the beneficial influence of nitrogen doses on corn dry grain yield and green ear yield. Due to a growing concern with environmental degradation, many agricultural practices, adopted in the past, are being reexamined. With regard to weed control, strategies that employ mechanical control, including intercrops, are being the object of renewed interest. The purpose of this study was to evaluate the effects of the application of nitrogen doses (0, 40, 80, and 120 kg N ha-1; as ammonium sulfate) and weed control on the growth, green ear yield, and grain yield of the AG 1051 corn cultivar. A randomized block experimental design with split-plots and nine replications was adopted. In addition to nitrogen rates, the AG 1051 cultivar was submitted to the following treatments, applied to subplots: no weeding, two hoeings (at 20 and 40 days after sowing), and intercropping with gliricídia (Gliricidia sepium). Gliricidia was sowed at corn planting, between the corn rows, using two seedlings per pit, in pits spaced 0.30 m apart. Gliricidia did not provide weed control, and gave plant growth, green ear yield and grain yield values similar to the no weeding treatment. However, regarding the number of mature ears got, intercropping with gliricidia did not differ from the two-hoeing treatment. Weed control did not have an effect on plant height and number of marketable, husked green ears, with the application of 120 kg N ha-1; indicating that nitrogen improved the corn's competitive ability. The two-hoeing treatment provided the best means for total green ears weight, number of marketable husked ears, both unhusked and husked marketable ear weight, grain yield and its components than the other treatments. Nitrogen application increased corn growth, green ear yield, and grain yield, as well as weed green biomass, but reduced the stand and growth of gliricidia.

Corn growth and yield in competition with weeds

Although labor is intensive, evaluating the growth of crops may allow a better understanding of crop performance, including the reasons why certain cultivars can compete better with weeds. This study aims at evaluating growth, green ear yield, and grain yield in corn when in competition with weeds. Cultivars AG 1051 and BRS 106 were grown with (two hoeings, at 20 and 40 days after sowing) or without weed control. In order to evaluate crop growth, six collections of the above-ground part and the root system of corn were performed, every 15 days, with the first collection made 30 days after sowing. A randomized complete block design was adopted, with split-split plots (weed control in plots, cultivars in subplots, and collections in sub-subplots) and ten replicates. Eighteen weed species were found in the experiment area. Increased values of corn leaf area, above-ground part and root system, due to plant age function, were smaller in non-hoed plots than in hoed plots and were dependent upon cultivar. The lack of weed control increased dry matter of weeds aboveground part and decreased green ear yield and grain yield. Cultivar AG 1051 had higher increases in leaf area, above-ground part of the plant and root system, due to plant age function, and controlled weeds better than cultivar BRS 106. In addition, cultivar AG 1051 was superior to other cultivars with respect to most traits used for green corn yield and grain yield assessment.

Effects of irrigated rice sowing season and imazapyr + imazapic time of application on rice grain yield and red rice management

Irrigated rice sowing season and red rice competition are among the main factors affecting grain yield. The objective of this work was to evaluate the sowing date of irrigated rice and moments of application of the herbicide imazapyr + imazapic to control red rice management and irrigated rice grain yield. Eight experiments were performed at the following dates (09/30, 10/19, 11/08 and 12/01) for the 2010/2011 harvest season and (09/27, 10/17, 11/08 and 12/05) for the 2011/2012 harvest season. The treatments were: application of the herbicide imazapyr + imazapic at doses of 105+35 g ha-1 in pre-emergence (PRE); 52.5+17.5 g ha‑1 in pre-emergence and 52.5+17.5 g ha-1 in post-emergence (PRE + POST); and 105+35 g ha-1 in post- emergence (POST), and a control without application and no weeding. The cultivar Puitá Inta CL was used and a randomized block design with four replicates. A joint analysis of the experiments was carried out. There was less emergence of red rice and higher grain yield of the irrigated rice at the early periods (09/30/10 and 09/27/11), with 10,578 and 8,653 kg ha-1, respectively. At the end of the season (12/01/10 and 12/05/11), there was greater reduction of the red rice seed bank. Sowing at the beginning of the recommended period provided more irrigated rice grain yield. The application of imazapyr + imazapic at a dose of 52.5+17.5 g ha-1 in PRE + 52.5+17.5 g ha-1 POST, and 105+35 g ha-1 only in PRE and POST was effective in the control of red rice.