Análise de desempenho de um fogão solar com parabola fabricada em material compósito

It is presented a solar cooker made with a parabolic reflector composed by a composite material. For this purpose, it was utilized a cast concrete with a parabolic profile obtained by means of modeling. It will be demonstrated the manufacturing process and settings, as well as tests results, in order to determine the contact temperature and cooking time of some foods. This solar cooker presents the following main characteristics: the concentration method, low cost and easy manufacturing process. It was performed by employing recycled materials such as cement, plaster, crushed polystyrene and wheels. The captation area measures 1 square meter and its parabole was covered with a mirrors measuring 25 cm2. A temperature higher than 650°C was obtained. Furthermore, it has been demonstrated that the cooking viability for several type of foods such as beans, potatoes, rice, yams and pasta can be used in two meals for a family of four. In addition, the advantages of this cooker were analysed in comparison with others described in literature as well as those operating on gas. Especially in Northeast of Brazil, where there is a potential for solar energy, this prototype is an important tool, because it avoids not only desertification, but also pollutants from burning firewoods which cause ecological imbalance

Análise de desempenho de um fogão solar construído a partir de sucatas de antena de tv

Given the growing environmental crisis caused by degradation, mainly due to the use of polluting energy sources, increasing the growing use of renewable energies worldwide, with emphasis on solar energy, an abundant supply and available to everyone, which can be harnessed in several ways: electricity generation; dehydration of food; heating, disinfection and distillation and cooking. The latter has as its primary feature the viability of clean, renewable energy for society, combating ecological damage caused by large-scale use of firewood for cooking foods, use in tropical countries with high solar radiation, and has funding NGOs throughout the world with the goal of achieving low-income population. The proposed project consists of a solar cooker for concentration, working from the reflection of sunlight by a hub that they converge to a focal point at the bottom of the pot, getting lots of heat. The solar cooker under study consists of two elliptical reflecting parabolas made from the recycling of scrap TV antenna, having 0.29 m² of surface area for each antenna, which were covered by multiple mirrors of 2 mm thick and mounted on a metal structure, with correction for the mobility of the apparent movement of the sun. This structure was built with the recycling of scrap metal, possessing a relatively low cost compared with other solar cookers, around US$ 50.00. This cost becomes negligible, since that will involve a great benefit to not have fuel costs for each meal, unlike the use of gas or firewood for cooking food. The tests show that the cooker has reached the maximum temperature of 740 ° C, for boiling water in an average time of 28 minutes, cooking various types of foods such as potatoes, rice and pasta in an average time of 45 minutes and still going as a solar oven, making pizza baking and meat. These cooking times do not differ much from the cooking times on a gas stove, it becomes the solar cooker as a good consumer acceptance, and furthermore not to deliver the same gases that can poison the food as with the wood stove. Proves the viability of using the stove to cook or bake in two daily meals for a family, still presenting a position to improve his performance with the addition of new materials, equipment and techniques

Compósito para fabricação de blocos para construção de casas: estudos térmico e de materiais

We present two models of blocks made of composite material obtained from the use of cement, plaster, EPS crushed, shredded tire, mud, sand and water, for the construction of popular housing. Were made metal molds for the manufacture of blocks to be used in the construction of a residence for low-income families. Performed tests of compressive strength of the composite for various formulations that met the specific standard for blocks used in construction. To study the thermal conductivity of the composite for further study of thermal comfort generated in a residence built with the proposed composite. We also determined the mass-specific and water absorption for each formulation studied. Using a home already built with another composite material, made up the closing of a window with the building blocks and found the thermal insulation, measuring external and internal temperatures of the blocks. The blocks had made good thermal insulation of the environment, resulting in differences of up to 12.6°C between the outer and inner faces. It will be shown the feasibility of using composite for the end proposed and chosen the most appropriate wording

Estudo de um compósito de matriz cerâmica com carga de recicláveis para o uso na construção civi

With a view to revitalizing public environments through criteria that include economy, tourism, aesthetics and respect for the environment, this paper proposes a model of kiosk manufactured with composite material blocks, to be employed as a public instrument. . The model consists of a structure composed of planned blocks and manufactured in cement-based composite, gypsum, ground and water, having the styrofoam inside filled with pet bottles of 500 ml dose. The social and environmental issue is the critical point of the work when it can, through the reuse of environmentally harmful materials such as polyethylene terephthalate PET, using such modules for the construction of various areas of Commerce, promoting the protection of the environment combined with the improvement of the quality of life of the population. The tourism factor, which is significant in the economy of the North, is also considered as the modulated kiosk has a visual aspect innovative and differentiated. The environmental issue is addressed by encouraging the reuse of PET material and EPS (polystyrene)

Resposta térmica de um compósito PEEK+PTFE+Fibra de carbono+grafite

Composites based on PEEK + PTFE + CARBON FIBER + Graphite (G_CFRP) has increased application in the top industries, as Aerospace, Aeronautical, Petroleum, Biomedical, Mechanical and Electronics Engineering challenges. A commercially available G_CFRP was warmed up to three different levels of thermal energy to identify the main damage mechanisms and some evidences for their intrinsic transitions. An experimental test rig for systematize a heat flux was developed in this dissertation, based on the Joule Effect. It was built using an isothermal container, an internal heat source and a real-time measurement system for test a sample by time. A standard conical-cylindrical tip was inserted into a soldering iron, commercially available and identified by three different levels of nominal electrical power, 40W (manufacturer A), 40W (manufacturer B), 100W and 150W, selected after screening tests: these power levels for the heat source, after one hour of heating and one hour of cooling in situ, carried out three different zones of degradation in the composite surface. The bench was instrumented with twelve thermocouples, a wattmeter and a video camera. The twelve specimens tested suffered different degradation mechanisms, analyzed by DSC (Differential Scanning Calorimetry) and TG (Thermogravimetry) techniques, Scanning Electron Microscopy (SEM) and Energy-Dispersive X-Rays (EDX) Analysis. Before and after each testing, it was measured the hardness of the sample by HRM (Hardness Rockwell M). Excellent correlations (R2=1) were obtained in the plots of the evaporated area after one hour of heating and one hour of cooling in situ versus (1) the respective power of heat source and (2) the central temperature of the sample. However, as resulting of the differential degradation of G_CFRP and their anisotropy, confirmed by their variable thermal properties, viscoelastic and plastic properties, there were both linear and non-linear behaviour between the temperature field and Rockwell M hardness measured in the radial and circumferential directions of the samples. Some morphological features of the damaged zones are presented and discussed, as, for example, the crazing and skeletonization mechanism of G_CFRP

Perfis de distribuição volumétrica de pontas XR 11003 e TXVK-4 em diferentes condições de pulverização

Com o objetivo de avaliar a uniformidade da distribuição volumétrica e o efeito da angulação dos bicos na barra em pulverizações, foi conduzido experimento em laboratório, com dez unidades de cada uma das pontas de jato plano XR 11003 e de jato cônico vazio TXVK-4, fabricadas pela Spraying Systems Co. As pontas XR 11003 foram avaliadas, isoladamente, em mesa de prova para bicos construída conforme a Norma ISO 5682-1:1996, a 0,30; 0,40 e 0,50 m de altura, submetidas à pressão de 200 e 300 kPa e posicionadas com ângulos de 30º e 45º no sentido horário e anti-horário e na vertical; as pontas TXVK-4 foram avaliadas nas mesmas alturas, porém a 300 e 400 kPa, e somente na vertical. A distribuição média do volume coletado em cada configuração, das dez unidades de cada ponta, foi inserida num programa computacional, desenvolvido para o estudo, que permitiu a simulação do padrão de deposição de uma barra pulverizadora, com 24 bicos, com sobreposições variáveis, obtendo-se, ao final, o coeficiente de variação da sobreposição, o desvio- padrão e a média do volume aplicado. Os resultados sugerem a necessidade de ajustes no espaçamento entre bicos para a obtenção de melhor uniformidade na distribuição, principalmente quando se utiliza ângulo na barra; há menor influência da variação da altura da barra sobre a uniformidade da distribuição quando o espaçamento entre bicos é reduzido.

Distribuição volumétrica de calda produzidas pelas pontas pulverização XR, TP e TJ sob diferentes condições operacionais

Foram avaliados os perfis de distribuição volumétrica das pontas de pulverização de jato plano Extended Range XR 8004, Teejet TP 8004 e TwinJet TJ60-8004, em mesa de teste construída segundo a norma ISO 5.682-1:1996, sendo as pontas de pulverização posicionadas a 30, 40 e 50 cm de altura da mesa coletora, submetidas à pressão de 200 e 300 kPa, e posicionadas com ângulos de 30 e 45º nos sentidos horário e anti-horário e na posição vertical (0º). As pontas TJ60-8004 foram analisadas nas mesmas alturas, porém somente na posição vertical. Avaliaram-se 10 unidades de cada tipo de ponta, instaladas isoladamente na mesa. A distribuição média do volume pulverizado, coletado nas provetas, foi inserida em programa computacional, que permitiu a simulação do perfil de distribuição de uma barra pulverizadora com 24 bicos, em espaçamentos variáveis, obtendo-se ao final o coeficiente de variação, o desvio-padrão e a média do volume. Os resultados mostraram que a uniformidade de distribuição é menos influenciada pela variação da altura da barra quando o espaçamento entre bicos é reduzido e que há necessidade de adequação do espaçamento quando se utiliza ângulo na barra pulverizadora.

Avaliação dos impactos ambientais gerados por uma industria cerâmica típica da Região do Seridó/RN

The present work deals with an evaluation of the environmental impacts arised from a typical ceramics industry located in the Seridó region of Rio Grande do Norte State. That region contains the largest State s producing basin of red ceramics. The district of Parelhas stands out as the largest producing nucleus. The studied company is located in the rural zone of Parelhas, it was selected as study object because it possesses a great part of the representative characteristics of the Region s ceramics park as a whole. Impacts produced at the implantation and operation phases of the Company had been evaluated, being this last phase subdivided in stages of the productive process. Among found adverse impacts, they are distinguished: losses in air quality, undesirable noises, microclimatic alterations, impoverishment of the ground, elimination of the vegetal covering, agricultural exodus, crisis in cattle agriculture and, superficial and underground water contamination, beyond risks ocupational diseases and industrial accidents. The Leopold s interactive matrix, that summarizes results of the work, was presented in form of 15 (fifteen) tables that display impacts classified in qualitative and quantitative way. Totally, 175 (one hundred and seventy-five) significant impacts produced by this Company had been identified, being 114 (one hundred and fourteen) negative, 38 (thirty-eight) positive and 23 (twenty-three) among mixed, indefinite and inert ones. In the work, before the evaluation of impacts properly said, it was constructed a diagnostic table of the ambient situation at a previous moment to implantation of the Company, elaborated on basis of inferences and historical researches. It was proposed still, mitigative steps for adverse impacts identified, as also elaborated a program to accompaniment and observing that the fulfilment of indicated mitigative steps guarantees. The final part of the work contemplates conclusions and suggestions that aim to influence positively the presented sight in terms of environmental management

Avaliação da capacidade de adsorção do CO2 em zeólita 12X com gases sintéticos e originados da pirólise do lodo de esgoto

This work depicts a study of the adsorption of carbon dioxide on zeolite 13X. The activities were divided into four stages: study batch adsorption capacity of the adsorbent with synthetic CO2 (4%), fixed bed dynamic evaluation with the commercial mixture of gases (4% CO2, 1.11% CO, 1 2% H2, 0.233% CH4, 0.1% C3, 0.0233% C4 argon as inert closing balance), fixed bed dynamic modeling and evaluation of the breakthrough curve of CO2 originated from the pyrolysis of sewage sludge. The sewage sludge and the adsorbent were characterized by analysis TG / DTA, SEM, XRF and BET. Adsorption studies were carried out under the following operating conditions: temperature 40 °C (for the pyrolysis of the sludge T = 600 °C), pressures of 0.55 to 5.05 bar (batch process), flow rate of the gaseous mixture between 50 - 72 ml/min and the adsorbent masses of 10, 15 and 20 g (fixed bed process). The time for the adsorption batch was 7 h and on the fixed bed was around 180 min. The results of this study showed that in batch adsorption process step with zeolite 13X is efficient and the mass of adsorbed CO2 increases with the increases pressure, decreases with temperature increases and rises due the increase of activation temperature adsorbent. In the batch process were evaluated the breakthrough curves, which were compared with adsorption isotherms represented by the models of Langmuir, Freündlich and Toth. All models well adjusted to the experimental points, but the Langmuir model was chosen in view of its use in the dynamic model does not have implications for adsorption (indeterminacy and larger number of parameters such as occurred with others) in solving the equation. In the fixed bed dynamic study with the synthetic gas mixture, 20 g of mass adsorbent showed the maximum adsorption percentage 46.7% at 40 °C temperature and 50 mL/min of flow rate. The model was satisfactorily fitted to the three breakthrough curves and the parameters were: axial dispersion coefficient (0.0165 dm2/min), effective diffusivity inside the particle (dm2/min 0.0884) and external transfer coefficient mass (0.45 dm/min). The breakthrough curve for CO2 in the process of pyrolysis of the sludge showed a fast saturation with traces of aerosols presents in the gas phase into the fixed bed under the reaction process

Recuperação e purificação de quitosanases usando adsorção em leito expandido com streamline DEAE com modelagem e simulação usando redes neurais

Expanded Bed Adsorption (EBA) is an integrative process that combines concepts of chromatography and fluidization of solids. The many parameters involved and their synergistic effects complicate the optimization of the process. Fortunately, some mathematical tools have been developed in order to guide the investigation of the EBA system. In this work the application of experimental design, phenomenological modeling and artificial neural networks (ANN) in understanding chitosanases adsorption on ion exchange resin Streamline® DEAE have been investigated. The strain Paenibacillus ehimensis NRRL B-23118 was used for chitosanase production. EBA experiments were carried out using a column of 2.6 cm inner diameter with 30.0 cm in height that was coupled to a peristaltic pump. At the bottom of the column there was a distributor of glass beads having a height of 3.0 cm. Assays for residence time distribution (RTD) revelead a high degree of mixing, however, the Richardson-Zaki coefficients showed that the column was on the threshold of stability. Isotherm models fitted the adsorption equilibrium data in the presence of lyotropic salts. The results of experiment design indicated that the ionic strength and superficial velocity are important to the recovery and purity of chitosanases. The molecular mass of the two chitosanases were approximately 23 kDa and 52 kDa as estimated by SDS-PAGE. The phenomenological modeling was aimed to describe the operations in batch and column chromatography. The simulations were performed in Microsoft Visual Studio. The kinetic rate constant model set to kinetic curves efficiently under conditions of initial enzyme activity 0.232, 0.142 e 0.079 UA/mL. The simulated breakthrough curves showed some differences with experimental data, especially regarding the slope. Sensitivity tests of the model on the surface velocity, axial dispersion and initial concentration showed agreement with the literature. The neural network was constructed in MATLAB and Neural Network Toolbox. The cross-validation was used to improve the ability of generalization. The parameters of ANN were improved to obtain the settings 6-6 (enzyme activity) and 9-6 (total protein), as well as tansig transfer function and Levenberg-Marquardt training algorithm. The neural Carlos Eduardo de Araújo Padilha dezembro/2013 9 networks simulations, including all the steps of cycle, showed good agreement with experimental data, with a correlation coefficient of approximately 0.974. The effects of input variables on profiles of the stages of loading, washing and elution were consistent with the literature

O papel das subsidiárias e a internacionalização das atividades tecnológicas pelas Empresas Transnacionais (ETNs)

Este estudo se propõe a analisar os mandatos das subsidiárias de empresas transnacionais (ETNs) no estrangeiro por intermédio dos mecanismos de alocação das atividades de pesquisa e desenvolvimento (P&D) entre os centros descentralizados de pesquisa. Iniciamos o trabalho com a apresentação de uma síntese das diferentes perspectivas encontradas na literatura econômica sobre a subordinação (ou condicionamentos) da autonomia administrativa e tecnológica das filiais. Tal síntese permite estabelecer uma hierarquia entre as subsidiárias e uma tipologia para evolução (retrocesso) de mandatos construída, principalmente, para as ETNs estruturadas em forma de rede corporativa. A seguir, a partir de pesquisas realizadas sobre as atividades dos laboratórios de P&D da indústria de equipamentos de telecomunicações no Brasil, procuramos mostrar que: a) a descentralização das atividades tecnológicas é um fato que não está restrito apenas aos países centrais; b) as tecnologias de informação permitiram que as subsidiárias no país se integrassem aos laboratórios centrais das ETNs, dando-lhes condições de desenvolver e participar de outras atividades tecnológicas, além das tradicionais funções de adaptação de processo e de produtos.

Mapeamento geoambiental do campo de dunas Pirangi-Potengi com ênfase a San Vale e Lagoinha Natal/RN: um instrumento de apoio ao planejamento ambiental

The city of Natal-RN is constructed on dune areas with wavy relives softly waved and green areas that help to keep a pleasant climate, amongst these is distinguished field Pirangi-Potengi the dune with the areas of San Vale and Lagoinha. These environments are being substituted gradual for property and other workmanships of engineering on behalf of the urban expansion. This study the elaboration of a geoambiental mapping of Field had as objective generality Pirangi-Potengi the Dune with emphasis the San Vale and Lagoinha in Natal-RN. The done mapping had as objective specific to elaborate a vegetation map, a map of registers in cadastre of ambient problems to dunes, a map of flooding susceptibility, a map of vulnerability to the underground water contamination and a map of use and occupation of the ground. Of the carried through analysis, the area in study reveals sufficiently degraded, remaining only few green areas and dunares, as well as, the vulnerable presence of areas of vulnerability in floods and areas the contamination of the water-bearing one. The gotten results allow to affirm that this type of mapping, is of great importance for analysis and evaluation of the environment of the city

Avaliação da eficiência de lagoas de estabilização no tratamento de resíduos esgotados de fossas sépticas

Because of disability in public policy development in mind to attend issues of sanitation in the municipalities, companies known as "clean-blue" appeared proposing to solve a simple collection and management of wastewater produced in single or multifamily residences, commercial, hospitals, etc. In the case of an activity in which there are no worries about the fate of sewage, emerged some doubts about the degree of health and environmental safety in these companies. Traditionally, most of them makes the provision of waste depleted soil or wetland, open, usually located on the outskirts of cities (MENESES, 2001). In turn, the sludge from septic tanks exhausted, provided no technical criteria - in the soil, rivers and as an agricultural fertilizer put in risk the health of the population and environmental quality. This work was entered in the search network 5 of the Notice of the Research Program in Sanitation - PROSAB-5, aimed to study the theme 'Characterization and study of alternative ways of treating sludge from septic tanks in the city of Natal, RN', proposing to evaluate the performance of the use of stabilization ponds as a system to handle waste from septic tanks exhausted. A series of lakes studied belong to one of the largest clean-pit of Natal, consisting of two anaerobic ponds, one facultative and maturation, and a tank disinfection, the wastewater being released in the Potengi River. Samples were collected between the months of October 2007 to October 2008, at six points previously defined and judged as more appropriate to what is proposed study. The analysis results in field and laboratory showed the most significant removal of COD (88.93%), total suspended solids (94.87%), organic nitrogen (66.87%) and thermotolerant coliforms (99.88%). Some results have not reached the expected because the system under study had operating problems that have undermined the efficiency of the reactors

Espaço e subjetividade: estudo com ribeirinhos

Nesta pesquisa, investigamos as transformações vividas por uma comunidade afetada pela construção de uma usina hidrelétrica no rio Paraná. Utilizando procedimentos da etnografia, realizamos várias visitas à comunidade, reassentada numa vila planejada e construída para substituir a antiga vila que foi submersa. Estabelecemos contatos com os moradores mais antigos e produzimos, com eles, diálogos entabulados em situações diversas, como em visitas às próprias casas e rodas de conversa ocorridas nas calçadas. Nas falas dos ribeirinhos, a mudança do espaço é sentida como algo negativo, em todos os planos da vida. Ressentem-se da perda do rio, da pesca farta, da caça realizada nas matas, das terras férteis cultivadas nas barrancas, da socialidade e de toda produção de subjetividade que mantinham naquele lugar marcado pela proximidade com o rio e suas águas.

Obras complementares: um elo entre a leitura e os conteúdos matemáticos

The Federal Government through its Plans and Programs invests in various policies intended to achieve the main goal of the millennium, provide basic education for all. Among them, we highlight in this paper The National Textbook Program, with emphasis on Complementary Works. These works are presented through different genres, such as poems, poetry, short stories, parables, novels, literature, educational materials etc.. providing a range of possible teaching work. However, little is known about the levels of education of teachers as intended. Based on the discussions and studies in this direction, sparked concerns us in the process of teaching and learning in math classes. This made us pay attention to a possibility of study where reading could be included in this process. In this sense, the present study aims at investigating the potential of conceptual and didactic use of Complementary Works on developing the skills of reading and writing mathematics of the first three years of elementary school, and from there, propose a courseware with guidelines for use of these works by teachers of 1st to 3rd year of elementary school. For this, we outline the issues of reading and understanding of mathematical interests as those of our study. In this sense, the proposal was built from the bibliographic works that address the contributions of reading for learning mathematical content, like Machado (2001), Nacarato (2009); Dantas (2011), Smole and Diniz ( 2001). As a result, we created the Guidance for the use of Complementary Works for Teachers to Teach Mathematics with a view to support the practice of teachers and future teachers who teach mathematics. Supported the use of Complementary Works, especially those distributed in public schools by the National Textbook - PNLD and have mathematical content, this guide is intended to present some of the possible use of this feature in math classes. (Education Observatory - Capes / INEP. Ed. 038-2010. TELL Research Group - UFRN - PPGED / PPGEL / PPGECNM - PROPESQ)