The influence of cervical finish line, internal relief, and cement type on the cervical adaptation of metal crowns

Objective: the aim of this investigation was to evaluate the cervical adaptation of metal crowns under several conditions, namely (1) variations in the cervical finish line of the preparation, (2) application of internal relief inside the crowns, and (3) cementation using different luting materials. Method and Materials: One hundred eighty stainless-steel master dies were prepared simulating full crown preparations: 60 in chamfer (CH), 60 in 135-degree shoulder (OB), and 60 in rounded shoulder (OR). The finish lines were machined at approximate dimensions of a molar tooth preparation (height: 5.5 mm; cervical diameter: 8 mm; occlusal diameter: 6.4 mm; taper degree: 6; and cervical finish line width: 0.8 mm). One hundred eighty corresponding copings with the same finish lines were fabricated. A 30-mu m internal relief was machined 0.5 mm above the cervical finish line in 90 of these copings. The fit of the die and the coping was measured from all specimens (L0) prior to cementation using an optical microscope. After manipulation of the 3 types of cements (zinc phosphate, glass-ionomer, and resin cement), the coping was luted on the corresponding standard master die under 5-kgf loading for 4 minutes. Vertical discrepancy was again measured (L1), and the difference between L1 and L0 indicated the cervical adaptation. Results: Significant influence of the finish line, cement type, and internal relief was observed on the cervical adaptation (P < .001). The CH type of cervical finish line resulted in the best cervical adaptation of the metal crowns regardless of the cement type either with or without internal relief (36.6 +/- 3 to 100.8 +/- 4 mu m) (3-way analysis of variance and Tukey's test, alpha = .05). The use of glass-ionomer cement resulted in the least cervical discrepancy (36.6 +/- 3 to 115 +/- 4 mu m) than those of other cements (45.2 +/- 4 to 130.3 +/- 2 mu m) in all conditions. Conclusion: the best cervical adaptation was achieved with the chamfer type of finish line. The internal relief improved the marginal adaptation significantly, and the glass-ionomer cement led to the best cervical adaptation, followed by zinc phosphate and resin cement.

Influence of heat treatment on the optical properties of SnO2 : Sb thin films deposited by dip coating using aqueous solution

Antimony doped tin oxide thin films were deposited on glass by a chemical route derived from Pechini method. Particular emphasis was given to the microstructure of crystallized films. Crystalline phase formation was studied by grazing incident X-ray diffraction and by thermal analyses. Scanning electron microscopy was carried out for microstructure characterization, surface roughness was observed using scanning tunneling microscope and the optical transmittance measurements were performed in the wavelength range of 200-800 nm. (C) 2002 Kluwer Academic Publishers.

Influence of temperature on the microstructure and electrical properties of BBT thin films

The BBT films were prepared by a spin-coating process from the polymeric precursor method (Pechini process). In order to study the influence of the temperature on the BBT microstructure and electrical properties, the films were deposited on platinum coated silicon substrates and annealed from 700degreesC to 800degreesC for 2 hours in oxygen atmosphere. The crystallinity of the films was examined by X-ray diffraction while the surface morphology was analysed by atomic force microscope. The dielectric properties and dissipation factor of BaBi2Ta2O9 films at 1 MHz were observed. The polarization-electric field hysteresis loops revealed the ferroelectric characteristics of BaBi2Ta2O9 thin films.

Ferroelectric properties and leakage current characteristics of Bi3.25La0.75Ti3O12 thin films prepared by the polymeric precursor method

The ferroelectric properties and leakage current mechanisms of preferred oriented Bi3.25La0.75Ti3O12 (BLT) thin films deposited on La0.5Sr0.5CoO3 by the polymeric precursor method were investigated. These films showed excellent ferroelectric properties in terms of large remnant polarization (2P(r)) of 47.6 mu C/cm(2) and (2E(c)) of 55 kV/cm, fatigue-free characteristics up to 10(10) switching cycles, and a current density of 0.7 mu A/cm(2) at 10 kV/cm. X-ray diffraction and scanning electron microscope investigations indicate that the deposited films exhibit a dense, well-crystallized microstructure having random orientations and with a rather smooth surface morphology. The improved ferroelectric and leakage current characteristics can be ascribed to the platelike grains of the BLT films, which make the domain walls easier to be switched under external field.

Kinetics of zinc uptake and anatomy of roots and leaves of coffee trees as affected by zinc nutrition

Zinc (Zn) uptake kinetics and root and leaf anatomy were studied in coffee trees grown in nutrient solutions with or without Zn. Leaves and roots were sampled and cuts were made in the medium part of the leaves and in root tips and observed under an optical microscope. Plants grown without Zn showed an increase in root and in root stele diameter. There was also an increase in epidermis thickness and in the cross-sectional area of the cortex and stele due to Zn deficiency, but the diameter of xylem vessels was decreased. An increase in root cortex and stele diameter provided for an increased surface for nutrient uptake. Accordingly, C(min) was decreased from 13.8 to 3.4 mu mol L(-1) and V(max) increased from 0.50 to 2.1 mu mol cm(-2) h(-1) .

Some structural and physicochemical characteristics of tuber and root starches

Starches from six different species (cassava, arrowroot, sweet potato, yam, canna and ginger) were isolated and some structural and physicochemical characteristics analysed and correlated. Phosphorous and amylose contents were determined using a colorimetric method and measuring iodine affinity, respectively. Molecular weight distributions of starches were analysed by Sepharose CL 2B. Granular shape and size distribution were performed using an image analyser system attached to a light microscope. Swelling power was determined at 60, 70, 80 and 90 degrees C. Pasting and thermal properties were measured using a rapid viscoanalyser, and a differential scanning calorimeter, respectively. Phosphorous content varied from 0.007 to 0.031% for cassava and canna starches, respectively. Yam, canna and ginger starches displayed higher amylose contents (32.6, 31.7 and 26.5%, respectively) than cassava, arrowroot and sweet potato starches (19.8, 20.8 and 22.6%, respectively). These last three starches displayed amylose molecules of higher molecular weight than those shown for yam, canna and ginger starches. Canna starch showed higher proportions of longer branch chains of amylopectin than others starches. The size and shape of granules were quite variable among all starches and the average size of granules varied from 13.9 to 42.3 mu m for sweet potato and canna, respectively. Swelling power, pasting, and thermal properties were affected by structural characteristics of the starches.

Ontogenic development of Guazuma ulmifolia (Sterculiaceae) sapplings

Guazuma ulmifolia is as popular reforestation tree all over Latin America. It is characteristic of the initial stages of the secondary sucession and presents potential utility in the restoring of degraded areas. There is no information about fruit,seed and seedling morphology, which is of fundamental importance for identification, extraction, management and seed germination as well as for the characterization of post-seminal development and normal seedling pattern. To obtain such information, external fruit, and external and internal seed structures were studied considering shape, size, micropile and embryo localization; and tegumentar structures. All stages of this work were conduced in the Universidade Estadual Paulista (UNESP), Campus of Jaboticabal city. The fruits were collected in a mixed plantation in Jaboticabal city, State of São Paulo, Brazil. For the bio metric study eight repetitions of ten fruits and eight repetitions of 100 seeds were utilized. For seed internal traits study, 50 seeds were drenched in a distiled water, cut, and observed with a scanning electron microscope and a stereomicroscope, For post-seminal study ten repetitions of seven seeds were scarificated chemically with sulphuric acid during 50 min, and placed to germinate ina culture medium, at 30 degrees C, and eight hours of photoperiod. We found elipsoid, woody, indehiscent, pentacarpelar fruits, with a mean lenght of 22.61 mm (diameter 24.88 mm) and 64.0 seeds per fruit. Seed shape varies, mean length is 3.07 mm (width of 2.36 mm). The seed is bitegumented, tegmic, with a continuous, axial and curved embryo. The germination is epigeal and the seedlings are fanerocotiledoneus. Drawings of all stages are included.

Effect of bleaching on the cemento-enamel junction

Purpose: To evaluate the effect of various bleaching agents on the cemento-enamel junction (CEJ) of human teeth by scanning electron microscopy (SEM) analysis. Methods: 30 intact teeth were selected and longitudinally sectioned, yielding 60 specimens. Thirty specimens served as controls; the other 30 were divided into six groups with five specimens each (n= 5) and bleached according to six protocols (Group 1: External bleaching with 10% carbamide peroxide; Group 2: External bleaching with 35% hydrogen peroxide; Group 3: External bleaching with 35% hydrogen peroxide; Group 4: Internal/external bleaching with 35% hydrogen peroxide; Group 5: Internal/external bleaching with 35% hydrogen peroxide; and Group 6: Intracoronal bleaching with a paste of sodium perborate mixed with 9% hydrogen peroxide). After treatment the specimens were prepared and examined in a scanning electron microscope. Results: the bleaching agents used in this study caused morphological changes in the CEJ and increased dentin exposure.

Ultrastructure and histochemistry of the mineral concretions in the midgut of bees (Hymenoptera: Apidae)

Mineral concretions in the digestive cells of bees were examined under transmission electron microscope and histochemically. Ultrastructure shows two types of mineral deposits: 1) mineral concretions which are organized in granules with a striking concentrically layered organization of opaque and clear zones and 2) electron dense granules which appear inside small vacuoles (0.4-0.7 mu m). These two structures are present in the apex of the digestive cells of the posterior midgut. Histochemical data reveal that mineral concretions are composed of calcium, iron and uric acid or its salts while calcium determination gives a positive reaction for electron dense granules. Morphological and chemical similarities between the mineral concretions of bees and those described for other insects suggest that they have an important physiological role regulating the composition of the internal environment and to avoid intoxication. Since concretions and granules are structurally distinct, it is suggested that they are functionally different.

Boron deficiency inhibits petiole and peduncle cell development and reduces growth of cotton

The effect of boron (B) on cotton growth and fruit shedding may be due not only to physiological or biochemical effects, but also to vascular tissue malformation. This experiment investigated petiole and floral peduncle anatomical alterations and growth of cotton supplied with deficient and sufficient B in nutrient solution. Cotton (Gossypium hirsutum cv. 'Delta Opal') plants were grown in solutions containing 0, 1.5, 3.0, 4.5, and 6.0 mu mol L-1 of B from 22 to 36 d after plant emergence (DAPE). From 36 to 51 DAPE, B was omitted from the nutrient solution. Petioles from young leaves and floral bud peduncles (first position of the first sympodial) were sampled and the cross-section anatomy observed under an optical microscope. The number of vascular bundles of the petiole was decreased in B-deficient plants and the xylem was disorganized. Phloem elements in the peduncle vascular cylinder of B-deficient plants did not show clear differentiation. The few xylem elements that were formed were also disorganized. Modifications caused by B deficiency may have impaired B and photosynthate translocation into new cotton growth. Boron accumulation in the shoot of B-deficient plants suggested that there was some B translocation within the plant. It could be inferred that cotton growth would be impaired by the decrease in carbohydrate translocation rather than by B deficiency in the tissue alone.

Preparation of Fe-Cr-P-Co amorphous alloys by electrodeposition

The effects of bath composition and electroplating conditions on structure, morphology, and composition of amorphous Fe-Cr-P-Co deposits on AISI 1020 steel substrate, priorly plated with a thin Cu deposit, were investigated. The increase of charge density activates the inclusion of Cr in the deposit. However, above specific values of the charge density, which depend on the deposition current density, the Cr content in the deposit decreases. This Cr content decreasing is probably due to the significant hydrogen evolution with the increasing of deposition cur-rent and charge density. The effect of charge density on the content of Fe and Co is not clear. However, there is a tendency of increasing of Fe content and decreasing of Co content with the raising of current density. The Co is more easily deposited than the P, and its presence results in a more intense inhibition effect on the Cr deposition than the inhibition effect caused by P presence. Scanning electron microscope (SEM) analysis showed that Co increasing in the Fe-Cr-P-Co alloys analyzed does not promote the susceptibility to microcracks, which led to a good quality deposit. The passive film of the Fe-Cr-P-Co alloy shows a high ability formation and high protective capacity, and the results obtained by current density of corrosion, j(cor), show that the deposit with addition of Co, Fe31Cr11P28Co30, presents a higher corrosion resistance than the deposit with addition of Ni, Fe54Cr21P20Ni5. (C) 2004 Published by Elsevier B.V.

Growth and juvenile development of Uca maracoani Latreille 1802-1803 in laboratory conditions (Crustacea, Decapoda, Brachyura, Ocypodidae).

The life cycle of decapod crustaceans can be classified into three distinct morphological phases: larval, juvenile and adult. Despite its recognized importance, studies of the juvenile phase have been neglected. The present Study aimed to analyze the growth of juveniles from a single population of Uca maracoani under laboratory conditions, and also to describe the morphological differentiation of pleopods in each sex. Megalopae and juvenile crabs or U. maracoani obtained on a Mud beach at Jabaquara, Paraty, on the southern coast of the state of Rio de Janeiro (Brazil), were reared in the laboratory. The specimens were checked daily for molts and deaths. The carapace widths (CW) of intact exuviae and dead individuals were measured under a stereoscopic microscope provided with a micrometer rule. These data allowed the definition of a growth equation as well as the stages related to the beginning of pleopod development, which begins when females reach 3.0 mill CW (6th juvenile developmental stage), similar to the sizes reported for other species of the genus. In males, however, pleopods appear when the crabs reach 3.5 mm CW, equivalent to the 7th developmental stage. This difference may be related to differential growth between sexes. It also may be a consequence of laboratory rearing, or may represent an actual feature of the species.

Modification of surface properties of Ti-16Si-4B powder alloy by plasma immersion ion implantation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Potencial alelopático e levantamento do banco natural de sementes sob a copa de Copaifera langsdorffii Desf

the aim of this study was to evaluate the allelopathic effect of soil samples collected under the canopies of three specimens of Copaifera langsdorffii the germination of Lactuca sativa and survey the natural seed bank according to seasonality. To test the allelopathic effect was carried experiments of pre and post-emergence with seeds of L. sativa and to quantify the stock of seeds, soil samples were collected from three specimens at three distances from the stem (1, 2 and 3 m) and at three depths (0-5, 5-10 and 10-15cm) in the region of savanna in the dry and wet seasons. The samples tested in bioassay of pre-emergence no significant influence on germinability, mean germination time and mean germination speed, but showed a difference in the synchronism of germination, these data were independent of sampling station. In test for post-emergence was observed statistical difference in the parameters evaluate (length of primary roots and hypocotyls) in both seasons. To quantify the natural seed bank were macroscopic analysis of each soil sample with the help of stereoscopic microscope. The analysis of the natural seed bank showed a larger number of seeds in the 0-5cm and in distance of 2m for both seasons. The results suggest the presence of allelochemical substances in soil samples collected under the canopy of Copaifera langsdorffii.

An In Vitro Comparison of Different Cementation Strategies on the Pull-out Strength of a Glass Fiber Post

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)