Experimento para quantificar a eficiência de aspersão de líquidos: aplicação em distribuidores espinha de peixe

This paper describes a device developed on the pilot scale and a simple approach to compare liquid distributor efficiencies. The technique consists basically of analyzing the mass of the liquid collected in 21 vertical pipes measuring 52 mm in internal diameter and 800 mm in length placed in a quadratic arrangement and positioned below the distributor A 50 mm thick acrylic blanket that does not disperse liquids was placed between the distributor and the pipe bank to avoid splashes. Assays were carried out with ladder-type distributors equipped with 4 parallel pipes each for a column measuring 400 nun in diameter as an example of the application. The number (n) of orifices (95, 127, and 159 orifices/m(2)), orifice diameter (d) (2, 3, and 4 mm) and the flowrate (q) (1.2; 1.4; and 1.6 m(3)/h) were varied. The best spread efficiency, which presented the lowest standard deviation, was achieved with 159 orifices, 2 mm and 1.4 m(3)/h. The pressure (p) at the distributor inlet for this condition was only 51000 Pa (0.51 kgf/cm(2)), while the average velocity (v) was 6.3 m/s in each orifice. These results show some limitations of the practical rules used in distributor designs.

Structural evolution of Eu-doped hydroxyapatite nanorods monitored by photoluminescence emission

This paper reports the synthesis of Eu-doped hydroxyapatite (HA:Eu) resulting in particles with nanorod diameters from 9 to 26 nm using the microwave hydrothermal method (HTMW). Eu3+ ions were used as a marker in the HA network by basic hydrolysis followed by the HTMW treatment. The crystalline HA:Eu nanorod nature in a short-range order was detected by photoluminescence (PL) measurements from Eu3+ emission into the HA matrix. Thus, was possible to verify that HA crystallization is favored in a short structural order when the HTMW treatment time was increased from 0 to 40 min and that the Eu3+ substitution in the HA lattice is site-selective. (C) 2012 Elsevier B.V. All rights reserved.

Corrosion protection of aluminium alloy by cerium conversion and conducting polymer duplex coatings

The corrosion protection of AA6063 aluminium alloy by cerium conversion, polyaniline conducting polymer and by duplex coatings has been investigated. The electrochemical behaviour was evaluated in aerated 3.5 wt.% NaCl. All coatings tested shifted the corrosion and pitting potentials to more positive values, indicating protection against corrosion. The duplex coatings are significantly more effective than each coating alone: corrosion and pitting potentials were shifted by +183 and +417 mV(SCE), respectively, by duplex coatings in relation to the untreated aluminium alloy. Optical microscopy and scanning electron microscopy are in agreement with the electrochemical results, reinforcing the superior performance of duplex coatings. (C) 2012 Elsevier Ltd. All rights reserved.

Comparative study on structure and magnetic properties of polycrystalline PrxY1-xBa2Cu3O7-delta prepared in oxygen and argon atmosphere

We report a systematic study on the influence of the synthesis routes on the structural and magnetic properties of polycrystalline PrxY1-xBa2Cu3O7-delta. We have prepared high-quality samples of this material by following a sol-gel method based on heat treatment in both inert argon and oxygen atmospheres in order to compare their effect on the formation of the superconducting phase using X-ray powder diffraction. Magnetic measurements (DC and AC susceptibility) clearly demonstrate that, for the same concentration of Pr, the superconducting transition temperature markedly increases in all samples prepared in argon atmosphere, including pure Pr-123. (C) 2012 Elsevier B.V. All rights reserved.

Indicadores-chave de desempenho e a gestão integrada da mineração

The exceptional advance of information technology and computer application to the mineral sector has allowed the automation of several processes of the mineral value chain. ERP systems (Enterprise Resource Planning) provided the platform for the efficient integration of all support activities of the mineral value chain. Despite all advances gathered with the application of computers, it was not possible to date, to effectively integrate the primary activities of the mineral value chain. The main reason for that are the uncertainties present in the productive process, which are intrinsic to the business, and the difficulty to quantify and qualify the benefits obtained with this integration due to the lack of a clear definition of the key performance indicators (KPIs). This work presents an analysis of the ERP systems application in Brazilian mining, identifies the KPIs of some of the most important Brazilian mining companies, and discusses the importance of mapping and measuring these indicators for the effective. management of the mining business.

On the stability of the Higher Manganese Silicides

We investigated in this work the stability of the Higher Manganese Silicides (HMS). Several alloys in the composition range 62-66 at.% Si were prepared from their constitutive elements by arc-melting. The prepared alloys were then analysed by in situ X-ray diffraction measurements and Electron Probe Micro-Analyser (EPMA). The whole results allow us to suggest that whatever the composition is, only Mn(27)Si(47) is stable for the temperatures 500 degrees C and 800 degrees C. At higher temperatures, the studied samples undergo two phase transformations which consecutively lead to the formation of Mn(15)Si(26) and Mn(11)Si(19). Mn(4)Si(7) was never evidenced in the present work. It is shown for the first time in this work that Mn(27)Si(47) is the only HMS stable phase at room temperature. (C) 2011 Elsevier B.V. All rights reserved.

Nonoriented Electrical Steels

The physical origins of the magnetic properties of nonoriented electrical steels; its relations to microstructural features like grain size, nonmetallic inclusions, dislocation density distribution, crystallographic texture, and residual stresses; and its processing by cold rolling and annealing are overviewed, using quantitative relations whenever available.