Antioxidant activity of Agaricus blazei

The ethanolic extract of Agaricus blazei and ethyl acetate and hydroalcoholic fractions were evaluated for their antioxidant activity. (C) 2007 Elsevier B.V. All rights reserved.

Praziquantel-loaded PLGA nanoparticles: preparation and characterization

Nanoparticles containing praziquantel made of Poly (D,L-lactide-co-glycolide) were designed by an emulsion-solvent evaporation method. Two organic solvents were separately utilized as disperse phase: methylene chloride and ethyl acetate. The size of the particles prepared with the former solvent was bigger than the particles prepared with the latter. The entrapment efficiency was bigger when methylene chloride was used, 79.82% in comparison with 29.27% by using ethyl acetate. DSC and infrared studies showed that no strong chemical interaction between drug and polymer occurred. Release kinetics of praziquantel, used as a model drug, was governed not only by actual drug loading but also by particles size. The higher the drug content and the smaller the particle size resulted in faster drug release.

Influence of extracts of Stryphnodendron polyphyllum Mart. and Stryphnodendron obovatum Benth. on the cicatrisation of cutaneous wounds in rats

Stem bark of the two species Stryphnodendron polyphyllum Mart. and Stryphnodendron obovatum Benth., Leguminosae, was investigated for wound healing, antibacterial and antioxidant activity. These plants contain 12 and 19% tannins in their stem bark, respectively, and are widely used in traditional medicine in Brazil. The total content of phenolics of the crude extract (CE) of Stryphnodendron obovatum was 76.95 +/- 2.98% (CV = 3.87%) and of the ethyl-acetate fraction (EAF) was 89.13 +/- 0.34% (CV = 0.38%); whereas in Stryphnodendron polyphyllum the CE phenolics content was 51.62 +/- 1.53% (CV = 2.96%) and the EAF phenolics content was 59.00 +/- 1.91% (CV = 3.24%). The tannin content of CE from Stryphnodendron obovatum [36.58 +/- 0.35% (CV = 0.98%)] was about 11% higher than in CE from Stryphnodendron polyphyllum [25.43 +/- 0.96% (CV = 3.77%)]. The difference between the species was even greater in the EAF: in Stryphnodendron obovatum the EAF phenolics content was 55.01 +/- 0.36% (CV = 0.65%), whereas in Stryphnodendron polyphyllum the content was 36.16 +/- 0.42% (CV = 1.16%). The healing effect of ointments containing 2.5% crude lyophilised extract (PCE) and 2.5% ethyl-acetate lyophilised fraction (PEA) of the stem bark of Stryphnodendron polyphyllum and Stryphnodendron obovatum was studied in cutaneous wounds of Wistar((R)) rats after 4, 7 and 10 days of treatment. Epithelial cell proliferation in the area of re-epithelialisation of the wounds was evaluated by counting the metaphases blocked by vincristine sulfate. With PCE an increase in epidermal growth was observed after 4 and 7 days of treatment with Stryphnodendron polyphyllum, and after 7 and 10 days of treatment with Stryphnodendron obovatum. Wounds treated with PEA of Stryphnodendron obovatum showed increased epidermal growth only 4 days after the treatment, for Stryphnodendron polyphyllum, epidermal growth was observed after 4 and 7 days of treatment. Both the CE and the EAF fractions of Stryphnodendron polyphyllum and Stryphnodendron obovatum showed antibacterial activity against Staphylococcus aureus with MIC values of 125 and 250 mu g/ml, respectively. Gram-negative bacteria tested were not inhibited by extracts and fractions at concentrations > 1000 mu g/ml. The antioxidant activity through reduction of the DPPH radical in TLC, confirmed the anti-radical properties of these extracts in both species. CE and EAF of both species showed a radical scavenging activity (RSA) and protected DPPH from discolouration, already at 0.032 mu g/ml. The extract from Stryphnodendron polyphyllum were more effective than those Stryphnodendron obovatum, although the former had a lower tannin content. (c) 2005 Elsevier B.V.. All rights reserved.

Antiviral effect of Guazuma ulmifolia and Stryphnodendron adstringens on poliovirus and bovine herpesvirus

Crude extract (CE) and aqueous (AqF) and ethyl acetate (EtOAcF) fractions of Guazuma ulmifolia LAM., Sterculiaceae and the corresponding AqF, EtOAcF of Stryphnodendron adstringens (MART.) COVILLE, Leguminosae were tested for their antiviral activity against poliovirus 1 (P-1) and bovine herpesvirus 1 (BHV-1) in HEp2 cultured cells. The antiviral activity was monitored by plaque assay and immunolluorescence assay (IFA) under virucidal and therapeutic protocols. The therapeutic protocol demonstrated statistically significant positive results with both plants and for both virus strains. The highest percentages of viral inhibition were found for G. ulmifolia EtOAcF which inhibited BHV-1 and P-1 replication by 100% and 99%, respectively (p < 0.05, Student's t-test). For S. adstringens, AqF was the most efficient, inhibiting BHV-1 and P-1 by 97% and 93%, respectively (p < 0.05). In the virucidal protocol, G. ulmifolia CE inhibited the replication of BHV-1 and P-1 by 60% and 26%, respectively (p < 0.05), while, for S. adstringens, inhibition of 62% (p < 0.05) was demonstrated only with EtOAcF for P-1. IFA demonstrated that the greatest reduction in fluorescent cell number occurred with G. ulmifolia, under the therapeutic protocol for both virus strains. However, AqF and EtOAcF of S. adstringens were most efficient with the virucidal protocol for P-1 In conclusion, we demonstrated that G. ulmifolia and S. adstringens inhibited BHV-1 and P-1 replication, as well as, blocked the synthesis of viral antigens in infected cell cultures.

Major carotenoid composition of Brazilian Valencia orange juice: Identification and quantification by HPLC

The carotenoid composition of Brazilian Valencia orange juice was determined by open column chromatography (OCC) and high-performance liquid chromatography. Carotenoid pigments were extracted using acetone and saponified using 10% methanolic potassium hydroxide. Sixteen pigments were isolated by OCC and identified as alpha-carotene, zeta-carotene, beta-carotene, alpha-cryptoxanthin, beta-cryptoxanthin, lutein-5,6-epoxide, violaxanthin, lutein, antheraxanthin, zeaxanthin, luteoxanthin A, luteoxanthin B, mutatoxanthin A, mutatoxanthin B, auroxanthin B and trollichrome B. Thirteen carotenoid pigments were separated using a ternary gradient (acetonitrile-methanol-ethyl acetate) elution on a C-18 reversed-phase column. Among these, violaxanthin, lutein, zeaxanthin, beta-cryptoxanthin, zeta-carotene, alpha-carotene, and beta-carotene were quantified. The total carotenoid content was 12 +/- 6.7 mg/1, and the major carotenoids were lutein (23%), beta-cryptoxanthin (21%), and zeaxanthin (20%). 2005 Elsevier Ltd. All rights reserved.

Aroma volatiles recovered in the water phase of cashew apple (Anacardium occidentale L.) juice during concentration

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aspectos dinâmicos da água versus álcool e acetona por técnicas de congelamento

Water still represents, on its critical properties and phase transitions, a problem of current scientific interest, as a consequence of the countless open questions and of the inadequacy of the existent theoretical models, mainly related to the different solid and liquid phases that this substance possesses. For example, there are 13 known crystalline forms of water, and also amorphous phases. One of them, the amorphous ice of very high density (VHDA), was just recently observed. Other example is the anomalous behavior in the macroscopic density, which presents a maximum at the temperature of 277 K. In order to experimentally investigate the behavior of one of the liquid-solid phase transitions, the anomaly in its density and also the metastability, we used three different cooling techniques and, as comparison systems, we made use of the solvents: acetone and ethyl alcohol. The first studied cooling system employ a Peltier plate, a device recently developed, which makes use of small cubes made up of semiconductors to change heat among two surfaces; the second system is a commercial refrigerator, similar to the residential ones. Finally, the liquid nitrogen technique, which is used to refrigerate the samples in a container, in two ways: a very fast and other one, almost static. In those three systems, three Beckers of aluminum were used (with a volume of 80 ml, each), containing water, alcohol and acetone. They were closed and maintained at atmospheric pressure. Inside of each Becker were installed three thermocouples, disposed along the vertical axis of the Beckers, one close to the inferior surface, other to the medium level and the last one close the superior surface. A system of data acquisition was built via virtual instrumentation using as a central equipment a Data-Acquisition board. The temperature data were collected by the three thermocouples in the three Beckers, simultaneously, in function of freezing time. We will present the behavior of temperature versus freezing time for the three substances. The results show the characterization of the transitions of the liquid

Evaluation of anti-Mycobacterium tuberculosis activity of Campomanesia adamantium (Myrtaceae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On the origin of exciton formation in dye doped Alq(3) OLEDs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of ecological efficiency in internal combustion engines: The use of biodiesel

This paper evaluates and quantifies the environmental impact from the use of some renewable fuels and fossils fuels in internal combustion engines. The following fuels are evaluated: gasoline blended with anhydrous ethyl alcohol (anhydrous ethanol), conventional diesel fuel, biodiesel in pure form and blended with diesel fuel, and natural gas. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. The ecological efficiency concept depends on the environmental impact caused by CO(2), SO(2), NO(x) and particulate material (PM) emissions. The exhaust gases from internal combustion engines, in the case of the gasoline (blended with alcohol), biodiesel and biodiesel blended with conventional diesel, are the less polluting; on the other hand, the most polluting are those related to conventional diesel. They can cause serious problems to the environment because of their dangerous components for the human, animal and vegetable life. The resultant pollution of each one of the mentioned fuels are analyzed, considering separately CO(2), SO(2), NO(x) and particulate material (PM) emissions. As conclusion, it is possible to calculate an environmental factor that represents, qualitatively and quantitative, the emissions in internal combustion engines that are mostly used in urban transport. Biodiesel in pure form (B100) and blended with conventional diesel as fuel for engines pollute less than conventional diesel fuel. The ecological efficiency for pure biodiesel (B100) is 86.75%: for biodiesel blended with conventional diesel fuel (B20, 20% biodiesel and 80% diesel), it is 78.79%. Finally, the ecological efficiency for conventional diesel, when used in engines, is 77.34%; for gasoline, it is 82.52%, and for natural gas, it is 91.95%. All these figures considered a thermal efficiency of 30% for the internal combustion engine. Crown Copyright (C) 2008 Published by Elsevier Ltd. All rights reserved.

Biodiesel CO2 emissions: A comparison with the main fuels in the Brazilian market

The use of biodiesel is increasing as an attractive fuel due to the depleting fossil fuel resources and environmental degradation. This paper presents results of an investigation on the potentials of biodiesel as an alternative fuel and main substitute of diesel oil, comparing the CO2 emissions of the main fuels in the Brazilian market with those of biodiesel, in pure form or blended in different proportions with diesel oil (2%, 5%, and 20%, called B2, B5, and B20, respectively). The results of the study are shown in ton CO2 per m(3) and ton CO2 per year of fuel. The fuels were analyzed considering their chemical composition, stoichiometric combustion parameters and mean consumption for a single vehicle. The fuels studied were: gasoline, diesel oil, anhydrous ethyl alcohol (anhydrous ethanol), and biodiesel from used frying oil and from soybean oil. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. With data provided by the Brazilian Association of Automotive Vehicle Manufacturers (ANFAVEA) for the number of vehicles produced in Brazil, the emissions of CO2 for the national fleet in 2007 were obtained per type of fuel. With data provided by the Brazilian Department of Transit (DENATRAN) concerning the number of diesel vehicles in the last five years in Brazil, the total CO2 emissions and the percentage that they would decrease in the case of use of pure biodiesel, B100, or several mixtures, B2, B5 and B20, were calculated. Estimates of CO2 emissions for a future scenario considering the mixtures B5 and B20 are also included in this article. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Síntese e caracterização de látices acrílicos reticulados com (1,6-diacrilato propoxilato hexanodiol) via polimerização em emulsão

Latices based on acrylic acid and ethyl methacrylate, crosslinked with 1,6‐propoxylate‐hexanodiol diacrylate were synthesized via emulsion polymerization with different monomeric compositions. The resultant latices were thickened with different NaOH/(acrylic acid) molar ratios and were characterized by titrimetry, zeta potential measurements, turbidimetry, and capillary viscometry. Intrinsic viscosity was determined for an uncrosslinked copolymer, using toluene as solvent. All the latices were coagulated with NaCl and washed with water at 60°C analyzed by FTIR spectrophotometry, in order to characterize functional groups from the copolymer and crosslinking agent.

Caracterização de látices acrílicos em função da neutralização de seus grupos carboxilas

Latexes based on acrylic acid, acrylamide, ethyl methacrylate, and ethyl acrylate were synthesized via emulsion polymerization with different monomer compositions. The resultant latices were thickened with different molar ratios of NaOH to acrylic acid and were analyzed in terms of acid‐basis titrimetry, turbidimetry, rheology, and tensiometry. Titrimetry, turbidimetry, and rheometry were used to analyze factors such as carboxyl group availability and particle solubilization, tensiometry monitoring the influence of carboxyl neutralization on polymer‐surfactant interactions. For the acrylic acid content used in this work (20 wt%), the results indicated that as carboxyl groups distribution became more homogeneous, the process of latex thickening became more effective

Obtenção e aplicação de sistemas microemulsionados na recuperação avançada de petróleo

Due to the need of increasing production in reservoirs that are going through production decline, methods of advanced recovery have frequently been used in the last years, as the use of conventional methods has not been successful in solving the problem of oil drifting. In this work, the efficiency of different microemulsionated systems in the flow of oil from cores from Assu and Botucatu formations. Regarding drifting tests, cores were calcinated at a temperature of 1000°C, for 18 hours, with the aim of eliminating any organic compound present in it, increasing the resultant permeability. Following, the cores were isolated with resin, resulting in test specimens with the following dimensions: 3.8 cm of diameter and 8.7 cm of length. Cores were saturated with brine, composed of aqueous 2 wt % KCl, and oil from Guamaré treatment station (Petrobras/RN). A pressure of 20 psi was used in all tests. After core saturation, brine was injected again, followed by oil at constant flow rate. The system S3 - surfactant (anionic surfactant of short chain), isoamillic alcohol, pine oil, and water - presented the best drift efficiency, 81.18%, while the system S1E commercial surfactant, ethyl alcohol, pine oil, and distilled water presented low drift efficiency, 44,68%

Desenvolvimento de componentes nanométricos para aplicação em células a combustível à base de sólidos estruturados e filmes finos

The present work aims the preparation of filmes of strontium-doped lanthanum manganite (perovskita) yttria-stabilized zirconia (LSM-SDC) films deposited on substrate of YSZ by means of spin coating technique having as principal objective their application to solid oxide fuel cells of intermediate temperature. La0,8Sr0,2MnO3 and Ce0,8Sm0,2O1,9 were obtained by modified Pechini method by use of gelatin which act as polymerization agent. The powders obtained were characterized by Xray fluorescence, X ray diffraction, electronic scanning microscopy and the superficial area by BET method. The results obtained by X-ray fluorescence showed that the route adopted for obtention of powders was effective in the obtention of the compositions with close values to the stoichiometrics. Ethyl cellulose was used as pore-forming agent and mixed with the LSM-SDC powders in weight proportions of 1:24, 2:23 and 1:9. The films were sintered at 1150 °C for 4 h and characterized by X-ray diffraction and scanning electron microscopy technique (SEM) and atomic force. The phases quantification of the precursory powders and of the obtained films was carried through Rietveld method. According with the analysis of SEM, as the content of ethyl cellulose was increased, the pore distribution in films become more uniform and the pore size reduced. The methodology used for the obtention of the films was very efficient, considering a material was obtained with characteristics that were proper to the application as electrolyte/cathode system to solid oxide fuel cells