Application of the Extended Kalman filter to fuzzy modeling: Algorithms and practical implementation

Modeling phase is fundamental both in the analysis process of a dynamic system and the design of a control system. If this phase is in-line is even more critical and the only information of the system comes from input/output data. Some adaptation algorithms for fuzzy system based on extended Kalman filter are presented in this paper, which allows obtaining accurate models without renounce the computational efficiency that characterizes the Kalman filter, and allows its implementation in-line with the process

Robustness Analysis of Eigenstructure Assignment Controllers on Rigid-Flexible Satellites

Flexible spacecraft with attached solar panels may exhibit undesired vibrations and structural deformations. These types of vehicles show an intrinsic coupling of the elements of the structure. The attitude maneuvers performed by flexible spacecraft may cause non-desired deflections of attached flexible elements. Any attitude and orbit control system generally solves these problems using filters that are designed to attenuate the relative deflections of flexible appendages. In this paper, we propose a method for designing attitude static controllers using an eigenstructure assignment (EA) method. A set of requirements were specified from our understanding of the system modes in an open loop. Exhaustive theoretical and numerical simulations were performed on special cases to verify the controller design procedure. In the design of the controller, we considered all of the aspects that relate to the eigenstructure assignment. The primary objective of this paper is to demonstrate the feasibility of obtaining a high degree of decoupling for some selected modes via the application of an EA method. Finally a robustness analysis is perform to the system together with the designed controller by means of a mu-analysis

Diseño de un sistema de climatización para un edificio singular mediante el uso de fuentes de energía renovable

El proyecto consiste en el diseño del sistema de climatización de un edificio ubicado en la ciudad de Madrid que utilice la energía solar como fuente de calor y electricidad. El objetivo es que el edificio tenga un consumo energético lo más bajo posible y que utilice energías de origen renovable para su explotación. Se incluye el cálculo de cargas térmicas, el dimensionamiento del sistema de climatización y de los sistemas de captación de energía solar (térmica y fotovoltaica). Adicionalmente, se definen las principales características de un sistema de control centralizado que permita optimizar el rendimiento y monitorizar el funcionamiento de la instalación de forma continua. Se incluye el diseño de las instalaciones auxiliares con un grado de detalle suficiente que permita su valoración, tanto desde el punto de vista energético como económico. Como parte fundamental del proyecto, se extraen conclusiones acerca del ahorro energético de las instalaciones y se analiza la viabilidad económica de las inversiones. ABSTRACT The project covers the design of a Heating and Climatization System for a building located in the city of Madrid (Spain). The facilities will use solar energy as the main source for both heat and electricity. The main goals are to achieve the lowest possible energy consumption and to use renewable sources of energy to cover it. Calculation of thermal charges is included, together with the sizing of both the Climatization System and the Solar Energy (Thermal and PV) facilities. In addition, the main characteristics of a Centralized Control System are defined. This will help both to optimize the performance of the different systems involved and to monitor the operation. Design of all auxiliary systems is included with enough level of detail as to be able to evaluate them from both energetic and economic points of view. Paramount in this project is to be able to draw conclusions about the energy savings and the profitability (or not) of the main investments to be carried out

Neural network controller for active demand side management with PV energy in the residential sector

In this paper, we describe the development of a control system for Demand-Side Management in the residential sector with Distributed Generation. The electrical system under study incorporates local PV energy generation, an electricity storage system, connection to the grid and a home automation system. The distributed control system is composed of two modules: a scheduler and a coordinator, both implemented with neural networks. The control system enhances the local energy performance, scheduling the tasks demanded by the user and maximizing the use of local generation.

Analysis of WCET in an experimental satellite software development.

This paper describes a case study in WCET analysis of an on-board spacecraft software system. The attitude control system of UPMSat-2, an experimental micro-satellite which is scheduled to be launched in 2013, is used for an experiment on analysing the worst-case execution time of code automatically generated from a Simulink model. In order to properly test the code, a hardware-in-the-loop configuration with a simulation model of the spacecraft environment has been used as a test bench. The code has been analysed with RapiTime, with some modifications to the original instrumentation routines, in order to take into account the particularities of the test configuration. Results from the experiment are described and commented in the paper.

Diseño de un sistema automático de medida de la constante de Planck en diodos LED

En este proyecto fin de carrera se ha diseñado y construido un equipo de medida automático que permite realizar la medida de la constante de Planck utilizando los principios de Funcionamiento de los diodos LED. El equipo de medida es totalmente automático gracias a la utilización de una placa controladora Arduino MEGA 2560, que se encarga de realizar la iluminación secuencial de cada LED, medir sus tensiones de funcionamiento, y de realizar los cálculos necesarios para hallar la constante de Planck. Todos los datos se muestran por una pantalla LCD de 16 caracteres por 2 lineas. Para comprender el funcionamiento del sistema de medida automático se ha realizado un estudio detallado de cada uno de los sistemas que componen el equipo de medida. Se ha explicado el funcionamiento teórico de los diodos LED y el funcionamiento de los semiconductores. Se ha explicando los diversos tipos de semiconductores que se utilizan para los LED y las modificaciones que se les aplica para mejorar su eficiencia. Para poder comprender en qué consiste la constante de Planck se ha explicado los principios teóricos en que se basa, y se ha realizado una pequeña demostración de su cálculo. Una vez visto todos los principios teóricos se ha pasado a realizar la explicación de cada uno de los grandes bloques que componen el sistema de medida automático. Estos bloques son la placa controladora Arduino, el sistema de iluminación LED, el sistema de control mecánico de LEDs, la pantalla LCD, el sistema de interrupciones y el sistema de alimentación. Para poder observar el espectro de emisión de cada uno de los LED se ha utilizado un analizador de espectros óptico (OSA), el cual ha sido explicado con detenimiento. El código de programación de Arduino ha sido explicado en forma de diagrama de flujo para una mayor facilidad de comprensión. Se ha desarrollado un manual de usuario para facilitar el uso del sistema a cualquier usuario, en el que se ha introducido un ejemplo completo de funcionamiento. ABSTRACT. In this final Project has designed and built an automatic measuring equipment which is able to measure the Planck`s constant using the operation principles of the LEDs. The measuring equipment is fully automated thanks to the use of an Arduino Mega 2560 controller board, which is responsible for conducting sequential illumination of each LED, measure their operating voltages, and perform the necessary calculations of find the Planck constant. All data is displayed by a LCD screen 16 character by 2 lines. To understand the operation of the automatic measuring system has been made a detailed study of each of the systems that make the measurement equipment. It develops the theoretical performance of the LED and the operation of semiconductors. It explains the different types of semiconductors that are used for LEDs and the changes applied to improve efficiency. In order to understand what is the Planck constant has been explained the theoretical principles in which it is based, and a small demonstration of its calculation has been performed. After seeing all the theoretical principles has been made the explanation of each of the main blocks that compose the automatic measuring system. These blocks are the Arduino controller board, LED lighting system, the mechanical control system LEDs, LCD screen, the interrupt system and feeding system. To observe the emission spectrum of each of the LED has been used optical spectrum analyzer (OSA), which has been explained in detail. The Arduino programming code has been explained in flowchart form for an easy understanding. It has developed a manual to facilitate the use of system to any user, which has introduced a complete example of operation.

Desarrollo de manejadores de dispositivos para el computador del UPMSat-2

En el presente Trabajo de Fin de Grado se abordan diferentes aspectos del diseño, implementación y vericación de un sistema de tiempo real de características especiales, el satélite UPMSat-2. Este proyecto, llevado a cabo por un grupo de trabajo formado por profesores, alumnos y personal de la Universidad Politecnica de Madrid (UPM), tiene como objetivo el desarrollo de un microsatélite como plataforma de demostración tecnológica en órbita. Parte de este grupo de trabajo es el Grupo de Sistemas de Tiempo Real y Arquitectura de Servicios Telemáticos (STRAST), del cual el alumno forma parte y que tiene a cargo el diseño e implementación tanto del software de abordo como del software de tierra. Dentro de estas asignaciones, el alumno ha trabajado en tres aspectos principales: el diseño e implementación de diferentes manejadores de dispositivos, el diseño de un algoritmo para la gestión de la memoria no volátil y la configuración y prueba de un sistema de validación de software para un subsistema del satélite. Tanto la memoria de estas tareas como las bases y fundamentos tecnológicos aplicados se desarrollan en el documento. ------------------------------------------------ ----------------------------------------------------------------------------------- Diferent aspects of the design, implementation and validation of an specific Real Time System, the UPMSat-2 satellite, are described in this final report. UPMSat-2 project is aimed at developing an experimental microsatellite that can be used as a technology demonstrator for several research groups at UPM. The Real-Time Systems Group at UPM (STRAST) is responsible for designing and building all the on-board and ground-segment software for the satellite. In relation to this, three main task have been carried out and are described in this document: the design and implementation of three diferent device drivers, the design of an algorithm to manage the nonvolatile memory and the configuration and test of a software validation facility to test the UPMSat-2 Attitude Determination and Control System (ADCS) subsystem. Detailed information of these tasks and their technological basis are presented in the rest of the document.

Model-based Self-awareness Patterns for Autonomy

Los sistemas técnicos son cada vez más complejos, incorporan funciones más avanzadas, están más integrados con otros sistemas y trabajan en entornos menos controlados. Todo esto supone unas condiciones más exigentes y con mayor incertidumbre para los sistemas de control, a los que además se demanda un comportamiento más autónomo y fiable. La adaptabilidad de manera autónoma es un reto para tecnologías de control actualmente. El proyecto de investigación ASys propone abordarlo trasladando la responsabilidad de la capacidad de adaptación del sistema de los ingenieros en tiempo de diseño al propio sistema en operación. Esta tesis pretende avanzar en la formulación y materialización técnica de los principios de ASys de cognición y auto-consciencia basadas en modelos y autogestión de los sistemas en tiempo de operación para una autonomía robusta. Para ello el trabajo se ha centrado en la capacidad de auto-conciencia, inspirada en los sistemas biológicos, y se ha explorado la posibilidad de integrarla en la arquitectura de los sistemas de control. Además de la auto-consciencia, se han explorado otros temas relevantes: modelado funcional, modelado de software, tecnología de los patrones, tecnología de componentes, tolerancia a fallos. Se ha analizado el estado de la técnica en los ámbitos pertinentes para las cuestiones de la auto-consciencia y la adaptabilidad en sistemas técnicos: arquitecturas cognitivas, control tolerante a fallos, y arquitecturas software dinámicas y computación autonómica. El marco teórico de ASys existente de sistemas autónomos cognitivos ha sido adaptado para servir de base para este análisis de autoconsciencia y adaptación y para dar sustento conceptual al posterior desarrollo de la solución. La tesis propone una solución general de diseño para la construcción de sistemas autónomos auto-conscientes. La idea central es la integración de un meta-controlador en la arquitectura de control del sistema autónomo, capaz de percibir la estado funcional del sistema de control y, si es necesario, reconfigurarlo en tiempo de operación. Esta solución de metacontrol se ha formalizado en cuatro patrones de diseño: i) el Patrón Metacontrol, que define la integración de un subsistema de metacontrol, responsable de controlar al propio sistema de control a través de la interfaz proporcionada por su plataforma de componentes, ii) el patrón Bucle de Control Epistémico, que define un bucle de control cognitivo basado en el modelos y que se puede aplicar al diseño del metacontrol, iii) el patrón de Reflexión basada en Modelo Profundo propone una solución para construir el modelo ejecutable utilizado por el meta-controlador mediante una transformación de modelo a modelo a partir del modelo de ingeniería del sistema, y, finalmente, iv) el Patrón Metacontrol Funcional, que estructura el meta-controlador en dos bucles, uno para el control de la configuración de los componentes del sistema de control, y otro sobre éste, controlando las funciones que realiza dicha configuración de componentes; de esta manera las consideraciones funcionales y estructurales se desacoplan. La Arquitectura OM y el metamodelo TOMASys son las piezas centrales del marco arquitectónico desarrollado para materializar la solución compuesta de los patrones anteriores. El metamodelo TOMASys ha sido desarrollado para la representación de la estructura y su relación con los requisitos funcionales de cualquier sistema autónomo. La Arquitectura OM es un patrón de referencia para la construcción de una metacontrolador integrando los patrones de diseño propuestos. Este meta-controlador se puede integrar en la arquitectura de cualquier sistema control basado en componentes. El elemento clave de su funcionamiento es un modelo TOMASys del sistema decontrol, que el meta-controlador usa para monitorizarlo y calcular las acciones de reconfiguración necesarias para adaptarlo a las circunstancias en cada momento. Un proceso de ingeniería, complementado con otros recursos, ha sido elaborado para guiar la aplicación del marco arquitectónico OM. Dicho Proceso de Ingeniería OM define la metodología a seguir para construir el subsistema de metacontrol para un sistema autónomo a partir del modelo funcional del mismo. La librería OMJava proporciona una implementación del meta-controlador OM que se puede integrar en el control de cualquier sistema autónomo, independientemente del dominio de la aplicación o de su tecnología de implementación. Para concluir, la solución completa ha sido validada con el desarrollo de un robot móvil autónomo que incorpora un meta-controlador con la Arquitectura OM. Las propiedades de auto-consciencia y adaptación proporcionadas por el meta-controlador han sido validadas en diferentes escenarios de operación del robot, en los que el sistema era capaz de sobreponerse a fallos en el sistema de control mediante reconfiguraciones orquestadas por el metacontrolador. ABSTRACT Technical systems are becoming more complex, they incorporate more advanced functionalities, they are more integrated with other systems and they are deployed in less controlled environments. All this supposes a more demanding and uncertain scenario for control systems, which are also required to be more autonomous and dependable. Autonomous adaptivity is a current challenge for extant control technologies. The ASys research project proposes to address it by moving the responsibility for adaptivity from the engineers at design time to the system at run-time. This thesis has intended to advance in the formulation and technical reification of ASys principles of model-based self-cognition and having systems self-handle at runtime for robust autonomy. For that it has focused on the biologically inspired capability of self-awareness, and explored the possibilities to embed it into the very architecture of control systems. Besides self-awareness, other themes related to the envisioned solution have been explored: functional modeling, software modeling, patterns technology, components technology, fault tolerance. The state of the art in fields relevant for the issues of self-awareness and adaptivity has been analysed: cognitive architectures, fault-tolerant control, and software architectural reflection and autonomic computing. The extant and evolving ASys Theoretical Framework for cognitive autonomous systems has been adapted to provide a basement for this selfhood-centred analysis and to conceptually support the subsequent development of our solution. The thesis proposes a general design solution for building self-aware autonomous systems. Its central idea is the integration of a metacontroller in the control architecture of the autonomous system, capable of perceiving the functional state of the control system and reconfiguring it if necessary at run-time. This metacontrol solution has been formalised into four design patterns: i) the Metacontrol Pattern, which defines the integration of a metacontrol subsystem, controlling the domain control system through an interface provided by its implementation component platform, ii) the Epistemic Control Loop pattern, which defines a modelbased cognitive control loop that can be applied to the design of such a metacontroller, iii) the Deep Model Reflection pattern proposes a solution to produce the online executable model used by the metacontroller by model-to-model transformation from the engineering model, and, finally, iv) the Functional Metacontrol pattern, which proposes to structure the metacontroller in two loops, one for controlling the configuration of components of the controller, and another one on top of the former, controlling the functions being realised by that configuration; this way the functional and structural concerns become decoupled. The OM Architecture and the TOMASys metamodel are the core pieces of the architectural framework developed to reify this patterned solution. The TOMASys metamodel has been developed for representing the structure and its relation to the functional requirements of any autonomous system. The OM architecture is a blueprint for building a metacontroller according to the patterns. This metacontroller can be integrated on top of any component-based control architecture. At the core of its operation lies a TOMASys model of the control system. An engineering process and accompanying assets have been constructed to complete and exploit the architectural framework. The OM Engineering Process defines the process to follow to develop the metacontrol subsystem from the functional model of the controller of the autonomous system. The OMJava library provides a domain and application-independent implementation of an OM Metacontroller than can be used in the implementation phase of OMEP. Finally, the complete solution has been validated in the development of an autonomous mobile robot that incorporates an OM metacontroller. The functional selfawareness and adaptivity properties achieved thanks to the metacontrol system have been validated in different scenarios. In these scenarios the robot was able to overcome failures in the control system thanks to reconfigurations performed by the metacontroller.

Measuring skin temperature before, during and after exercise: a comparison of thermocouples and infrared thermography

Measuring skin temperature (TSK) provides important information about the complex thermal control system and could be interesting when carrying out studies about thermoregulation. The most common method to record TSK involves thermocouples at specific locations; however, the use of infrared thermal imaging (IRT) has increased. The two methods use different physical processes to measure TSK, and each has advantages and disadvantages. Therefore, the objective of this study was to compare the mean skin temperature (MTSK) measurements using thermocouples and IRT in three different situations: pre-exercise, exercise and post-exercise. Analysis of the residual scores in Bland-Altman plots showed poor agreement between the MTSK obtained using thermocouples and those using IRT. The averaged error was -0.75 °C during pre-exercise, 1.22 °C during exercise and -1.16 °C during post-exercise, and the reliability between the methods was low in the pre- (ICC = 0.75 [0.12 to 0.93]), during (ICC = 0.49 [-0.80 to 0.85]) and post-exercise (ICC = 0.35 [-1.22 to 0.81] conditions. Thus, there is poor correlation between the values of MTSK measured by thermocouples and IRT pre-exercise, exercise and post-exercise, and low reliability between the two forms of measurement.

Home automation controller for a water-flow window

Facing the EU energy efficiency and legal scenarios related to buildings (2010/31 EU directive), new sustainable advanced concepts for envelopes are required. These innovative designs must be able to offer an elevated level of energy efficiency based on a high performance architecture. According to this, smart glazings, and particularly active water-flow glazings, represent a promising alternative to other solar control glazings, since they can reduce the building energy demand avoiding well known drawbacks as high cost, glare problems and high response time that affect to other smart glazings. This kind of glazing, as any other active one, needs to be operated by a control system. In order to operate a water-flow based window, a new controller based on an inexpensive microcontroller board has been developed

Licensing patterns for Linked Data

Rights expression languages declare the permitted and prohibited actions to be performed on a resource. Along this work, six rights expression languages are compared, abstracting their commonalities and outlining their underlying pattern. Linked Data, which can be object of protection by the intellectual property laws or its access be restricted by an access control system, can be the asset in rights expressions. The requirements for a pattern for licensing Linked Data resources are listed.

Offline GA-Based optimization for heterogeneous modular multi-configurable chained microrobots

This paper presents a GA-based optimization procedure for bioinspired heterogeneous modular multiconfigurable chained microrobots. When constructing heterogeneous chained modular robots that are composed of several different drive modules, one must select the type and position of the modules that form the chain. One must also develop new locomotion gaits that combine the different drive modules. These are two new features of heterogeneous modular robots that they do not share with homogeneous modular robots. This paper presents an offline control system that allows the development of new configuration schemes and locomotion gaits for these heterogeneous modular multiconfigurable chained microrobots. The offline control system is based on a simulator that is specifically designed for chained modular robots and allows them to develop and learn new locomotion patterns.

Discriminación del estado de la carretera mediante procesado acústico en vehículo

La rápida adopción de dispositivos electrónicos en el automóvil, ha contribuido a mejorar en gran medida la seguridad y el confort. Desde principios del siglo 20, la investigación en sistemas de seguridad activa ha originado el desarrollo de tecnologías como ABS (Antilock Brake System), TCS (Traction Control System) y ESP (Electronic Stability Program). El coste de despliegue de estos sistemas es crítico: históricamente, sólo han sido ampliamente adoptados cuando el precio de los sensores y la electrónica necesarios para su construcción ha caído hasta un valor marginal. Hoy en día, los vehículos a motor incluyen un amplio rango de sensores para implementar las funciones de seguridad. La incorporación de sistemas que detecten la presencia de agua, hielo o nieve en la vía es un factor adicional que podría ayudar a evitar situaciones de riesgo. Existen algunas implementaciones prácticas capaces de detectar carreteras mojadas, heladas y nevadas, aunque con limitaciones importantes. En esta tesis doctoral, se propone una aproximación novedosa al problema, basada en el análisis del ruido de rodadura generado durante la conducción. El ruido de rodadura es capturado y preprocesado. Después es analizado utilizando un clasificador basado en máquinas de vectores soporte (SVM), con el fin de generar una estimación del estado del firme. Todas estas operaciones se realizan en el propio vehículo. El sistema propuesto se ha desarrollado y evaluado utilizando Matlabr, mostrando tasas de aciertos de más del 90%. Se ha realizado una implementación en tiempo real, utilizando un prototipo basado en DSP. Después se han introducido varias optimizaciones para permitir que el sistema sea realizable usando un microcontrolador de propósito general. Finalmente se ha realizado una implementación hardware basada en un microcontrolador, integrándola estrechamente con las ECU del vehículo, pudiendo obtener datos capturados por los sensores del mismo y enviar las estimaciones del estado del firme. El sistema resultante ha sido patentado, y destaca por su elevada tasa de aciertos con un tamaño, consumo y coste reducidos. ABSTRACT Proliferation of automotive electronics, has greatly improved driving safety and comfort. Since the beginning of the 20th century, investigation in active safety systems has resulted in the development of technologies such as ABS (Antilock Brake System), TCS (Traction Control System) and ESP (Electronic Stability Program). Deployment cost of these systems is critical: historically, they have been widely adopted only when the price of the sensors and electronics needed to build them has been cut to a marginal value. Nowadays, motor vehicles include a wide range of sensors to implement the safety functions. Incorporation of systems capable of detecting water, ice or snow on the road is an additional factor that could help avoiding risky situations. There are some implementations capable of detecting wet, icy and snowy roads, although with important limitations. In this PhD Thesis, a novel approach is proposed, based on the analysis of the tyre/road noise radiated during driving. Tyre/road noise is captured and pre-processed. Then it is analysed using a Support Vector Machine (SVM) based classifier, to output an estimation of the road status. All these operations are performed on-board. Proposed system is developed and evaluated using Matlabr, showing success rates greater than 90%. A real time implementation is carried out using a DSP based prototype. Several optimizations are introduced enabling the system to work using a low-cost general purpose microcontroller. Finally a microcontroller based hardware implementation is developed. This implementation is tightly integrated with the vehicle ECUs, allowing it to obtain data captured by its sensors, and to send the road status estimations. Resulting system has been patented, and is notable because of its high hit rate, small size, low power consumption and low cost.

Stability Analysis of a Run-of-River Diversion Hydropower Plant With Surge Tank And Spillway in the Head Pond

Run-of-river hydropower plants usually lack significant storage capacity; therefore, the more adequate control strategy would consist of keeping a constant water level at the intake pond in order to harness the maximum amount of energy from the river flow or to reduce the surface flooded in the head pond. In this paper, a standard PI control system of a run-of-river diversion hydropower plant with surge tank and a spillway in the head pond that evacuates part of the river flow plant is studied. A stability analysis based on the Routh-Hurwitz criterion is carried out and a practical criterion for tuning the gains of the PI controller is proposed. Conclusions about the head pond and surge tank areas are drawn from the stability analysis. Finally, this criterion is applied to a real hydropower plant in design state; the importance of considering the spillway dimensions and turbine characteristic curves for adequate tuning of the controller gains is highlighted

Metodología de Diseño y Análisis de Sistemas Teleoperados Considerando Dinámica No Lineal

Cuando la separación física entre el sistema local y remoto es relativamente corta, el retardo no es perceptible; sin embargo, cuando el manipulador local y el manipulador remoto se encuentran a una distancia lejana uno del otro, el retardo de tiempo ya no es insignificante e influye negativamente en la realización de la tarea. El retardo de tiempo en un sistema de control introduce un atraso de fase que a su vez degrada el rendimiento del sistema y puede causar inestabilidad. Los sistemas de teleoperación pueden sacar provecho de la posibilidad de estar presente en dos lugares simultáneamente, sin embargo, el uso de Internet y otras redes de conmutación de paquetes, tales como Internet2, impone retardos de tiempo variables, haciendo que los esquemas de control ya establecidos elaboren soluciones para hacer frente a inestabilidades causadas por estos retardos de tiempo variables. En este trabajo de tesis se presenta el modelado y análisis de un sistema de teloperación bilateral no lineal de n grados de libertad controlado por convergencia de estado. La comunicación entre el sitio local y remoto se realiza mediante un canal de comunicación con retardo de tiempo. El análisis presentado en este trabajo considera que el retardo puede ser constante o variable. Los principales objetivos de este trabajo son; 1) Desarrollar una arquitectura de control no lineal garantizando la estabilidad del sistema teleoperado, 2) Evaluar la estabilidad del sistema considerando el retardo en la comunicación, y 3) Implementación de los algoritmos desarrollados para probar el desempeño de los mismos en un sistema experimental de 3 grados de libertad. A través de la teoría de Estabilidad de Lyapunov y el funcional Lyapunov-Krasovskii, se demuestra que el sistema de lazo cerrado es asintóticamente estable. Estas conclusiones de estabilidad se han obtenido mediante la integración de la función de Lyapunov y aplicando el Lema de Barbalat. Se demuestra también que se logra sincronizar las posiciones del manipulador local y remoto cuando el operador humano no mueve el manipulador local y el manipulador remoto se mueve libremente. El esquema de control propuesto se ha validado mediante simulación y en forma experimental empleando un sistema de teleoperación real desarrollado en esta tesis doctoral y que consta de un un manipulador serie planar de tres grados de libertad, un manipulador local, PHANTOM Omni, el cual es un dispositivo haptico fabricado que consta de 3 grados de libertad (en fuerza) y que proporciona realimentación de fuerza en los ejes x,y,z. El control en tiempo real se ha diseñado usando el Sistema Operativo en Tiempo Real QuaRC de QUARC en el lado local y el Simulink Real-Time Windows TargetTM en el lado remoto. Para finalizar el resumen se destaca el impacto de esta tesis en el mundo científico a través de los resultados publicados: 2 artículos en revistas con índice de impacto , 1 artículo en una revista indexada en Sistemas, Cibernética e Informática, 7 artículos en congresos y ha obtenido un premio en la 9a. Conferencia Iberoamericana en Sistemas, Cibernética e Informática, 2010. ABSTRACT When the physical separation between the local and remote system is relatively short, the delay is not noticeable; however, when the local manipulator and the remote manipulator are at a far distance from each other, the time delay is no longer negligible and negatively influences the performance of the task. The time delay in a control system introduces a phase delay which in turn degrades the system performance and cause instability. Teleoperation systems can benefit from the ability to be in two places simultaneously, however, the use of Internet and other packet switched networks, such as Internet2, imposes varying time delays, making established control schemes to develop solutions to address these instabilities caused by different time delays. In this thesis work we present a modeling and analysis of a nonlinear bilateral teloperation system of n degrees of freedom controlled by state convergence strategy. Communication between the local and remote site is via a communication channel with time delay. The analysis presented in this work considers that the time-delay can be constant or variable. The main objectives of this work are; 1) Develop a nonlinear control schemes to ensure the stability of the teleoperated system, 2) Evaluate the system stability considering the delay in communication, and 3) Implementation of algorithms developed to test the performance of the teleoperation system in an experimental system of 3 degrees of freedom. Through the Theory of Stability of Lyapunov and the functional Lyapunov-Krasovskii, one demonstrates that the closed loop system is asymptotically stable.. The conclusions about stability were obtained by integration of the Lyapunov function and applying Barbalat Lemma. It further shows that the positions of the local and remote manipulator are synchronize when the human operator stops applying a constant force and the remote manipulator does not interact with the environment. The proposed control scheme has been validated by means of simulation and in experimental form using a developed system of real teleoperation in this doctoral thesis, which consists of a series planar manipulator of three degrees of freedom, a local manipulator, PHANTOM Omni, which is an haptic device that consists of 3 degrees of freedom (in force) and that provide feeback force in x-axis, and, z. The control in real time has been designed using the Operating system in Real time QuaRC of Quanser in the local side and the Simulink Real-Time Windows Target in the remote side. In order to finalize the summary, the highlights impact of this thesis in the scientific world are shows through the published results: 2 articles in Journals with impact factor, one article in a indexed Journal on Systemics, Cybernetics and Informatics, 7 articles in Conferences and has won an award in 9a. Conferencia Iberoamericana en Sistemas, Cibernética e Informática, 2010.