On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

An experimental and theoretical study of multiphase flow in a circulating fluidized bed

A systematic averaging procedure has been derived in order to obtain an integral form of conservation equations for dispersed multiphase flow, especially applicable to fluidized beds. A similar averaging method is applied further to formulate macroscopic integral equations, which can be used in one-dimensional and macroscopic multi dimensional models. Circulating fluid bed hydrodynamics has been studied experimentally and both macroscopic and microscopic flow profiles have been measured in a cold model. As an application of the theory, the one dimensional model has been used to study mass and momentum conservation of gas and solid in a circulating fluid bed. Axial solid mixing has also been modelled by the one dimensional model and mixing parameters have been evaluated.

Percepción de las enfermeras de UCI en relación al cuidado satisfactorio: convergencias y divergencias con la percepción del paciente crítico

Objetivo: Explorar las convergencias y divergencias entre la percepción de las enfermeras y los pacientes críticos, en relación a los cuidados satisfactorios proporcionados y recibidos. Métodos: Forma parte de un estudio cualitativo más amplio, según la Teoría Fundamentada. Realizado en 3 Unidades de Cuidados Intensivos con 34 boxes. Muestreo teórico por perfiles con n = 19 pacientes y n = 7 enfermeras tras la saturación de datos. El reclutamiento de pacientes incluidos en los perfiles de edad avanzada y larga estancia se dilató en el tiempo por la baja incidencia de estos. La recogida de datos consistió en: entrevista en profundidad a los pacientes críticos, grupo de discusión de enfermeras expertas en el cuidado al paciente crítico y diario de campo. Análisis temático de Teoría Fundamentada según Strauss y Corbin: codificación abierta, axial y selectiva. Se siguieron los criterios de rigor de Guba y Lincoln, de calidad de Calderón y los de reflexividad ética de Gastaldo y McKeever. Se obtuvo informe favorable del comité de ética del centro y consentimiento informado de los participantes. Resultados: Emergen 4 categorías coincidentes: las competencias profesionales, los cuidados humanos, técnicos y continuados. La combinación de estos elementos producen sentimientos de seguridad, tranquilidad, sentirse persona permitiendo al paciente una relación cercana y de confianza con la enfermera que realiza cuidados individualizados. No se han encontrado categorías divergentes. Conclusiones: Las percepciones de las enfermeras en relación a los cuidados coinciden con las percepciones de los pacientes críticos tanto en la definición como en las dimensiones sobre el cuidado satisfactorio.

Polarizabilidades e primeira hiperpolarizabilidades elétricas dipolares de ésteres E-4-amino-trans-1,3-butadienil-(1',2'-di-hidroxibenzeno) de boro, alumínio e gálio

Static electric dipole polarizabilities and first hyperpolarizabilites have been calculated for the title molecules and their 3' and 4'-nitro derivatives at ab-initio Hartree- Fock/6-31G(d, p) level. The influence of the pivotal p vacant 3A elements (B, Al or Ga) substitution on the electrical properties of these molecules is detailed. The axial vector components of the first hyperpolarizabilities β(0) of the push-pull 4'-nitro derivatives, -18.2×10-32 esu (B), -21.1×10-32 esu (Al) and -20.8×10-32 esu (Ga) are calculated to be as much as fourfold larger then that calculated for the p-nitroaniline, a reference organic molecule for comparison for this type of molecular property.

Síntese e caracterização de complexos de platina(IV) com derivados N-benzilados da 1,3-propanodiamina

The present work describes the synthesis of a series of platinum(IV) complexes with N-benzyl 1,3-propanediamine derivatives. Since substitution of the axial ligands in the platinum(IV) complexes may alter their pharmacological properties, we have prepared complexes with different groups, such as hydroxide, chloride and acetate using a sequence of substitution reactions. The resulting complexes were fully characterized by IR, ¹H, 13C and 195Pt NMR spectroscopies, and elemental analysis.

Kestomagneettigeneraattorin staattorin mekaanisen rakenteen analysointi ja kehitys

Työssä tutkittiin kestomagneettigeneraattorin staattoriytimen aksiaalisen puristamisen ja lämpötilan vaikutuksia staattorin jännityksiin ja muodonmuutoksiin. Lisäksi tutkittiin aksiaalisen puristusjännityksen vaikutusta staattorin aksiaalisuuntaisen ominaismuodon taajuuteen. Rakenteesta tehtiin elementtimalli, jonka avulla laskettiin rakenteen siirtymät, jännitykset ja ominaistaajuudet. Rakenteen jännityksiä ja siirtymiä tutkittiin myös yksinkertaisella jousikuvauksella, jonka tuloksia verrattiin elementtimallilla saatuihin tuloksiin. Työn tavoitteena oli kehittää uusi staattorirakenne. Elementtimenetelmän tulosten perusteella staattorirakennetta voidaan yksinkertaistaa poistamalla nyt käytetty puristusrengas, jolloin rakenteesta tulee yksinkertaisempi ja kustannustehokkaampi.

Caracterização de membranas assimétricas de acetato de celulose produzidas a partir do aproveitamento do resíduo da palha de milho para uso em ultrafiltração

Cellulose acetates (CA) with different degrees of acetylation were synthesized from cellulose extracted from corn stover. Membranes were prepared for the ultrafiltration process with pure polymers and blend form of CA utilizing a dioxane/acetone system. The membranes were characterized according to their transport properties. The blend form materials presented the best results for application in ultrafiltration experiments. M-TAC/DAC (corn stover triacetate and diacetate) and M-TAC/DAC-Rho (corn stover triacetate and Rhodia diacetate) presented rejection to egg albumin protein of 87.39% and 80.50%, respectively. Thus, MWCO of 45 kDa was determined for these materials.

Experimento didático de quimiometria para planejamento de experimentos: avaliação das condições experimentais na determinação espectrofotométrica de ferro II com o-fenantrolina. Um tutorial, parte III

The objective of this manuscript is to describe a practical experiment that can be employed for teaching concepts related to design of experiments using Matlab or Octave computing environment to beginners, undergraduate and graduate students. The classical experiment for determination of Fe (II) using o-phenanthroline was selected because it is easy to understand, and all the required materials are readily available in most analytical laboratories. The approach used in this tutorial is divided in two steps: first, the students are introduced to the concept of multivariate effects, how to calculate and interpret them, and the construction and evaluation of a linear model to describe the experimental domain by using a 2³ factorial design. Second, an extension of the factorial design by adding axial points is described, thereby, providing a central composite design. The quadratic model is then introduced and used to build the response surface.

OBTENÇÃO E CARACTERIZAÇÃO DE MATERIAL HÍBRIDO ENTRE SÍLICA E CICLODEXTRINAS

The obtention of silica and cyclodextrin hybrid materials was accomplished by refluxing them in xylol using citric acid as a binding agent. The materials were characterized by infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and elemental analysis. Evidence for the docking of cyclodextrins α and γ was substantiated based on the variation in band intensity for groups such as ≡Si-OH. Additional docking evidence includes the displacement of some of the bands that are related to cyclodextrin such as the deformation of the C-H axial bond. The α and γ-CDSi materials were characterized as amorphous compounds. The products obtained in the synthesis showed changes in the decomposition temperatures of their isolated constituents, in which the mass of α and γ-CD docked to the silica surface gave the estimated values of 41% and 47%, respectively. The elemental constituents were shown to be consistent and close to their relative theoretical values. ​Thermogravimetric analysis showed that a reduction in the percentage of the hybrids was proportional to the amount of lost mass. This new material is an improvement over synthesized organosilane materials because the operator and the environment benefit from a less toxic methodology. In addition, the material has several potential applications in complexation systems with cyclodextrin.

Kostean höyryn paisunnan erityispiirteet ydinvoimalaitosten turbiineissa

Diplomityössä käsitellään ydinvoimalaitoksen kostean höyryn alueella toimivien höyryturbiinien toiminnan erityispiirteitä. Tarkemmin työssä keskitytään Loviisan ydinvoimalaitoksen turbiiniprosessiin. Tavoitteena on selvittää veden tiivistymistä höyryvirrassa, sen erotusta höyrystä turbiineissa sekä määrittää laitokselle todellinen paisuntakäyrä. Työssä selvitettiin veden tiivistymistä höyryvirtaan kirjallisuuden ja prosessista saatujen tietojen perusteella. Lisäksi työssä tutustuttiin suurien nykyaikaisten kostean höyryn alueella toimivien turbiinien vedenerotukseen ja sen pohjalta arvioitiin Loviisan ydinvoimalaitoksen turbiinin kosteudenerotusta. Näiden tietojen avulla saatiin mallinnettua kostean höyryn paisuntakäyrä Loviisan ydinvoimalaitoksen turbiineille. Työssä perehdyttiin lisäksi ulosvirtauskanavan toimintaan. Diplomityön puitteissa ei perehdytty yksityiskohtaisesti veden tiivistymiseen höyryvirrassa, vaan aihe ansaitsee tarkempaa tutkimusta. Kosteuden erotustehokkuuden arviointi todellisessa prosessissa ilman mittauksista saatavaa tietoa on vaikeata, mutta toimenpiteisiin lisäinformaation saamiseksi Loviisan ydinvoimalaitoksen turbiiniprosessista on ryhdytty. Työssä tehtyjen selvitysten avulla saatiin arvokasta tietoa turbiinikoneikon toiminnasta ja sen tehokkuuden parantamisesta.

Fatigue analysis of brackets with and without scallop for bridge and other deck structure using effective notch stress.

Due to functional requirement of a structural detail brackets with and without scallop are frequently used in bridges, decks, ships and offshore structure. Scallops are designed to serve as passage way for fluids, to reduce weld length and plate distortions. Moreover, scallops are used to avoid intersection of two or more welds for the fact that there is the presence of inventible inherent initial crack except for full penetrated weld and the formation of multi-axial stress state at the weld intersection. Welding all around the scallop corner increase the possibility of brittle fracture even for the case the bracket is not loaded by primary load. Avoiding of scallop will establish an initial crack in the corner if bracket is welded by fillet welds. If the two weld run pass had crossed, this would have given a 3D residual stress situation. Therefore the presences and absence of scallop necessitates the 3D FEA fatigue resistance of both types of brackets using effective notch stress approach ( ). FEMAP 10.1 with NX NASTRAN was used for the 3D FEA. The first and main objective of this research was to investigate and compare the fatigue resistance of brackets with and without scallop. The secondary goal was the fatigue design of scallops in case they cannot be avoided for some reason. The fatigue resistance for both types of brackets was determined based on approach using 1 mm fictitiously rounded radius based on IIW recommendation. Identical geometrical, boundary and loading conditions were used for the determination and comparison of fatigue resistance of both types of brackets using linear 3D FEA. Moreover the size effect of bracket length was also studied using 2D SHELL element FEA. In the case of brackets with scallop the flange plate weld toe at the corner of the scallop was found to exhibit the highest and made the flange plate weld toe critical for fatigue failure. Whereas weld root and weld toe at the weld intersections were the highly stressed location for brackets without scallop. Thus weld toe for brackets with scallop, and weld root and weld toe for brackets without scallop were found to be the critical area for fatigue failure. Employing identical parameters on both types of brackets, brackets without scallop had the highest except for full penetrated weld. Furthermore the fatigue resistance of brackets without scallop was highly affected by the lack of weld penetration length and it was found out that decreased as the weld penetration was increased. Despite the fact that the very presence of scallop reduces the stiffness and also same time induce stress concentration, based on the 3D FEA it is worth concluding that using scallop provided better fatigue resistance when both types of brackets were fillet welded. However brackets without scallop had the highest fatigue resistance when full penetration weld was used. This thesis also showed that weld toe for brackets with scallop was the only highly stressed area unlike brackets without scallop in which both weld toe and weld root were the critical locations for fatigue failure when different types of boundary conditions were used. Weld throat thickness, plate thickness, scallop radius, lack of weld penetration length, boundary condition and weld quality affected the fatigue resistance of both types of brackets. And as a result, bracket design procedure, especially welding quality and post weld treatment techniques significantly affect the fatigue resistance of both type of brackets.

Pulsatile Blood Flow Simulations in Computed Tomography(CT) Scan-Based and Idealized Geometries of Human Aorta

Blood flow in human aorta is an unsteady and complex phenomenon. The complex patterns are related to the geometrical features like curvature, bends, and branching and pulsatile nature of flow from left ventricle of heart. The aim of this work was to understand the effect of aorta geometry on the flow dynamics. To achieve this, 3D realistic and idealized models of descending aorta were reconstructed from Computed Tomography (CT) images of a female patient. The geometries were reconstructed using medical image processing code. The blood flow in aorta was assumed to be laminar and incompressible and the blood was assumed to be Newtonian fluid. A time dependent pulsatile and parabolic boundary condition was deployed at inlet. Steady and unsteady blood flow simulations were performed in real and idealized geometries of descending aorta using a Finite Volume Method (FVM) code. Analysis of Wall Shear Stress (WSS) distribution, pressure distribution, and axial velocity profiles were carried out in both geometries at steady and unsteady state conditions. The results obtained in thesis work reveal that the idealization of geometry underestimates the values of WSS especially near the region with sudden change of diameter. However, the resultant pressure and velocity in idealized geometry are close to those in real geometry

Atitude de Estudantes de Medicina frente a Terapias Alternativas e Complementares

O uso das Terapias Alternativas e Complementares (TAC) vem aumentando ao longo dos anos no Brasil e no mundo com o advento de políticas de saúde favoráveis ao emprego dessas práticas. No entanto, as escolas médicas ainda não oferecem disciplinas curriculares sobre este tema. Com o intuito de descrever as atitudes dos estudantes de Medicina de uma universidade do Sul do Brasil com relação às terapias complementares, foi realizado um estudo observacional transversal descritivo, por meio da aplicação de um questionário. Houve 65,22% de taxa de resposta, e a terapia mais conhecida pelos estudantes foi a Fitoterapia (90,3%). A maioria deles demonstrou atitudes favoráveis com relação às terapias, e 75,26% gostariam de aprender sobre o tema em aulas curriculares.

Pyörivien sähkökoneiden kotelointia koskevat standardit ja aksiaalivuokoneen jäähdytyksen kehittäminen

Tämä diplomityö on osa Lappeenrannan teknillisen yliopiston ja Visedo Oy:n yhteistyöprojektia. Työssä selvitetään pyörivien sähkökoneiden kotelointeja koskevia standardeja ja niiden vaikutukset koneiden suunnittelulle ja valmistukselle. Lisäksi työssä käsitellään aksiaalivuokoneen jäähdytykseen liittyviä ongelmia, kehitetään koneen nykyisiä jäähdytysratkaisuja ja ideoidaan käytettävissä olevia uusia jäähdytysmenetelmiä. Kehitysideoiden rajoitteena toimii koneelta vaadittu kotelointiluokka IP 64 – IP 68 sekä koneelle määritetty kestomagnetoitu aksiaalivuorakenne. Sähkökoneiden kotelointeja koskevien standardien asettamien vaatimusten määrittäminen tapahtui suurilta osin kirjallisuusselvityksenä. Standardien vaikutukset koneiden suunnittelulle ja valmistettavuudelle on selvitetty standardien kotelointien rakenteelle asettamien vaatimusten perusteella. Aksiaalivuokoneen jäähdytysongelmien selvittäminen, käytössä olevien jääh-dytysratkaisujen kehittäminen ja uusien menetelmien ideointi suoritettiin projektiluontoisesti yhdessä eri alojen asiantuntijoista koostuvan jäähdytystyöryhmän kanssa. Työn tuloksena laadittiin Visedo Oy:lle standardikäsikirja, jonka avulla Visedon sähkökoneiden tuoteperheeseen kuuluvien koneiden suunnitteluvaiheessa voidaan varmistaa koneiden standardienmukaisuus. Käsikirjassa on myös esitetty huomioita eri kotelointiluokkien asettamista vaatimuksista koneiden valmistukselle. Aksiaalivuokoneiden jäähdytykseen liittyen tavoitteena oli ratkaista aksiaalivuokoneisiin liittyviä jäähdytysongelmia. Työn tuloksena saa-tiin selville aksiaalivuokoneissa jäähdytyksen kehittämistä vaativat kohteet, laadittiin nykyisten jäähdytysratkaisujen parannusehdotuksia ja kehitettiin täysin uusia jäähdytysmenetelmiä.

Monitoring of centrifugal pump operation by a frequency converter

Centrifugal pumps are widely used in industrial and municipal applications, and they are an important end-use application of electric energy. However, in many cases centrifugal pumps operate with a significantly lower energy efficiency than they actually could, which typically has an increasing effect on the pump energy consumption and the resulting energy costs. Typical reasons for this are the incorrect dimensioning of the pumping system components and inefficiency of the applied pump control method. Besides the increase in energy costs, an inefficient operation may increase the risk of a pump failure and thereby the maintenance costs. In the worst case, a pump failure may lead to a process shutdown accruing additional costs. Nowadays, centrifugal pumps are often controlled by adjusting their rotational speed, which affects the resulting flow rate and output pressure of the pumped fluid. Typically, the speed control is realised with a frequency converter that allows the control of the rotational speed of an induction motor. Since a frequency converter can estimate the motor rotational speed and shaft torque without external measurement sensors on the motor shaft, it also allows the development and use of sensorless methods for the estimation of the pump operation. Still today, the monitoring of pump operation is based on additional measurements and visual check-ups, which may not be applicable to determine the energy efficiency of the pump operation. This doctoral thesis concentrates on the methods that allow the use of a frequency converter as a monitoring and analysis device for a centrifugal pump. Firstly, the determination of energy-efficiency- and reliability-based limits for the recommendable operating region of a variable-speed-driven centrifugal pump is discussed with a case study for the laboratory pumping system. Then, three model-based estimation methods for the pump operating location are studied, and their accuracy is determined by laboratory tests. In addition, a novel method to detect the occurrence of cavitation or flow recirculation in a centrifugal pump by a frequency converter is introduced. Its sensitivity compared with known cavitation detection methods is evaluated, and its applicability is verified by laboratory measurements for three different pumps and by using two different frequency converters. The main focus of this thesis is on the radial flow end-suction centrifugal pumps, but the studied methods can also be feasible with mixed and axial flow centrifugal pumps, if allowed by their characteristics.