Non-linear dynamics of a tower orchard sprayer based on an inverted pendulum model

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Extensive Comparisons of Optical Fast-OFDM and Conventional Optical OFDM for Local and Access Networks

A performance comparison between a recently proposed novel technique known as fast orthogonal frequency-division multiplexing (FOFDM) and conventional orthogonal frequency-division multiplexing (OFDM) is undertaken over unamplified, intensity-modulated, and direct-detected directly modulated laser-based optical signals. Key transceiver parameters, such as the maximum achievable transmission capacity and the digital-to-analog/analog-to-digital converter (DAC/ADC) effects are explored thoroughly. It is shown that, similarly to conventional OFDM, the least complex and bandwidth efficient FOFDM can support up to similar to 20 Gb/s over 500 m worst-case multimode fiber (MMF) links having 3 dB effective bandwidths of similar to 200 MHz X km. For compensation of the DAC/ADC roll-off, a power-loading (PL) algorithm is adopted, leading to an FOFDM system improvement of similar to 4 dB. FOFDM and conventional OFDM give similar optimum DAC/ADC parameters over 500 m worst-case MMF, while over 50 km single-mode fiber a maximum deviation of only similar to 1 dB in clipping ratio is observed due to the imperfect chromatic dispersion compensation caused by one-tap equalizers.

Planejamento e controle da produção de cilindros para laminação: um estudo de caso quantitativo

Este trabalho apresenta um modelo de otimização-simulação aplicado em um estudo de caso real no setor de cilindros para laminação de uma siderúrgica, buscando melhorar o gerenciamento da área/equipamento gargalo da linha de produção. A simulação atuou em conjunto com um modelo de otimização da programação linear inteira (PLI) para melhorar o atendimento de prazo junto aos clientes em uma produção não seriada. Como resultado deste procedimento combinado da PLI e simulação, o processo produtivo foi otimizado e as filas de espera e o lead-time foram reduzidos, melhorando o atendimento aos clientes.

Caracterização mecânica e térmica de compósitos de poli (cloreto de vinila) reforçados com fibras de sisal

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A tunable triode-MOSFET transconductor and its application to g(m)-C filters

A linear, tunable CMOS transconductance stage is introduced. Drain voltage of the input transistor operating in triode region is settled by a regulation loop and a first-order linear relationship between g(m) and a de bias voltage is achieved. In addition to easy tuning, this technique offers circuit simplicity, wide dynamic range, high input and output impedances and low consumption. The transconductor is presented on both single-ended and fully-differential versions. A 3rd-order elliptical low-pass g(m)-C filter with a nominal roll-off frequency of 2MHz is used as one example for the many applications of the proposed transconductor. SPICE data describe circuits performances and filter tunabilily Passband is tuned at a rate of 2.36KHz/mV and good linearity is indicated by a 0.89% THD for an 800mV(p-p) balanced-driven input.

Vermiculita como substrato para o teste de germinação de sementes de barbatimão

The objective of this research was to evaluate the use of vermiculite as a substrate for the germination test of 'barbatimao' seeds and to establish what would be the best granulometry and the best moisture intensity to germinate 'barbatimao' seeds. Four replications of 50 seeds were previously scarified with H(2)SO(4) for 60 minutes. Afterwards, the following germination substrates were evaluated: paper rolls moistened with water equivalent to 2.5 times the weight of the dry paper (control); micron, super thin, thin and average sized vermiculite moistened with 0.5, 1.0, 1.5 and 2.0 times the weight of the dry paper. The germination temperature was 30 C. The percentage of normal seedlings was obtained seven days after sowing (first count) and, then, weekly (up to 28 days). Average time and relative distribution of germination were calculated. It was concluded that the germination of 'barbatimao' seeds can be carried out with either fine vermiculite moistened with water equivalent to 2.0 times the weight of the dry paper or average sized substrate moistened with water equivalent to 0.5 to 2.0 times the weight of dry paper. These treatments resulted in higher and faster germination (21 days), similarly to the paper roll method.

Hydrodynamic aspects of the amorphous alloy ribbon fabrication

Conditions for as-quenched amorphous ribbon fabrication by a single roll-casting method are analyzed from a hydrodynamic standpoint. The analysis is based on the investigation of the processing conditions for Fe 4 0Ni 40P 14B 6 amorphous ribbons. It is shown that the dependence of ribbon thickness on the ejection pressure for different roll angular velocities and different dimensions of crucible and orifice can be obtained from general considerations on the melt flow regime.

The use of shallow seismic reflection technique in near surface exploration of urban sites: An evaluation in the city of SãO Paulo, Brazil

In order to evaluate the use of shallow seismic technique to delineate geological and geotechnical features up to 40 meters depth in noisy urban areas covered with asphalt pavement, five survey lines were conducted in the metropolitan area of São Paulo City. The data were acquired using a 24-bit, 24-channel seismograph, 30 and 100 Hz geophones and a sledgehammer-plate system as seismic source. Seismic reflection data were recorded using a CMP (common mid point) acquisition method. The processing routine consisted of: prestack band-pass filtering (90-250 Hz); automatic gain control (AGC); muting (digital zeroin) of dead/noisy traces, ground roll, air-wave and refracted-wave; CMP sorting; velocity analyses; normal move-out corrections; residual static corrections; f-k filtering; CMP stacking. The near surface is geologically characterized by unconsolidated fill materials and Quaternary sediments with organic material overlying Tertiary sediments with the water table 2 to 5 m below the surface. The basement is composed of granite and gneiss. Reflections were observed from 40 milliseconds to 65 ms two-way traveltime and were related to the silt clay layer and fine sand layer contact of the Tertiary sediments and to the weathered basement. The CMP seismic-reflection technique has been shown to be useful for mapping the sedimentary layers and the bedrock of the São Paulo sedimentary basin for the purposes of shallow investigations related to engineering problems. In spite of the strong cultural noise observed in these urban areas and problems with planting geophones we verified that, with the proper equipment, field parameters and particularly great care in data collection and processing, we can overcome the adverse field conditions and to image reflections from layers as shallow as 20 meters.

Continuous production of metal matrix composites from the semisolid state

Continuous strip metal matrix composite (MMC) casting of 0.3 mm diameter hard-drawn stainless steel (316L) wire in a quasi-eutectic SnPb (64Sn36Pb) matrix was performed by a two-roll melt drag processing (TRMDping) method, with the wire being dragged through a semisolid puddle with a fibre contact time of approximately 0.2 s. A slag weir placed at the nozzle contained two wire guide holes: one located near the upper roll, and the other located between the rolls. A successful continuous composite strip casting with good fibre alignment was achieved by inserting and embedding the wire into the matrix using the guide hole between the rolls. Degeneration of eutectic/dendrite structures led to the formation of globular structures. The occurrence and formation mechanisms of cracks, de-lamination and voids in the matrix were discussed. TRMDping is economically viable and has significant benefits over other MMC fabrication methods. © (2013) Trans Tech Publications, Switzerland.

Efeitos do tramadol no modelo de dor induzida por obstrução intestinal em eqüinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fertilização artificial de ovócitos de curimbatá, Prochilodus lineatus

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito da lisina na produção de compostos beta-lactâmicos produzidos por Sterptomuces clavuligerus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da adubação nitrogenada e potássica em pomar de goiabeiras

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Avaliação do tempo e métodos de aquecimento de toras de Eucalyptus grandis Hill ex-Maiden e sua influência no rendimento em laminação e na qualidade das lâminas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Santinho do pau oco: sensualidade e religiosidade nos romances do Padre Antônio da Fonseca

Pós-graduação em Letras - FCLAS