Flux line lattice structure and behavior in antiphase boundary free vicinal YBa2Cu3O7-delta thin films

Field angle dependent critical current, magneto-optical microscopy and high resolution electron microscopy studies have been performed on YBa2Cu3O7-delta thin films grown on miscut substrates. High resolution electron microscopy images show that the films studied exhibited clean epitaxial growth with a low density of antiphase boundaries and stacking faults. Any antiphase boundaries (APBs) formed near the film substrate interface rapidly healed rather than extending through the thickness of the film. Unlike vicinal films grown on annealed substrates, which contain a high density of antiphase boundaries, magneto-optical imaging showed no filamentary flux penetration in the films studied. The flux penetration is, however, asymmetric. This is associated with intrinsic pinning of flux strings by the tilted a-b planes and the dependence of the pinning force on the angle between the local field and the a-b planes. Field angle dependent critical current measurements exhibited the striking vortex channeling effect previously reported in vicinal films. By combining the results of three complementary characterization techniques it is shown that extended APB free films exhibit markedly different critical current behavior compared to APB rich films. This is attributed to the role of APB sites as strong pinning centers for Josephson string vortices between the a-b planes. (C) 2003 American Institute of Physics.

Reproductive physiology of ribbon fish (Trichiurus lepturus)

The ribbon fishes ‘of the family Trichiuridac are represented as one of the most important food resources in Indian ocean. High density of the dominant species of ribbon fish (Trichiurus lepturus) in Oman sea and the 'Tillable catch in last yeas (more than 7000 tones per year) makes a trust area for studing their population biolog and stock assessment. As our knowledge on reproductive biology of this species has an important role on their fisheries management, as well as conservation of this stock from decline or over fishing, this research was held to determine some aspects of reproductive physiology of ribbon fish and the effects of environmental factors in gonadal cycle. The goals of the present thesis is to determine some aspects of reproductive physiology such as gonadosomatic index (GSI) , hepatosomatic index (HSI), condition factor (Ko, fecundity, sex ratio, size at first maturity, size at maturity (LM5O) and their relative hormonal & biochemical fluctuations. In this regards annual variation of sex hormones ic. estradiol 17-B, progestron, cortisol, testostrone and gonadotropins FSH (GTH-I) , LH (GTH-ll)I were measured ; gonadal histological studies were done by light & electron micrography. The research was carried out from April 1995 to January 19% in Ras Nleidani in the north part of Oman sea, and the environmental factors such as temperature, salinity, oxygen, rainfall and pH were measured. The effects of these parameters on reproductive cycle and hormonal fluctuationswere discussed by using correlation and principle component analysis (PCA). Female Ribbon fish reproductive strategy shows the same paterns of nonguarder marine teleosts. T. lepturus has more than one spawning season (existance of egges in different size in each month) and therfore it must have asynchronous ovaries and belong to continious spawners. GSI and HSI are good evidences for this type of reproductive patern. The testis of the lobular type , which is typical of most teleosts , is composed of numerous lobules which are separated from each other by a thin layer of fibrous connective tissue. GSI fluctuations revealed prolong- spawning time in males. There is significant increase in 17-13 estradiol. progestrone , cortisol and gonadotropins with maturity and prespawning period of female T lepturus. Plasma concentration of E2 and GTH II incresaed along with water temperature increasing (3300).. Spawning was observed from Nov. 1995 to Apr. 1996 in this species. Progestrone increased significantly with increasing rainfall in this season (P<0.01). Plasma cortisol levels increased with maturation and vitelpgenesis and also with the peak of spawning. From lenght-weight frequency and size distribution in each age groups and also minimum size at first maturity (52a cm) it would he concluded that T. lepturus must be matured at 2 years of age. Serum cholestrol and triglicerides significantly increased when maturation occured in this species. The relationship between alkaline phosphatase activity and hormonal fluctuations with maturity and vitelogenesis were discussed. Proximate compostion (muscle) shows significant variation with spawning period and maturity. Absolute individual fecundity (17420-159150) increased with body length and weight. Ultrastructural observations show dramatic variation in cell membrane (0ocyte membrane), yolk vesicles and, nucleolus dispersal in relation to maturity stages. fluctuations of gonadal hormones were discused in relation with vitelogenesis. Testosterone increased in males from Nov: to Mar. due to environmental impacts and spawning time. Sex ratio in different depth (10-40 m ,80-110 m) shows significnt differences in this ratio for two depths. In 10-40 m depth female shows dominant abundance to male in each months that may be due to their reproductive migration behaviour. The effects of temperature photoperiod and rainfall to maturity and spawning were discussed. According to -pawning period of T. leptunts in our sampling area it could be suggested that ribbon fish fi,theries must be restricted in the peak of spawning seasons (Feb. to Mar.) and in the spawning grounds (under 40 m depths). Other suggestions for population conservation have been mentioned.

Preliminary observations on cage culture of Tilapia esculenta Graham and Tilapia xillii (Gervais) in Lake Victoria waters, at the Freshwater Fisheries Institute, Nyegezi, Tanzania

Cage culture of Tilapia is not suggested as a substitute for any known techniques in fish culture, but as one of the various techniques of obtaining more fish under controlled conditions. This fact has been very well accepted in various countries. Whererever facilities exist, this line of fish culture should be vigorously explored as a possible avenue in increasing fish production. High density stocking, management under controlled conditions, easy technique of fabricating the cage at relatively low cost, having no demand on land area, absence of prolific and effective breeding and easy availability of fish when a person needs it are a few of the attractions of the technique. The studies indicate that it is desirable to have different meshes for the cages, such as, small meshed cages for rearing fry to fingerlings stages, and larger meshed cages for rearing fingerlings to table sized fishes. II' the meshes are small, the resistance will be more and less water wilt pass through. While feeding with powdered food material, because of brisk activity of feeding fish, a part of the feed appeared wasted. This can be easily overcome if we would resort to feeding fish with cheap pelleted feeds which will no doubt reduce wastage. Precaution has to be taken against damage of the net and thereby loss of fish and against poaching by unauthorised persons. In the present attempt has been demonstrated the possibility of utilizing locally available species of Tilapia for cage culture and obtaining moderately satisfactory growth rates.

Engineering as a tool for improving human habitat

The conventional approaches to poverty alleviation in the slums entail a cocktail of interventions in health, education, governance and physical improvements, often stretching the scarce resources far and thin. Driven by the 'poverty' mindset, physical measures such as minimal paving, public water posts and community latrines actually brand the slums apart instead of assimilating them into the urban infrastructure fabric. The concept of Slum Networking proposes comprehensive water and environmental sanitation infrastructure as the central and catalytic leverage for holistic development. At costs less than the conventional 'slum' solutions, it tries to penetrate a high quality urban infrastructure net deeply into the slums to assimilate them into the city rather than lock them in as disadvantaged islands. Further, it transcends resource barriers and 'aid' through innovative partnerships and the latent resource mobilisation potential of the so-called 'poor'. This paper examines Slum Networking as implemented in Sanjaynagar in Ahmedabad, India and compares it with a similar settlement with no interventions in Ahmedabad. It assesses the knock-on impact of physical infrastructure on health, education and poverty. Finally, it evaluates the multiplier effect of physical infrastructure and the partnerships on the subsequent investments by the community in its own shelter and habitat. Copyright © 2009 Inderscience Enterprises Ltd.

Low temperature (< 100 °c) deposited P-type cuprous oxide thin films: Importance of controlled oxygen and deposition energy

With the emergence of transparent electronics, there has been considerable advancement in n-type transparent semiconducting oxide (TSO) materials, such as ZnO, InGaZnO, and InSnO. Comparatively, the availability of p-type TSO materials is more scarce and the available materials are less mature. The development of p-type semiconductors is one of the key technologies needed to push transparent electronics and systems to the next frontier, particularly for implementing p-n junctions for solar cells and p-type transistors for complementary logic/circuits applications. Cuprous oxide (Cu2O) is one of the most promising candidates for p-type TSO materials. This paper reports the deposition of Cu2O thin films without substrate heating using a high deposition rate reactive sputtering technique, called high target utilisation sputtering (HiTUS). This technique allows independent control of the remote plasma density and the ion energy, thus providing finer control of the film properties and microstructure as well as reducing film stress. The effect of deposition parameters, including oxygen flow rate, plasma power and target power, on the properties of Cu2O films are reported. It is known from previously published work that the formation of pure Cu2O film is often difficult, due to the more ready formation or co-formation of cupric oxide (CuO). From our investigation, we established two key concurrent criteria needed for attaining Cu2O thin films (as opposed to CuO or mixed phase CuO/Cu2O films). First, the oxygen flow rate must be kept low to avoid over-oxidation of Cu2O to CuO and to ensure a non-oxidised/non-poisoned metallic copper target in the reactive sputtering environment. Secondly, the energy of the sputtered copper species must be kept low as higher reaction energy tends to favour the formation of CuO. The unique design of the HiTUS system enables the provision of a high density of low energy sputtered copper radicals/ions, and when combined with a controlled amount of oxygen, can produce good quality p-type transparent Cu2O films with electrical resistivity ranging from 102 to 104 Ω-cm, hole mobility of 1-10 cm2/V-s, and optical band-gap of 2.0-2.6 eV. These material properties make this low temperature deposited HiTUS Cu 2O film suitable for fabrication of p-type metal oxide thin film transistors. Furthermore, the capability to deposit Cu2O films with low film stress at low temperatures on plastic substrates renders this approach favourable for fabrication of flexible p-n junction solar cells. © 2011 Elsevier B.V. All rights reserved.

Half-bridge SIC inverter for hybrid electric vehicles: Design, development and testing at higher operating temperature

In recent years, Silicon Carbide (SiC) semiconductor devices have shown promise for high density power electronic applications, due to their electrical and thermal properties. In this paper, the performance of SiC JFETs for hybrid electric vehicle (HEV) applications is investigated at heatsink temperatures of 100 °C. The thermal runaway characteristics, maximum current density and packaging temperature limitations of the devices are considered and the efficiency implications discussed. To quantify the power density capabilities of power transistors, a novel 'expression of rating' (EoR) is proposed. A prototype single phase, half-bridge voltage source inverter using SiC JFETs is also tested and its performance at 25 °C and 100 °C investigated.

Measurement of the elastic constants of nanometric films

Carbon coatings of thickness down to 2 nanometers are needed to increase the storage density in magnetic hard disks and reach the 100 Gbit/in2 target. Methods to measure the properties of these ultrathin hard films still have to be developed. We show that combining Surface Brillouin Scattering (SBS) andX-ray reflectivity measurements the elastic constants of such films are accessible. Tetrahedral amorphous carbofilms of thickness down to about 2 nm were deposited on Si by an S bend filtered cathodic vacuum arc, achieving a continuous coverage on large areas free of macroparticles. Film thickness and mass density are measured by X-ray reflectivity: densities above 3 g/cm3 are found, indicating a significant sp3 content. The dispersion relations of surface acoustic waves are measured by SBS. We show that for thicknesses above ∼4 nm these waves can be described by a continuum elastic model based on a single homogeneous equivalent film. The elastic constants can then be obtained by fitting the dispersion relations, computed for given film properties, to the measured dispersion relations. For thicknesses of 3 nm or less qualitative differences among films are well measurable, but quantitative results are less reliable. We have thus shown that we can grow and characterise nanometer size tetrahedral amorphous carbon film, which maintain their high density and peculiar mechanical properties down to around 4 nm thickness, satisfying the requirements set for the hard disk coating material.

Structural and thermodynamic properties of different phases of supercooled liquid water.

Computer simulation results are reported for a realistic polarizable potential model of water in the supercooled region. Three states, corresponding to the low density amorphous ice, high density amorphous ice, and very high density amorphous ice phases are chosen for the analyses. These states are located close to the liquid-liquid coexistence lines already shown to exist for the considered model. Thermodynamic and structural quantities are calculated, in order to characterize the properties of the three phases. The results point out the increasing relevance of the interstitial neighbors, which clearly appear in going from the low to the very high density amorphous phases. The interstitial neighbors are found to be, at the same time, also distant neighbors along the hydrogen bonded network of the molecules. The role of these interstitial neighbors has been discussed in connection with the interpretation of recent neutron scattering measurements. The structural properties of the systems are characterized by looking at the angular distribution of neighboring molecules, volume and face area distribution of the Voronoi polyhedra, and order parameters. The cumulative analysis of all the corresponding results confirms the assumption that a close similarity between the structural arrangement of molecules in the three explored amorphous phases and that of the ice polymorphs I(h), III, and VI exists.

Non-destructive characterization of structural hierarchy within aligned carbon nanotube assemblies

Understanding and controlling the hierarchical self-assembly of carbon nanotubes (CNTs) is vital for designing materials such as transparent conductors, chemical sensors, high-performance composites, and microelectronic interconnects. In particular, many applications require high-density CNT assemblies that cannot currently be made directly by low-density CNT growth, and therefore require post-processing by methods such as elastocapillary densification. We characterize the hierarchical structure of pristine and densified vertically aligned multi-wall CNT forests, by combining small-angle and ultra-small-angle x-ray scattering (USAXS) techniques. This enables the nondestructive measurement of both the individual CNT diameter and CNT bundle diameter within CNT forests, which are otherwise quantified only by delicate and often destructive microscopy techniques. Our measurements show that multi-wall CNT forests grown by chemical vapor deposition consist of isolated and bundled CNTs, with an average bundle diameter of 16 nm. After capillary densification of the CNT forest, USAXS reveals bundles with a diameter 4 m, in addition to the small bundles observed in the as-grown forests. Combining these characterization methods with new CNT processing methods could enable the engineering of macro-scale CNT assemblies that exhibit significantly improved bulk properties. © 2011 American Institute of Physics.

Confidence in beliefs about pain predicts expectancy effects on pain perception and anticipatory processing in right anterior insula.

Psychological factors play a major role in exacerbating chronic pain. Effective self-management of pain is often hindered by inaccurate beliefs about the nature of pain which lead to a high degree of emotional reactivity. Probabilistic models of perception state that greater confidence (certainty) in beliefs increases their influence on perception and behavior. In this study, we treat confidence as a metacognitive process dissociable from the content of belief. We hypothesized that confidence is associated with anticipatory activation of areas of the pain matrix involved with top-down modulation of pain. Healthy volunteers rated their beliefs about the emotional distress that experimental pain would cause, and separately rated their level of confidence in this belief. Confidence predicted the influence of anticipation cues on experienced pain. We measured brain activity during anticipation of pain using high-density EEG and used electromagnetic tomography to determine neural substrates of this effect. Confidence correlated with activity in right anterior insula, posterior midcingulate and inferior parietal cortices during the anticipation of pain. Activity in the right anterior insula predicted a greater influence of anticipation cues on pain perception, whereas activity in right inferior parietal cortex predicted a decreased influence of anticipatory cues. The results support probabilistic models of pain perception and suggest that confidence in beliefs is an important determinant of expectancy effects on pain perception.

Modulation of pain ratings by expectation and uncertainty: Behavioral characteristics and anticipatory neural correlates.

Expectations about the magnitude of impending pain exert a substantial effect on subsequent perception. However, the neural mechanisms that underlie the predictive processes that modulate pain are poorly understood. In a combined behavioral and high-density electrophysiological study we measured anticipatory neural responses to heat stimuli to determine how predictions of pain intensity, and certainty about those predictions, modulate brain activity and subjective pain ratings. Prior to receiving randomized laser heat stimuli at different intensities (low, medium or high) subjects (n=15) viewed cues that either accurately informed them of forthcoming intensity (certain expectation) or not (uncertain expectation). Pain ratings were biased towards prior expectations of either high or low intensity. Anticipatory neural responses increased with expectations of painful vs. non-painful heat intensity, suggesting the presence of neural responses that represent predicted heat stimulus intensity. These anticipatory responses also correlated with the amplitude of the Laser-Evoked Potential (LEP) response to painful stimuli when the intensity was predictable. Source analysis (LORETA) revealed that uncertainty about expected heat intensity involves an anticipatory cortical network commonly associated with attention (left dorsolateral prefrontal, posterior cingulate and bilateral inferior parietal cortices). Relative certainty, however, involves cortical areas previously associated with semantic and prospective memory (left inferior frontal and inferior temporal cortex, and right anterior prefrontal cortex). This suggests that biasing of pain reports and LEPs by expectation involves temporally precise activity in specific cortical networks.

Dynamics of strongly degenerate electron-hole plasmas and excitons in single InP nanowires.

Low-temperature time-resolved photoluminescence spectroscopy is used to probe the dynamics of photoexcited carriers in single InP nanowires. At early times after pulsed excitation, the photoluminescence line shape displays a characteristic broadening, consistent with emission from a degenerate, high-density electron-hole plasma. As the electron-hole plasma cools and the carrier density decreases, the emission rapidly converges toward a relatively narrow band consistent with free exciton emission from the InP nanowire. The free excitons in these single InP nanowires exhibit recombination lifetimes closely approaching that measured in a high-quality epilayer, suggesting that in these InP nanowires, electrons and holes are relatively insensitive to surface states. This results in higher quantum efficiencies than other single-nanowire systems as well as significant state-filling and band gap renormalization, which is observed at high electron-hole carrier densities.

Properties of electrons and holes during femtosecond cooperative emission

Spectral and energetic characteristics of the cooperative recombination of high density electrons and holes in bulk GaAs are experimentally studied at room temperature. It is shown that the properties and parameters of femtosecond superradiant pulses are conditioned by the collective properties of electrons and holes. Electron-hole pairing and the formation of a short-living coherent e-h BCS state distinguish strongly the regime of cooperative emission from all radiative e-h recombination regimes, which have been observed earlier. The dependences of the energy gap (the order parameter), the Fermi energy, and the band gap of the coherent e-h BCS state on the concentration of electron-hole pairs are obtained.

Isolation and characterization of Streptococcus dysgalactiae from diseased Acipenser schrenckii

Streptococcosis became an increasingly significant health problem in intensive aquaculture in China. Fifteen strains of Gram-positive, chain-forming coccus were isolated from moribund Amur sturgeon, Acipenser schrenckii, fanned with high density in central China. The coccoid microorganism was identified as Streptococcus dysgalactiae by means of physiological. biochemical properties and molecular analysis; furthermore, this coccus was confirmed as pathogen of sturgeon by challenge experiments and its infection potential on the cyprinid was also evaluated. To our knowledge, this was the first report of S. dysgalactiae linked to diseased A. schrenckii. (C) 2009 Elsevier B.V. All rights reserved.

Phenotypic plasticity in gut length in the planktivorous filter-feeding silver carp (Hypophthalmichthys molitrix)

Phenotypic plasticity widely exists in the external morphology of animals as well as the internal traits of organs. In the present study, we studied the gut length plasticity of planktivorous filter-feeding silver carp under different food resources in large-net cage experiments in Meiliang Bay of Lake Taihu in 2004 and 2005. There was a significant difference in stocking density between these 2 years. Under a low stocking density and abundant food resources, silver carp increased their energy intake by feeding on more zooplankton. Meanwhile, silver carp adjusted their gut length to match the digestive requirements of food when exposed to different food resources. In the main growth seasons (from April to October), silver carp significantly increased their relative gut length when feeding on more phytoplankton in 2005 (p < 0.01, 9.23 +/- 1.80 in 2004 and 10.77 +/- 2.05 in 2005, respectively). There was a nearly significant negative correlation between zooplankton proportion in the diet and the relative gut length when silver carp were stocked in a high density (p = 0.112). It appears that silver carp might have evolved plasticity to change their gut length rapidly to facilitate efficient utilization of food resources. Such resource polymorphisms in the gut may be a good indication of temporal adaptation to resource conditions. Our work provided field evidence for understanding the functional basis of resource polymorphisms and the evolution of phenotypic plasticity in planktivorous filter-feeding fish.