The main factor influencing the tensile properties of surface nano-crystallized graded materials

The improved mechanical properties of surface nano-crystallized graded materials produced by surface severe plastic deformation ((SPD)-P-2) are generally owing to the effects of the refined structure, work-hardened region and compressive residual stress. However, during the (SPD)-P-2 process, residual stress is produced simultaneously with work-hardened region, the individual contribution of these two factors to the improved mechanical properties remains unclear. Numerical simulations are carried out in order to answer this question. It is found that work hardening predominates in improving the yield strength and the ultimate tensile strength of the surface nano-crystallized graded materials, while the influence of the residual stress mainly emerges at the initial stage of deformation and decreases the apparent elastic modulus of the surface nano-crystallized graded materials, which agrees well with the experimental results. (C) 2010 Elsevier B.V. All rights reserved.

Extinction of lean near-limit methane/air flames at elevated pressures under normal- and reduced-gravity

perimentally at evaluated pressures and under normal- and micro-gravity conditions utilizing the 3.5 s drop tower of the National Microgravity Laboratory of China. The results showed that under micro-gravity conditions the natural convection is minimized and the flames become more planar and symmetric compared to normal gravity. In both normal- and micro-gravity experiments and for a given strain rate and fuel concentration, the flame luminosity was found to enhance as the pressure increases. On the other hand, at a given pressure, the flame luminosity was determined to weaken as the strain rate decreases. At a given strain rate, the fuel concentration at extinction was found to vary non-monotonically with pressure, namely it first increases and subsequently decreases with pressure. The limit fuel concentration peaks around 3 and 4 atm under normal- and micro-gravity, respectively. The extinction limits measured at micro-gravity were in good agreement with predictions obtained through detailed numerical simulations but they are notably lower compared to the data obtained under normal gravity. The simulations confirmed the non-monotonic variation of flammability limits with pressure, in agreement with previous studies. Sensitivity analysis showed that for pressures between one and 5 atm, the near-limit flame response is dominated by the competition between the main branching, H + O2 ? OH + O, and the pressure sensitive termination, H+O2+M? HO2 + M, reaction. However, for pressures greater than 5 atm it was determined that the HO2 kinetics result in further chain branching in a way that is analogous to the third explosion limit of H2/O2 mixtures. 2010 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

川西亚高山森林生态系统辐射传输研究

辐射传输研究是贯穿森林生态系统的纽带，太阳辐射为植物的生长发育提供光合能量、适宜的环境温度以及发育信息。一方面，气候变化使到达地面辐射能的质和量发生变化，影响到植被的生长发育，改变森林的结构，而森林结构的变化又会影响林冠内辐射能的分配和质量，这些变化会进一步影响到林下土壤温度，改变森林根系活性以及土壤营养转化的效率；连锁反应的结果有可能会使森林生态系统的生产力发生变化，改变碳素和氮素源库的调节方向，从而反馈影响地球气候系统。另一方面，人类作为生态系统的成员，必然需要森林生态系统为其提供更多的原材料和更好的生态服务功能，如何实现这些目标，就需要人类适度调整干预方式和频度，达到预期的目的。本文在建立适合于川西亚高山森林的叶面积测量技术、光照辐射模型和土壤温度变化模型的基础上，对川西亚高山地带森林生态系统的辐射传输特征进行了分析，并从森林结构的角度探讨了林分内的辐射分布以及对土壤温度的影响。主要成果如下： 1. 提出了一种照相法测量叶面积的方法。通过对摆放在平面上的叶片照相，利用投影变化，把非正射图像转化为正射图像，然后经过计算机图像处理得到每一片叶片的面积、周长、长度、宽度等信息。这种方法可使用户以任意方向和距离拍摄处于平面上的叶片，能同时处理大量的叶片，适于野外离体或活体叶片测量。叶片面积分辨率可调，分辨率可以与常用的激光叶面积仪相近甚至更高，而且叶片图像可以存档查询。 2. 提出一种模拟林内光照变化的模型。利用林冠半球照片，记录视点以上半球内的林冠构件空间分布，作为林冠子模型；天空辐射子模型采用国际照明委员会(CIE)的标准晴天和阴天以及插值模型。该模型能够模拟林下某一位点处的实时光斑变化。 3. 提出一种土壤温度变化模型。把土壤视为具有容量和阻力性质的结构，利用电阻和电容器件构建土壤能量分布模型。外界太阳辐射能经过植被以及其它一些能量分配器后进入土壤，其中有一部分转化为土壤势能，即土壤温度。土壤温度的变化类似于电池的充放电过程。在已知模型参数的情况下，可以从太阳辐射计算土壤温度的变化。在模型参数未知的情况下，通过输入和输出值推算模型的参数，而模型参数中的时间常数与土壤组成和含水量有关，这样就可以知道土壤水分的变化情况。 4. 从王朗亚高山森林典型样地林分结构的测量获得林地三维结构图、树冠形态、叶面积密度等参数，这些参数输入到Brunner (1998)开发的tRAYci 模型中计算出一段时间内林分任意位置处的光照值。与林下辐射计测量值以及半球照片计算结果的比较，该模型基本上能够满足对林分光环境了解的要求。 5. 从川西亚高山森林生产力的角度，探讨了森林生产力研究的方法以及川西地区的研究历史和成果，发现了其中的一些规律和问题，特别是在叶面积测量上，还没有使用标准的叶面积指数定义。综合来看，川西地区针叶林叶面积指数(单位土地面积上植物冠层总叶面积的一半) 应在4-5 之间。降雨丰富的华西雨屏带是川西地区森林生产力最高的地区，而向西北森林生产力逐渐降低。川西地区云冷杉林森林生产力平均约为600 gDM m-2 a-1，但是根据辐射能计算的潜在生产力则达到1800 gDM m-2 a-1。实际与潜在森林生产力的巨大差异说明其它因子对生产力的影响。 6. 王朗亚高山3 个典型森林林分中，白桦林样地(BF) 林下草本以糙野青茅、牛至、紫菀等喜阳性物种为主，林下透光度较高；冷杉林样地(FF) 林下透光度最低，以喜阴性物种水金凤、蟹甲草、囊瓣芹等为主；而云杉林样地(SF)林分林龄最大，林下透光度介于冷杉林和白桦林之间，草本层仍然以喜阴性物种东方草莓、紫花碎米芥、酢浆草等为主。冷杉林和云杉林的灌木层也很丰富，卫矛属、五加属、茶藨子属、忍冬属植物很丰富，而在白桦林则以栒摘要子属、榛子属、鹅耳枥属等植物为主。藓类植物在云杉林中最丰富，并且形成毯状层，其它两个林分则很稀少。3 个样地林分结构与林下光环境有很强的相关性，从光环境特征可以在一定程度上推测林分的结构。各样地单纯从乔木层材积推算的NPP 排列顺序为BF>FF>SF，与林下辐射透射率和林分年龄的顺序相同，暗示辐射对群落演替过程的驱动作用。 7. 用半球照相法测得BF、FF 和SF 3 个样地的有效叶面积指数以SF 样地最高，BF 最低。如果考虑针叶树叶片在小枝上的丛聚分布，利用北方针叶林的数值进行校正，则SF 样地LAI 显著增加(达到89%)，其它样地的LAI 基本不变甚至有所下降。校正后的数值与文献中地面测量的结果较相近，说明在使用半球照相法测量川西亚高山针叶林LAI 时必须加以校正。 8. 在3 个样地中，白桦、岷江冷杉和方枝柏种群为丛聚分布，紫果云杉在FF和SF 样地中基本上为随机分布。3 个物种出现丛聚分布的最短距离约为2m，在最短距离以内则为随机分布。最短距离可能与树冠大小有关，种子传播特征以及对光照的需求状况可能是造成这种分布格局类型的原因。 Radiative transfer plays a key role in forest ecosystems. Solar radiation providesenergy for photosynthesis, appropriate ambient temperature and development informationfor plants. However, quality and quantity of radiation reaching land surface are affected byweather and subsequently influence the growth and development of plants, which in turnchanges the budget of radiation in forest. Soil temperature changes with the variation ofradiation under forest canopy and influences the activity of roots and rate of nutrientturnover. Thus, any changes of radiation will induce chain reactions in the entireecosystem and display in the value of net primary productivity which will possibly shiftthe relationship between carbon source and sink at local or regional scale and feed back tothe global climate system. On the other hand, as a component of ecosystems, humanbeings of course need to demand more materials and better service from ecosystems. Forthese purpose, man must adapt their pattern and frequency of interference to ecosystems.This paper aims to research on the canopy structure, the radiation distribution and theirinfluence on soil temperature from the process of radiative transfer in subalpine forestecosystem of western Sichuan. The main results are: 1 Present a new photogrammetric method for leaf area. The main idea is to convertnon-vertically taken images of planar leaves to orthoimages through projectivetransformation. The resultant images are used to get leaf morphological parametersthrough image processing. This method enables users to take photos at almost anyorientation and distance if only the leaves are placed on same plane, and to processlarge quantity of leaves in a short time, which is suitable for field measurement. Theresolution of leaf area is adjustable to fit for special requirement. 2 A model using hemispherical photos combining with solar tracks and radiation courseis provided to simulate light variation in forest. The hemispherical photos of canopyrecord the real spatial distribution of each element of plants viewed from a point. Skyradiance is simulated with CIE standard clear sky or cloudy sky model. This modelcan be used to simulate real time light variation under canopy. 3 Present a soil temperature model. Soil could be regarded as a body of resistor andcapacitor. Some of the budget of solar radiation in soil body is transformed into soilpotential energy, the soil temperature. Variation of soil temperature is driven by solarradiation, vegetation, soil properties, etc. This model has two parameters, one of whichis time constant and is related to soil water content. The inversed model can be used tosimulate the variation of soil water. 4 By using model tRAYci developed by Brunner (1998), the 3-D distribution of light inthree subalpine forest stands of Wanglang Nature Reserve has been simulated andvalidated with value of radiometers in these stands. This model can basically satisfythe need for understanding light regimes of these stands. 5 Present some principles and questions of NPP (net primary of productivity) researchesin western Sichuan. The standard leaf area index (LAI) defined by Chen and Black(1997) has not been used in this region. Total leaf area and projected leaf area indexare still used in NPP researches which may differ around 1-fold in magnitude. Thestandard LAI which is a half of total leaf area above unit land area should be between4 and 5 for typical subalpine coniferous forest of western Sichuan concluded fromliteratures. The maximum forest NPP occurs in West China rain belt and decreasesnorthwestwards. Average NPP of spruce-fir forest in western Sichuan is about600gDM m-2 a-1, which is below the potential NPP of 1800gDM m-2 a-1 based onmeasured radiation in this region. The significant difference between potential and realNPP suggests that other factors influence the growth of stands. 6 In the three subalpine forest stands of Wanglang Nature Reserve, herbage layer ofAbstractbirch stand (BF) with age of 40 is dominated by heliophytes of Deyeuxia scabrescens,Origanum vulgare, Aster tongoloa etc.. However, both of the other two stands aredominated by shade tolerent species, such as Impatiens noli-tangere, Impatiensdicentra, Cacalia deltophylla and Pternopetalum tanakae etc. in fir stand (FF) withage of 180 and Fragaria orientalis, Cardamine tangutorum and Oxalis corniculata etc.in spruce stand (SF) with age of 330. Shrub species in the latter two stands arerelatively rich, typical dominant genera being Euonymus, Acanthopanax, Ribes andLonicera. Birch stand has relatively sparse shrubs dominated by genera of Cotoneaster,Corylus and Carpinus. Mosses are significant only in spruce stand. The canopystructure controls the light regime of stand, which influence the composition of herblayers beneath the canopy. This light regime-community structure relationship can beused to infer the herb community from canopy structure. The NPP derived from timbervolume of arbor layer of the three stands decreases from BF to SF, which is in thesame order of transmitted total radiation under canopy and age of these stands,suggesting the driving effect of radiation in the succession of community. 7 The highest effective LAI of the three stands obtained by hemispherical photos is inplot SF and lowest in plot BF. After rectification of the clumping effect of leaves onshoot, the real LAI in plot SF increases significantly (89%) and approximate to theaverage LAI of coniferous forest in western Sichuan. Therefore, the LAI obtainedfrom hemispherical photos needs rectification for clumping effect. 8 Spatial distribution pattern for Betula platyphylla, Abies faxoniana and Sabinasaltuaria is clumpy, but Picea purpurea almost random in plot FF and SF. The shortestdistance for clumpy distribution for Betula platyphylla and Sabina saltuaria is 1.5m,and 2m for Abies faxoniana. And random pattern for these trees is exhibited within thisrange which almost coincides with the diameter of crown. Seed dispersalcharacteristics and light requirement may be the reason for different spatial pattern.

小麦胚乳蛋白组分和Glu-B3位点基因核心编码区差异与小麦品质关系的研究

小麦加工品质改良已成为我国小麦育种的主要目标之一。特别是我国加入WTO以后，对小麦产品的质量提出了更高的要求，小麦品质改良的任务将更加艰巨和重要，小麦胚乳蛋白是影响小麦加工品质性状的重要因素。因此，深入了解小麦胚乳蛋白对加工品质性状的影响及其分子基础，为品质改良提供理论依据和科学指导，对加速我国小麦品质育种和优质小麦生产具有重要意义。本研究选用在麦谷蛋白5个基因位点(Glu-A1、Glu-B1、Glu-D1、Glu-B3和Glu-D3)上均含不同等位基因的小麦品种99G45和京771及Pm97034和京771杂交F9代共164个麦谷蛋白纯合系，及228个中国推广普通小麦品种和高代育成品系为试材，研究了麦谷蛋白Glu-1和Glu-3位点基因等位变异对籽粒蛋白、湿面筋含量、Zeleny沉降值和SDS沉降值间的关系；本研究还利用小麦A、B和D基因组中低分子量麦谷蛋白亚基（LMW-GS）基因特异引物，通过PCR方法克隆了1个Glu-A3位点和3个Glu-B3位点LMW-GS基因片段，在此基础上分析了不同等位基因对品质造成差异的分子基础；另外，本研究对中国近年推广的部分品种和育成的高代品系资源的多样性进行了分析。现将主要研究结果简述如下： 1. 对来自三个麦区的148份材料的醇溶蛋白组成进行了分析，结果表明，各麦区醇溶蛋白模式具有较大差异。在ω区,A7、B、E、F、G、J、P、Q、S和U仅存在于西南秋播麦区；A3、M、N、R、W和X仅存在于黄淮特种麦区；K仅存在于北方冬麦区；A6是北方冬麦区出现频率最高的带型模式，而西南秋播麦区中D出现的频率最高。ω-区的E、H和M几种模式是以前国内外未曾报道的。且初步确定，这些模式对品质性状具有正效应。至于γ区,A、B、D、E和F在各区均有出现，其中B和E在各区出现的频率都很高，在26.1-39.6％之间。相反，H 仅出现在黄淮特种麦区，J仅限于西南秋播麦区。对于β-区醇溶蛋白，B型模式在所有区中都相当高，而模式A仅存在于第三区.对于α-区，模式A在Ⅲ区而模式D在Ⅱ区出现的频率很高。1BL.1RS易位系在中国小麦品种中出现频率高达41.2％，在I, II和Ⅲ麦区的出现频率分别为 45.5、43.5和35.2%。各生态区模式的差异可能是品种适应不同生态条件和人为选择的结果，但这有待进一步证明。由于醇溶蛋白位点（Gli-1）与LMW-GS位点（Glu-3）紧密连锁，本结果可为下面确定普通小麦LMW-GS等位基因变异所用。 2. 利用Gli-1与Glu-3的紧密连锁，以228个小麦品种/系为材料，首次对中国小麦品种麦谷蛋白亚基的6个位点进行综合分析，研究小麦籽粒蛋白与品质性状间的关系，结果表明6个高分子量（HMW）和低分子量（LMW）麦谷蛋白位点对蛋白质含量的效应大小为，Glu-D1>Glu-B3>Glu-A1=Glu-B1> Glu-A3=Glu-D3；对GMP含量的效应大小为, Glu-A3>Glu-B3>Glu-D1> Glu-B1>Glu-A1>Glu-D3；对湿面筋含量的效应大小为, Glu-B1>Glu-B3= Glu-D3>Glu-A3>Glu-A1>Glu-D1；对Zeleny沉降值的效应大小为, Glu-A1> Glu-B3>Glu-D3>Glu-D1>Glu-B1>Glu-A3；对SDS沉降值的效应大小为, Glu-B3>Glu-A1=Glu-D1=Glu-A3>Glu-D3>Glu-B1。对蛋白含量而言，各位点的最佳组合方式为1、17+18、5+10、Glu-A3e、Glu-B3g、Glu-D3b；对湿面筋含量而言，各位点的最佳组合方式为1、6+8、5+10、Glu-A3d、Glu-B3c、Glu-D3b；对Zeleny沉降值而言，各位点的最佳组合方式为N、17+18、5+10、Glu-A3d、Glu-B3d、Glu-D3b；对SDS沉降值而言，各位点的最佳组合方式为1、7+8、2.2+12、Glu-A3b、Glu-B3g、Glu-D3b。另外，分析了稀有亚基对5+12与2.2+12与品质性状的关系，认为5+12对品质有负效应，2.2+12对品质有正效应。在品质育种时，应对优异组合或优异亚基加以利用。 3. 首次利用重组自交系（RILs）为材料，研究麦谷蛋白亚基表达量与品质性状的关系，通过对重组自交系中各HMW-GS表达量的分析，认为，就单个亚基的表达量而言，7亚基最高；其次为2亚基、5亚基、12亚基和10亚基；亚基9和1的表达量最小；N亚基不表达。对成对出现的亚基对而言，x型和y型亚基的总表达量2+12>5+10>7+9>17+18。就单个亚基与品质性状的关系而言，仅有10亚基的表达量与蛋白含量的相关性达5%的显著水平，2亚基的表达量与湿面筋含量呈负相关，显著水平也达5%，其余单个亚基对品质性状均无显著影响；就x型/y型亚基的比例来看，2/12和5/10对湿面筋含量都有显著的负效应；对某一位点等位基因控制的亚基表达总量来看，2+12对SDS沉降值有显著负效应。另外，本研究得出：2＋12的亚基对的负效应主要体现在2亚基上，且在同一位点上，x型亚基的表达量大于y型。所以推导稀有亚基组合2+10很可能也是劣质亚基。 4. 以 Glu-A1、Glu-B1、Glu-D1、Glu-B3和Glu-D3作为5个因素对99G45/京771和Pm97034/京771杂交后代的蛋白质含量和SDS沉降值进行多因素方差分析。结果表明，Glu-A1和Glu-D3对蛋白含量的加性效应达5％显著水平；Glu-D1 * Glu-D3对蛋白质含量的互作效应也达5%显著水平；其余位点的加性和互作效应对蛋白质含量的影响均不显著。对SDS 沉降值而言，Glu-D1的加性效应最大,贡献率为4.2 % ,达1 %显著水平,其次是Glu-B1位点,贡献率为3.3% ,达5%显著水平。其余位点对SDS 沉降值的加性和互作效应均未达5%显著水平。总体而言, 各位点对蛋白含量的效应大小为Glu-D3 > Glu-A1 > Glu-D1>Glu-B1>Glu-B3；对SDS沉降值的效应大小为Glu-D1>Glu-B1> Glu-D3>Glu-A1> Glu-B3。Glu-D1和Glu-D3位点上等位基因变异对蛋白含量有显著或极显著影响，含Glu-D1d和Glu-D3 GD、Glu-D3 JD基因的株系分别比含Glu-D1a和Glu-D3 PD基因的株系有较高的蛋白含量；在该遗传背景下，麦谷蛋白各基因位点对蛋白含量的效应大小依次排列为：Glu-A1位点1>N；Glu-B1位点7+9>17+18>14+15；Glu-D1位点5+10>2+12；Glu-B3位点GB>JB>PB；Glu-D3位点GB>JB>PB。对SDS沉降值的效应大小依次排列为：Glu-A1位点1>N；Glu-B1位点7+9=17+18>14+15；Glu-D1位点5+10>2+12；Glu-B3位点GB>JB>PB；Glu-D3位点GB>JB>PB。所以，对蛋白含量和SDS沉降值均较好的组合为1，7+9，5+10，GB，GD。 5. 因为GB和PB对品质的效应有显著差异，选取LMW-GS位点特异扩增引物对京771、99G45和Pm97034的Glu-B3位点进行扩增，结果得到三个不一样的扩增片段（Genebank号为DQ539657－DQ539659），得到的基因片段与Genebank中已报道的同类序列高度同源。通过克隆片段组成的分析，发现对Pm97034的序列较京771和99G45段少一个7氨基酸的重复单元，这可能是它较另外两个片段对面筋强度影响小的主要原因；另外，在99G45的序列中，124位处出现L（亮氨酸）代替P（脯氨酸），158位处出现了T（苏氨酸）代换M(蛋氨酸)，这可能是99G45Glu-B3位点序列对SDS沉降值的效应显著优于Pm97034的原因。 6．通过对RILs各位点同普通小麦品种（系）各位点与品质关系的比较，发现对SDS沉降值的效应，各位点在不同研究材料中是不同的，普通小麦中：Glu-B3>Glu-A1=Glu-D1=Glu-A3>Glu-D3>Glu-B1，RILs中：Glu-D1>Glu-B1> Glu-D3>Glu-A1> Glu-B3。利用重组自交系材料（完全排除了1BL/1RS易位干扰）所得到的结果与Gupta and MacRitchie (1994)所得结论一致。进一步证实了1BL/1RS易位对小麦品质的重要影响。对蛋白含量而言，普通小麦品种（系）中，Glu-D1>Glu-B3>Glu-A1=Glu-B1> Glu-A3=Glu-D3，RILs中，Glu-D3 > Glu-A1 > Glu-D1>Glu-B1>Glu-B3，和对SDS沉降值的效应一样，推断在非1BL/1RS易位的情况下，各位点对其效应应为Glu-D3 > Glu-A1 > Glu-D1>Glu-B1>Glu-B3。 对同一位点的等位基因而言，普通小麦和重组自交系中Glu-A1和Glu-D1上的等位基因对品质性状的贡献是一致的，但Glu-B1上的等位基因对SDS沉降值的贡献发生了变化，普通小麦中17+18>7+9，RILs中7+9>17+18，这可能也是1BL/1RS造成的。 Baking quality improved is one of the main object of wheat bread in China. The overall objective of the present studies was to increase the understanding about protein quality in wheat, i.e. to make it possible to improve the production of wheat with desired quality for different end-uses. With the analysis of gluten protein in RILs, 99G45/Jing 771 and Pm97034/Jing, and 228 wheat cultivars or lines in China, the correlations between glutenin compositions and protein content, glutenin macropolymer(GMP), wet gluten content, Zeleny sedimentation value and SDS sedimentation value contentand breadmaking quality were studied. Also a rapid and efficient detection method of geneticpolymorphism at Glu-B3 loci in wheat was established using polymerase chain reaction(PCR).The results obtained were as follows: 1. Cultivated Chinese wheat germplasm has been a valuable genetic resource in international plant breeding. Patterns of gliadin among cultivated Chinese accessions are unknown, despite the proven value and potential novelty. The objective of this work was to analyse the diversity within improved Chinese wheat germplasm. The electrophoretic banding patterns of gliadin in common wheat cultivars and advanced lines were determined by acid-polyacrylamide gel electrophoresis. For 148 leading commercial cultivars and promising advanced lines used in our study, 48 patterns were identified, 29 corresponding to ω-gliadin, 9 to γ-gliadin, 5 to β-gliadin and 5 to α-gliadin. The most frequent patterns were A6 in ω; B in γ; B in β and A in the region of α. 116 band types appeared in the148 samples: 94 accessions had unique gliadin types, and 22 gliadin types while not unique were found in 54 accessions. The gliadin patterns of Chinese wheat cultivars and lines greatly differed from the patterns of wheat lines from other countries. Three patterns, E, J, H, M, N and O in the ω-zone had not previously been reported. Three wheat zones，the Northern Winter Wheat Region, the Yellow and Huai Valley River valleys Winter Wheat Region and the Southwestern Winter Wheat Region，in China showed different frequencies in their gliadin patterns. This information can be used to monitor genetic diversity with Chinese wheat germplasm. 2. To analyse the relationship between the loci and characteristics quality, we utilized the 228 cultivars/lines. The results showed that : For protein content, Glu-D1 >Glu-B3>Glu-A1=Glu-B1>Glu-A3=Glu-D3. For GMP content, Glu-A3>Glu-B3 >Glu-D1>Glu-B1>Glu-A1>Glu-D3. For wet gluten content, Glu-B1>Glu-B3= Glu-D3>Glu-A3>Glu-A1>Glu-D1. For Zeleny sedimentation value, Glu-A1>Glu-B3> Glu-D3>Glu-D1>Glu-B1>Glu-A3, For SDS sedimentation value, Glu-B3>Glu-A1= Glu-D1= lu-A3>Glu-D3>Glu-B1。For protein content, the best combination of 6 loci is (1,17+18,5+10,Glu-A3e, Glu-B3g,Glu-D3b). For wet gluten content, the best combination of 6 loci is (1,6+8,5+10,Glu-A3d,Glu-B3c,Glu-D3b). For Zeleny sedimentation value, the best combination of 6 loci is (N,17+18,5+10,Glu-A3d, Glu-B3d, Glu-D3b). For SDS sedimentation value, the best combination of 6 loci is(7+8,2.2+12,Glu-A3b, Glu-B3g,Glu-D3b)。Additional, we analysed the relationship between the subunits 5+12 and 2.2+12, think that 5+12 was negative for quality, 2.2+12 is postive for quality. It should be effective utilized. 3. It’s the first time to utilize RILs to study the relationship between subunits expression quantity and characteristics quality. The results showed that: For single subunit, the expression quantity of 7 is the highest. Then the 2, 5, 12 and 10. The expression of subunit 9 and 1 is the lowest. Subunit N is not expressed. For subunits, the expression quantity of x type and y type are 2+12>5+10>7+9>17+18. The significant relation of 5% only showed between the expression quantity of subunit 10 and protein content. The relationship between expression quantity of others and characteristic quality was not significant. For x type/ytype, 2/12 and 5/10 is negative relation insignificant level. For the subunit(s) in a loci, Only 2+12 effect SDS sedimentation value negative in significant level. 4. With RILs 99G45/Jing 771 and Pm97034/Jing 771, we found that: The effective of Glu-A1, Glu-D3 and Glu-D1 * Glu-D3 for protein content is significant at 5% level. The effect of other loci for protein wre not significant. For SDS sedimentation value, the effect of Glu-D1is the highest, which contribution is 4.2 % .Then the Glu-B1, contribution is 3.3%. The effect of other loci for SDS sedimentationvalue were not significant. In total, for protein content: Glu-D3 > Glu-A1 > Glu-D1>Glu-B1>Glu-B3; for SDS sedimentationvalue: Glu-D1>Glu-B1> Glu-D3>Glu-A1>Glu-B3. The effect of alleles in Glu-D1 and Glu-D3 loci are significant at 1% or 5%. In Glu-A1, 1>N; Glu-B1, 7+9>17+18>14+15; Glu-D, 5+10>2+12; Glu-B3, GB>JB>PB; Glu-D3, GB>JB>PB. For SDS sedimentation, Glu-A1, 1>N; Glu-B1, 7+9=17+18>14+15; Glu-D1, 5+10>2+12; Glu-B3, GB>JB>PB; Glu-D3, GB>JB>PB. The best combinations for SDS sedimentation value is 1，7+9，5+10，GB，GD. 5. Because of the difference of GB and PB for SDS sedimentation value, we selected the specific primer for LMW-GS loci to amplified the Glu-B3 of Jing771, 99G45and Pm97034. We got 3 amplify fragment (Gene Bank accession number are DQ539657－DQ539659）. We found that the fragment of Pm97034 were deleted a repetitive 7 amino acid domain, which is perhaps the reason effect the gluten strength. Furthermore, in the position 124 of sequence 99G45, L has been replaced with P. Position 158, T replaced M, which may be the reason why the Glu-B3 locus of 99G45 is prefer to Pm97034 when refer to SDS sedimentation value. 6. Comparing the results of RILs and common wheat, we found that perhaps just the1BL/1RS made the difference of loci in different accession.

功能菌剂的混合发酵研究

随着化工行业的发展，大量有毒有害难降解有机物随工业废水的排放进入环境，这些物质能够在环境中长期存在、积累和扩散，通过食物链对动植物的生存及人类的健康造成不良影响。本文以苯酚、对氯硝基苯、氯苯和十六烷为模拟污染物，以前期研制的功能菌剂为对象，经过紫外线线诱变筛选出优于出发菌株的功能菌，对诱变后功能菌的理化性能进行了研究，对菌种进行了鉴定，在此基础上，就其相互之间的微生态关系进行研究，为混合发酵提供理论基础，并就其最佳发酵条件及发酵参数进行了研究，最后对发酵产品的性能进行了检测。目前，国内外有关功能菌剂的研究还存在多方面的不足，主要包括：①由于多菌种混合发酵过程较为复杂，各菌之间存在复杂的相互作用，影响因素较多，关于菌种之间的相互关系研究得很少，环境功能菌剂的发酵方法大多采用单独发酵后混合的方式。单独发酵对原材料、设备和能源的利用率较低，对于多菌种制剂发酵，在设备、能源和原材料的方面造成的浪费更大，将会大幅增加菌剂的生产成本，影响多菌种功能菌剂的发展；②功能菌剂生产过程的质量控制方面研究得较少；③功能菌剂产品的稳定性、抗冲击性能研究得较少，对环境微生物制剂的研究主要集中在菌种选育和培养条件优化方面。 通过本论文研究，得到以下主要结论。 （1）在紫外线诱变处理中，用紫外线对发生一定程度退化的出发菌株进行诱变处理后，六株具有高效降解性能的菌株被筛选出来，诱变筛选出的菌株形态和ERIC-PCR指纹图谱与出发菌株相比发生了明显改变；而且诱变后的菌株对目标难降解底物的降解能力均得到改善，其中，FPN、FCB、F14、FEm对目标底物的降解率提高了20%以上；诱变后菌株经过7次连续传代接种后，对目标难降解底物的降解率无显著变化，具有一定的遗传稳定性。并对诱变后的功能菌进行了初步的鉴定，这6株菌都分别是芽孢杆菌。 （2）对诱变后的功能菌相互之间的微生态关系进行了研究，通过抑菌实验、生长量以及基质消耗量的比较，确定它们之间的生长关系是无害共栖关系，可以进行混合发酵。 （3）对该功能菌剂进行发酵培养条件研究，结果表明发酵培养基的最佳成分（g/L）：葡萄糖 31.0g/L、玉米粉10.0g/L、磷酸氢二钾1.0g/L、硫酸铵1.1g/L、硫酸镁0.55g/L。通过研究不同的培养条件对菌体生长和降解性能的影响，确定了最佳培养条件：培养基初始pH7.5；最适温度32℃；培养基装液量125mL（250 mL三角瓶），以及培养时间对降解性能的影响，培养20 h的产物对降解最为有利。通过研究添加不同目标污染物对菌体生长和降解性能的影响，确定了添加目标污染物的最佳量以及最佳时间：苯酚投加量：1.125 g/L，对氯硝基苯投加量：0.1 g/L；最佳投加时间为发酵培养开始后4 h。 （4）以摇瓶分批发酵最优条件为基础，对FPN、F10、FCB、FNa、F14 和 FEm进行了摇瓶分批发酵试验。以摇瓶分批发酵试验数据为依据，对功能菌剂分批发酵动力学进行了研究，建立了菌体生长和基质消耗的动力学模型，拟合模型能较好的反映功能菌剂分批发酵过程。 （5）功能菌剂和活性污泥协同作用，可以提高系统的生物降解能力，功能菌剂投加量为2%，新鲜活性污泥3500 mg/L，降解24 h条件下，功能菌剂和活性污泥的协同作用对COD的去除率和对照组相比，最多的提高了36.8%。功能菌剂和活性污泥协同作用以及活性污泥的单独作用，其生物降解过程均符合一级反应动力学过程，功能菌剂和活性污泥协同作用的生物降解动力学方程为：，相关系数97%。采用SBR运行方式，引入功能菌剂的SBR系统明显能够改善和提高生物降解的效率。与仅有活性污泥的系统相比，系统对COD的平均去除率可以提高27.1%，同时，系统的耐负荷冲击以及耐毒害冲击的性能比仅有活性污泥的SBR系统强，特别是负荷冲击对引入功能菌剂的SBR系统影响很小。仅有活性污泥的SBR系统经过负荷冲击和毒害冲击之后，不能恢复到冲击之前的水平，而且系统有效作用时间的周期比引入功能菌剂的SBR系统相比大大缩短，而引入功能菌剂的SBR系统处理效果较为稳定，恢复能力很强。 Along with the development of industries, many recalcitrant organic chemicals have been discharged into natural environments together with wastewaters and can exist in waters, soil and sediments for a long time without degradation. These haz-ardous substances, their byporducts and metabolizabilities can be highly toxic, mu-tagenic and carcinogenic, thereby threatening animals, plants and human health through food chain. Consequently the removal of these compounds is of significant interest in the area of wastewater treatment. In this dissertation, the phenol, hydro-quinone, chlorobenzene and hexadecane treated as the model pollutants, the func-tional microorganism agent was used as the starting strains, they treated with ultra-violet light, and then the mutant strains with high degradation ability were screened out and identified primarily, the relationship between these stains were studied, the medium composition and fermentation conditions were optimized, the degradation ability of the fermented production was tested. The literature survey indicates that the study of the microorganism agent is far from complete and more information is re-quired on following problems. 1, Because of the complexity of relationship in mixed fermentation and the complicated factors, the study is hardly to process.2, There is a lack of information on the quality control of the producing process .3, And there is a lack of information on the stability about the microorganism agent. In this dissertation, the main results of the present study could be summarized as follows: (1)The degenerate starting strains were treated with the ultraviolet light, and six mutant strains with high biodegradation ability were screened out by using the me-dium with selective pressure of model pollutants. The mutant strains had great changes in colonialmorphology and ERIC-PCR fingerprinting. And the mutant strains got obvious advantages over the starting strains in degradation ability and over 20% improvement of removal rates was achieved for FPN、FCB、F14 and FEm. The de-gradation ability of the mutant strains was stable after seven generations. After that, the mutant strains were primarily identified as bacillus respectively. (2) The relationship between these mutant strains was studied. By the compari-son of antibiosis effect, biomass and consumption of substrate, the relationships were neutralism and they could be mixed fermented. (3) The optimized cultivation conditions were as follows: glucose 31.0 g/L, corn power 10 g/L, K2HPO4 1.0 g/L, (NH4)2SO4 1.1 g/L, MgSO4 0.55 g/L, initial pH7.5, temperature 32℃, working volume 125 mL/250 mL, and cultivation time 20h (con-sidering the time effect on degradation ability), adding pollutants phenol (1.125 g/L) and hydroquinone (0.1 g/L) into the broth at 4 h after cultivation. (4) Based on the above optimum condition, the batch fermentation was per-formed with strains FPN, F10, FCB, FNa, F14 and FEm in shake flask. The batch fermentation kinetics was studied based on the experimental data. Two kinetic models were constructed which could reflect the regularity of growth and substrate consump-tion in the process of batch fermentation. (5) The co-operation of functional microorganism agent and activated sludge could raise biodegradation of system by adding some microorganism agent and 3500 mg/L fresh activated sludge. Bioaugumentation by the addition of high effective deg-radation culture enhanced the treatment effect of SBR system and the COD removal rate was increased by 20%-36.8%. Its biodegradation matched first-order dynamical reaction equation, and the reaction equation was ln0.2327.391ct=−+. The micro-organism agent had the effect of optimization to activated sludge micro-ecosystem. The SBR system adding 2% microorganism agent, the average COD removal rate of that was increased by 27.1% and stronger anti-shock ability to load and toxicant were achieved (compared with SBR system just adding activated sludge). Especially the load-shock has barely effect to the SBR system adding microorganism agent. After the load and toxicant shock, the SBR system just adding activated sludge couldn’t come back to original level and the activated sludge micro-ecosystem was frustrated. The applying of microorganism agent increased biological activity and system’s re-sistance ability to load shock and toxicant shock.