Preparation of Ni-P electroless and its corrosion resistance against sea water

Electroless coating is much appropriate process at engineering surface. Since the discovery of electroless nickel-phosphorus coating in 3996, due to technical and economic advantages as well as desirable characteristics such as resistance to corrosion, abrasion and a high hardness has found wide application at engineering industries. Properties of electroless nickel-phosphorus coating depend on the characteristics of the used bath and heat treatment. In this study, optimal conditions and concentration of sodium citrate, sodium acetate and lactic acid in the bath of electroless nickel-phosphorus coating to the steel ck67 surface was determined. Structure, chemical composition and phases occurring in the coating were investigated using Scanning Electron Microscope (SEM) and X-ray diffraction analysis (XRD). The corrosion behavior of coatings in solution 3.5٪ NaCl was studied using electrochemical. The results showed that corrosion resistance of the coating with composition sodium citrate, sodium acetate and lactic acid decreased respectively.

Efeitos de absorventes de umidade e de aditivos químicos e microbianos sobre o valor nutritivo, o perfil fermentativo e as perdas em silagens de capim-marandu

The objective of this trial was to evaluate the nutritional value, fermentation profile and dry matter losses of Palisadegrass silages ensiled with either dried citrus pulp, soybean hulls, chemical or microbial additives. The trial was carried out in a completely randomized experimental design and in a factorial arrangement (3 x 5), with three dry matter levels (wet forage or forage ensiled with pelleted citrus pulp or pelleted soybean hulls) and five additives (without or with the presence of bacterial inoculants or the addition of: sodium benzoate, formic acid in the concentration of 62% or 44%), totalizing 15 treatments and 60 experimental silos. The variables analyzed were: nutritional value, losses due to gases and effluents, and dry matter recovery. The use of dried citrus pulp or soybean hulls at the ensiling time increased the dry matter content (29.4 and 28,9%) and decreased the effluent production (4.1 and 3.8 kg/t of fresh matter), also providing fermentable substrate to microorganisms, resulting in increased fermentation coefficient and digestibility of silages. The use of formic acid resulted in silages with higher digestibility and increased water-soluble carbohydrates and crude protein content. This additive was also effective in reducing the losses due to gases and, as a result, increased the total dry matter recovery. The treatment containing homolactic bacteria showed similar trend of increasing the digestibility and reducing the losses due to gases. The use of sodium benzoate was less effective in altering the fermentation pattern of tropical silages. The nutritional value and total dry matter losses of silages ensiled without additives can be considered satisfactory. However, wet forage ensiled with dried citrus pulp and, mainly, with soybeans hulls showed the best results. Treatments containing formic acid had a beneficial effect on the fermentation profile of tropical grass silages.

STANDARDIZATION OF CASSAVA MAHEWU FERMENTATION AND ASSESSMENT OF THE EFFECTS OF IRON SOURCES USED FOR FORTIFICATION

Cassava root is the main staple for 70% of the population in Mozambique, particularly in inaccessible rural areas, but is known to be low in iron. Anaemia is a public health problem in mothers and preschool children in Mozambique and up to 40% of these cases are probably due to dietary iron deficiency. The World Health Organization (WHO) and Food and Agriculture Organization of the United Nations (FAO) recognize the fortification of foodstuff as an effective method to remedy dietary deficiencies of micronutrients, including iron. Cassava mahewu, a non-alcoholic fermented beverage is prepared at subsistence level from cassava roots using indigenous procedures. The aim of the study was to standardize mahewu fermentation and investigate if the type of cassava fermented, or the iron compound used for fortification affected the final product. Roots of sweet and bitter varieties of cassava from four districts (Rapale, Meconta, Alto Molocue and Zavala) in Mozambique, were peeled, dried and pounded to prepare flour. Cassava flour was cooked and fermented under controlled conditions (45°C for 24 h). The fermentation period and temperature were set, based on the findings of a pilot study which showed that an end-point pH of about 4.5 was regularly reached after 24 h at 45°C. Cassava mahewu was fortified with ferrous sulfate (FeSO4.7H2O) or ferrous fumarate (C4H2FeO4) at the beginning (time zero) and at the end of fermentation (24 h). The amount of iron added to the mahewu was based on the average of the approved range of iron used for the fortification of maize meal. The mean pH at the endpoint was 4.5, with 0.29% titratable acidity. The pH and acidity were different to those reported in previous studies on maize mahewu, whereas the solid extract of 9.65% was found to be similar. Lactic acid bacteria (LAB) and yeast growth were not significantly different in mahewu fortified with either of the iron compounds. There was no significant difference between cassava mahewu made from bitter or sweet varieties. A standard method for preparation and iron fortification of cassava mahewu was developed. It is recommended that fortification occurs at the end of fermentation when done at household level.

Differential effects of low-temperature inhibition on the propylene induced autocatalysis of ethylene production, respiration and ripening of 'Hayward' kiwifruit

Previous studies (Stavroulakis and Sfakiotakis, 1993) have shown an inhibition of propylene-induced ethylene production in kiwifruit below a critical temperature range of 11-14.8 degrees C. The aim of this research was to identify the biochemical basis of this inhibition in kiwifruit below 11-14.8 degrees C. 'Hayward' kiwifruit were treated with increasing propylene concentrations at 10 and 20 degrees C. Ethylene biosynthesis pathways and fruit ripening were investigated. Kiwifruit at 20 degrees C in air started autocatalysis of ethylene production and ripened after 19 d with a concomitant increase in respiration. Ethylene production and the respiration rise appeared earlier with increased propylene concentrations. Ripening proceeded immediately after propylene treatment, while ethylene autocatalysis needed a lag period of 24-72 h. The latter event was attributed to the delay found in the induction of 1-aminocyclopropane-1-carboxylate synthase (ACC synthase) activity and consequently to the delayed increase of l-aminocyclopropane l-carboxylic acid (ACC) content. In contrast propylene treatment induced 1-aminocyclopropane-1-carboxylate oxidase (ACC oxidase) activity with no lag period. Moreover, transcription of ACC synthase and ACC oxidase genes was active only in ethylene-producing kiwifruit at 20 degrees C. In contrast, treatment at 10 degrees C with propylene strongly inhibited ethylene production, which was attributed to the low activities of both ACC synthase and ACC oxidase as well as the low initial ACC level. Interestingly, fruit treated with propylene at 10 degrees C appeared to be able to transcribe the ACC oxidase but not the ACC synthase gene. However, propylene induced ripening of that fruit almost as rapidly as in the propylene-treated fruit at 20 degrees C. Respiration rate was increased together with propylene concentration. It is concluded that kiwifruit stored at 20 degrees C behaves as a typical climacteric fruit, while at 10 degrees C behaves like a non-climacteric fruit. We propose that the main reasons for the inhibition of the propylene induced (autocatalytic) ethylene production in kiwifruit at low temperature (less than or equal to 10 degrees C), are primarily the suppression of the propylene-induced ACC synthase gene expression and the possible post-transcriptional modification of ACC oxidase.

Synthesis of innovative polyelectrolytes using monomers coming from renewable sources

240 p.

Síntese e caracterização do poli(ácido láctico) para potencial uso em sistemas de liberação controlada de fármacos

With the advances in medicine, life expectancy of the world population has grown considerably in recent decades. Studies have been performed in order to maintain the quality of life through the development of new drugs and new surgical procedures. Biomaterials is an example of the researches to improve quality of life, and its use goes from the reconstruction of tissues and organs affected by diseases or other types of failure, to use in drug delivery system able to prolong the drug in the body and increase its bioavailability. Biopolymers are a class of biomaterials widely targeted by researchers since they have ideal properties for biomedical applications, such as high biocompatibility and biodegradability. Poly (lactic acid) (PLA) is a biopolymer used as a biomaterial and its monomer, lactic acid, is eliminated by the Krebs Cycle (citric acid cycle). It is possible to synthesize PLA through various synthesis routes, however, the direct polycondensation is cheaper due the use of few steps of polymerization. In this work we used experimental design (DOE) to produce PLAs with different molecular weight from the direct polycondensation of lactic acid, with characteristics suitable for use in drug delivery system (DDS). Through the experimental design it was noted that the time of esterification, in the direct polycondensation, is the most important stage to obtain a higher molecular weight. The Fourier Transform Infrared (FTIR) spectrograms obtained were equivalent to the PLAs available in the literature. Results of Differential Scanning Calorimetry (DSC) showed that all PLAs produced are semicrystalline with glass transition temperatures (Tgs) ranging between 36 - 48 °C, and melting temperatures (Tm) ranging from 117 to 130 °C. The PLAs molecular weight characterized from Size Exclusion Chromatography (SEC), varied from 1000 to 11,000 g/mol. PLAs obtained showed a fibrous morphology characterized by Scanning Electron Microscopy (SEM)

Differential effects of low-temperature inhibition on the propylene induced autocatalysis of ethylene production, respiration and ripening of 'Hayward' kiwifruit

Previous studies (Stavroulakis and Sfakiotakis, 1993) have shown an inhibition of propylene-induced ethylene production in kiwifruit below a critical temperature range of 11-14.8 degrees C. The aim of this research was to identify the biochemical basis of this inhibition in kiwifruit below 11-14.8 degrees C. 'Hayward' kiwifruit were treated with increasing propylene concentrations at 10 and 20 degrees C. Ethylene biosynthesis pathways and fruit ripening were investigated. Kiwifruit at 20 degrees C in air started autocatalysis of ethylene production and ripened after 19 d with a concomitant increase in respiration. Ethylene production and the respiration rise appeared earlier with increased propylene concentrations. Ripening proceeded immediately after propylene treatment, while ethylene autocatalysis needed a lag period of 24-72 h. The latter event was attributed to the delay found in the induction of 1-aminocyclopropane-1-carboxylate synthase (ACC synthase) activity and consequently to the delayed increase of l-aminocyclopropane l-carboxylic acid (ACC) content. In contrast propylene treatment induced 1-aminocyclopropane-1-carboxylate oxidase (ACC oxidase) activity with no lag period. Moreover, transcription of ACC synthase and ACC oxidase genes was active only in ethylene-producing kiwifruit at 20 degrees C. In contrast, treatment at 10 degrees C with propylene strongly inhibited ethylene production, which was attributed to the low activities of both ACC synthase and ACC oxidase as well as the low initial ACC level. Interestingly, fruit treated with propylene at 10 degrees C appeared to be able to transcribe the ACC oxidase but not the ACC synthase gene. However, propylene induced ripening of that fruit almost as rapidly as in the propylene-treated fruit at 20 degrees C. Respiration rate was increased together with propylene concentration. It is concluded that kiwifruit stored at 20 degrees C behaves as a typical climacteric fruit, while at 10 degrees C behaves like a non-climacteric fruit. We propose that the main reasons for the inhibition of the propylene induced (autocatalytic) ethylene production in kiwifruit at low temperature (less than or equal to 10 degrees C), are primarily the suppression of the propylene-induced ACC synthase gene expression and the possible post-transcriptional modification of ACC oxidase.

High-performance multifunctional graphene-PLGA fibers: toward biomimetic and conducting 3D scaffolds

The development of electrically conducting fibers based on known cytocompatible materials is of interest to those engaged in tissue regeneration using electrical stimulation. Herein, it is demonstrated that with the aid of rheological insights, optimized formulations of graphene containing spinnable poly(lactic-co-glycolic acid) (PLGA) dopes can be made possible. This helps extend the general understanding of the mechanics involved in order to deliberately translate the intrinsic superior electrical and mechanical properties of solution-processed graphene into the design process and practical fiber architectural engineering. The as-produced fibers are found to exhibit excellent electrical conductivity and electrochemical performance, good mechanical properties, and cellular affinity. At the highest loading of graphene (24.3 wt%), the conductivity of as-prepared fibers is as high as 150 S m-1 (more than two orders of magnitude higher than the highest conductivity achieved for any type of nanocarbon-PLGA composite fibers) reported previously. Moreover, the Young's modulus and tensile strength of the base fiber are enhanced 647- and 59-folds, respectively, through addition of graphene.

First isolation and characterization of Chryseobacterium shigense from rainbow trout

BACKGROUND There have been an increasing number of infections in fish associated with different species of Chryseobacterium, being considered potentially emerging pathogens. Nevertheless the knowledge of the diversity of species associated with fish disease is partial due to the problems for a correct identification at the species level based exclusively on phenotypic laboratory methods. RESULTS Chryseobacterium shigense was isolated from the liver, kidney and gills of diseased rainbow trout in different disease episodes that occurred in a fish farm between May 2008 and June 2009. Identity of the isolates was confirmed by 16 S rRNA gene sequencing and phenotypic characterization. Isolates represented a single strain as determined by random amplified polymorphic DNA analysis. CONCLUSIONS This is the first description of the recovery of C. shigense from clinical specimens in trout, a very different habitat to fresh lactic acid beverage where it was initially isolated.

Grape and Wine Metabolites: Biotechnological Approaches to Improve Wine Quality

Grape metabolites can be affected by many extrinsic and intrinsic factors, such as grape variety, ripening stage, growing regions, vineyard management practices, and edaphoclimatic conditions. However, there is still much about the in vivo formation of grape metabolites that need to be investigated. The winemaking process also can create distinct wines. Nowadays, wine fermentations are driven mostly by single-strain inoculations, allowing greater control of fermentation. Pure cultures of selected yeast strains, mostly Saccharomyces cerevisiae, are added to grape must, leading to more predictable outcomes and decreasing the risk of spoilage. Besides yeasts, lactic acid bacteria also play an important role, in the final wine quality. Thus, this chapter attempts to present an overview of grape berry physiology and metabolome to provide a deep understanding of the primary and secondary metabolites accumulated in the grape berries and their potential impact in wine quality. In addition, biotechnological approaches for wine quality practiced during wine alcoholic and malolactic fermentation will also be discussed.

Quality improvement of traditional dry fermented sausages based on innovative technological strategies

Dry fermented sausages are highly appreciated food specialties, mainly in Portugal and other southern European countries. Therefore, all research efforts aiming at improving the food quality and safety of traditional dry sausages are of interest, since they are likely to result in products with higher added value and quality standards most suited to the requirements and concerns of the modern consumers. Among those efforts, it may be highlighted the studies involving innovative processing parameters and technologies to overcome practical problems gathered in the meat industry, which are mostly associated with food quality and safety. Additionally, characterization of traditional dry sausages and rationalization of their processing are essential for further achievement of any official certification. Thus, this article attempts to point out some research lines of highest interest in meat science (and particularly to the broad variety of regional dry fermented sausages), towards to the valorisation of technological, nutritional and commercial features. In addition, it is here emphasized the importance for the continuous improvement of the quality and safety of meat products as a way to respond to the current concerns regarding its consumption and the general advices in reducing its daily intake.

Dietary intervention with narrow-leaved cattail rhizome flour (Typha angustifolia L.) prevents intestinal inflammation in the trinitrobenzenesulphonic acid model of rat colitis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of the use of probiotic acid lactic bacteria in the development of chicken hambúrguer

The objective of this study was to investigate the effect of fermentation with Lactobacillus acidophilus CRL 1014 on the physicochemical, microbiological and sensory characteristics of a hamburger product like processed with chicken meat and okara flour, with reduction of curing salts. A mixture of ingredients containing 90% chicken meat and 10% okara flour was subjected to the following treatments: F1: fermented with Lactobacillus acidophilus; F2:75 mg nitrite/kg and fermented with Lactobacillus acidophilus; F3: 150 mg nitrite/kg and unfermented. The quality of the “hamburgers” was assessed by physical and chemical analysis (pH, cooking yield and shrinkage), chemical composition, microbiological tests (Salmonella spp., count of sulphite-reducing clostridia, staphylococos coagulase-positive, total coliforms and Escherichia coli) and sensory analysis (sensory acceptance and purchase intent). During the first six days of fermentation, there was a decrease in pH from approximately 6.33 to 5.10. All the samples showed the same chemical composition (p < 0.05). The fermentation process was observed to inhibit the multiplication of microorganisms of several groups: coagulasepositive staphylococci, sulphite-reducing clostridia, Salmonella spp. and E. coli. The different “hamburgers” formulations showed high scores for all the sensory attributes evaluated, without differing from each other (p < 0.05). The results showed that the use of L. acidophilus CRL 1014 enabled the production of a safe product, with good physicochemical and sensory characteristics, in the absence of curing salts.

In vitro and in vivo evaluation of the biocompatibility of a calcium phosphate/poly(lactic-co-glycolic acid) composite

This study assess the effects of bioceramic and poly(lactic-co-glycolic acid) composite (BCP/PLGA) on the viability of cultured macrophages and human dental pulp fibroblasts, and we sought to elucidate the temporal profile of the reaction of pulp capping with a composite of bioceramic of calcium phosphate and biodegradable polymer in the progression of delayed dentine bridge after (30 and 60 days) in vivo. Histological evaluation of inflammatory infiltrate and dentin bridge formation were performed after 30 and 60 days. There was similar progressive fibroblast growth in all groups and the macrophages showed viability. The in vivo study showed that of the three experimental groups: BCP/PLGA composite, BCP and calcium hydroxide (Ca(OH)(2)) dentin bridging was the most prevalent (90 %) in the BCP/PLGA composite after 30 days, mild to moderate inflammatory response was present throughout the pulp after 30 days. After 60 days was observed dentine bridging in 60 % and necrosis in 40 %, in both groups. The results indicate that understanding BCP/PLGA composite is biocompatible and by the best tissue response as compared to calcium hydroxide in direct pulp capping may be important in the mechanism of delayed dentine bridge after 30 and 60 days.

The influence of architecture on degradation and tissue ingrowth into three-dimensional poly(lactic-co-glycolic acid) scaffolds in vitro and in vivo

The in vitro and in vivo degradation properties of poly(lactic-co-glycolic acid) (PLGA) scaffolds produced by two different technologies-therm ally induced phase separation (TIPS), and solvent casting and particulate leaching (SCPL) were compared. Over 6 weeks, in vitro degradation produced changes in SCPL scaffold dimension, mass, internal architecture and mechanical properties. TIPS scaffolds produced far less changes in these parameters providing significant advantages over SCPL. In vivo results were based on a microsurgically created arteriovenous (AV) loop sandwiched between two TIPS scaffolds placed in a polycarbonate chamber under rat groin skin. Histologically, a predominant foreign body giant cell response and reduced vascularity was evident in tissue ingrowth between 2 and 8 weeks in TIPS scaffolds. Tissue death occurred at 8 weeks in the smallest pores. Morphometric comparison of TIPS and SCPL scaffolds indicated slightly better tissue ingrowth but greater loss of scaffold structure in SCPL scaffolds. Although advantageous in vitro, large surface area:volume ratios and varying pore sizes in PLGA TIPS scaffolds mean that effective in vivo (AV loop) utilization will only be achieved if the foreign body response can be significantly reduced so as to allow successful vascularisation, and hence sustained tissue growth, in pores less than 300 mu m. (C) 2005 Elsevier Ltd. All rights reserved.