Conduction through thin titanium dioxide films

Conduction through TiO₂ films of thickness 100 to 450 Å have been investigated. The samples were prepared by either anodization of Ti evaporation of TiO₂, with Au or Al evaporated for contacts. The anodized samples exhibited considerable hysteresis due to electrical forming, however it was possible to avoid this problem with the evaporated samples from which complete sets of experimental results were obtained and used in the analysis. Electrical measurements included: the dependence of current and capacitance on dc voltage and temperature; the dependence of capacitance and conductance on frequency and temperature; and transient measurements of current and capacitance. A thick (3000 Å) evaporated TiO₂ film was used for measuring the dielectric constant (27.5) and the optical dispersion, the latter being similar to that for rutile. An electron transmission diffraction pattern of a evaporated film indicated an essentially amorphous structure with a short range order that could be related to rutile. Photoresponse measurements indicated the same band gap of about 3 ev for anodized and evaporated films and reduced rutile crystals and gave the barrier energies at the contacts.

The results are interpreted in a self consistent manner by considering the effect of a large impurity concentration in the films and a correspondingly large ionic space charge. The resulting potential profile in the oxide film leads to a thermally assisted tunneling process between the contacts and the interior of the oxide. A general relation is derived for the steady state current through structures of this kind. This in turn is expressed quantitatively for each of two possible limiting types of impurity distributions, where one type gives barriers of an exponential shape and leads to quantitative predictions in c lose agreement with the experimental results. For films somewhat greater than 100 Å, the theory is formulated essentially in terms of only the independently measured barrier energies and a characteristic parameter of the oxide that depends primarily on the maximum impurity concentration at the contacts. A single value of this parameter gives consistent agreement with the experimentally observed dependence of both current and capacitance on dc voltage and temperature, with the maximum impurity concentration found to be approximately the saturation concentration quoted for rutile. This explains the relative insensitivity of the electrical properties of the films on the exact conditions of formation.

Radiation from a short electric dipole antenna in a hot uniaxial plasma

The effects of electron temperature on the radiation fields and the resistance of a short dipole antenna embedded in a uniaxial plasma have been studied. It is found that for ω < ω_p the antenna excites two waves, a slow wave and a fast wave. These waves propagate only within a cone whose axis is parallel to the biasing magnetostatic field B_o and whose semicone angle is slightly less than sin ^(-1) (ω/ω_p). In the case of ω > ω_p the antenna excites two separate modes of radiation. One of the modes is the electromagnetic mode, while the other mode is of hot plasma origin. A characteristic interference structure is noted in the angular distribution of the field. The far fields are evaluated by asymptotic methods, while the near fields are calculated numerically. The effects of antenna length ℓ, electron thermal speed, collisional and Landau damping on the near field patterns have been studied.

The input and the radiation resistances are calculated and are shown to remain finite for nonzero electron thermal velocities. The effect of Landau damping and the antenna length on the input and radiation resistances has been considered.

The radiation condition for solving Maxwell's equations is discussed and the phase and group velocities for propagation given. It is found that for ω < ω_p in the radial direction (cylindrical coordinates) the power flow is in the opposite direction to that of the phase propagation. For ω > ω_p the hot plasma mode has similar characteristics.

Procedures to prevent the occurrence of potentially dangerous situations during the operation of the Mackereth 1-metre mini or short sediment corer

During the 1950s and 1960s, F.J.H. Mackereth developed and published plans for a series of pneumatic samplers for lake sediments. Unfortunately, as the equipment was continually evolving during ensuing research, no user manuals, beyond the original publication, had been produced. Over the last few years there have been a few potentially very serious accidents with the 1-metre corer, which has prompted the authors to carry out a risk assessment. This highlighted two weaknesses in the design and its later developments. They can be corrected simply by checking for screw threads that may have been added to the exhaust port on the mini-corer, and by changing the operating procedure. An A4 nine-page user manual is now available from the authors. A small charge ( pound sterling 10 in 1998) will be made to cover handling costs and postage.

Biodiversity of macrozoobenthos in a large river, the Austrian Danube, including quantitative studies in a free-flowing stretch below Vienna: a short review

The Danube is ca. 2850 km in length and is the second largest river in Europe. The Austrian part of the Danube falls 156 metres in altitude over its 351 km length and, since the early 1950s, the river has been developed into a power-generating waterway, so that the continuity of the river is now interrupted by ten impounded areas. Only two stretches of the original free-flowing river are left, the Wachau region (above river-km 2005, west of Vienna) and the region downstream from the impoundment at Vienna (river-km 1921). Most of the recent theories and concepts related to invertebrates, in the context of the ecology of running waters, are based on studies on small streams, whereas investigations of large rivers have played a minor role for a long time, mainly due to methodological difficulties. The authors' recent detailed studies on macroinvertebrates in the free-flowing section of the Danube below Vienna, provide an excellent opportunity to survey or restate scientific hypotheses on the basis of a large river. In this review the main interest focuses on the investigation of biodiversity, i.e. the number of species and their relative proportions in the whole invertebrate community, as well as major governing environmental factors. The article summarises the species composition, the important environmental variables at the river cross-section and the effect of upstream impoundment on the riverbed and its fauna.

Marketing of the Spanish film industry in the entertainment market

This project analyzes the role that marketing plays at present.It is a distinctive in the film industry because of the emergence of new patterns of production, distribution and exhibition due to the unstoppable progress of digital technologies, the expansion of the internet and consumer changes in the spectator. To perform this analysis, a description of the situation of the film industry in the competitive market, Hollywood, and the evolution of digital technology in general are included. It is also essential in the project, to observe, the marketing applied to the different phases of the globalized cinema. And then introduce the potential Spanish marketing strategies.

Glycocalyx production in teleosts [Translation from: Verhandlungen der Deutschen Zoologischen Gesellschaft, p.286, 1970]

Shielding the organism against harmful effects from the environment is one of the most important tasks of the outer covering of all animals. The epidermis of primarily aquatic organisms and the epithelia of organs which are exposed to water, such as the digestive or the urinary system, possess a film of glycoproteins and mucopolysaccharides, the glycocalyx. This short paper examines the relationship of the mucus cells with the glycocalyx.

A short thesis on arc-welding

During the past few years the attention of architects, engineers and others encased in or connected with the building industry has been attracted to the possibilities of the application of welding processes to the joining of structural members. As oxy-acetylene welding was developed before electric arc welding became perfected it was only natural that the gas torch should be first considered. It developed however on examination of the two processes that while acetylene welding gave better results in most cases it was only in the hands of experts that it could consistently outscore the arc as a welding medium. Arc-welding has the advantage over the acetylene process, where each individual operator must use his own judgement as to the proper flame, in that a squad of arc-welders can work under the direction of a single expert supervisor who accepts the responsibility of fixing the current value and of determining the proper size of welding rod to be used on any given type of work.