Change in the effect of constant photoperiods on the rate of sexual maturation in modern genotypes of domestic pullet

1. Data for modern egg-type hybrids reared on constant daylengths show that, as expected, they mature more quickly than earlier genotypes. However, the constant photoperiod which gives earliest sexual maturity has not changed as a result of selection and is 10 h for both early and modern genotypes. 2. Further analysis showed that the rate of delay in sexual maturity for constant photoperiods above 10 h is similar for modern and for early hybrids ( +0.29 d for each incremental one hour of photoperiod), the response of modern hybrids below 10 h ( +4.22 d for each one-hour reduction in photoperiod) is more than double that of early hybrids ( +1.71 d/h).

Modern approaches to floristics and their impact on the region of SW Asia

Attitudes to floristics have changed considerably during the past few decades as a result of increasing and often more focused consumer demands, heightened awareness of the threats to biodiversity, information flow and overload, and the application of electronic and web-based techniques to information handling and processing. This paper will examine these concerns in relation to our floristic knowledge and needs in the region of SW Asia. Particular reference will be made to the experience gained from the Euro+Med PlantBase project for the preparation of an electronic plant-information system for Europe and the Mediterranean, with a single core list of accepted plant names and synonyms, based on consensus taxonomy agreed by a specialist network. The many challenges Ð scientific, technical and organisational Ð that it has presented will be discussed as well as the problems of handling nontaxonomic information from fields such as conservation, karyology, biosystematics and mapping. The question of regional cooperation and the sharing of efforts and resources will also be raised and attention drawn to the recent planning workshop held in Rabat (May 2002) for establishing a technical cooperation network for taxonomic capacity building in North Africa as a possible model for the SW Asia region.

Modelling metal cutting using modern ductile fracture mechanics: Quantitative explanations for some longstanding problems

The assumption that negligible work is involved in the formation of new surfaces in the machining of ductile metals, is re-examined in the light of both current Finite Element Method (FEM) simulations of cutting and modern ductile fracture mechanics. The work associated with separation criteria in FEM models is shown to be in the kJ/m2 range rather than the few J/m2 of the surface energy (surface tension) employed by Shaw in his pioneering study of 1954 following which consideration of surface work has been omitted from analyses of metal cutting. The much greater values of surface specific work are not surprising in terms of ductile fracture mechanics where kJ/m2 values of fracture toughness are typical of the ductile metals involved in machining studies. This paper shows that when even the simple Ernst–Merchant analysis is generalised to include significant surface work, many of the experimental observations for which traditional ‘plasticity and friction only’ analyses seem to have no quantitative explanation, are now given meaning. In particular, the primary shear plane angle φ becomes material-dependent. The experimental increase of φ up to a saturated level, as the uncut chip thickness is increased, is predicted. The positive intercepts found in plots of cutting force vs. depth of cut, and in plots of force resolved along the primary shear plane vs. area of shear plane, are shown to be measures of the specific surface work. It is demonstrated that neglect of these intercepts in cutting analyses is the reason why anomalously high values of shear yield stress are derived at those very small uncut chip thicknesses at which the so-called size effect becomes evident. The material toughness/strength ratio, combined with the depth of cut to form a non-dimensional parameter, is shown to control ductile cutting mechanics. The toughness/strength ratio of a given material will change with rate, temperature, and thermomechanical treatment and the influence of such changes, together with changes in depth of cut, on the character of machining is discussed. Strength or hardness alone is insufficient to describe machining. The failure of the Ernst–Merchant theory seems less to do with problems of uniqueness and the validity of minimum work, and more to do with the problem not being properly posed. The new analysis compares favourably and consistently with the wide body of experimental results available in the literature. Why considerable progress in the understanding of metal cutting has been achieved without reference to significant surface work is also discussed.

Web-based occupant feedback for building energy management systems using fuzzy logic

This paper describes the development and validation of a novel web-based interface for the gathering of feedback from building occupants about their environmental discomfort including signs of Sick Building Syndrome (SBS). The gathering of such feedback may enable better targeting of environmental discomfort down to the individual as well as the early detection and subsequently resolution by building services of more complex issues such as SBS. The occupant's discomfort is interpreted and converted to air-conditioning system set points using Fuzzy Logic. Experimental results from a multi-zone air-conditioning test rig have been included in this paper.