Estudo da sinterização de eletrólito sólido de céria dopada com gadolínia

Fuel cells are electrochemical devices that convert chemical energy in electrical energy by a reaction directly. The solid oxide fuel cell (SOFC) works in temperature between 900ºC up to 1000ºC, Nowadays the most material for ceramic electrolytes is yttria stabilized zirconium. However, the high operation temperature can produce problems as instability and incompatibility of materials, thermal degradation and high cost of the surround materials. These problems can be reduced with the development of intermediate temperature solid oxide fuel cell (IT-SOFC) that works at temperature range of 600ºC to 800ºC. Ceria doped gadolinium is one of the most promising materials for electrolytes IT-SOFC due high ionic conductivity and good compatibility with electrodes. The inhibition of grain growth has been investigated during the sintering to improve properties of electrolytes. Two-step sintering (TSS) is an interesting technical to inhibit this grain growth and consist at submit the sample at two stages of temperature. The first one stage aims to achieve the critical density in the initiating the sintering process, then the sample is submitted at the second stage where the temperature sufficient to continue the sintering without accelerate grain growth until to reach total densification. The goal of this work is to produce electrolytes of ceria doped gadolinium by two-step sintering. In this context were produced samples from micrometric and nanometric powders by two routes of two-step sintering. The samples were obtained with elevate relative density, higher than 90% using low energy that some works at the same area. The average grain size are at the range 0,37 μm up to 0,51 μm. The overall ionic conductivity is 1,8x10-2 S.cm and the activation energy is 0,76 eV. Results shown that is possible to obtain ceria-doped gadolinium samples by two-step sintering technique using modified routes with characteristics and properties necessary to apply as electrolytes of solid oxide fuel cell

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Contribuição da catodoluminescência para o entendimento da diagênese da formação Jandaíra: áreas do campo de petróleo da fazenda Belém e Lajedo do Rosário

The general objective of this study was to contribute to the understanding of the chemical evolution of fluids that percolate through carbonate rocks of the Jandaíra Formation. The oxidation and reduction conditions in which grains, source and cement were formed was investigated using the cathodoluminescence technique (CL). The study area is located in the west part of the Potiguar Basin (Fazenda Belém field) and Rosário Ledge (Felipe Guerra municipality, State of Rio Grande do Norte, Brazil). The analysis of thin sections of carbonate rocks under CL revealed that grains (allochemical or not) and diagenetic products (micritization, dolomitization, neomorphism and cementation) exhibit since absence of luminescence the various luminescence colors (yellow, orange, red, brown, and blue) in a variety of intensities. As pure calcite shows dark blue luminescence, the occurrence of different luminescence colors in calcite crystals suggest one or more punctual crystal defects such as free electron, free space and impurity. The dyeing of thin sections with alizarin and potassium ferrocyanide revealed the absence of ferrous carbonate in the different lithotypes of Jandaíra Formation. Therefore, the different colors and intensities of CL observed in these rocks are probably caused by the presence of ion activators such as Mn2+ and is not an activator/inhibitor combination. In the same way, the absence of luminescence is very probably caused by the absence of activator ions and not due to the low concentration of inhibitor ions such as Fe2+. The incorporation of Mn2+ in the different members of the Jandaíra Formation must have been controlled by the redox state of the depositional environment and diagenesis. Therefore, it is possible that the luminescent members have been formed (e.g.,ooids) or have been modified (gastropod neomorphism) under reduction conditions in the depositional environments, in subsurface during the burial, or, in the case of Rosario Ledge samples , during the post-burial return to surface conditions. As regards the sudden changes from low to moderate and to strong luminescence, these features should indicate the precipitation of a fluid with chemical fluctuations, which formed the frequent zonations in the block cement of the Rosario Ledge samples. This study suggests that the different intensities and colors of CL should be correlated with the Mn2+ and Fe2+ contents, and stable isotopes of samples to determine the salinity, temperature, pH e Eh conditions during deposition

Evolução diagenética e caracterização dos reservatórios da seção devoniana na Bacia do Rio do Peixe-Nordeste do Brasil

The Rio do Peixe Basin represents a main basin of northeastern Brazil and pioneering work positioned the rocks of this basin in the Early Cretaceous. However, a recent study, based on integrated pollen analysis from three wells, found an unprecedented siliciclastic sedimentary section, in the region, of early Devonian age. Therefore, the present study aims a detailed petrographic and petrological analysis of this devonian section, in the Rio do Peixe Basin and proposes a diagenetic evolution, to understand the characteristics of the porous system, identify the main reservoir petrofacies with the main factors impacting on the quality of these rocks as reservoirs and a quick study on the provenance of this section. The petrographic study was based on samples obtained from subsurface and surface. The diagenetic evolution of petrofacies and its identification were based only on subsurface samples and the study of provenance was based on surface samples. The thin sections were prepared from sandstones, pelites and sandstones intercalated with pelites. The original detrital composition for this section is arcosean and the main diagenetic processes that affected these rocks occur in various depths and different conditions, which resulted in extensive diagenetic variety. The following processes were identified: early fracture and healing of grains; albitization of K-feldspar and plagioclase; siderite; precipitation of silica and feldspar; mechanical infiltration of clay and its transformation to illite/esmectite and illite; autigenesis of analcime; dissolution; autigenesis of chlorite; dolomite/ferrous dolomite/anquerite; apatite; calcite; pyrite; titanium minerals and iron oxide-hidroxide. The occurrence of a recently discovered volcanism, in the Rio do Peixe Basin, may have influenced the diagenetic evolution of this section. Three diagenetic stages affected the Devonian section: eo, meso and telodiagenesis. This section is compositionally quite feldspathic, indicating provenance from continental blocks, between transitional continental and uplift of the basement. From this study, we observed a wide heterogeneity in the role of the studied sandstones as reservoirs. Seven petrofacies were identified, taking into account the main diagenetic constituent responsible for the reduction of porosity. It is possible that the loss of original porosity was influenced by intense diagenesis in these rocks, where the main constituent for the loss of porosity are clays minerals, oxides and carbonate cement (calcite and dolomite)

Efeito antibacteriano de tecidos têxteis revestidos por prata através da técnica de deposição por plasma

In this study, it has been investigated the influence of silver film deposition onto 100% polyester woven and non-woven, on the survival of Escherichia coli and Staphylococcus aureus in contact with these surfaces. The treatment was performedin a chamber containing the working gas at low pressure (~ 10-2 mbar). Some process parameters such as as voltage: 470 V; pressure: 10-2 mbar; current : 0.40 A and gas flow: 6 and 10 cm3/min were kept constant. For the treatments with purêargon plasma using a flow of 6 and 10 cm3/min, different treatment times were evaluated, such as, 10 , 20, 30, 40, 50 and 60 minutes. Contact angle (sessile drop), measurements were used to determine the surface tension of the treated fabrics and its influence on the bacteria grow as weel as the possibilities of a biofilm formation. The formation of a silver film, as well as the amount of this element was verified byEDX technique. The topography was observed through scanning electron microscopy (SEM) to determine the size of silver grains formed on the surfaces of the fabric and assess homogeneity of treatment. The X-ray diffraction (XRD) was used to analyze the structure of silver film deposition. The woven fabric treatments enabled the formation of silver particulate films with particle size larger than the non-woven fabrics. With respect to bacterial growth, all fabrics were shown to be bactericidal for Staphylococcus aureus (S. aureus), while for the Escherichia coli (E. coli), the best results were found for the non-woven fabric (TNT) treated with a flow of 10 cm3/min to both bacteria

Estrutura da população de Coleodactylus natalensis Freire, 1999 (Squamata: Sphaerodactylidae) no Parque Estadual Dunas de Natal, Rio Grande do Norte, Brasil

Coleodactylus natalensis Freire, 1999, an endemic species of Atlantic Forest fragments around the Natal municipality, Rio Grande do Norte State, Brazil, has as type locality the Parque Estadual Dunas de Natal (05º48 S to 05º53 S and 35º09 W to 35º12 W), one of the largest restinga (herb and shrub association on sand dunes along the Brazilian coastline) associate fragment, surrounded by urban zone, placed on setentrional Atlantic Forest limits. We made estimates on populational density, spatial distribution, habitat and microhabitat preferences and feeding ecological aspects like sazonal and sexual variations on diet, prey electivities and niche breadth. We randomly sampled ninety-six 50m2 quadrants in each of the four habitats identified in the study area. Were collected 49 specimens and their stomach contents were analyzed; prey items found were correlated with leaf-litter invertebrates from habitat samples. We found a 98,5 ± 75,5 individuals/ha density, in grouped distribution pattern on densest habitats and random distribution on others habitats. This species lives mostly on leaf-litter in forest habitats, in higher humidity points, with lower temperatures, deeper leaf litter and lower sea level elevations than the randomly chosen points in the study area. Isopoda and Aranae were the most important prey categories in numeric, frequency and volumetric terms. Niche breadth has an intermediate value and was variable in sexual and in habitat terms. There was no correlation between morfometric measures and prey size on diet. The C. natalensis population studied seems to be diet opportunist, although selects larger prey items. The Parque Estadual das Dunas do Natal has several indications of anthropic pressure from the surrounding urban area that may affects the local C. natalensis population. Thus, the fragility of this species calls for urgent conservation efforts

Perdas fermentativas e composição bromatológica da entrecasca de palmito pupunha ensilada com aditivos químicos

Objetivou-se avaliar o efeito da inclusão de aditivos químicos na ensilagem de resíduos (entrecasca) da produção de palmito pupunha (Bactris gasipaes, Kunth). Utilizaram-se silos experimentais (baldes de 20 litros) providos de aparatos para determinação gravimétrica de perdas por gases e efluentes. Os tratamentos aplicados foram: controle (sem aditivos); ureia (1% da MV) e cal virgem (1% da MV). Decorridos 70 dias de armazenagem, os silos foram pesados, abertos e amostrados. As perdas por efluentes e gases aumentaram com a aplicação de cal virgem na ensilagem. As perdas totais de MS foram de 15,1; 14,4 e 26,6% nas silagens controle, ureia e cal, respectivamente. em todas as silagens, houve redução no teor de FDN e elevação da fração FDA, o que indica desaparecimento da fração hemicelulose. A relação cálcio:fósforo aumentou substancialmente com a adição de cal virgem, de 4,1:1 na silagem controle para 15,6:1 na silagem com cal. O resíduo da extração do palmito pupunha pode ser classificado como alimento de média qualidade e alto teor de umidade. Os aditivos aplicados na ensilagem não são efetivos em reduzir as perdas fermentativas no processo de conservação.

Cadmium availability and accumulation by lettuce and rice

Among the toxic elements, Cd has received considerable attention in view of its association with a number of human health problems. The objectives of this study were to evaluate the Cd availability and accumulation in soil, transfer rate and toxicity in lettuce and rice plants grown in a Cd-contaminated Typic Hapludox. Two simultaneous greenhouse experiments with lettuce and rice test plants were conducted in a randomized complete block design with four replications. The treatments consisted of four Cd rates (CdCl2), 0.0; 1.3; 3.0 and 6.0 mg kg(-1), based on the guidelines recommended by the Environmental Agency of the State of São Paulo, Brazil (Cetesb). Higher Cd rates increased extractable Cd (using Mehlich-3, Mehlich-1 and DTPA chemical extractants) and decreased lettuce and rice dry matter yields. However, no visual toxicity symptoms were observed in plants. Mehlich-1, Mehlich-3 and DTPA extractants were effective in predicting soil Cd availability as well as the Cd concentration and accumulation in plant parts. Cadmium concentration in rice remained below the threshold for human consumption established by Brazilian legislation. on the other hand, lettuce Cd concentration in edible parts exceeded the acceptable limit.

MELHORAMENTO do TRIGO: XXXI. HERDABILIDADES E CORRELAÇÕES ENTRE TRÊS CARACTERÍSTICAS AGRONÔMICAS em POPULAÇÕES HÍBRIDAS

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Períodos de dessecação de Urochloa ruziziensis e seu reflexo na produtividade da soja RR

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Épocas de manejo químico de Brachiaria decumbens antecedendo o plantio direto de soja

O manejo químico da cobertura vegetal e a manutenção da palhada sobre o solo são preocupações comuns para os produtores que adotam o sistema plantio direto na região dos cerrados. Com o objetivo de estudar a influência da época de manejo químico de B. decumbens sobre o desenvolvimento e a produtividade da cultura da soja em sistema plantio direto, foram realizados dois ensaios a campo, respectivamente, com os cultivares BRS 154 e MG/BR 46-Conquista, no ano de 2003. em cada ensaio, testaram-se quatro épocas de manejo de B. decumbens antecedendo a semeadura da soja (28, 14, 7 e 0 dias), utilizando-se o herbicida glifosato. Os ensaios foram conduzidos em delineamento inteiramente casualizado, utilizando-se três repetições no primeiro e quatro no segundo. Determinou-se a matéria seca da cobertura vegetal e avaliou-se a reinfestação de B. decumbens. Na cultura da soja, foram determinados: altura de inserção da primeira vagem, número de vagens por planta, umidade dos grãos, massa de 100 grãos e produtividade. Com base nos resultados obtidos, conclui-se que a época mais adequada para o manejo químico de B. decumbens com glifosato situa-se entre 7 e 14 dias antes da semeadura da cultura da soja e que a escolha da época de manejo químico da cobertura vegetal afeta de forma decisiva o desenvolvimento e a produtividade da cultura.

Período anterior à interferência das plantas daninhas para a cultivar de feijoeiro 'Rubi' em função do espaçamento e da densidade de semeadura

Os feijões estão entre os alimentos mais antigos, fazendo parte da alimentação diária da população brasileira. Objetivou-se com este trabalho determinar o período de convivência anterior à interferência das plantas daninhas (PAI) na cultura do feijoeiro em diferentes espaçamentos e densidades de plantas. Os tratamentos foram constituídos de períodos de convivência entre a cultura e as plantas daninhas, sendo zero a dez, zero a 20, zero a 30, zero a 40, zero a 50, zero a 60, zero a 70 e zero a 80 dias e mais uma testemunha sem convívio com as plantas daninhas. Além dos períodos de convivência, realizaram-se ainda estudos com espaçamentos entre linhas de 0,45 e 0,60 m e mais duas densidades de semeadura: dez e 15 plantas m-1. Adotou-se delineamento experimental de blocos casualizados, com quatro repetições. Quando o feijoeiro esteve presente com as plantas daninhas durante o ciclo, a produtividade dos grãos foi reduzida a 63, 50, 42 e 57% para os tratamentos com espaçamento de 0,45 m, densidades de semeadura de dez e 15 plantas m-1, espaçamento de 0,60 m e densidades de semeadura de dez e 15 plantas m-1, respectivamente. Os períodos anteriores à interferência (PAIs) da cultura foram de 23, 27, 13 e 19 dias após emergência, respectivamente.

Adubação nitrogenada para milho com o uso de plantas de cobertura e modos de aplicação de calcário

O sistema plantio direto (SPD) é uma realidade na região dos Cerrados, mas alguns questionamentos persistem nesse tipo de manejo como o modo de realização da calagem e a dose de nitrogênio (N) a ser adotada em cultura comercial, em relação às culturas precedentes. Desse modo, objetivou-se avaliar modos de aplicar o calcário na implantação do SPD e o efeito de culturas de cobertura precedentes sobre a necessidade de adubação nitrogenada da cultura do milho, durante diferentes anos agrícolas. O delineamento experimental utilizado foi de blocos casualizados, em esquema fatorial 5 x 2 (modos de aplicação do calcário x culturas de cobertura) e posterior divisão em três subparcelas, referentes às doses de N (0, 90 e 180 kg ha-1). Foram avaliados quatro modos de aplicação de calcário: incorporado a 0-0,2 m, em out./2001; dose total em superfície aplicada, em out./2001; aplicação de 1/2 da dose, em out./2001, e 1/2, em ago./2002, na superfície; e aplicação de 1/3 da dose recomendada, em mar./2001, + 1/3, em out./2001, e 1/3, em ago./2002, também em superfície. Além de um tratamento testemunha (sem calcário) e duas culturas de cobertura, crotalária e milheto. Os diferentes modos de calagem não alteraram a produtividade de grãos de milho. O cultivo de milho após crotalária apresentou melhor desempenho e menor demanda de adubação nitrogenada, quando comparado ao cultivado após milheto.