Unsteady tip leakage characteristics and heat transfer on turbine blade tip and casing

An unsteady numerical investigation was performed to examine time dependent behaviors of the tip leakage flow structures and heat transfer on the rotor blade tip and casing in a single stage gas turbine engine. A transonic, high-pressure
turbine stage was modeled and simulated using a stage pressure ratio of 3.2. The rotor’s tip clearance was 1.2 mm in height (3% of the rotor span) and its speed was set at 9500 rpm. Periodic flow is observed for each vane passing period. Tip leakage flow as well as heat transfer data showed highly time dependent behaviors. A stator trailing edge shock appears as the turbine stage is operating at transonic conditions. The shock alters the flow condition in the rotor section, namely, the tip leakage flow structures and heat transfer rate distributions. The instantaneous Nusselt number distributions are compared to the time averaged and steady-state results. The same patterns in tip leakage flow
structures and heat transfer rate distributions were observed in both unsteady and steady simulations. However, the unsteady simulation captured the locally time-dependent high heat transfer phenomena caused by the unsteady interaction with the upstream vane trailing-edge shock and the passing wake.

Investigation of the solid-liquid phase transition of carbon at 150 GPa with spectrally resolved X-ray scattering

We have resolved the solid-liquid phase transition of carbon at pressures around 150GPa. High-pressure samples of different temperatures were created by laser-driven shock compression of graphite and varying the initial density from 1.30g/cm³ to 2.25g/cm³. In this way, temperatures from 5700K to 14,500K could be achieved for relatively constant pressure according to hydrodynamic simulations. From measuring the elastic X-ray scattering intensity of vanadium K-alpha radiation at 4.95keVat a scattering angle of 126°, which is very sensitive to the solid-liquid transition, we can determine whether the sample had transitioned to the fluid phase. We find that samples of initial density 1.3g/cm³ and 1.85g/cm³ are liquid in the compressed states, whereas samples close to the ideal graphite crystal density of 2.25g/cm³ remain solid, probably in a diamond-like state.

Femoral exostosis causing vastus medialis pain in an active young lady: a case report.

BACKGROUND:
Musculoskeletal conditions are a common reason for consultation to General Practitioners (GPs)/family physicians in primary care. Osteochondromas are the most common benign bone tumours and usually occur in the metaphyseal region of long bones. Despite the distal femur being the commonest location to find these benign bone tumours, this is the first case report in the literature specifically describing vastus medialis muscle pain as the presenting symptom due to underlying bursa formation secondary to local pressure effects.

CASE PRESENTATION:
Twenty nine year old female of white British ethnic origin, presenting to a primary care clinic with a three year history of intermittent left distal medial thigh pain.

CONCLUSION:
The benign bone tumour, femoral exostosis/osteochondroma, was diagnosed via Magnaetic Resonance Imaging (MRI) and treated conservatively, with surgical excision an option if not resolving. GPs/family physicians need to be aware of this diagnosis and that femoral exostosis/osteochondroma can present to primary care physicians, particularly within the second decade of life.

The complex ion structure of warm dense carbon measured by spectrally resolved x-ray scattering

We present measurements of the complex ion structure of warm dense carbon close to the melting line at pressures around 100 GPa. High-pressure samples were created by laser-driven shock compression of graphite and probed by intense laser-generated x-ray sources with photon energies of 4.75 keV and 4.95 keV. High-efficiency crystal spectrometers allow for spectrally resolving the scattered radiation. Comparing the ratio of elastically and inelastically scattered radiation, we find evidence for a complex bonded liquid that is predicted by ab-initio quantum simulations showing the influence of chemical bonds under these conditions. Using graphite samples of different initial densities we demonstrate the capability of spectrally resolved x-ray scattering to monitor the carbon solid-liquid transition at relatively constant pressure of 150 GPa. Showing first single-pulse scattering spectra from cold graphite of unprecedented quality recorded at the Linac Coherent Light Source, we demonstrate the outstanding possibilities for future high-precision measurements at 4th Generation Light Sources.

A Numerical and Experimental Assessment of the Use of a Turbine Utilizing Splitter Blades for an Automotive Variable Geometry Turbocharger

Automotive manufacturers require improved part load engine performance to further improve fuel economy. For a swing vane VGS (Variable Geometry Stator) turbine this means a more closed stator vane, to deal with the low MFRs (Mass Flow Rates), high PRs (Pressure Ratios) and low rotor rotational speeds. During these conditions the turbine is operating at low velocity ratios. As more energy is available at high pressure ratios and during lower turbocharger rotational speeds, a turbine which is efficient at these conditions is desirable. Another key aspect for automotive manufacturers is engine responsiveness. High inertia designs result in “turbo lag” which means an increased time before the target boost pressure is reached. Therefore, designs with improved performance at low velocity ratios, reduced inertia or an increased swallowing capacity are the current targets for turbocharger manufacturers.

To try to meet these design targets a CFD (Computational Fluid Dynamics) study was performed on a turbine wheel using splitter blades. A number of parameters were investigated. These included splitter blade merdional length, blade number and blade angle distribution.

The numerical study was performed on a scaled automotive VGS. Three different stator vane positions have been analysed. A single passage CFD model was developed and used to provide information on the flow features affecting performance in both the stator vanes and turbine.

Following the CFD investigation the design with the best compromise in terms of performance, inertia and increased MFP (Mass Flow Parameter) was selected for manufacture and testing. Tests were performed on a scaled, low temperature turbine test rig. The aerodynamic flow path of the gas stand was the same as that investigated during the CFD. The test results revealed a design which had similar performance at the closed stator vane positions when compared to the baseline wheel. At the maximum MFR stator vane condition a drop of −0.6% pts in efficiency was seen. However, 5.5% increase in MFP was obtained with the additional benefit of a drop in rotor inertia of 3.7%, compared to the baseline wheel.

A numerical study of automotive turbocharger mixed flow turbine inlet geometry for off design performance

Mixed flow turbines represent a potential solution to the increasing requirement for high pressure, low velocity ratio operation in turbocharger applications. While literature exists for the use of these turbines at such operating conditions, there is a lack of detailed design guidance for defining the basic geometry of the turbine, in particular, the cone angle – the angle at which the inlet of the mixed flow turbine is inclined to the axis. This investigates the effect and interaction of such mixed flow turbine design parameters.
Computational Fluids Dynamics was initially used to investigate the performance of a modern radial turbine to create a baseline for subsequent mixed flow designs. Existing experimental data was used to validate this model.
Using the CFD model, a number of mixed flow turbine designs were investigated. These included studies varying the cone angle and the associated inlet blade angle.
The results of this analysis provide insight into the performance of a mixed flow turbine with respect to cone and inlet blade angle.

A Numerical Study of the Flow Fields in a Highly Off-Design Variable Geometry Turbine

Conventionally, radial turbines have almost exclusively used radially fibred blades. While issues of mechanical integrity are paramount, there may be opportunities for improving turbine efficiency through a 3D blade design without exceeding mechanical limits. Off-design performance and understanding of the secondary flow structures now plays a vital role in the design decisions made for automotive turbocharger turbines. Of particular interest is extracting more energy at high pressure ratios and lower rotational speeds. Operating in this region means the rotor will experience high values of positive incidence at the inlet. A CFD analysis has been carried out on a scaled automotive turbine utilizing a swing vane stator system. To date no open literature exists on the flow structures present in a standard VGT system. Investigations were carried out on a 90 mm diameter rotor with the stator vane at the maximum, minimum and 25% mass flow rate positions. In addition stator vane endwall clearance existed at the hub side. From investigation of the internal flow fields of the baseline rotor, a number of areas that could be optimized in the future with three dimensional blading were identified. The blade loading and tip leakage flow near inlet play a significant role in the flow development further downstream at all stator vane positions. It was found that tip leakage flow and flow separation at off-design conditions could be reduced by employing back swept blading and redistributing the blade loading. This could potentially reduce the extent of the secondary flow structures found in the present study.

In silico analysis and DHPLC screening strategy identifies novel apoptotic gene targets of aberrant promoter hypermethylation in prostate cancer

BACKGROUND: Aberrant DNA methylation has been implicated as a key survival mechanism in cancer, whereby promoter hypermethylation silences genes essential for many cellular processes including apoptosis. Limited data is available on the methylation profile of apoptotic genes in prostate cancer (CaP). The aim of this study was to profile methylation of apoptotic-related genes in CaP using denaturing high performance liquid chromatography (DHPLC).

METHODS: Based on an in silico selection process, 13 genes were screened for methylation in CaP cell lines using DHPLC. Quantitative methylation specific PCR was employed to determine methylation levels in prostate tissue specimens (n = 135), representing tumor, histologically benign prostate, high-grade prostatic intraepithelial neoplasia and benign prostatic hyperplasia. Gene expression was measured by QRT-PCR in cell lines and tissue specimens.

RESULTS: The promoters of BIK, BNIP3, cFLIP, TMS1, DCR1, DCR2, and CDKN2A appeared fully or partially methylated in a number of malignant cell lines. This is the first report of aberrant methylation of BIK, BNIP3, and cFLIP in CaP. Quantitative methylation analysis in prostate tissues identified 5 genes (BNIP3, CDKN2A, DCR1, DCR2 and TMS1) which were frequently methylated in tumors but were unmethylated in 100% of benign tissues. Furthermore, 69% of tumors were methylated in at least one of the five-gene panel. In the case of all genes, except BNIP3, promoter hypermethylation was associated with concurrent downregulation of gene expression.

CONCLUSION: Future examination of this "CaP apoptotic methylation signature" in a larger cohort of patients is justified to further evaluate its value as a diagnostic and prognostic marker.

Discovery of DNA hypermethylation using a DHPLC screening strategy

Promoter hypermethylation is recognized as a hallmark of human cancer, in addition to conventional mechanisms of gene inactivation. As such, many new technologies have been developed over the past two decades to uncover novel targets of methylation and decipher complex epigenetic patterns. However, many of these are either labor intensive or provide limited data, confined to oligonucleotide hybridization sequences or enzyme cleavage sites and cannot be easily applied to screening large sets of sequences or samples. We present an application of denaturing high performance liquid chromatography (DHPLC), which relies on bisulfite modification of genomic DNA, for methylation screening. We validated DHPLC as a methylation screening tool using GSTP1, a well known target of methylation in prostate cancer. We developed an in silico approach to identify potential targets of promoter hypermethylation in prostate cancer. Using DHPLC, we screened two of these targets LGALS3 and SMAD4 for methylation. We show that DHPLC has an application as a fast, sensitive, quantitative and cost effective method for screening novel targets or DNA samples for DNA methylation.

Targeting of photooxidative damage on single-stranded DNA representing the bcr-abl chimeric gene using oligonucleotide-conjugates containing [Ru(phen)3](2+)-like photosensitiser groups

Photooxidative damage was induced predominantly at a single guanine base in a target DNA by irradiation (lambda > 330 nm) in the presence of complementary oligodeoxynucleotide conjugates (ODN-5'-linker-[Ru(phen)3]2+) (phen = 1,10-phenanthroline). The target DNA represents the b2a2 variant of the chimeric bcr-abl gene implicated in the pathogenesis of chronic myeloid leukaemia, and the sequence of the 17mer ODN component of the conjugate (3' G G T A G T T A T T C C T T C T T 5') was complementary to the junction region of the sense strand sequence of this oncogene. Two different conjugates were prepared, both of them by reaction of the appropriate succinimide ester with 5'-hexylamino-derivatised 17mer ODN. In Ru-ODN-1 (7) the linker was -(CH2)6-NHCO-bpyMe (-bpyMe = 4'-[4-methyl-2,2'-bipyridyl]), whereas in Ru-ODN-2 (13) it was -(CH2)6-NHCO-(CH2)3-CONH-phen. Photoexcitation of either of the conjugates when hybridised with the 32P-5'-end-labelled target 34mer 5'T G A C C A T C A A T A A G G A A G A A G21 C C C T T C A G C G G C C 3' (ODN binding site underlined) led to an alkali-labile site predominantly (> 90%) at the G21 base, which is at the junction of double-stranded and single-stranded regions of the hybrid. Greater yields were found with Ru-ODN-1 (7) than with Ru ODN-2 (13). In contrast to this specific cleavage with Ru-ODN-1 (7) or Ru-ODN-2 (13), alkali-labile sites were generated at all guanines when the 34mer was photolysed in the presence of the free sensitiser [Ru(phen)3]2+. Since [Ru(phen)3]2+ was shown to react with 2'-deoxyguanosine to form the diastereomers of a spiroiminodihydantoin derivative (the product from 1O2 reaction), 1O2 might also be an oxidizing species in the case of Ru-ODN-1 (7) and Ru-ODN-2 (13). Therefore to determine the range of reaction, a series of 'variant' targets was prepared, in which G21 was replaced with a cytosine and a guanine substituted for a base further towards the 3'-end (e.g. Variant 3; 5'T G A C C A T C A A T A A G G A A G A A C C G23 C T T C A G C G G32 C C3'). While it was noted that efficient reaction took place at distances apparently remote from the photosensitiser (e.g at G32, but not G23 for Variant 3), this effect could be attributed to hairpinning of the single-stranded region of the target. These results are therefore consistent with the photooxidative damage being induced by a reaction close to the photosensitiser rather than by a diffusible species such as 1O2.

Experimental analysis of air flow profiles in a double skin facade in a maritime climate

Glazed Double Skin Facades (DSF) offer the potential to improve the performance of all-glass building skins, common to commercial office buildings in which full facade glazing has almost become the standard. Single skin glazing results in increased heating and cooling costs over opaque walls, due to lower thermal resistance of glass, and the increased impact of solar gain through it. However, the performance benefit of DSF technology continues to be questioned and its operation poorly understood, particularly the nature of airflow through the cavity. This paper deals specifically with the experimental analysis of the air flow characteristics in an automated double skin façade. The benefit of the DSF as a thermal buffer, and to limit overheating is evaluated through analysis of an extensive set of parameters including air and surface temperatures at each level in the DSF, airflow readings in the cavity and at the inlet and outlet, solar and wind data, and analytically derived pressure differentials. The temperature and air-flow are monitored in the cavity of a DSF using wireless sensors and hot wire anemometers respectively. Automated louvre operation and building set-points are monitored via the BMS. Thermal stratification and air flow variation during changing weather conditions are shown to effect the performance of the DSF considerably and hence the energy performance of the building. The relative pressure effects due to buoyancy and wind are analysed and quantified. This research aims to developed and validate models of DSFs in the maritime climate, using multi-season data from experimental monitoring. This extensive experimental study provides data for training and validation of models.

Permeation of bioactive constituents from Arnica montana preparations through human skin in-vitro

This study investigated and characterised transdermal permeation of bioactive agents from a topically applied Arnica montana tincture. Permeation experiments conducted over 48 h used polydimethylsiloxane (silastic) and human epidermal membranes mounted in Franz-type diffusion cells with a methanol-water (50:50 v/v) receptor fluid. A commercially available tincture of A. montana L. derived from dried Spanish flower heads was a donor solution. Further donor solutions prepared from this stock tincture concentrated the tincture constituents 1, 2 and 10 fold and its sesquiterpene lactones 10 fold. Permeants were assayed using a high-performance liquid chromatography method. Five components permeated through silastic membranes providing peaks with relative retention factors to an internal standard (santonin) of 0.28, 1.18, 1.45, 1.98 and 2.76, respectively. No permeant was detected within 12 h of applying the Arnica tincture onto human epidermal membranes. However, after 12 h, the first two of these components were detected. These were shown by Zimmermann reagent reaction to be sesquiterpene lactones and liquid chromatography/diode array detection/mass spectrometry indicated that these two permeants were 11,13-dihydrohelenalin (DH) analogues (methacrylate and tiglate esters). The same two components were also detected within 3 h of topical application of the 10-fold concentrated tincture and the concentrated sesquiterpene lactone extract.

Extracção supercrítica de óleo de grainha de uva combinada com pré-tratamentos enzimáticos

Neste trabalho estudou-se a extracção supercrítica do óleo de grainha de uva, usando dióxido de carbono, e combinou-se este processo com um prétratamento enzimático da semente para aumentar o rendimento global da extracção. A qualidade dos extractos obtidos foi avaliada pelo seu conteúdo em triacilglicerídeos, perfil de ácidos gordos e capacidade antioxidante. Realizaram-se também alguns estudos exploratórios sobre a aplicação de um pré-tratamento de alta pressão (HPP) à grainha da uva. Adicionalmente, efectuou-se o estudo da extracção, fraccionamento e caracterização estrutural das procianidinas da grainha da uva, bem como a avaliação da sua capacidade antioxidante. A extracção de procianidinas da grainha da uva foi efectuada sequencialmente com metanol e acetona/água, tendo sido posteriormente fraccionadas por adição sucessiva de misturas metanol/clorofórmio progressivamente mais concentradas em clorofórmio. A caracterização das procianidinas foi feita por HPLC-UV e LC–MS, antes e depois de sujeitar as amostras a uma tiólise, e também por ESI-MS e ESI-MS/MS. Este estudo permitiu reportar, pela primeira vez, a ocorrência de procianidinas do tipo-A galoiladas na grainha da uva. Os resultados de HPLC-UV permitiram determinar o grau médio de polimerização das procianidinas e a sua composição monomérica em (+)- catequina, (-)-epicatequina e (-)-epicatequina-O-galato. Mostrou-se que a (+)- catequina é o flavan-3-ol terminal mais abundante e a (-)-epicatequina predomina largamente como unidade de extensão. No caso de procianidinas do tipo A, a ligação interflavânica C2-C7 encontra-se essencialmente nas unidades terminais. O grau médio de polimerização das diversas fracções varia entre 1.0 e 10.8. A sua capacidade antioxidante, medida pelo método espectrofotométrico de DPPH•, mostrou-se ser equivalente à de uma amostra comercial de (+)-catequina usada como referência. A partir dos graus médios de polimerização experimentais e das análises de FTIR das fracções correspondentes foi possível obter um modelo preditivo O-PLS com apenas uma variável latente. O pré-tratamento enzimático justificou-se pelo conhecimento existente acerca do uso de enzimas específicas que destroem parcialmente as paredes celulares. Atendendo à composição das paredes celulares da grainha da uva preparou-se uma suspensão contendo protease, xilanase, pectinase e celulase. Para determinar as condições experimentais do pré-tratamento que maximizam o rendimento da extracção, estudou-se o efeito do tempo de reacção, temperatura, pH, diâmetro médio das partículas de grainha moída e a concentração das enzimas. Os incrementos do rendimento da extracção de óleo observados atingiram 163.2%. O estudo da extracção supercrítica (SFE) do óleo da grainha de uva tratada e não-tratada permitiu obter as curvas de extracção correspondentes, bem com analisar a influência das condições operatórias sobre o seu andamento. Montou-se uma instalação laboratorial onde se realizaram experiências com dióxido de carbono a 160, 180, 200 e 220 bar e temperaturas de 313.15 e 323.15 K. Os rendimentos obtidos por SFE foram semelhantes aos de Soxhlet com n-hexano. As curvas de extracção medidas compreendem um primeiro período de extracção, onde se remove cerca de 92-97% do óleo disponível, e um segundo período, essencialmente difusional, com pouco impacto no rendimento final. Os vários extractos recolhidos e o óleo global obtido foram caracterizados para avaliar a sua qualidade e relacioná-la com as condições operatórias de SFE. Determinaram-se o conteúdo total em triacilglicerídeos, o seu perfil de ácidos gordos e a capacidade antioxidante (AOC). Os resultados mostraram que a AOC aumenta com a elevação da pressão e, acentuadamente, com o acréscimo da temperatura. Ao longo da curva de extracção, a AOC é mais pronunciada nos extractos iniciais, nomeadamente nos primeiros 30 a 40% da extracção. A modelação efectuada considerou que o óleo extractável se reparte entre células rompidas, predominantes na periferia da semente, e células intactas, mais interiores. Admitiu-se que o transporte de massa ocorre em série, i.e. das células intactas para as rompidas e destas para o solvente; mostrou-se que a dispersão axial era desprezável. Os balanços materiais à fase fluida e aos volumes de células rompidas e intactas, combinados com os fluxos interno, externo e a relação de equilíbrio foram resolvidos numericamente pelo método das linhas combinado com diferenças finitas atrasadas. O modelo reproduziu bem as curvas experimentais e permitiu simular curvas de eluição e os três perfis de concentração no leito.

Lichenicidin biosynthesis and search for novel antibacterial peptides

A estirpe Bacillus licheniformis I89 possui a capacidade de produzir alguns compostos com actividade antibacteriana. No presente estudo, a separação desses compostos foi realizada através da aplicação de vários procedimentos, incluindo extracção em fase sólida e cromatografia liquida de alta pressão. Dois destes compostos bioactivos constituem o lantibiótico de classe II lichenicidina e são caracterizados pela massas molecular de 3250 Da (Bliα) e 3020 Da (Bliβ). O cluster responsável pela biossíntese da lichenicidina foi heterologamente expresso em Escherichia coli, constituindo a primeira descrição da produção de um lantibiótico totalmente in vivo num hospedeiro Gram-negativo. Este sistema foi subsequentemente explorado com o objectivo de relacionar cada proteína codificada no cluster genético da lichenicidina na produção dos péptidos Bliα e Bliβ. O desenvolvimento do sistema de trans complementação possibilitou a produção de variantes destes péptidos. A análise das massas moleculares destas variantes assim como a análise dos padrões de fragmentação obtidos por MS/MS permitiu a revisão de algumas das características estruturais previamente proposta para Bliα e Bliβ. A análise dos genes hipoteticamente envolvidos na protecção da estirpe produtora contra a acção antibiótica da lichenicidina revelou, que em E. coli, a sua ausência não resulta no aumento da susceptibilidade a este composto. Verificou-se também que a presença destes genes não é essencial para a produção de lichenicidina em E. coli. Foi também confirmado experimentalmente que a membrana externa da E. coli constitui uma barreira natural para a entrada dos péptidos na célula. De facto, uma das características intrigantes da produção de lichenicidina por uma bactéria de Gram negativo reside no mecanismo de transporte dos dois péptidos através da membrana externa. Neste estudo foi demonstrado que na ausência da proteína de membrana TolC, a massa molecular de Bliα e Bliβ não foi identificada no sobrenadante de E. coli, demonstrando assim que a sua presença no ambiente extra-celular não se devia a um processo de lise bacteriana. Foi ainda avaliada a capacidade da maquinaria biossintética da lichenicidina para produzir o lantibiótico haloduracina, através do processamento de chimeras lichenicidina-haloduracina, contudo, os resultados foram negativos. Verificou-se ainda que em determinadas condições de incubação, a diferenciação da morfologia original da estirpe B. licheniformis I89 pode ocorrer. Esta dissociação implicou a transição da colónia parental e rugosa para uma colónia de aparência mais simples e suave. Desta forma, as diferenças das duas morfologias em termos de taxa de crescimento, esporulação e actividade antibiótica foram investigadas. Considerando especificamente Bliα e Bliβ verificou-se que a abundância destes péptidos nas culturas do fenótipo fino é geralmente inferior aquela identificada nas culturas do fenótipo parental. Por último, a diversidade de elementos genéticos constituintes de péptido sintetases não ribossomais (NRPS) foi investigada em lagoas no centro de Portugal e em solos provenientes de caves do sul de Portugal, revelando a presença de potenciais novas NRPS nestes ambientes.

Hole-type gaseous detectors for medical imaging and HEP experiments

This work presents the results on the development of a high pressure Xe gaseous detector envisaging medical imaging. The detector uses two VUV photosensors operating face-to-face, based on the CsI-MHSP with position discrimination capability. The known effect of the charge gain decrease with the gas pressure is compensated with a light gain using the electroluminescence process. Studies of signal amplitude, energy and position resolution are presented. On the second part, gaseous detectors based on THGEM where studied in order to fulfill the requirements of present and future high energy physics experiments. The work is focused on the application of THGEM in RICH detectors elements: a triple THGEM detector using CsI photocathodes in Ne mixtures was suggested. The ion backflow to the photocathode remains a concern and a limitation; to minimize it, the application of a new hole-structure, THCOBRA, was suggested. Preliminary results foresee good perspectives for the successful application of THCOBRA in ion back-flow suppression. This work contains several methods and measurements of the CsI photocathodes behaviour in radiation gaseous detectors. A long discussion on its issues and possible solutions are presented.