Can oil, plastic and RAP wastes have a new life in novel asphalt mixtures?

The pavement recycling allows to reuse reclaimed asphalt pavement (RAP) or other waste materials in new asphalt mixtures for road construction or rehabilitation, thus re-ducing the use of virgin materials (aggregates and bitumen). Thus, the main aim of this study is to minimize the use of natural resources through the reuse of three waste materials: HDPE, mo-tor oil and RAP. Different amounts of waste motor oil and HDPE were added to an asphalt binder with 50% aged bitumen. The best solutions to produce the modified binders (4.5 to 5.0% HDPE and 10 % waste motor oil) performed as well as a conventional bitumen although they only used 35 % of virgin bitumen. Asphalt mixtures with 50 % RAP were produced with the selected modified binders, improving some characteristics in comparison with conventional asphalt mixtures. In conclusion, these wastes can revive in new asphalt mixtures.

Evaluation of foamed bitumen efficiency in warm asphalt mixtures recycling

The recycling of pavements is nowadays a very important question to the road paving industry. With the objective of incorporating higher percentages of reclaimed asphalt (RA) materials in recycled asphalt mixtures, new techniques have been developed in the last years. The use of foamed bitumen is normally associated with the production of cold asphalt mixtures, which usually show lower quality standards. However, the objective of the work presented in this paper is to assess the use of foamed bitumen as the binder of warm asphalt mixtures incorporating 30% RA, which have quality standards similar to those of conventional mixtures. Thus, five mixtures have been produced with 30% RA, one of them with a conventional bitumen (control mix) and the others with foamed bitumen at different production temperatures. The mixtures were tested for compactability and water sensitivity and the results show a possible reduction of 25 ºC in the production temperatures, while the water sensitivity test results were kept close to 90 %.

Plastic waste use as aggregate and binder modifier in open-graded asphalts

Road pavements are very important infrastructures for the Society, but they can cause serious environmental impacts during construction, operation and rehabilitation phases. Thus, it is essential to develop surface paving solutions that promote not only the durability but also a comfortable and safe use. In fact, this work aims to study the properties of new opengraded mixtures for surface layers produced with plastic wastes. First, HDPE and EVA wastes were used as bitumen modifiers, and then another plastic waste (PEX) replaced part of the aggregates. After studying the modified binders, the open-graded mixtures were designed, and then they were tested concerning their particle loss, rutting resistance, surface texture and damping effect. It was concluded that both ways of using the plastic wastes can improve the mechanical and functional properties of the open-graded mixtures related to the pavement performance.

Mechanical analysis of asphalt mixtures produced with waste plastic modified binders

This work compares the viscoelastic properties of an asphalt binder (70/100 pen) modified with different waste plastics and the mechanical properties of the resultant asphalt mixtures. Two different plastic wastes were used, namely recycled HDPE and EVA. Three different polymer modified binders were produced with these plastic wastes: i) 5% HDPE modified binder (P5); ii) 5% EVA modified binder (E5) and; iii) a modified binder with 4% of EVA and 2% HDPE (E4P2). Asphalt mixtures were produced with these modified binders, and their mechanical properties were analysed and compared with a conventional mixture produced with a 30/50 pen bitumen. It was possible to conclude that these recycled polymers are able to improve the mechanical performance of the asphalt mixtures used in road paving.

A mechanical analysis of asphalt recycled mixtures produced with high recycling rates

In this work four asphalt mixtures were compared in terms of mechanical characteristics. One of the mixtures (control mixture) was used as a reference to the study of three mixtures produced with reclaimed asphalt pavement (RAP). One of the recycled mixtures incorporated 30% of RAP and the other two were produced with 50% of RAP. The effect of using a rejuvenator additive (3% rejuvenator) was also evaluated in one of the mixtures with 50% of RAP.

Utilization of waste materials to improve asphalt mixtures performance

This study aims to develop an innovative bitumen with large quantities of waste materials to improve asphalt mixtures performance. Different amounts of waste motor oil and waste HDPE were added to a new bitumen. The bitumen modified with 10% of waste motor oil and 5% of HDPE showed promising characteristics (high softening point temperatures and penetration slightly higher than the conventional bitumen). After the selection of the most promising modified bitumen, three asphalt mixtures were produced with different bitumens (namely conventional bitumen, commercial modified bitumen and the selected modified bitumen). Beyond that, this modified bitumen improved some mechanical characteristics of the asphalt mixture where it was used, in comparison to conventional and modified asphalt mixtures.

Effect of incorporating different waste materials in bitumen

The increasing environmental concern about waste materials and the necessity of improving the performance of asphalt mixtures prompted the study of incorporating different waste materials in conventional bitumen. The reuse of waste materials can present benefits at an environmental and economic level, and some wastes can be used to improve the pavement performance. Thus, the purpose of this study is to evaluate the incorporation of different waste materials in bitumen, namely waste motor oil and different polymers. In order to accomplish this goal, 10% of waste motor oil and 5% of polymers (high density polyethylene, crumb rubber and styrene-butadiene-styrene) were added to a conventional bitumen and the resulting modified bitumens were characterized through basic and rheological tests. From this work, it can be concluded that the incorporation of different waste materials improve some important properties of the conventional bitumen. Such improvements might indicate a good behaviour at medium/high temperatures and an increase of fatigue and rutting resistance. Therefore, these modified bitumens with waste materials can contribute to a sustainable development of road paving industry due to their performance and environmental advantages.

Foamed Bitumen: an alternative way of producing asphalt mixtures

With the constant need to improve and make the production of asphalt mixtures more sustainable, new production techniques have been developed, the implementation of which implies the correct knowledge of their performance. One of the most promising asphalt production techniques is the use of foamed bitumen. However, it is essential to understand how this binder will behave when subject to the expansion process. The loss of volume of the foamed bitumen could be translated by a decay curve, which allows to determine the ideal temperature and water content added to the bitumen in order to assure adequate conditions to the mix the bitumen with the aggregates. On the present study, a conventional 160/220 pen grade bitumen was tested by using different temperatures and water contents, and it was concluded that the optimum temperature for the production of foamed bitumen (with the studied bitumen) is 150 ºC, which corresponds to a viscosity of 0.1 Pa.s. The water content mostly influence the half-life of the bitumen foam, resulting in quicker volume reductions for higher water contents.

Study of the interaction between asphalt and plastic wastes in new polymer modified binders (PMB)

The aim of this study is evaluating the interaction between several base pen grade asphalt binders (35/50, 50/70, 70/100, 160/220) and two different plastic wastes (EVA and HDPE), for a set of new polymer modified binders produced with different amounts of both plastic wastes. After analysing the results obtained for the several polymer modified binders evaluated in this study, including a commercial modified binder, it can be concluded that the new PMBs produced with the base bitumen 70/100 and 5% of each plastic waste (HDPE or EVA) results in binders with very good performance, similar to that of the commercial modified binder.

Evolution of the surface plasmon resonance of Au:TiO2 nanocomposite thin films with annealing temperature

This paper reports on the changes in the structural and morphological features occurring in a particular type of nanocomposite thin-film system, composed of Au nanoparticles (NPs) dispersed in a host TiO2 dielectric matrix. The structural and morphological changes, promoted by in-vacuum annealing experiments of the as-deposited thin films at different temperatures (ranging from 200 to 800 C), resulted in a well-known localized surface plasmon resonance (LSPR) phenomenon, which gave rise to a set of different optical responses that can be tailored for a wide number of applications, including those for optical-based sensors. The results show that the annealing experiments enabled a gradual increase of the mean grain size of the Au NPs (from 2 to 23 nm), and changes in their distributions and separations within the dielectric matrix. For higher annealing temperatures of the as-deposited films, a broad size distribution of Au NPs was found (sizes up to 100 nm). The structural conditions necessary to produce LSPR activity were found to occur for annealing experiments above 300 C, which corresponded to the crystallization of the gold NPs, with an average size strongly dependent on the annealing temperature itself. The main factor for the promotion of LSPR was the growth of gold NPs and their redistribution throughout the host matrix. On the other hand, the host matrix started to crystallize at an annealing temperature of about 500 C, which is an important parameter to explain the shift of the LSPR peak position to longer wavelengths, i.e. a red-shift.

A cost study of common surface finish systems for steel structures

This paper presents part of a study aimed at finding a suitable, yet cost-effective, surface finish for a steel structure subject to the car washing environment and corrosive chemicals. The initial, life cycle and average equivalent annual (AEAC) costs for surface finishing methods were calculated for a steel structure using the LCCC algorithm developed by American Galvanizers Association (AGA). The cost study consisted of 45 common surface finish systems including: hot-dip galvanization (HDG), metallization, acrylic, alkyd and epoxy as well as duplex coatings such as epoxy zinc and inorganic zinc (IOZ). The results show that initial, life cycle and AEAC costs for hot dip galvanization are the lowest among all the other methods, followed by coal tar epoxy painting. The annual average cost of HDG for this structure was estimated about €0.22/m2, while the other cost-effective alternatives were: IOZ, polyurea, epoxy waterborne and IOZ/epoxy duplex coating.

Desenvolvimento de uma metodologia de avaliação da resistência ao rolamento de diferentes misturas betuminosas

Os pavimentos rodoviários são infraestruturas de grande importância para o desenvolvimento económico de qualquer país. Atualmente, o principal critério utilizado na conceção dessas infraestruturas deixou de ser apenas o seu menor custo, valorizando-se a perspetiva ambiental e procurando determinar todos os impactos de longo prazo (económicos, ambientais ou sociais) deste tipo de investimentos. Nesse sentido, o consumo de combustível dos veículos que circulam nos pavimentos tem um peso significativo em termos económicos e ambientais, justificando a procura de soluções que permitam reduzir esse consumo de forma a garantir um desenvolvimento mais sustentável. No que diz respeito às características dos pavimentos, um dos fatores que mais influencia o consumo dos veículos é a resistência ao rolamento. Tendo em conta que as características dos pavimentos, em especial as superficiais, têm uma influência significativa nessa propriedade, com o presente trabalho pretendeu desenvolver-se uma metodologia de avaliação da resistência ao rolamento de misturas betuminosas com diferentes características superficiais. Assim, é possível avaliar que misturas ou características superficiais permitem contribuir para uma redução do consumo de combustível e das emissões de gases resultantes da sua queima ao longo do ciclo de vida de um pavimento. A obtenção de resultados do consumo energético necessário para circular sobre diferentes misturas betuminosas foi conseguida através do desenvolvimento de um protótipo. O consumo energético do movimento circular das rodas, equipadas com pneus convencionais de veículos ligeiros, foi medido para diferentes superfícies e a sua utilização para a avaliação da sustentabilidade das misturas estudadas é analisada no presente artigo

Regeneração de misturas betuminosas recicladas pela utilização de betumes modificados

Atualmente, a reciclagem de materiais assume uma importância crescente para a Sociedade, e em particular no que diz respeito ao sector da construção. Nas infraestruturas rodoviárias caminha-se no mesmo sentido, uma vez que a reutilização de materiais nas misturas betuminosas permite fazer frente ao gradual aparecimento duma grande diversidade de resíduos, sendo ainda possível reduz ir os custos de produção. De facto, a reutilização de materiais nas misturas betuminosas permite a redução dos custos, a redução do impacto ambiental, e a necessidade de utilização de novos agregados e ligantes betuminosos, constituindo um ciclo fechado de vida do material. O presente artigo tem como objetivo apresentar as vantagens da utilização de betumes modificados comerciais e produzidos em laboratório na regeneração ou na melhoria do desempenho de misturas betuminosas com elevadas taxas de reciclagem. Os materiais utilizados no estudo foram material fresado (50%), agregados novos, polímeros e betumes. Na modificação dos betumes base foram utilizados polímeros virgens (SBS) e reciclados (EVA), sendo ainda utilizado um betume modificado comercial. Os ensaios laboratoriais demonstram que a utilização de betumes modificados como materiais regeneradores melhora significativamente o desempenho das misturas à deformação permanente, por comparação com uma mistura betuminosa reciclada de referência com um rejuvenescedor comercial. No que diz respeito à sensibilidade à água todas as misturas produzidas com estes betumes regeneradores demonstram um excelente resultado. Porém, a mistura produzida com o betume modificado comercial destaca-se das restantes pela maior capacidade em resistir a este fenómeno. Considera-se que de uma forma geral os resultados obtidos neste trabalho trouxeram novas perspetivas no que respeita ao processo de regeneração dos betumes presentes no material fresado e na reciclagem de misturas betuminosas

Thin films composed of gold nanoparticles dispersed in a dielectric matrix: the influence of the host matrix on the optical and mechanical responses

Gold nanoparticles were dispersed in two different dielectric matrices, TiO2 and Al2O3, using magnetron sputtering and a post-deposition annealing treatment. The main goal of the present work was to study how the two different host dielectric matrices, and the resulting microstructure evolution (including both the nanoparticles and the host matrix itself) promoted by thermal annealing, influenced the physical properties of the films. In particular, the structure and morphology of the nanocomposites were correlated with the optical response of the thin films, namely their localized surface plasmon resonance (LSPR) characteristics. Furthermore, and in order to scan the future application of the two thin film system in different types of sensors (namely biological ones), their functional behaviour (hardness and Young's modulus change) was also evaluated. Despite the similar Au concentrations in both matrices (~ 11 at.%), very different microstructural features were observed, which were found to depend strongly on the annealing temperature. The main structural differences included: (i) the early crystallization of the TiO2 host matrix, while the Al2O3 one remained amorphous up to 800 °C; (ii) different grain size evolution behaviours with the annealing temperature, namely an almost linear increase for the Au:TiO2 system (from 3 to 11 nm), and the approximately constant values observed in the Au:Al2O3 system (4–5 nm). The results from the nanoparticle size distributions were also found to be quite sensitive to the surrounding matrix, suggesting different mechanisms for the nanoparticle growth (particle migration and coalescence dominating in TiO2 and Ostwald ripening in Al2O3). These different clustering behaviours induced different transmittance-LSPR responses and a good mechanical stability, which opens the possibility for future use of these nanocomposite thin film systems in some envisaged applications (e.g. LSPR-biosensors).

A Casa do Côto: entre a definição medieval e o desígnio contemporâneo

Dissertação de mestrado integrado em Arquitectura