Application of logistic regression for fault analysis in an industrial printing process

A statistical technique for fault analysis in industrial printing is reported. The method specifically deals with binary data, for which the results of the production process fall into two categories, rejected or accepted. The method is referred to as logistic regression, and is capable of predicting future fault occurrences by the analysis of current measurements from machine parts sensors. Individual analysis of each type of fault can determine which parts of the plant have a significant influence on the occurrence of such faults; it is also possible to infer which measurable process parameters have no significant influence on the generation of these faults. Information derived from the analysis can be helpful in the operator's interpretation of the current state of the plant. Appropriate actions may then be taken to prevent potential faults from occurring. The algorithm is being implemented as part of an applied self-learning expert system.

Decentralized PID self-tuning control of industrial robots

A three degrees of freedom industrial robot is controlled by applying PID self-tuning (PID/ST) controllers. This control is considered as a corrective term to a nominal value, centrally computed from an inaccurate and/ or simplified dynamic model. An identification scheme on an assumed linear plant describing the deviation from the desired trajectory is employed in order to tune the controller coefficients and thus accomplish a behaviour prescribed through a desired pole placement. A salient feature of our approach is the decentralized nature of the controllers producing the corrective term for each joint. This opens the way to practical implementation, as recent computing requirement calculations for similar set-ups have shown in the literature. Numerical results are presented.

Projections of when temperature change will exceed 2°C above pre-industrial levels

Climate change projections are usually presented as 'snapshots' of change at a particular time in the future. Instead, we consider the key question 'when will specific temperature thresholds will be exceeded?'. Framing the question as "when might something happen (either permanently or temporarily)?" rather than "what might happen?" demonstrates that lowering future emissions will delay the crossing of temperature thresholds and buy valuable time for planning adaptation. For example, in higher greenhouse gas emission scenarios, a global average 2°C warming threshold is likely to be crossed by 2060, whereas in a lower emissions scenario, the crossing of this threshold is delayed up to several decades. On regional scales, however, the 2°C threshold will probably be exceeded over large parts of Eurasia, North Africa and Canada by 2040 if emissions continue to increase- well within the lifetime of many people living now.

Breaking free from the industrial age paradigm of branding

The paper aims to inform readers of the themes that emerged at the 2007 Thought Leaders International Conference on Brand Management and challenges academics and practitioners to rethink the basics of branding. The paper encourages academics and practitioners to escape from the continued confines of industrial age branding and the ‘influencing’ mindset and embrace the age of openness and co-creation. It is argued that we need to evolve from the industrial age paradigm of branding that informed brand management for decades and adjust practice and research accordingly.

Spatial concentration in institutional industrial real estate investment in the England and Wales

In two recent papers Byrne and Lee (2006, 2007) examined the geographical concentration of institutional office and retail investment in England and Wales at two points in time; 1998 and 2003. The findings indicate that commercial office portfolios are concentrated in a very few urban areas, whereas retail holdings correlate more closely with the urban hierarchy of England and Wales and consequently are essentially ubiquitous. Research into the industrial sector is very much less developed, and this paper therefore makes a significant contribution to understanding the structure of industrial property investment in the UK. It shows that industrial investment concentration is between that of retail and office and is focussed on LAs with high levels of manual workers in areas with smaller industrial units. It also shows that during the period studied the structure of the sector changed, with greater emphasis on the distributional element, for which location is a principal consideration.

Tillage and herbicide treatments with inter-row cultivation influence weed densities and yield of three industrial crops

Field experiments were conducted in northern Greece in 2003 and 2004 to evaluate effects of tillage regimes (moldboard plowing, chisel plowing, and rotary tilling), cropping sequences(continuous cotton, cotton-sugar beet rotation,and continuous tobacco) and herbicide treatments with inter-row hand hoeing on weed population densities. Total weed densities were not affected by tillage treatment except that of barnyardgrass (Echinochloa crus-galli), which increased only in moldboard plowing treated plots during 2003. Redroot pigweed (Amaranthus retroflexus)and black nightshade (Solanum nigrum) densities were reduced in continuous cotton, while purple nutsedge (Cyperus rotundus), E. crus-galli, S. nigrum, and johnsongras(Sorghum halepense) densities were reduced in tobacco. A. retroflexus and S. nigrum were effectively controlled by all herbicide treatments with inter-row hand hoeing,whereas E. crus-galli was effectively reduced by herbicides applied to cotton and tobacco. S. halepense density reduction was a result of herbicide applied to tobacco with inter-row hand hoeing. Yield of all crops was higher under moldboard plowing and herbicide treatments. Pre-sowing and pre-emergence herbicide treatments in cotton and pre-transplant in tobacco integrated with inter-row cultivation resulted in efficient control of annual weed species and good crop yields. These observations are of practical relevance to crop selection by farmers in order to maintain weed populations at economically acceptable densities through the integration of various planting dates, sustainable herbicide use and inter-row cultivation; tools of great importance in integrated weed management systems. Keywords: cropping sequence, herbicide, integrated weed management, inter-row cultivation,tillage.

EU enlargement and consequences for FDI-assisted industrial development

Many of the new member states as well as candidate and accession countries of the EU are confident that membership will result in substantially increased inward foreign direct investment (FDI) in manufacturing. This paper discusses the policy issues and challenges that cohesion and accession countries face, applying lessons that by now have become mainstream in the parallel discussion of FDI-assisted development in the developing economies. We argue that globalisation has attenuated the benefits that accrue from EU membership for latecomers, and they must now compete for FDI not just with other European countries but also with non- EU emerging economies. We posit that they should not base their industrial development strategy on mere passive reliance of FDI flows without considering how to concatenate their industrial development and the nature of the MNE activities they attract.