Ductile fracture by multiple void growth and interaction ahead of a notch tip in polycrystalline plastic solids

The objectives of this paper are to study the effects of plastic anisotropy and evolution in crystallographic texture with deformation on the ductile fracture behaviour of polycrystalline solids. To this end, numerical simulations of multiple void growth and interaction ahead of a notch tip are performed under mode I, plane strain, small scale yielding conditions using two approaches. The first approach is based on the Hill yield theory, while the second employs crystal plasticity constitutive equations and a Taylor-type homogenization in order to represent the ductile polycrystalline solid. The initial textures pertaining to continuous cast Al-Mg AA5754 sheets in recrystallized and cold rolled conditions are considered. The former is nearly-isotropic, while the latter displays pronounced anisotropy. The results indicate distinct changes in texture in the ligaments bridging the voids ahead of the notch tip with increase in load level which gives rise to retardation in porosity evolution and increase in tearing resistance for both materials.

Effects of different modes of hot cross-rolling in 7010 aluminum alloy: part II. mechanical properties anisotropy

The influence of microstructure and texture developed by different modes of hot cross-rolling on in-plane anisotropy (A (IP)) of yield strength, work hardening behavior, and anisotropy of Knoop hardness (KHN) yield locus has been investigated. The A (IP) and work hardening behavior are evaluated by tensile testing at 0 deg, 45 deg, and 90 deg to the rolling direction, while yield loci have been generated by directional KHN measurements. It has been observed that specimens especially in the peak-aged temper, in spite of having a strong, rotated Brass texture, show low A (IP). The results are discussed on the basis of Schmid factor analyses in conjunction with microstructural features, namely grain morphology and precipitation effects. For the specimen having a single-component texture, the yield strength variation as a function of orientation can be rationalized by the Schmid factor analysis of a perfectly textured material behaving as a quasi-single crystal. The work hardening behavior is significantly affected by the presence of solute in the matrix and the state of precipitation rather than texture, while yield loci derived from KHN measurements reiterate the low anisotropy of the materials. Theoretic yield loci calculated from the texture data using the visco-plastic self-consistent model and Hill's anisotropic equation are compared with that obtained experimentally.

Representing a cubic graph as the intersection graph of axis-parallel boxes in three dimensions

We show that every graph of maximum degree 3 can be represented as the intersection graph of axis parallel boxes in three dimensions, that is, every vertex can be mapped to an axis parallel box such that two boxes intersect if and only if their corresponding vertices are adjacent. In fact, we construct a representation in which any two intersecting boxes just touch at their boundaries. Further, this construction can be realized in linear time.

Penetrative phototactic bioconvection in an isotropic scattering suspension

Phototaxis is a directed swimming response dependent upon the light intensity sensed by micro-organisms. Positive (negative) phototaxis denotes the motion directed towards (away from) the source of light. Using the phototaxis model of Ghorai, Panda, and Hill ''Bioconvection in a suspension of isotropically scattering phototactic algae,'' Phys. Fluids 22, 071901 (2010)], we investigate two-dimensional phototactic bioconvection in an absorbing and isotropic scattering suspension in the nonlinear regime. The suspension is confined by a rigid bottom boundary, and stress-free top and lateral boundaries. The governing equations for phototactic bioconvection consist of Navier-Stokes equations for an incompressible fluid coupled with a conservation equation for micro-organisms and the radiative transfer equation for light transport. The governing system is solved efficiently using a semi-implicit second-order accurate conservative finite-difference method. The radiative transfer equation is solved by the finite volume method using a suitable step scheme. The resulting bioconvective patterns differ qualitatively from those found by Ghorai and Hill ''Penetrative phototactic bioconvection,'' Phys. Fluids 17, 074101 (2005)] at a higher critical wavelength due to the effects of scattering. The solutions show transition from steady state to periodic oscillations as the governing parameters are varied. Also, we notice the accumulation of micro-organisms in two horizontal layers at two different depths via their mean swimming orientation profile for some governing parameters at a higher scattering albedo. (C) 2013 AIP Publishing LLC.

Role of surface chemistry in modulating drug release kinetics in titania nanotubes

Surface chemistry and the intrinsic porous architectures of porous substrates play a major role in the design of drug delivery systems. An interesting example is the drug elution characteristic from hydrothermally synthesised titania nanotubes with tunable surface chemistry. The variation in release rates of Ibuprofen (IBU) is largely influenced by the nature of the functional groups on titania nanotubes and pH of suspending medium. To elucidate the extent of interaction between the encapsulated IBU and the functional groups on titania nanotubes, the release profiles have been modelled with an empirical Hill equation. The analysis aided in establishing a probable mechanism for the release of IBU from the titania nanotubes. The study of controlled drug release from TiO2 has wider implication in the context of biomedical engineering. (C) 2014 Elsevier B.V. All rights reserved.

Molecules support morphology: species status of South Indian populations of the widely distributed Hanuman langur

The taxonomy of the Hanuman langur (Semnopithecus spp.), a widely distributed Asian colobine monkey, has been in a flux for a long time due to much disagreement between various classification schemes. However, results from a recent field-based morphological study were consistent with Hill's (Ceylon J Sci 21:277-305, 1939) species level classification scheme. Here we tested the validity of S. hypoleucos and S. priam, the two South Indian species recognized by Hill. To this end, one mitochondrial and four nuclear markers were sequenced from over 72 non-invasive samples of Hanuman langurs and S. johnii collected from across India. The molecular data were subjected to various tree building methods. The nuclear data was also used in a Bayesian structure analysis and to determine the genealogical sorting index of each hypothesized species. Results from nuclear data suggest that the South Indian population of Hanuman langur consists of two units that correspond to the species recognized by Hill. However in the mitochondrial tree S. johnii and S. priam were polyphyletic probably due to retention of ancestral polymorphism and/or low levels of hybridization. Implications of these results on conservation of Hanuman langurs are also discussed.

Specificity of the ModA11, ModA12 and ModD1 epigenetic regulator N-6-adenine DNA methyltransferases of Neisseria meningitidis

Phase variation (random ON/OFF switching) of gene expression is a common feature of host-adapted pathogenic bacteria. Phase variably expressed N-6-adenine DNA methyltransferases (Mod) alter global methylation patterns resulting in changes in gene expression. These systems constitute phase variable regulons called phasevarions. Neisseria meningitidis phasevarions regulate genes including virulence factors and vaccine candidates, and alter phenotypes including antibiotic resistance. The target site recognized by these Type III N-6-adenine DNA methyltransferases is not known. Single molecule, real-time (SMRT) methylome analysis was used to identify the recognition site for three key N. meningitidis methyltransferases: ModA11 (exemplified by M.NmeMC58I) (5'-CGY(m6)AG-3'), ModA12 (exemplified by M.Nme77I, M.Nme18I and M.Nme579II) (5'-AC(m6)ACC-3') and ModD1 (exemplified by M.Nme579I) (5'-CC(m6)AGC-3'). Restriction inhibition assays and mutagenesis confirmed the SMRT methylome analysis. The ModA11 site is complex and atypical and is dependent on the type of pyrimidine at the central position, in combination with the bases flanking the core recognition sequence 5'-CGY(m6)AG-3'. The observed efficiency of methylation in the modA11 strain (MC58) genome ranged from 4.6% at 5'-GCGC(m6)AGG-3' sites, to 100% at 5'-ACGT(m6)AGG-3' sites. Analysis of the distribution of modified sites in the respective genomes shows many cases of association with intergenic regions of genes with altered expression due to phasevarion switching.

Local structure of boundary layer transition in experiments with a single streamwise vortex

Transition induced by an isolated streamwise vortex embedded in a flat plate boundary layer was studied experimentally. The vortex was created by a gentle hill with a Gaussian profile that spanned on half of the width of a flat plate mounted in a low turbulence wind tunnel. PIV and hot-wire anemometry data were taken. Transition occurs as a non-inclined shear layer breaks up into a sequence of vortices, close to the boundary layer edge. The passing frequency of these vortices scales with square of the freestream velocity, similar to that in single-roughness induced transition. Quadrant analysis of streamwise and wall-normal velocity fluctuations show large ejection events in the outer layer. (C) 2015 Elsevier Inc. All rights reserved.

航天器稀疏编队飞行的概念及其设计方法

提出了航天器稀疏编队飞行的概念及其设计方法，阐明了它与通常的紧密编队飞行的区别及其在应用上的前景。采用了一个比Hill解更为广泛的新公式来设计稀疏编队，并列举了若干稀疏编队的阵形。当各航天器距离很近时，该公式自然退化为与Hill解相同的形式。通过与Hill解的设计相比较，表明了新公式用于稀疏编队设计的优越性。

Nemátodos fitoparásitos en palma africana Elaeis guineensis (Jacq) y cocotero Cocos nucifera L. en el Atlántico Sur, Nicaragua

Este estudio se llevó a cabo en plantaciones de Palma africana y cocotero de las regiones de Río San Juan y en la Región Autónoma del Atlántico Sur (R.A.A.S), con el objetivo de identificar nematodos asociados en ambos cultivos, contribuir a la actualización del listado nacional de nemátodos y determinar las infestación de Rhadinaphelencus cocophilus Cobb. en picudos (Rhynchophorus palmarum L.) de la palma y el cocotero Este trabajo se realizó en dos etapas; la primera consistió de dos muestreos (uno por región) y la última etapa fue de procesamiento y análisis de muestras. El primer muestreo se realizó en los lotes de las cooperativas Luisa A. Espinoza, El Borbollón y Teodoro Martinez en Kukra Hill para la palma africana y en coco se muestreo un lote del INTA, posteriormente se muestrearon las fincas; San Nicolás y San Mariano, luego se realizó un segundo muestreo en palma africana en el lote de la cooperativa Luisa A. Espinoza en Boca de Sábalos, Rio San Juan. La segunda etapa consistió en el análisis de las muestras; el cual se realizó inmediatamente después del muestreo. Se identificaron los géneros; Rotylenchulus, Trichodorus, Psilenchus, Aphe/enchoides, Paratylenchus, He/icotylenchus, Tylenchus, Xiphinema y Meloidogyne en el cultivo de palma africana y en cocotero se lograron identificar los siguientes géneros; Psílenchus, Aphelenchoides, Paratylenchus, Pratylenchus, Helicoty/enchus, Ty/enchus, Xiphinema y Rhadinaphelenchus. Para el cultivo de la palma africana, los géneros; Roty/enchus, Gracilacus, Psilenchus, Aphelenchoides, Paratylenchus y Meloidogyne fueron reportados por primera vez por lo que deberán ser agregados al listado nacional de plagas del MAG­FOR de la misma manera para el cultivo de coco, con los géneros; Aphelenchoides, Paratylenchus y Psilenchus. En los muestreos realizados en palma africana y coco en las localidades de Boca de Sábalos y en Kukra Hill se encontró la presencia de Rhynchophorus palmarum Linnaeus. En las fincas "San Nicolás" y "San Mariano", mas del 50 por ciento de los insectos (Rhynchophorus pa/marum Linnaeus) se encontraron infestados con el género Rhadinaphelenchus.

Salamanca, de poblado a ciudad : aproximación histórica a su origen, configuración y desarrollo sociourbanístico antes de la invasión musulmana

Resumen: En este artículo se aborda el origen, configuración y evolución urbana de Salamanca durante las ocupaciones soteña, celtibérica, romana y visigoda, comprendidas entre el siglo VII a.C., Primera Edad del Hierro, y la invasión musulmana de principios del siglo VIII d.C. La principal base documental la constituyen informes de las numerosas excavaciones arqueológicas, en su gran mayoría inéditos depositados en el Museo Provincial, realizadas a partir del año 1984 tanto en el cerro de San Vicente, núcleo germinal de la ciudad, como en el cerro de las Catedrales, núcleo de consolidación definitiva de Salamanca.

Micromechanics Modeling Of Strength For Nanocrystalline Copper

We present a model in this paper for predicting the inverse Hall-Petch phenomenon in nanocrystalline (NC) materials which are assumed to consist of two phases: grain phase of spherical or spheroidal shapes and grain boundary phase. The deformation of the grain phase has an elasto-viscoplastic behavior, which includes dislocation glide mechanism, Coble creep and Nabarro-Herring creep. However the deformation of grain boundary phase is assumed to be the mechanism of grain boundary diffusion. A Hill self-consistent method is used to describe the behavior of nanocrystalline pure copper subjected to uniaxial tension. Finally, the effects of grain size and its distribution, grain shape and strain rate on the yield strength and stress-strain curve of the pure copper are investigated. The obtained results are compared with relevant experimental data in the literature.

考虑晶界滑错的金属多晶体响应的自洽方法

首先建立含有三种介质(各向异性基体、各向异性夹杂、界面层)的平面应变夹杂模型.将基体和夹杂位移场展开为多项式级数,假设界面层很薄,运用变分原理得出这一问题的近似解.将上述夹杂问题的解和HILL自洽方法相结合,给出了考虑晶界滑错效应的金属多晶体弹塑性响应.

La economía familiar en sistemas de producción en comunidades del área de desarrollo territorial (ADT) del Municipio de Matigúas Matagalpa: Pasantías realizadas en Abril - Octubre en Fundación Ayuda en Acción proyecto " Desarrollo de la Economía Familiar (DEF.)"

Como una forma de culminación de estudios de la carrera de Licenciatura en Desarrollo Rural, las pasantías han sido realizadas en Fundación Ayuda en Acción (AeA), en el Área de Desarrollo Territorial (ADT) del Municipio de Matiguás-Matagalpa, en el período comprendido de Abril a Octubre del 2014. La Fundación AeA es una organización No Gubernamental de Desarrollo (ONGD) independiente, aconfesional y apartidista, fundada en España en 1981. Actualmente trabaja en 21 países en Asía, África y América Latina. En Nicaragua, la Fundación AeA está presente en: Matagalpa: Matiguás, Río Blanco y Tuma-La Dalia, Región Autónoma del Atlántico Sur (RAAS): Kukra Hill, León: Telica y Quezalguaque, Boaco: Boaco y Camoapa, Madriz: Totogalpa. Los proyectos que implementa son intersectoriales, articulando acciones en educación, salud, prevención de riesgos, gobernabilidad, seguridad y soberanía alimentaria entre otros, con la finalidad de impulsar cambios estructurales que contribuyan a la erradicación de la pobreza. El pasante a través de información primaria y secundaria consideró que la Fundación AeA era el organismo idóneo para realizar sus pasantías, ya que los proyectos que implementa se ajustan al perfil de la carrera de Licenciatura en Desarrollo Rural, al mismo tiempo se visualizó las condiciones favorables para su desempeño laboral. El área de trabajo asignada al pasante estuvo enfocada en proyectos productivos, dirigidos a mejorar los ingresos de las familias, dietas alimenticias, nutrición, así como la creación de conocimientos en diferentes temáticas a través capacitaciones. Entre las funciones asignadas al pasante se menciona: Realizar un estudio económico con productores sobre establecimiento de Sistemas Agroforestales (SAF) en cultivo de Cacao, fortalecer la organización comunitaria, levantar información primaria, elaborar herramientas para el levantamiento de base de datos, facilitar eventos de capacitación, reuniones, talleres e intercambios de experiencia, recolección de mensajes a niñez auspiciados, elaboración de informes, levantar información secundaria, coordinar y planificar con el equipo técnico. El análisis del estudio socioeconómico con productores sobre SAF en Cultivo de Cacao en el proyecto Desarrollo de Economía Familiar (DEF), demostró que el productor trabajando bajo un sistema técnico adecuado podrá obtener altos rendimientos productivos de hasta 15 quintales por manzana desde los 3 años. El pasante en el proyecto DEF, seleccionó en conjunto con el equipo técnico, 186 familias de 243 fichas analizadas los cuales trabajaron en componentes sobre establecimiento de SAF, hortalizas, cultivos en parra y crianza de especies menores. El proyecto de Soberanía y Seguridad Alimentaria y Nutricional (SSAN), ha estado enfocado en apoyar a 255 familias en 17 comunidades, estableciendo rubros, mejorando la calidad y consumo de agua (entrega de Rotoplas) a las familias y enriqueciendo sus conocimientos a través de capacitaciones en diferentes temas de género, comunicación asertiva, elaboración de alimentos, compartiendo experiencias con otras zonas de nuestro país. El pasante obtuvo lecciones como Identificación de diferentes actores locales en el municipio de Matiguás, como AeA, Alcaldía, Fundeser y Nitlapán, a través de iniciativa propia priorizó y gestionó las pasantías en la fundación AeA, relación con el equipo técnico recibiendo un proceso de inducción. La Fundación AeA debería continuar impartiendo talleres de capacitación en el ADT. En cuanto al desarrollo de las pasantías es necesario que desde un inicio se establezcan coordinaciones y planes entre la universidad y la institución donde el pasante desempeñara sus funciones.