Geometry of Dirac Operators

Thesis (Master, Mathematics & Statistics) -- Queen's University, 2016-07-04 20:27:20.386

Confidentiala "Mode 3" Systems Approach for Knowledge Creation, Diffusion and Use: Towards a 21st Century Fractal Innovation Ecosystem. ACES Working Paper (Report) No. 4, 2007

"Mode 3" allows and emphasizes the co-existence and co-evolution of different knowledge and innovation paradigms: the competitiveness and superiority of a knowledge system is highly determined by its adaptive capacity to combine and integrate different knowledge and innovation modes via co-evolution, co-specialization and coopetition [sic] of knowledge stock and flow dynamics. What results is an emerging fractal knowledge and innovation ecosystem, well-configured for the knowledge economy and society. The intrinsic litmus test of the capacity of such an ecosystem to survive and prosper in the context of continually glocalizing [sic] and intensifying competition represents the ultimate competitiveness benchmark with regards to the robustness and quality of the ecosystem's knowledge and innovation architecture and topology.

Particel size distribution and microstructures of sediments from ODP Leg 205 sites (Table 1)

Ocean Drilling Program Legs 170 and 205 offshore Costa Rica provide structural observations which support a new model for the geometry and deformation response to the seismic cycle of the frontal sedimentary prism and decollement. The model is based on drillcore, thin section, and electron microscope observations. The decollement damage zone is a few tens of meters in width, it develops mainly within the frontal prism. A clear cm-thick fault core is observed 1.6 km from the trench. The lower boundary of the fault core is coincident with the lithological boundary between the frontal prism and the hemipelagic and pelagic sediment of the Cocos plate. Breccia clast distributions in the upper portion of the decollement damage zone were studied through fractal analysis. This analysis shows that the fractal dimension changes with brecciated fragment size, implying that deformation was not accommodated by self-similar fracturing. A higher fractal dimensionality correlates with smaller particle size, which indicates that different or additional grain-size reduction processes operated during shearing. The co-existence of two distinct fracturing processes is also confirmed by microscopic analysis in which extension fracturing in the upper part of the damage zone farthest from the fault core is frequent, while both extension and shear fracturing occur approaching the fault core. The coexistence of extensional and shear fracturing seems to be best explained by fluid pressure variations in response to variations of the compressional regime during the seismic cycle. During the co-seismic event, sub-horizontal compression and fluid pressure increase, triggering shear fracturing and fluid expulsion. Fractures migrate upward with fluids, contributing to the asymmetric shape of the decollement, while slip propagates. In the inter-seismic interval the frontal prismrelaxes and fluid pressure drops. The frontal prismgoes into diffuse extension during the intervalwhen plate convergence is accommodated by creep along the ductile fault core. The fault core is typically a barrier to deformation, which is explained by its weak, but impermeable, nature. The localized development of a damage zone beneath the fault core is characterized by shear fracturing that appears as the result of local strengthening of the detachment.

Greenland and Antarctic ice sheet topography, cavity geometry, and global bathymetry (RTopo-2), links to NetCDF files

The ocean plays an important role in modulating the mass balance of the polar ice sheets by interacting with the ice shelves in Antarctica and with the marine-terminating outlet glaciers in Greenland. Given that the flux of warm water onto the continental shelf and into the sub-ice cavities is steered by complex bathymetry, a detailed topography data set is an essential ingredient for models that address ice-ocean interaction. We followed the spirit of the global RTopo-1 data set and compiled consistent maps of global ocean bathymetry, upper and lower ice surface topographies and global surface height on a spherical grid with now 30-arc seconds resolution. We used the General Bathymetric Chart of the Oceans (GEBCO, 2014) as the backbone and added the International Bathymetric Chart of the Arctic Ocean version 3 (IBCAOv3) and the Interna- tional Bathymetric Chart of the Southern Ocean (IBCSO) version 1. While RTopo-1 primarily aimed at a good and consistent representation of the Antarctic ice sheet, ice shelves and sub-ice cavities, RTopo-2 now also contains ice topographies of the Greenland ice sheet and outlet glaciers. In particular, we aimed at a good representation of the fjord and shelf bathymetry sur- rounding the Greenland continent. We corrected data from earlier gridded products in the areas of Petermann Glacier, Hagen Bræ and Sermilik Fjord assuming that sub-ice and fjord bathymetries roughly follow plausible Last Glacial Maximum ice flow patterns. For the continental shelf off northeast Greenland and the floating ice tongue of Nioghalvfjerdsfjorden Glacier at about 79°N, we incorporated a high-resolution digital bathymetry model considering original multibeam survey data for the region. Radar data for surface topographies of the floating ice tongues of Nioghalvfjerdsfjorden Glacier and Zachariæ Isstrøm have been obtained from the data centers of Technical University of Denmark (DTU), Operation Icebridge (NASA/NSF) and Alfred Wegener Institute (AWI). For the Antarctic ice sheet/ice shelves, RTopo-2 largely relies on the Bedmap-2 product but applies corrections for the geometry of Getz, Abbot and Fimbul ice shelf cavities.

The geometry of selected U.S. tidal inlets /

"May 1980."

Topics in differential geometry.

Based on lectures given in the spring of 1949; a few of the latest results of work done since that time have been included.

Definition of the requirements in plane geometry, solid geometry, plane and solid geometry, major requirement, plane and solid geometry minor requirement /

Wm. F. Osgood, chairman.

The basic concepts of mathematics; a companion to current textbooks on algebra and analytic geometry.

pt.1. Algebra.

Analytic geometry,

"Answers to odd-numbered problems": p. 375-393.

Selected topics in algebraic geometry; report of the Committee on rational transformations:

Bibliography at end of each chapter.

Selected topics in algebraic geometry

Cover-title.

Lectures on classical differential geometry.

Bibliography: p. vii-viii.