Enhanced multi-wavelength holographic profilometry by laser mode selection

The application of multi-wavelength holography for surface shape measurement is presented. In our holographic setup a Bi12TiO 20 (BTO) photorefractive crystal was the holographic recording medium and a multimode diode laser emitting in the red region was the light source in a two-wave mixing scheme. The holographic imaging with multimode lasers results in multiple holograms in the BTO. By employing such lasers the resulting holographic image appears covered of interference fringes corresponding to the object relief and the interferogram spatial frequency is proportional to the diode laser free spectral range (FSR). We used a Fabry-Perot étalon at the laser output for laser mode selection. Thus, larger effective values of the laser FSR were achieved, leading to higher-spatial frequency interferograms and therefore to more sensitive and accurate measurements. The quantitative evaluation of the interferograms was performed through the phase stepping technique (PST) and the phase map unwrapping was carried out through the Cellular-Automata method. For a given surface, shape measurements with different interferogram spatial frequencies were performed and compared, concerning measurement noise and visual inspection.

Preliminary selection of acerola genotypes in Brazil

Introduction. Breeding studies for acerola (Malpighia glabra) improvement aim at obtaining plants that produce fruits with uniform chemical and physical attributes, including high levels of vitamin C, which can provision the market with fresh fruit and frozen pulp. High variability in fruit quality is observed in Brazilian acerola crops, especially those propagated by seeds. In this context, the objective of our research was to evaluate the physical and chemical characteristics of Brazilian acerola genotype fruits. Materials and methods. Sixteen acerola genotypes were studied in Jaboticabal, São Paulo State, Brazil. A completely randomized design with sixteen treatments and six replications was adopted. Each treatment was represented by one genotype. Several parameters related to fruit quality, such as width, length, weight, pulp percentage, soluble solids (SS), titratable acidity (TA), [SS / TA] ratio and vitamin C content, were evaluated in fruits of the acerola genotypes. The results were submitted to variance analyses, the Tukey test and cluster analysis. Results and discussion. There was a statistical difference between the acerola genotypes studied. Three of them stood out as natural sources of vitamin C. In spite of fruit size, two acerola genotypes were found to have potential for fresh fruit production. In a general form, genotypes that presented a high [SS / TA] ratio had low vitamin C content. Conclusion. The acerola genotypes studied in Jaboticabal presented high variability, forming eleven groups in relation to fruit quality parameters. © 2007 Cirad/EDP Sciences All rights reserved.

Freezing point and thermal conductivity of tropical fruit pulps: Mango and papaya

The freezing point depression of mango and papaya pulps was measured by using a simple apparatus, consisting of two major sections: a freezing vessel and a data acquisition system. The thermal conductivity of both pulps as a function of frozen water fraction and temperature was also investigated by using a coaxial dual-cylinder apparatus. Thermal conductivity above the initial freezing point was well fitted by polynomial equations. Below the freezing point, the thermal conductivity was strongly affected by both the frozen water fraction and temperature. Simple equations in terms of frozen water fraction and temperature could be fitted to the experimental data of freezing point depression and thermal conductivity.

Comparison of environmental indicators of two aviaries for laying Hens

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Assessment of the flexural strength of two heat-curing acrylic resins for artificial eyes

Prosthetic eyes are artificial substitutes for the eyeball, made of heat-curing acrylic resin, serving to improve the esthetic appearance of the mutilated patient and his/her inclusion in society. The aim of this study was to assess the flexural strength of two heat-curing acrylic resins used for manufacturing prosthetic eyes. Thirty-six specimens measuring 64 x 10 x 3.3 mm were obtained and divided into four groups: acrylic resin for artificial sclera N1 (Artigos Odontológicos Clássico, São Paulo, SP, Brazil), heat-cure water technique (GI) and microwave-cured (GII); colorless acrylic resin for prosthetic eyes (Artigos Odontológicos Clássico, São Paulo, SP, Brazil), heat-cure water technique (GIII) and microwave-cured (GIV). Mechanical tests using three point loads were performed in a test machine (EMIC, São José dos Pinhais, PR, Brazil). The analysis of variance and the Tukey test were used to identify significant differences (p < 0.01). Groups GII and GIV presented, respectively, the highest (98.70 ± 11.90 MPa) and lowest means (71.07 ± 8.93 MPa), with a statistically significant difference. The cure method used for the prosthetic eye resins did not interfere in their flexural strength. It was concluded that all the resins assessed presented sufficient flexural strength values to be recommended for the manufacture of prosthetic eyes.

Laboratory assessment of two active ingredients for control of coptotemes gestroi (Isoptera: Rhinotermitidae)

The subterranean termite Coptotermes gestroi Wasmann (Isoptera: Rhinotermitidae) is a pest of major economic importance in urban environments of southeastern Brazil. Compared to using pesticides for termite control, termite bait products target termites more specifically and also address environmental contamination issues. In this point of view, we performed two different bioassays in order to evaluate the efficacy of boric acid and fipronil against different populations of C. gestroi. The results showed that concentrations between 2000 and 3000 ppm of boric acid caused approximately 100 percent mortality in termites. Concentrations between 0.01 and 0.0001 ppm of fipronil resulted in 100% termite mortality after 2 wk exposure. The data displayed a fast mortality of termites contaminated with fipronil, even with small concentrations, and therefore it is not a suitable product to be used in baits against C. gestroi. The present study showed a delayed toxicity of boric acid against the subterranean termite C. gestroi which suggests a need for further field tests.

Selection of endogenous genes for gene expression studies in Eucalyptus under biotic (Puccinia psidii) and abiotic (acibenzolar-S-methyl) stresses using RT-qPCR

Background: Rust caused by Puccinia psidii Winter has been limiting for the establishment of new Eucalyptus plantations, as well as for resprouting of susceptible genetic materials. Identifying host genes involved in defense responses is important to elucidate resistance mechanisms. Reverse transcription-quantitative PCR is the most common method of mRNA quantitation for gene expression analysis. This method generally employs a reference gene as an internal control to normalize results. A good endogenous control transcript shows minimal variation due to experimental conditions. Findings. We analyzed the expression of 13 genes to identify transcripts with minimal variation in leaves of 60-day-old clonal seedlings of two Eucalyptus clones (rust-resistant and susceptible) subjected to biotic (P. psidii) and abiotic (acibenzolar-S-methyl, ASM) stresses. Conclusions. For tissue samples of clones that did not receive any stimulus, a combination of the eEF2 and EglDH genes was the best control for normalization. When pathogen-inoculated and uninoculated plant samples were compared, eEF2 and UBQ together were more appropriate as normalizers. In ASM-treated and untreated leaves of both clones, transcripts of the CYP and elF4B genes combined were the ones with minimal variation. Finally, when comparing expression in both clones for ASM-treated leaves, P. psidii-inoculated leaves, ASM-treated plus P. psidii-inoculated leaves, and their respective controls, the genes with the most stable expression were EgIDH and UBQ. The chitinase gene, which is highly expressed in studies on plant resistance to phytopathogens, was used to confirm variation in gene expression due to the treatments. © 2010 Laia et al; licensee BioMed Central Ltd.

The overall coefficient of the two-loop superstring amplitude using pure spinors

Using the results recently obtained for computing integrals over (non-minimal) pure spinor superspace, we compute the coefficient of the massless two-loop four-point amplitude from first principles. Contrasting with the mathematical difficulties in the RNS formalism where unknown normalizations of chiral determinant formulæ force the two-loop coefficient to be determined only indirectly through factorization, the computation in the pure spinor formalism can be smoothly carried out. © SISSA 2010.

Network node with wireless and wired interfaces: Nios II processor and uClinux to development of a NCAP embedded (IEEE 1451.1) with two interfaces, wireless (IEEE 1451.5) and wired (IEEE p1451.2)

This paper presents a NCAP embedded on DE2 kit with Nios II processor and uClinux to development of a network gateway with two interfaces, wireless (ZigBee) and wired (RS232) based on IEEE 1451. Both the communications, wireless and wired, were developed to be point-to-point and working with the same protocols, based on IEEE 1451.0-2007. The tests were made using a microcomputer, which through of browser was possible access the web page stored in the DE2 kit and send commands of control and monitoring to both TIMs (WTIM and STIM). The system describes a different form of development of the NCAP node to be applied in different environments with wired or wireless in the same node. © 2011 IEEE.

Comparative analysis of current and voltage-controlled photovoltaic Maximum Power Point tracking

Maximum Power Point tracking (MPPT) in photovoltaic (PV) systems may be achieved by controlling either the voltage or current of the PV device. There is no consensus in the technical literature about how is the best choice. This paper provides a comparative analysis performance among current and voltage control using two different MPPT strategies: the perturb and observe (P&O) and the incremental conductance techniques. © 2011 IEEE.

First telemetry study of bush dogs: Home range, activity and habitat selection

Context The bush dog (Speothos venaticus) is difficult to observe, capture, and study. To date, indirect evidence and opportunistic field observations have been the primary sources of information about the species' ecology. Field data are urgently needed to clarify the species' ecological requirements, behaviour and movement patterns. Aims The present study uses 13 months of telemetry data from a group of bush dogs to begin to address questions about area requirements, habitat preferences and movement patterns of this difficult-to-study species. Methods We tracked a group of bush dogs (two adults, one juvenile, four young) in an area of intact and altered Cerrado (woodlandsavanna biome) in eastern Mato Grosso, Brazil (Nova Xavantina District). Key results The group had a total home range of 140km2 (fixed kernel 95%), with smaller seasonal 'subareas' (areas used for 12 months before moving to another area, with repetition of some areas over time) and demonstrated a preference for native habitats. Conclusions The bush dog's home range is greater than that of other canids of the same size, even correcting for group size. Patterns of seasonal movement are also different from what has been observed in other South American canids. Implications From our observations in the Brazilian savanna, bush dogs need large tracks of native habitat for their long-term persistence. Although the present study is based on a single pack, it is highly relevant for bush dog conservation because it provides novel information on the species' spatial requirements and habitat preferences. © 2012 CSIRO.

Model to design drip hose lateral line using two spacing between emitters

The use of non-pressure compensating drip hose in horticultural and annual cycle fruits is growing in Brazil. In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. A computer program was developed in Delphi based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose.

Optimal conductor size selection and reconductoring in radial distribution systems using a mixed-integer LP approach

This paper presents a mixed-integer linear programming model to solve the conductor size selection and reconductoring problem in radial distribution systems. In the proposed model, the steady-state operation of the radial distribution system is modeled through linear expressions. The use of a mixed-integer linear model guarantees convergence to optimality using existing optimization software. The proposed model and a heuristic are used to obtain the Pareto front of the conductor size selection and reconductoring problem considering two different objective functions. The results of one test system and two real distribution systems are presented in order to show the accuracy as well as the efficiency of the proposed solution technique. © 1969-2012 IEEE.

Genome-Wide Analysis Reveals Selection for Important Traits in Domestic Horse Breeds

Intense selective pressures applied over short evolutionary time have resulted in homogeneity within, but substantial variation among, horse breeds. Utilizing this population structure, 744 individuals from 33 breeds, and a 54,000 SNP genotyping array, breed-specific targets of selection were identified using an FST-based statistic calculated in 500-kb windows across the genome. A 5.5-Mb region of ECA18, in which the myostatin (MSTN) gene was centered, contained the highest signature of selection in both the Paint and Quarter Horse. Gene sequencing and histological analysis of gluteal muscle biopsies showed a promoter variant and intronic SNP of MSTN were each significantly associated with higher Type 2B and lower Type 1 muscle fiber proportions in the Quarter Horse, demonstrating a functional consequence of selection at this locus. Signatures of selection on ECA23 in all gaited breeds in the sample led to the identification of a shared, 186-kb haplotype including two doublesex related mab transcription factor genes (DMRT2 and 3). The recent identification of a DMRT3 mutation within this haplotype, which appears necessary for the ability to perform alternative gaits, provides further evidence for selection at this locus. Finally, putative loci for the determination of size were identified in the draft breeds and the Miniature horse on ECA11, as well as when signatures of selection surrounding candidate genes at other loci were examined. This work provides further evidence of the importance of MSTN in racing breeds, provides strong evidence for selection upon gait and size, and illustrates the potential for population-based techniques to find genomic regions driving important phenotypes in the modern horse. © 2013 Petersen et al.

Saddle points and rare collisions under scaling approach in a Fermi accelerator with two nonlinear terms

Rare collisions of a classical particle bouncing between two walls are studied. The dynamics is described by a two-dimensional, nonlinear and area-preserving mapping in the variables velocity and time at the instant that the particle collides with the moving wall. The phase space is of mixed type preventing diffusion of the particle to high energy. Successive and therefore rare collisions are shown to have a histogram of frequency which is scaling invariant with respect to the control parameters. The saddle fixed points are studied and shown to be scaling invariant with respect to the control parameters too. © 2012 Elsevier B.V. All rights reserved.