Comparative studies on growth of fry of GIFT and Existing strain of Nile tilapia (Oreochromis niloticus L.)

Comparative study on growth of fry in nursery system of Genetically Improved Farmed Tilapia (GIFT) and Existing strain of Nile tilapia (Oreochromis niloticus) was performed. The trials were conducted in a series of hapa for two months. The initial mean weight of GIFT and Existing strains of tilapia were 1.03 and 1.12g, respectively and the stocking density for both the strains was maintained at 150/m³. Fishes were fed with supplementary feed 31.29% of protein level. After two months the final cumulative mean weight of GIFT and Existing strain were observed to be 8.38 and 5.51g, respectively. The net gain for weight of GIFT and existing strain were estimated to be 666% and 368% and the mean survival were 95.75% and 81.25%, respectively. The GIFT strain showed significantly (P<0.05) higher net gain in growth in weight and also higher (P<0.01) survival than that of existing strain.

Yielding of engineering polymers at strain rates of up to 500 s-1

A method is described for measuring the mechanical properties of polymers in compression at strain rates in the range approximately 300-500 s-1. A gravity-driven pendulum is used to load a specimen on the end of an instrumented Hopkinson output bar and the results are processed by a microcomputer. Stress-strain curves up to high strains are presented for polycarbonate, polyethersulphone and high density polyethylene over a range of temperatures. The value of yield stress, for all three polymers, was found to vary linearly with log (strain rate) at strain rates up to 500 s-1. © 1985.

Distributed optical fiber strain sensing in a secant piled wall

An optical fiber strain sensing technique, based on Brillouin Optical Time Domain Reflectometry (BOTDR), was used to obtain the full deformation profile of a secant pile wall during construction of an adjacent basement in London. Details of the installation of sensors as well as data processing are described. By installing optical fiber down opposite sides of the pile, the distributed strain profiles obtained can be used to give both the axial and lateral movements along the pile. Measurements obtained from the BOTDR were found in good agreement with inclinometer data from the adjacent piles. The relative merits of the two different techniques are discussed. © 2007 ASCE.

Monitoring tunnel deformation induced by close-proximity bored tunneling using distributed optical fiber strain measurements

The paper describes the use of optical fiber Brillouin Optical Time Domain Reflectometry (BOTDR) to monitor the strain distribution in an existing tunnel while a twin tunnel was bored at close-proximity. The twin circular bored tunnels between Serangoon and Bartley stations on the new Circle Line Stage 3 subway in Singapore were constructed at close-proximity to avoid underpinning the foundations of adjacent buildings. The minimum clear separation of the two tunnels is 2.3m (0.4 times the tunnel diameter). The Outer Tunnel was constructed first, followed by the Inner Tunnel, with the earth-pressure balance tunnel boring machines maintained at a minimum of 100m apart. In this trial application of BOTDR, the strain distribution along the Outer Tunnel was measured, in order to monitor its deformation due to the boring of the Inner Tunnel at close-proximity. The aim of the trial application was to determine the practicality of this monitoring method for future use in 'live' tunnels. This paper compares the measurements obtained from optical fiber BOTDR with conventional methods of tunnel monitoring and describes preliminary installation and workmanship guidelines derived from lessons learnt during this trial. © 2007 ASCE.

A packaging technique for silicon MEMS strain sensors on steel

A packaging technique suited to applying MEMS strain sensors realized on a silicon chip to a steel flat surface is described. The method is based on adhesive bonding of the silicon chip rear surface on steel using two types of glue normally used for standard piezoresistive strain sensors (Mbond200/ 600), using direct wire bonding of the chip to a Printed Circuit Board, also fixed on steel. In order to protect the sensor from the external environment, and to improve the MEMS performance, the silicon chip is encapsulated with a metal cap hermetically sealed-off under vacuum condition with a vacuum adhesive in which the bonding wires are also protected from possible damage. In order to evaluate the mechanical coupling of the silicon chip with the bar and thestress transfer extent to the silicon surface, commercial strain sensors have been applied on the chip glued on a steel bar in alaboratory setup able to generate strain by inflection, yielding a stress transfer around 70% from steel to silicon. © 2008 IEEE.

Breeding biology and monosex male seed production of Genetically Improved Farmed Tilapia (GIFT) strain of Oreochromis niloticus L. in Bangladesh

A study on the breeding biology of the GIFT strain of Nile tilapia, Oreochromis niloticus, was conducted for a period of five months. The sex ratio of the parent individuals was optimized for performance in spawn production, where the best results were obtained with a sex ratio of female to male of 4:1 compared to those of 3:1 and 2:1. The diameter of eggs obtained from the GIFT stock had major and minor axes of 2.19±0.09 and 1.72±0.07 mm, respectively, with no significant differences between the treatments. The average number of eggs produced was 392±22 per female, with fertilization and hatching rates ranging between 94-96% and 85-88%, respectively. No significant variation was observed between the treatments. Breeding frequencies per female in the three treatment groups ranged between 10-40 days and the highest value was obtained at a female to male sex ratio of 4: l. In an other experiment, l7 aMethyltestosterone (MT) was applied orally to the fry at their first feeding stage with treatments- 1, 2, 3 and 4 at the dosage of 100, 80, 60 and 40 mg/kg feed respectively, for the period of 28 days. The mean percentage of males obtained in treatments, 1, 2, 3 and 4 were 98, 97, 95 and 68, respectively. Treatments-1, 2 and 3 did not differ significantly (P>0.05) from each other but treatment 4 showed significant variation (P<0.05) from other treatments. The results showed that MT-100, 80 and 60 mg/kg feed administered for 28 days produced close to cent percent male population of the GIFT strains in aquaria.

Growth performance, recovery rate and fish yield of GIFT strain at various water depths under rice-fish culture systems

Effect of water depth on recovery rate, growth performance and fish yield of GIFT in the rice-fish production systems was studies in experimental plots of 123 m2 with a pond refuge of I meter deep which covered 10% of the total land area. Mortality rate of fish was very low ranging from 0.81-1.63%. However, at harvest, recovery rate ranged from 76.69-82.93% with the highest recovery at 11-15 em of water depth. Significantly the highest absolute growth (99.97) and specific growth rate (2.42%) were found at 21-25 cm water depth. The same treatment also produced significantly higher fish yield (909.76 kg/ha) although statistically similar to the fish yield (862.60 kg/ha) obtained at ll-15 em of water depth. Results also suggested that higher water depth can produce bigger fish but no significant effects of water depth was found on fish yield in the treatments 11-15 cm and 21-25 cm water depths of this experiment.

Establishment of satellite nucleus of genetically improved farmed tilapia (GIFT strain) in Bangladesh

The aim of this study was to evaluate growth performance of the GIFT (Genetically Improved Farmed Tilapia) strain after one generation of selection for increased body weight at Bangladesh Fisheries Research Institute. Founder stock comprised of 30 families having 300 individuals of the GIFT strain were introduced from Malaysia through \X!orldFish Center in March 2005. The founder stock was reared in 100 m2 hapa for three months and then individually tagged using Passive Integrated Transponder (PIT) at the weight between 30 and 40 g. After tagging, all the fish were communally grown out in pond until harvest. Breeding value for body weight was estimated using SAS and ASREML ranging from 4.17 to 9.70 g for males and 4.24 to 9.36 g for females. The best 40 females and 40 males from the founder stock were then selected to produce progeny of the first generation (F-1). From each family 25 female and 25 male fingerlings were sampled and tagged using PIT. A total of 2,000 tagged fish from 40 families were stocked in a pond (1000 m2) for a continuation of the selection program. In addition, surplus fish after tagging were also reared together with progeny of the founder stock in cistern ecology for growth evaluation. The mean weight of the F-1 generation of GIFT fish was 7.2% greater than that of the founder population (non selected population).

Fabrication and testing of a high resolution extensometer based on resonant MEMS strain sensors

A novel type of linear extensometer with exceptionally high resolution of 4 nm based on MEMS resonant strain sensors bonded on steel and operating in a vacuum package is presented. The tool is implemented by means of a steel thin bar that can be pre-stressed in tension within two fixing anchors. The extension of the bar is detected by using two vacuum-packaged resonant MEMS double- ended tuning fork (DETF) sensors bonded on the bar with epoxy glue, one of which is utilized for temperature compensation. Both sensors are driven by a closed loop self-oscillating transresistance amplifier feedback scheme implemented on a PCB (Printed Circuit Board). On the same board, a microcontroller-based frequency measurement circuit is also implemented, which is able to count the square wave fronts of the MEMS oscillator output with a resolution of 20 nsec. The system provides a frequency noise of 0.2 Hz corresponding to an extension resolution of 4 nm for the extensometer. Nearly perfect temperature compensation of the frequency output is achieved in the temperature range 20-35 C using the reference sensor. © 2011 IEEE.