[Future cardiac pacemakers – technical visions].

Cardiac pacemakers are routinely used for the treatment of bradyarrhythmias. Contemporary pacemakers are reliable and allow for a patient specific programming. However, pacemaker replacements due to battery depletion are common (~25 % of all implantation procedures) and bear the risk of complications. Batteryless pacemakers may allow overcoming this limitation. To power a batteryless pacemaker, a mechanism for intracorporeal energy harvesting is required. Such a generator may consist out of subcutaneously implanted solar cells, transforming the small amount of transcutaneously available light into electrical energy. Alternatively, intravascular turbines may harvest energy from the blood flow. Energy may also be harvested from the ventricular wall motion by a dedicated mechanical clockwork converting motion into electrical energy. All these approaches have successfully been tested in vivo. Pacemaker leads constitute another Achilles heel of contemporary pacemakers. Thus, leadless devices are desired. Miniaturized pacemaker circuits and suitable energy harvesting mechanisms (incorporated in a single device) may allow catheter-based implantation of the pacemaker in the heart. Such miniaturized battery- and leadless pacemakers would combine the advantages of both approaches and overcome major limitations of today’s systems.

Experimental Model to estimate shading losses on PV arrays

This paper presents a simple mathematical model to estimateshadinglosses on PVarrays. The model is applied directly to power calculations, without the need to consider the whole current–voltage curve. This allows the model to be used with common yield estimation software. The model takes into account both the shaded fraction of the array area and the number of blocks (a group of solar cells protected by a bypass diode) affected by shade. The results of an experimental testing campaign on several shaded PVarrays to check the validity of model are also reported.

Roadmap towards efficiencies over 40% at ultra-high concentrations (> 1000 suns)

High efficiency solar cells working under ultra-high concentrations (>;1000X) have been shown to be a promising solution to decrease the cost of PV electricity, increase the efficiency and circumvent the material availability restrictions for massive PV penetration. A detailed analysis of the limitations of our current triple junction solar cell (36.2% at 700X), in the quest to maximize efficiency at 1000X, shows that the main improvements to tackle are: a) implementation of a high band gap tunnel junction; b) increase the band gap of the top cell; c) fine current matching tune; d) enhancement of the front contact process. This constitutes our roadmap to reach an efficiency over 41%

Real-time reliability test for a CPV module based on a power degradation model

Models based on degradation are powerful and useful tools to evaluate the reliability of those devices in which failure happens because of degradation in the performance parameters. This paper presents a procedure for assessing the reliability of concentrator photovoltaic (CPV) modules operating outdoors in real-time conditions. With this model, the main reliability functions are predicted. This model has been applied to a real case with a module composed of GaAs single-junction solar cells and total internal reflection (TIR) optics

High-efficiency Köhler photovoltaic concentrators with external light confinement

Metal grid lines are a vital element in multijunction solar cells in order to take out from the cell the generated photocurrent. Nevertheless all this implies certain shadowing factor and thus certain reflectivity on cells surface that lowers its light absorption. This reflectivity produces a loss in electrical efficiency and thus a loss in global energy production for CPV systems. We present here an optical design for recovering this portion of reflected light, and thus leading to a system efficiency increase. This new design is based on an external confinement cavity, an optical element able to redirect the light reflected by the cell towards its surface again. It has been possible thanks to the recent invention of the advanced Köhler concentrators by LPI, likely to integrate one of these cavities easily. We have proven the excellent performance of these cavities integrated in this kind of CPV modules offering outstanding results: 33.2% module electrical efficiency @Tcell=25ºC and relative efficiency and Isc gains of over 6%.

Evidence of charge carrier number fluctuations in InN thin films?

Due to its small band-gap and its high mobility, InN is a promising material for a large number of key applications like band-gap engineering for high efficiency solar cells, light emitting diodes, and high speed devices. Unfortunately, it has been reported that this material exhibits strong surface charge accumulation which may depend on the type of surface. Current investigations are conducted in order to explain the mechanisms which govern such a behavior and to look for ways of avoiding it and/or finding applications that may use such an effect. In this framework, low frequency noise measurements have been performed at different temperatures on patterned MBE grown InN layers. The evolution of the 1/f noise level with temperature in the 77 K-300 K range is consistent with carrier number fluctuations thus indicating surface mechanisms: the surface charge accumulation is confirmed by the noise measurements.

Dissolution and gettering of iron during contact co-firing

The dissolution and gettering of iron is studied during the final fabrication step of multicrystalline silicon solar cells, the co-firing step, through simulations and experiments. The post-processed interstitial iron concentration is simulated according to the as-grown concentration and distribution of iron within a silicon wafer, both in the presence and absence of the phosphorus emitter, and applying different time-temperature profiles for the firing step. The competing effects of dissolution and gettering during the short annealing process are found to be strongly dependant on the as-grown material quality. Furthermore, increasing the temperature of the firing process leads to a higher dissolution of iron, hardly compensated by the higher diffusivity of impurities. A new defect engineering tool is introduced, the extended co-firing, which could allow an enhanced gettering effect within a small additional time

E-beam nanopatterning for the selective area growth of III-V nitride nanorods

GaN/InGaN nanorods have attracted much scientific interest during the last decade because of their unique optical and electrical properties [1,2]. The high crystal quality and the absence of extended defects make them ideal candidates for the fabrication of high efficiency opto-electronic devices such as nano-photodetectors, light-emitting diodes, and solar cells [1-3]. Nitrides nanorods are commonly grown in the self-assembled mode by plasma-assisted molecular beam epitaxy (MBE) [4]. However, self-assembled nanorods are characterized by inhomogeneous heights and diameters, which render the device processing very difficult and negatively affect the electronic transport properties of the final device. For this reason, the selective area growth (SAG) mode has been proposed, where the nanorods preferentially grow on pre-defined sites on a pre-patterned substrate [5].

Towards 35% Efficient Concentrator Modules Based On LPI Köhler Concentrators With External Confinement Cavities

Multijunction solar cells present a certain reflectivity on its surface that lowers its light absorption. This reflectivity produces a loss in electrical efficiency and thus a loss in global energy production for CPV systems. We present here an optical design for recovering this portion of reflected light, and thus leading to a system efficiency increase. This new design is based on an external confinement cavity, an optical element able to redirect the light reflected by the cell towards its surface again. We have proven the excellent performance of these cavities integrated in CPV modules offering outstanding results: 33.2% module electrical efficiency @Tcell  =  25 °C and relative efficiency and Isc gains of over 6%

Analysis of the Mechanical Properties of Multicrystalline and Monocrystalline Silicon Wafers Manufactured by Casting Methods

Quasi-monocrystalline silicon wafers have appeared as a critical innovation in the PV industry, joining the most favourable characteristics of the conventional substrates: the higher solar cell efficiencies of monocrystalline Czochralski-Si (Cz-Si) wafers and the lower cost and the full square-shape of the multicrystalline ones. However, the quasi-mono ingot growth can lead to a different defect structure than the typical Cz-Si process. Thus, the properties of the brand-new quasi-mono wafers, from a mechanical point of view, have been for the first time studied, comparing their strength with that of both Cz-Si mono and typical multicrystalline materials. The study has been carried out employing the four line bending test and simulating them by means of FE models. For the analysis, failure stresses were fitted to a three-parameter Weibull distribution. High mechanical strength was found in all the cases. The low quality quasi-mono wafers, interestingly, did not exhibit critical strength values for the PV industry, despite their noticeable density of extended defects.

Development of low cost photovoltaic sensor for over-tree radiation assessment

The crop diseases sometimes are related to the irradiance that the crop receives. When an experiment requires the measurement of the irradiance, usually it results in an expensive data acquisition system. If it is necessary to check many test points, the use of traditional sensors will increase the cost of the experiment. By using low cost sensors based in the photovoltaic effect, it is possible to perform a precise test of irradiance with a reduced price. This work presents an experiment performed in Ademuz (Valencia, Spain) during September of 2011 to check the validity of low cost sensors based on solar cells.

An investigation into hot-spots in two large grid-connected PV plants

This paper details an investigation into the appearance of hot-spots in two large grid-connected photovoltaics (PV) plants, which were detected after the visual inspection of trackers whose energy output was decreasing at anomalous rate. Detected hot-spots appeared not only in the solar cells but also in resistive solder bonds (RSB) between cells and contact ribbons. Both types cause similar irreversible damage to the PV modules, but the latter are the main responsible for the detected decrease in energy output, which was confirmed in an experimental testing campaign. The results of this investigation, for example, how hot-spots were detected or their impact on the output power of PV modules, may be of interest for the routine maintenance of large grid-connected PV plants.

Experimental model to estimate shading losses on PV arrays

This paper presents a simple mathematical model to estimate shading losses on PV arrays. The model is applied directly to power calculations, without the need to consider the whole current–voltage curve. This allows the model to be used with common yield estimation software. The model takes into account both the shaded fraction of the array area and the number of blocks (a group of solar cells protected by a bypass diode) affected by shade. The results of an experimental testing campaign on several shaded PV arrays to check the validity of model are also reported.

Ensayos acelerados de fiabilidad de células solares de concentración

SUMMARY Concentration Photovoltaic Systems (CPV) have been proposed as an alternative to conventional systems. During the last years, there has been a boom of the CPV industry caused by the technological progress in all the elements of the system. and mainly caused by the use of multijunction solar cells based on III-V semiconductors, with efficiencies exceeding to 43%. III-V solar cells have been used with high reliability results in a great number of space missions without concentration. However, there are no previous results regarding their reliability in concentration terrestrial applications, where the working conditions are completely different. This lack of experience, together with the important industrial interest, has generated the need to evaluate the reliability of the cells. For this reason, nowadays there are several research centers around the undertaking this task. The evaluation of the reliability of this type of devices by means of accelerated tests is especially problematic when they work at medium or high concentration, because it is practically impossible to emulate real working conditions of the cell inside climatic chambers. In fact, as far as we know, the results that appear in this Thesis are the first estimating the Activation Energy of the failure mechanism involved, as well as the warranty of the III-V concentrator solar cells tested here. To evaluate the reliability of III-V very high concentrator solar cells by means of accelerated tests, a variety of activities, described in this Thesis have been carried out. The First Part of the memory presents the theoretical part of the Doctoral Thesis. After the Introduction, chapter 2 presents the state of the art in degradation and reliability of CPV systems and solar cells. Chapter 3 introduces some reliability definitions and the application of specific statistical functions to the evaluation of the reliability and parameters. From these functions, important parameters will be calculated to be used later in the experimental results of Thesis. The Second Part of the memory contains the experimental. Chapter 4 shows the types of accelerated tests and the main goals pursuit with them when carried out over CPV systems and solar cells. In order to evaluate quantitatively the reliability of the III-V concentrator solar cells used in these tests, some modifications have been introduced which discussion will be tackled here. Based on this analysis the working plan of the tests carried out in this Doctoral Thesis is presented. Chapter 5 presents a new methodology as well as the necessary instrumentation to carry out the tests described here. This new methodology takes into account the adaptation, improvement and novel techniques needed to test concentrator solar cells. The core of this memory is chapter 6, which presents the results of the characterization of the cells during the accelerated life tests and the analysis of the aforementioned results with the purpose of getting quantitative values of reliability in real working conditions. The acceleration factor of the accelerated life tests, under nominal working conditions has been calculated. Accordingly, the validity of the methodology as well as the calculations based on the reliability assessment, have also been demonstrated. Finally, quantitative values of degradation, reliability and warranty of the solar cells under field nominal working conditions have been calculated. With the development of this Doctoral Thesis the reliability of very high concentrator GaAs solar cells of small area has been evaluated. It is very interesting to generalize the procedures described up to this point to III-V multijunction solar cells of greater area. Therefore, chapter 7 develops this generalization and introduces also a useful thermal modeling by means of finite elements of the test cells’ circuits. In the last chapter, the summary of the results and the main contributions of this Thesis are outlined and future research activities are identified. RESUMEN Los Sistemas Fotovoltaicos de Concentración (SFC) han sido propuestos como una alternativa a los sistemas convencionales de generación de energía. Durante los últimos años ha habido un auge de los SFC debido a las mejoras tecnológicas en todos los elementos del sistema, y principalmente por el uso de células multiunión III-V que superan el 43% de rendimiento. Las células solares III-V han sido utilizadas con elevada fiabilidad en aplicaciones espaciales sin concentración, pero no existe experiencia de su fiabilidad en ambiente terrestre a altos niveles de concentración solar. Esta falta de experiencia junto al gran interés industrial ha generado la necesidad de evaluar la fiabilidad de las células, y actualmente hay un significativo número de centros de investigación trabajando en esta área. La evaluación de la fiabilidad de este tipo de dispositivos mediante ensayos acelerados es especialmente problemática cuando trabajan a media o alta concentración por la casi imposibilidad de emular las condiciones de trabajo reales de la célula dentro de cámaras climáticas. De hecho, que sepamos, en los resultados de esta Tesis se evalúa por primera vez la Energía de Activación del mecanismo de fallo de las células, así como la garantía en campo de las células de concentración III-V analizadas. Para evaluar la fiabilidad de células solares III-V de muy alta concentración mediante ensayos de vida acelerada se han realizado diversas actividades que han sido descritas en la memoria de la Tesis. En la Primera Parte de la memoria se presenta la parte teórica de la Tesis Doctoral. Tras la Introducción, en el capítulo 2 se muestra el estado del arte en degradación y fiabilidad de células y Sistemas Fotovoltaicos de Concentración. En el capítulo 3 se exponen de forma resumida las definiciones de fiabilidad y funciones estadísticas que se utilizan para la evaluación de la fiabilidad y sus parámetros, las cuales se emplearán posteriormente en los ensayos descritos en este Tesis. La Segunda Parte de la memoria es experimental. En el capítulo 4 se describen los tipos y objetivos de los ensayos acelerados actualmente aplicados a SFC y a las células, así como las modificaciones necesarias que permitan evaluar cuantitativamente la fiabilidad de las células solares de concentración III-V. En base a este análisis se presenta la planificación de los trabajos realizados en esta Tesis Doctoral. A partir de esta planificación y debido a la necesidad de adaptar, mejorar e innovar las técnicas de ensayos de vida acelerada para una adecuada aplicación a este tipo de dispositivos, en el capítulo 5 se muestra la metodología empleada y la instrumentación necesaria para realizar los ensayos de esta Tesis Doctoral. El núcleo de la memoria es el capítulo 6, en él se presentan los resultados de caracterización de las células durante los ensayos de vida acelerada y el análisis de dichos resultados con el objetivo de obtener valores cuantitativos de fiabilidad en condiciones reales de trabajo. Se calcula el Factor de Aceleración de los ensayos acelerados con respecto a las condiciones nominales de funcionamiento a partir de la Energía de Activación obtenida, y se demuestra la validez de la metodología y cálculos empleados, que son la base de la evaluación de la fiabilidad. Finalmente se calculan valores cuantitativos de degradación, fiabilidad y garantía de las células en condiciones nominales en campo durante toda la vida de la célula. Con el desarrollo de esta Tesis Doctoral se ha evaluado la fiabilidad de células III-V de área pequeña, pero es muy interesante generalizar los procedimientos aquí desarrollados para las células III-V comerciales de área grande. Por este motivo, en el capítulo 7 se analiza dicha generalización, incluyendo el modelado térmico mediante elementos finitos de los circuitos de ensayo de las células. En el último capítulo se realiza un resume del trabajo y las aportaciones realizadas, y se identifican las líneas de trabajo a emprender en el futuro.

Microprocesos láser para la mejora de dispositivos fotovoltaicos basados en silicio cristalino

En los últimos años la tecnología láser se ha convertido en una herramienta imprescindible en la fabricación de dispositivos fotovoltaicos, ayudando a la consecución de dos objetivos claves para que esta opción energética se convierta en una alternativa viable: reducción de costes de fabricación y aumento de eficiencia de dispositivo. Dentro de las tecnologías fotovoltaicas, las basadas en silicio cristalino (c-Si) siguen siendo las dominantes en el mercado, y en la actualidad los esfuerzos científicos en este campo se encaminan fundamentalmente a conseguir células de mayor eficiencia a un menor coste encontrándose, como se comentaba anteriormente, que gran parte de las soluciones pueden venir de la mano de una mayor utilización de tecnología láser en la fabricación de los mismos. En este contexto, esta Tesis hace un estudio completo y desarrolla, hasta su aplicación en dispositivo final, tres procesos láser específicos para la optimización de dispositivos fotovoltaicos de alta eficiencia basados en silicio. Dichos procesos tienen como finalidad la mejora de los contactos frontal y posterior de células fotovoltaicas basadas en c-Si con vistas a mejorar su eficiencia eléctrica y reducir el coste de producción de las mismas. En concreto, para el contacto frontal se han desarrollado soluciones innovadoras basadas en el empleo de tecnología láser en la metalización y en la fabricación de emisores selectivos puntuales basados en técnicas de dopado con láser, mientras que para el contacto posterior se ha trabajado en el desarrollo de procesos de contacto puntual con láser para la mejora de la pasivación del dispositivo. La consecución de dichos objetivos ha llevado aparejado el alcanzar una serie de hitos que se resumen continuación: - Entender el impacto de la interacción del láser con los distintos materiales empleados en el dispositivo y su influencia sobre las prestaciones del mismo, identificando los efectos dañinos e intentar mitigarlos en lo posible. - Desarrollar procesos láser que sean compatibles con los dispositivos que admiten poca afectación térmica en el proceso de fabricación (procesos a baja temperatura), como los dispositivos de heterounión. - Desarrollar de forma concreta procesos, completamente parametrizados, de definición de dopado selectivo con láser, contactos puntuales con láser y metalización mediante técnicas de transferencia de material inducida por láser. - Definir tales procesos de forma que reduzcan la complejidad de la fabricación del dispositivo y que sean de fácil integración en una línea de producción. - Mejorar las técnicas de caracterización empleadas para verificar la calidad de los procesos, para lo que ha sido necesario adaptar específicamente técnicas de caracterización de considerable complejidad. - Demostrar su viabilidad en dispositivo final. Como se detalla en el trabajo, la consecución de estos hitos en el marco de desarrollo de esta Tesis ha permitido contribuir a la fabricación de los primeros dispositivos fotovoltaicos en España que incorporan estos conceptos avanzados y, en el caso de la tecnología de dopado con láser, ha permitido hacer avances completamente novedosos a nivel mundial. Asimismo los conceptos propuestos de metalización con láser abren vías, completamente originales, para la mejora de los dispositivos considerados. Por último decir que este trabajo ha sido posible por una colaboración muy estrecha entre el Centro Láser de la UPM, en el que la autora desarrolla su labor, y el Grupo de Investigación en Micro y Nanotecnologías de la Universidad Politécnica de Cataluña, encargado de la preparación y puesta a punto de las muestras y del desarrollo de algunos procesos láser para comparación. También cabe destacar la contribución de del Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, CIEMAT, en la preparación de experimentos específicos de gran importancia en el desarrollo del trabajo. Dichas colaboraciones se han desarrollado en el marco de varios proyectos, tales como el proyecto singular estratégico PSE-MICROSIL08 (PSE-iv 120000-2006-6), el proyecto INNDISOL (IPT-420000-2010-6), ambos financiados por el Fondo Europeo de Desarrollo Regional FEDER (UE) “Una manera de hacer Europa” y el MICINN, y el proyecto del Plan Nacional AMIC (ENE2010-21384-C04-02), cuya financiación ha permitido en gran parte llevar a término este trabajo. v ABSTRACT. Last years lasers have become a fundamental tool in the photovoltaic (PV) industry, helping this technology to achieve two major goals: cost reduction and efficiency improvement. Among the present PV technologies, crystalline silicon (c-Si) maintains a clear market supremacy and, in this particular field, the technological efforts are focussing into the improvement of the device efficiency using different approaches (reducing for instance the electrical or optical losses in the device) and the cost reduction in the device fabrication (using less silicon in the final device or implementing more cost effective production steps). In both approaches lasers appear ideally suited tools to achieve the desired success. In this context, this work makes a comprehensive study and develops, until their implementation in a final device, three specific laser processes designed for the optimization of high efficiency PV devices based in c-Si. Those processes are intended to improve the front and back contact of the considered solar cells in order to reduce the production costs and to improve the device efficiency. In particular, to improve the front contact, this work has developed innovative solutions using lasers as fundamental processing tools to metalize, using laser induced forward transfer techniques, and to create local selective emitters by means of laser doping techniques. On the other side, and for the back contact, and approached based in the optimization of standard laser fired contact formation has been envisaged. To achieve these fundamental goals, a number of milestones have been reached in the development of this work, namely: - To understand the basics of the laser-matter interaction physics in the considered processes, in order to preserve the functionality of the irradiated materials. - To develop laser processes fully compatible with low temperature device concepts (as it is the case of heterojunction solar cells). - In particular, to parameterize completely processes of laser doping, laser fired contacts and metallization via laser transfer of material. - To define such a processes in such a way that their final industrial implementation could be a real option. - To improve widely used characterization techniques in order to be applied to the study of these particular processes. - To probe their viability in a final PV device. Finally, the achievement of these milestones has brought as a consequence the fabrication of the first devices in Spain incorporating these concepts. In particular, the developments achieved in laser doping, are relevant not only for the Spanish science but in a general international context, with the introduction of really innovative concepts as local selective emitters. Finally, the advances reached in the laser metallization approached presented in this work open the door to future developments, fully innovative, in the field of PV industrial metallization techniques. This work was made possible by a very close collaboration between the Laser Center of the UPM, in which the author develops his work, and the Research Group of Micro y Nanotecnology of the Universidad Politécnica de Cataluña, in charge of the preparation and development of samples and the assessment of some laser processes for comparison. As well is important to remark the collaboration of the Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, CIEMAT, in the preparation of specific experiments of great importance in the development of the work. These collaborations have been developed within the framework of various projects such as the PSE-MICROSIL08 (PSE-120000-2006-6), the project INNDISOL (IPT-420000-2010-6), both funded by the Fondo Europeo de Desarrollo Regional FEDER (UE) “Una manera de hacer Europa” and the MICINN, and the project AMIC (ENE2010-21384-C04-02), whose funding has largely allowed to complete this work.