(Ba3MTiMO9)-Ti-III-O-V (M-III = Fe, Ga, Y, Lu, M-V = Nb, Ta, Sb) perovskite oxides Synthesis, structure and dielectric properties

We describe the synthesis structures and dielectric properties of new perovskite oxides of the formula (Ba3MTiMO9)-Ti-III-O-V for M-III = Fe Ga Y Lu and M-V = Nb Ta Sb While M-V = Nb and Ta oxides adopt disordered/partially ordered 3C perovskite structures where M-III/Ti/M-V metal-oxygen octahedra are corner connected the M-V = Sb oxides show a distinct preference for the 6H structure where Sb-V/Ti-IV metal-oxygen octahedra share a common face forming (Sb Ti)O-9 dimers that are corner-connected to the (MO6)-O-III octahedra The preference of antimony oxides (Sb-V 4d(10)) for the 6H structure which arises from a special Sb-V-O chemical bonding that tends to avoid linear Sb-O-Sb linkages unlike Nb-V/Ta-V d(0) atoms which prefer similar to 180 degrees Nb/Ta-O-Nb/Ta linkages - is consistent with the crystal chemistry of M-V-O oxides in general The dielectric properties reveal a significant difference among Mill members All the oxides with the 3C structure excepting those with Mill = Fe show a normal low loss dielectric behaviour with epsilon = 20-60 in the temperature range 50-400 degrees C the M-III = Fe members with this structure (M-V = Nb Ta) display a relaxor-like ferroelectric behaviour with large E values at frequencies <= 1 MHz (50-500 degrees C) (C) 2010 Elsevier Masson SAS All rights reserved

Grinding abrasive wear and associated particle size effect

The type of abrasion that the grinding medium experiences inside a ball mill is classified as high stress or grinding abrasion, because the stress levels at the surface of the medium exceed the yield stress of the metal when hard abrasives are crushed. During dry grinding of ores the medium undergoes not only abrasion but also erosion and impact. As all three mechanisms of wear occur simultaneously, it is difficult to follow the individual components of wear. However, it is possible to show that the overall kinetics of wear follows a simple power law of the type w = at(b), where w is the weight loss of the grinding medium for a specified grinding time t and a and b are constants. Experimental data, obtained from dry grinding of quartz for a wide range of times using AISI 52100 steel balls having various microstructures in a laboratory scale batch mill, are fitted to the proposed equation and the wear rate w is calculated from the first derivative of the equation. The mean particle sizes of the quartz charge DBAR corresponding to 50 and 80% retained size are determined by mechanical sieving of the ground product after a grinding time t and thus the relationship between wear rate and particle size of the abrasive is established. It is found that w increases rapidly with DBAR up to some critical size and then increases at a much lower rate.

Ball wear mechanisms and control in the grinding of sulfide and phosphate ores

Marked ball grinding tests were carried out in the laboratory using high carbon low alloy steel (cast and forged) and high chrome cast iron balls. Relative ball wear as a function of grinding period and milling conditions was evaluated for the different type of ball materials in the grinding of lead-zinc sulphide and phosphate ores. Results indicated that ball wear increased with time and showed a sharp increase for wet grinding over dry grinding. Ball wear under wet grinding conditions was also influenced by the gaseous atmosphere in the mill. The influence of oxygen on the corrosive wear of grinding balls was increasingly felt in case of sulphide ore grinding. The grinding ball materials could be arranged in the following order with respect to their overall wear resistance:

Laboratory studies on ball wear in the grinding of a chalcopyrite ore

Wear of high carbon low alloy (HCLA) cast steel balls during the grinding of a chalcopyrite ore was evaluated under different experimental conditions. The role of oxygen in enhancing ball wear during wet finding is brought out. The influence of pH on ball wear was also examined from the view point of acid production during grinding and reactivity of sulphides. Contributions from corrosion and abrasion towards ball wear are quantified in terms of ball wear rates as a function of time, particle size and gaseous atmosphere in the mill.

Solid state amorphization in binary Ti---Ni, Ti---Cu and ternary Ti---Ni---Cu system by mechanical alloying

An amorphous phase has been synthesized by mechanical alloying in a planetary mill over a nickel content range of 10�70 at.% in the Ti---Ni system and a copper content range of 10�50 at.% in the Ti---Cu system. In the case of ternary Ti---Ni---Cu alloys the glass-forming composition range has been found to be given by x = 10�20 for Ti60Ni40 ? xCux, x = 10 � 30 for Ti50Ni50 ? xCux and x = 10 � 40 for Ti40Ni60 ? xCux alloys. The difficulty in the amorphization of copper-rich compositions is explained in the light of enthalpy composition diagrams calculated for the ternary solid solution and the amorphous phase.

Studies on grinding media wear and its effect on flotation of ferrugenous phosphate ore

Marked ball grinding rests were carried out in the laboratory with a low grade phosphate ore under different experimental conditions. Two types of balls were used, namely high carbon low alloy (HCLA) cast steel and high chrome cast iron. Results of marked ball grinding tests indicated that ball wear increased with time and showed a sharp increase for wet grinding over dry grinding. Ball wear under wet grinding conditions was also influenced by the gaseous atmosphere in the mill. The grinding ball materials could be arranged in the following order with respect to their overall wear resistance: High chrome cast iron > HCLA cast steel balls Methods to minimize ball wear through control of mill atmosphere and addition of flotation reagents are discussed. Effect of grinding media and additions of flotation reagents during grinding on phosphate ore flotation are also discussed. (C) 1999 Elsevier Science Ltd. All rights reserved.

Mechanochemical decomposition of Gd3Fe5O12 garnet phase

Gadolinium iron garnet was milled in a high energy ball mill to study its magnetic properties in the nanocrystalline regime. XRD reveals the decomposition of the garnet phase into Gd-orthoferrite and Gd2O3 on milling. The variation of saturation magnetization and coercivity with milling is attributed to a possible shift in the compensation temperature on grain size reduction and an increase in the orthoferrite content. The Mössbauer spectrum at 16 K is characteristic of the magnetically ordered state corresponding to GdIG, GdFeO3 and α-Fe2O3 whereas at room temperature it is a superparamagnetic doublet.

Herbal medicines used in the treatment of diabetes mellitus in Arunachal Himalaya, northeast, India

Ethnopharmacological relevance: Medicinal plants have played an important role in treating and preventing a variety of diseases throughout the world. Khampti tribal people living in the far-flung Lohit district of the Eastern Arunachal Himalaya, India still depend on medicinal plants and most of them have a general knowledge of medicinal plants which are used for treating a variety of ailments. This survey was undertaken in Lohit district in order to inventory the medicinal plants used in folk medicine to treat diabetes mellitus. Materials and methods: Field investigations were conducted in seventeen remote villages of Lohit district starting from April 2002 to May 2004 through interviews among 251 key informants who were selected randomly during our household survey. To elucidate community domains and determine differences in indigenous traditional knowledge of medicinal plants with anti-diabetic efficacy, we repeated our field survey starting from April 2008 to May 2010 with one hundred traditional healers locally called as ``Chau ya'' in Khampti of Lohit district. ``Chau ya'' traditional healers who know and use medicinal plants for treating diabetes mellitus were interviewed using a semi-structured questionnaire. Results: This study reports an ethnobotanical survey of medicinal plants in Lohit district of Arunachal Pradesh reputed for the treatment of diabetes mellitus. Forty-six plant species were identified in the study area to treat diabetes mellitus by the Khamptis ``Chau ya'' traditional healers. Comparative published literature survey analysis of this study with other ethnobotanical surveys of plants used traditionally in treating diabetes mellitus suggests that eleven plant species make claims of new reports on antidiabetic efficacy. These plant species are Begonia roxburghii, Calamus tenuis, Callicarpa arborea, Cuscuta reflexa, Dillenia indica, Diplazium esculentum, Lectuca gracilis, Millingtonia hortensis, Oxalis griffithii, Saccharum spontaneum, and Solanum viarum. Some of the plants reported in this study have an antidiabetic effect on rodent models but none have sufficient clinical evidence of effectiveness. Conclusions: The wide variety of medicinal plants that are used to treat diabetes mellitus in this area supports the importance of plants in the primary healthcare system of the rural people of Lohit district of Arunachal Pradesh. The finding of new plant uses in the current study reveals the importance of the documentation of such ethnobotanical knowledge. (C) 2012 Elsevier Ireland Ltd. All rights reserved.

Synthesis of pure iron magnetic nanoparticles in large quantity

Free nanoparticles of iron (Fe) and their colloids with high saturation magnetization are in demand for medical and microfluidic applications. However, the oxide layer that forms during processing has made such synthesis a formidable challenge. Lowering the synthesis temperature decreases rate of oxidation and hence provides a new way of producing pure metallic nanoparticles prone to oxidation in bulk amount (large quantity). In this paper we have proposed a methodology that is designed with the knowledge of thermodynamic imperatives of oxidation to obtain almost oxygen-free iron nanoparticles, with or without any organic capping by controlled milling at low temperatures in a specially designed high-energy ball mill with the possibility of bulk production. The particles can be ultrasonicated to produce colloids and can be bio-capped to produce transparent solution. The magnetic properties of these nanoparticles confirm their superiority for possible biomedical and other applications.

Biodegradation of acrylamide and purification of acrylamidase from newly isolated bacterium Moraxella osloensis MSU11

The increasing industrial utilization of polyacrylamide to assist water clarification, sludge conditioning, papermaking, and secondary oil recovery leads to environmental pollution. In this work, an acrylamide degrading bacterium was isolated from paper mill effluent at Charan mahadevi, Tamilnadu, India. The minimal medium containing acrylamide (40 mM) served as a sole source of carbon and nitrogen for acrylamide degrading bacteria. The bacterial strain has grown well in 40 mM acrylamide at pH (6-7) at 30 degrees C. Within 24-48 h acrylamide was converted into acrylic acid and other metabolites. Based on biochemical characteristics and 16S rRNA gene sequence, the bacterial strain was identified as Gram negative, diplobacilli Moraxella osloensis MSU11. The acrylamide hydrolyzing bacterial enzyme acrylamidase was purified by HPLC. The enzyme molecular weight was determined to be approximately 38 kDa by SDS-PAGE using reference enzyme Pectinase. These results show that M. osloensis MSU11 has a potential to degrade the acrylamide present in the environment. (C) 2013 Elsevier Ltd. All rights reserved.

Effect of Manganese (II) Oxide on microstructure and ionic transport properties of nanostructured cubic zirconia

Effect of MnO addition on microstructure and ionic transport properties of nanocrystalline cubic(c)-ZrO2 is reported. Monoclinic (m) ZrO2 powders with 10-30 mol% MnO powder are mechanically alloyed in a planetary ball mill at room temperature for 10 h and annealed at 550 degrees C for 6 h. In all compositions m-ZrO2 transforms completely to nanocrystalline c-ZrO2 phase and MnO is fully incorporated into c-ZrO2 lattice. Rietveld's refinement technique is employed for detailed microstructure analysis by analyzing XRD patterns. High resolution transmission electron microscopy (HRTEM) analysis confirms the complete formation of c-ZrO2 phase. Presence of stoichiometric Mn in c-ZrO2 powder is confirmed by Electron Probe Microscopy analysis. XPS analysis reveals that Mn is mostly in Mn2+ oxidation state. A correlation between lattice parameter and oxygen vacancy is established. A detailed ionic conductivity measurement in the 250 degrees-575 degrees C temperature range describes the effect of MnO on conductivity of c-ZrO2. The ionic conductivity (s) of 30 mol% MnO alloyed ZrO2 at 550 degrees C is 0.04 s cm(-1). Electrical relaxation studies are carried out by impedance and modulus spectroscopy. Relaxation frequency is found to increase with temperature and MnO mol fraction. Electrical characterization predicts that these compounds have potentials for use as solid oxide fuel cell electrolyte material. (C) 2015 Elsevier Ltd. All rights reserved.

Stabilization of the high-temperature and high-pressure cubic phase of ZnO by temperature-controlled milling

The reversible transition of wurtzite to rock salt phase under pressure is well reported in literature. The cubic phase is unstable under ambient conditions both in the bulk and in nanoparticles. This paper reports defect-induced stabilization of cubic ZnO phase in sub 20 nm ZnO particles and explores their optical properties. The size reduction was achieved by ball milling in a specially designed mill which allows a control of the milling temperature. The process of synthesis involved both variation of milling temperature (including low temperature similar to 150 K) and impact pressure. We show that these have profound influence in the introduction of defects and stabilization of the cubic phase. A molecular dynamics simulation is presented to explain the observed results. The measured optical properties have further supported the observations of defect-induced stabilization of cubic ZnO and reduction in particle size.

Efecto de labranza y métodos de control de malezas sobre factores biológicos presentes en agro-ecosistemas de frijol común (Phaseolus vulgaris L.) postrera 1995

Durante la postrera de 1995, se estableció el experimento de campo en la finca experimental La Compañía, localizada en San Marcos, Carazo, con el propósito de evaluar los efectos de tres tipos de labranza y métodos de control de malezas sobre la dinámica de las malezas, plagas, enfermedades y enemigos naturales en el cultivo de frijol común, de igual forma conocer el efecto de los factores en estudio sobre el rendimiento del frijol común (Phaseolus vulgaris L.). Los tratamientos en estudio se evaluaron en un diseño de bloques completamente al azar con arreglo de parcelas divididas con cuatro repeticiones. Los factores en estudio fueron A: sistemas de labranza (labranza cero, labranza mínima y labranza convencional) y B: controles de malezas (pre-emergente más post-emergente, pre-emergente más chapia, y pre-emergente más cobertura muerta de maiz (Zea mays L.). Los resultados indican que las especies de malezas dominantes fueron plantas de la familia Cyperaceae, sobresaliendo Cyperus rotundus L.y de la familia Poaceae: Digitaria sanguinalis (L). Scop, Ixophorus unisetus (Presl) Schlech,. De la clase dicotiledónea se identificaron Melantera aspera (Jacquin) de la familia Asteraceae, Argemone mexicana L. de la familia Papaveraceae; y Chamaesyce hirta (L.) Mill de la familia Euphorbiaceae. Las especies descritas anteriormente fueron las de mayor abundancia y dominancia (cobertura y peso seco) en el área del experimento donde los mejores resultados se presentaron en labranza mínima y manejo pre emergente más post emergente. Referente a plagas, se encontró que labranza mínima presentó mayor número de especies de plagas de suelo. En cuanto a insectos plagas de follaje, los mas importantes que se presentaron en el ensayo están Diabrótica spp.; Nodonata spp. y Empoasca spp.; predominando entre todos. Diabrótica spp. quien estuvo presente hasta la madurez fisiológica del cultivo. De los tres sistemas de labranza, labranza cero fue la que mejor disminuyó las poblaciones de insectos plagas. En los controles de maleza, el control pre-emergente más cobertura permitió mayor población de insectos plagas. La mayor cantidad de benéficos se observó en labranza convencional, en los controles de malezas, la mayor cantidad de insectos benéficos se obtuvo en el tratamiento pre-emergente más post-emergente. En cuanto a la incidencia y severidad de las enfermedades el mayor valor se obtuvo en labranza convencional. Los mejores resultados se obtuvieron en labranza cero y mínima. La incidencia de enfermedades fue mayor usando control pre-emergente más chapia y resultó menor con control pre-emergente más cobertura. El mayor rendimiento de grano se obtuvo en labranza minima. En cuanto a los controles de malezas se obtuvieron mayores rendimiento en el control pre-emergente mas chapia

Análisis de riesgo de plagas de importancia fitosanitaria para Nicaragua en la importación de semilla de cebolla (Allium cepa L.) procecedente de Canadá

El presente Análisis de riesgo de Plagas (ARP) se realizó en el Centro Nacional de Diagnóstico Fitosanitario (CNDF) y Cuarentena del MAG-FOR en Managua, Nicaragua, e1 cual tuvo por objetivo evaluar el riesgo de introducción, establecimiento y dispersión de plagas de importancia fitosanitaria para Nicaragua en semilla de cebolla (Allium cepa L.) importada de Canadá, así como determinar las medidas adecuadas de protección fitosanitarias para evitar la introducción de las mismas a Nicaragua. De un listado inicial de 18 plagas, sólo 6 plagas son sujetas a evaluación y manejo del riesgo después de pasar por las tres etapas de evaluación de un ARP según la Norma Centroamericana del OIRSA, por considerarse que estas presentan capacidad biológica y de comportamiento, así como rangos óptimos de temperaturas que se asemejan a las condiciones de clima de las zonas productoras de Allium cepa L. del país. (Anexo1). El cuadro 1 contiene la lista de las plagas no sujetas a Evaluación del Riesgo Puccinia allii ( DC) Rudolphi y Urocistis Cepulae. Frost que causan la Roya y el carbón de la cebolla respectivamente son consideradas plagas específicas de los cultivos del género Allium P. allí es considerada plaga de bajo riesgo de introducción al país siendo la limitante para su establecimiento que su óptimo de temperatura ( 1 O" a 15" C), no se asemeja a las condiciones de temperatura de las zonas productoras del país( Anexo l ), mientras que U. cepulae es considerado como un hongo muy peligroso capaz de provocar pérdidas en la producción de hasta 80 por ciento tiene alta probabilidad de establecimiento v diseminación en las zonas productoras del país va que las condiciones de edafoclímaticas (16-22" C y pH 5-8) le favorecen( Anexo 1) Botryotinia squamosa. Viennot-Bourgín es un hongo que causa la pudrición blanda de la cebolla, se considera una plaga especifica de cultivos del género Allium con probabilidad alta de establecimiento v disemmac1ón en las zonas productoras de cebolla del país ya que el rango superior óptimo de temperatura (23" C) se asemeja a las condiciones de temperatura de las mismas (Anexo 11. Sclerotium cepivorum. Berkeley (1841 ). Es un hongo que causa la pudrición blanca de la cebolla y es considerado una plaga general de corto rango de hospedero quien además de atacar a cultivos del género Allium ataca también a lycopersicum esculentum (tomate) puede causar pérdidas en la producción de hasta un 70 por ciento (promedio) Y, con riesgo Alto de establecimiento en el país ya que temperaturas de 1 0"-20" C y baja humedad 40%. (pariona et. al) inclusive 30"- 5"C cuando hay humedad (Agrios 1985) y pH desde 1.4 a 8.8 le favorecen y las condiciones edafoclimáticas de las zonas productoras de cebolla del país se asemejan (Anexo ll). El nemátodo Ditylenchus dipsaci es un endoparásito destructor, y es considerado plaga general de cultivos del género Allium que ataca otros cultivos como cucurbitáceas. Zea mays (Maíz), Solanum tuberosum (Papa) y Nicotiana Tabacum (Tabaco). Es capaz de reducir la producción hasta un 75 por ciento (promedio) y la probabilidad de ingreso al país es media, a pesar de que su óptimo de temperatura (15º C) no se asemejan a la temperatura de las zonas productoras de cebolla del país. se considera de gran importancia sus características como: gran capacidad reproductiva es endoparásito y podemos encontrarlo dentro de cualquier parte de la planta inclusive dentro de la semilla. Aphelenchoides fragariae es un nematodo que tiene por hospedero secundario a Allium cepa. L puede ser capaz de ocasionar pérdidas en la producción de hasta 66.5% (promedio), es considerado plaga general de cultivos del género Allium con baja probabilidad de ingreso al país, va que su hospedero primario es la fresa y no se reportan daños en cebolla (no preferencia por Allium cepa L que es hospedero secundario) Todas estas plagas son consideradas de categoría A 1 1 para Nicaragua (no presentes en el país), lo que justifica plenamente la realización de este ARP a fin de tomar las medidas pertinentes que acompañen la importación de semilla y así evitar la introducción de nuevas plagas de difícil control.

Variabilidad molecular en una población de lotus tenuis tolerante a la salinidad

Resumen: Lotus tenuis Waldst et Kit (ex Lotus glaber Mill) (2n=2x=12), es una leguminosa perenne, utilizada como forrajera, que se introdujo en suelos salinoalcalinos de la Pampa Deprimida de la Provincia de Buenos Aires. L. tenuis presenta variabilidad genética para caracteres asociados a la tolerancia a salinidad que esta siendo explorada y explotada en programas de mejoramiento. El estudio de la variabilidad molecular en esta especie permitirá ayudar a los programas de mejoramiento a incrementar la adaptación de la especie en la Pampa Deprimida, permitiendo identificar poblaciones aptas para lograr alta productividad en los suelos salinos de la región. Mediante este trabajo se buscó cuantificar la variabilidad molecular de una población de L. tenuis tolerante a alta salinidad, para lo cual se extrajo ADN de 23 plantas y se utilizaron 8 marcadores ISSRs (Inter Secuencias Simples Repetidas) con la técnica de PCR (Reacción en Cadena de la Polimerasa). Con el uso de los programas de análisis molecular Structure (Pritchard et al., 2000), PowerMarker (Liu et al., 2005) y Arlequín (Excoffier et al., 2010), se estimó la estructura genética, varianza, medidas de diversidad y de distancia genética. A su vez se realizó a modo de complemento una comparación entre la población tolerante y otra población de L. tenuis susceptible a salinidad, para estimar la variabilidad genética entre poblaciones e identificar bandas especificas asociadas a la tolerancia a salinidad. El número obtenido de bandas presentes en la población tolerante fue de 73, que permitió realizar un estudio de la variabilidad molecular. La estructura genética representada por Structurama y Structure arrojó un K=1, observándose a las 23 plantas tolerantes agrupadas en una misma población. El uso de los 8 marcadores seleccionados permitieron estudiar la variabilidad molecular y la estructura genética de las poblaciones de L. tenuis, identificándose un total de 117 bandas totales. El análisis de la estructura poblacional reveló la existencia de una mayor homogeneidad en los individuos de la población tolerante que en la población susceptible. Los marcadores ISSRs desarrollados en este trabajo podrán ser utilizados en otros programas de mejoramiento genético de L. tenuis, para evaluar la variabilidad molecular presente en otras poblaciones de la especie