Evaluation of a ToF Camera for Remote Surveying of Underground Cavities Excavated by Jet Boring

Cigar Lake is a high-grade uranium deposit, located in northern Saskatchewan, Canada. In order to extract the uranium ore remotely, thus ensuring minimal radiation dose to workers and also to access the ore from stable ground, the Jet Boring System (JBS) was developed by Cameco Corporation. This system uses a high-powered water jet to remotely excavate cavities. Survey data is required to determine the final shape, volume, and location of the cavity for mine planning purposes and construction. This paper provides an overview of the challenges involved in remotely surveying a JBS-mined cavity and studies the potential use of a time-of-flight (ToF) camera for remote cavity surveying. It reports on data collected and analyzed from inside an experimental environment as well as on real data acquired on site from the Cigar Lake and Rabbit Lake mines.

Effects of lycopene on the induction of foam cell formation by modified LDL.

The effect of lycopene on macrophage foam cell formation induced by modified low-density lipoprotein (LDL) was studied. Human monocyte-derived macrophages (HMDM) were incubated with lycopene in the presence or absence of native LDL (nLDL) or LDL modified by oxidation (oxLDL), aggregation (aggLDL), or acetylation (acLDL). The cholesterol content, lipid synthesis, scavenger receptor activity, and the secretion of inflammatory [interleukin (IL)-1β and tumor necrosis factor (TNF)-α] and anti-inflammatory (IL-10) cytokines was determined. Lycopene was found to decrease the synthesis of cholesterol ester in incubations without LDL or with oxLDL while triacylglycerol synthesis was reduced in the presence of oxLDL and aggLDL. Scavenger receptor activity as assessed by the uptake of acLDL was decreased by ∼30% by lycopene. In addition, lycopene inhibited IL-10 secretion by up to 74% regardless of the presence of nLDL or aggLDL but did not affect IL-1β or TNF-α release. Lycopene also reduced the relative abundance of mRNA transcripts for scavenger receptor A (SR-A) in THP-1 macrophages treated with aggLDL. These findings suggest that lycopene may reduce macrophage foam cell formation induced by modified LDL by decreasing lipid synthesis and downregulating the activity and expression of SR-A. However, these effects are accompanied by impaired secretion of the anti-inflammatory cytokine IL-10, suggesting that lycopene may also exert a concomitant proinflammatory effect.

The induction of macrophages foam cell formation by chylomicron remnants

The accumulation of foam cells in the artery wall causes fatty streaks, the first lesions in atherosclerosis. LDL (low-density lipoprotein) plays a major role in foam cell formation, although prior oxidation of the particles is required. Recent studies, however, have provided considerable evidence to indicate that CMRs (chylomicron remnants), which carry dietary lipids in the blood, induce foam cell formation without oxidation. We have shown that CMRs are taken up by macrophages and induce accumulation of both triacylglycerol and cholesterol, and that the rate of uptake and amount of lipid accumulated is influenced by the type of dietary fat in the particles. Furthermore, oxidation of CMRs, in striking contrast with LDL, inhibits, rather than enhances, their uptake and induction of lipid accumulation. In addition, the lipid accumulated after exposure of macrophages to CMRs is resistant to efflux, and this may be due to its sequestration in lysosomes. These findings demonstrate that CMRs induce pro-atherogenic changes in macrophages, and that their effects may be modulated by dietary factors including oxidized fats, lipophilic antioxidants and the type of fat present.

Modeling of Turbulent Natural Gas and Biogas Flames of the Delft Jet-in-Hot-Coflow Burner: Effects of Coflow Temperature, Fuel Temperature and Fuel Composition on the Flame Lift-Off Height

The structure of a turbulent non-premixed flame of a biogas fuel in a hot and diluted coflow mimicking moderate and intense low dilution (MILD) combustion is studied numerically. Biogas fuel is obtained by dilution of Dutch natural gas (DNG) with CO2. The results of biogas combustion are compared with those of DNG combustion in the Delft Jet-in-Hot-Coflow (DJHC) burner. New experimental measurements of lift-off height and of velocity and temperature statistics have been made to provide a database for evaluating the capability of numerical methods in predicting the flame structure. Compared to the lift-off height of the DNG flame, addition of 30 % carbon dioxide to the fuel increases the lift-off height by less than 15 %. Numerical simulations are conducted by solving the RANS equations using Reynolds stress model (RSM) as turbulence model in combination with EDC (Eddy Dissipation Concept) and transported probability density function (PDF) as turbulence-chemistry interaction models. The DRM19 reduced mechanism is used as chemical kinetics with the EDC model. A tabulated chemistry model based on the Flamelet Generated Manifold (FGM) is adopted in the PDF method. The table describes a non-adiabatic three stream mixing problem between fuel, coflow and ambient air based on igniting counterflow diffusion flamelets. The results show that the EDC/DRM19 and PDF/FGM models predict the experimentally observed decreasing trend of lift-off height with increase of the coflow temperature. Although more detailed chemistry is used with EDC, the temperature fluctuations at the coflow inlet (approximately 100K) cannot be included resulting in a significant overprediction of the flame temperature. Only the PDF modeling results with temperature fluctuations predict the correct mean temperature profiles of the biogas case and compare well with the experimental temperature distributions.

Catalytic reactions with palladium supported on mesocellular foam : Applications in hydrogenation, isomerization, and C-C bond forming reactions

The major part of this thesis concerns the development of catalytic methodologies based on palladium nanoparticles immobilized on aminopropyl-functionalized siliceous mesocellular foam (Pd0-AmP-MCF). The catalytic activity of the precursor to the nanocatalyst, PdII-AmP-MCF is also covered by this work. In the first part the application of Pd0-AmP-MCF in Suzuki-Miyaura cross-coupling reactions and transfer hydrogenation of alkenes under microwave irradiation is described. Excellent reactivity was observed and a broad range of substrates were tolerated for both transformations. The Pd0-AmP-MCF exhibited high recyclability as well as low metal leaching in both cases. The aim of the second part was to evaluate the catalytic efficiency of the closely related PdII-AmP-MCF for cycloisomerization of various acetylenic acids. The catalyst was able to promote formation of lactones under mild conditions using catalyst loadings of 0.3 - 0.5 mol% at temperatures of up to 50 oC in the presence of Et3N. By adding 1,4-benzoquinone to the reaction, the catalyst could be recycled four times without any observable decrease in the activity. The selective arylation of indoles at the C-2 position using Pd-AmP-MCF and symmetric diaryliodonium salts is presented in the third part. These studies revealed that Pd0-AmP-MCF was more effective than PdII-AmP-MCF for this transformation. Variously substituted indoles as well as diaryliodonium salts were tolerated, giving arylated indoles in high yields within 15 h at 20 - 50 oC in H2O. Only very small amounts of Pd leaching were observed and in this case the catalyst exhibited moderate recyclability. The final part of the thesis describes the selective hydrogenation of the C=C in different α,β-unsaturated systems. The double bond was efficiently hydrogenated in high yields both under batch and continuous-flow conditions. High recyclability and low metal leaching were observed in both cases.

Laboratory performance evaluation of CIR-emulsion and its comparison against CIR-foam test results from Phase III, TR-578

Currently, no standard mix design procedure is available for CIR-emulsion in Iowa. The CIR-foam mix design process developed during the previous phase is applied for CIR-emulsion mixtures with varying emulsified asphalt contents. Dynamic modulus test, dynamic creep test, static creep test and raveling test were conducted to evaluate the short- and long-term performance of CIR-emulsion mixtures at various testing temperatures and loading conditions. A potential benefit of this research is a better understanding of CIR-emulsion material properties in comparison with those of CIR-foam material that would allow for the selection of the most appropriate CIR technology and the type and amount of the optimum stabilization material. Dynamic modulus, flow number and flow time of CIR-emulsion mixtures using CSS-1h were generally higher than those of HFMS-2p. Flow number and flow time of CIR-emulsion using RAP materials from Story County was higher than those from Clayton County. Flow number and flow time of CIR-emulsion with 0.5% emulsified asphalt was higher than CIR-emulsion with 1.0% or 1.5%. Raveling loss of CIR-emulsion with 1.5% emulsified was significantly less than those with 0.5% and 1.0%. Test results in terms of dynamic modulus, flow number, flow time and raveling loss of CIR-foam mixtures are generally better than those of CIR-emulsion mixtures. Given the limited RAP sources used for this study, it is recommended that the CIR-emulsion mix design procedure should be validated against several RAP sources and emulsion types.

Analytical and Experimental Investigation of an Ammonia/Air Opposed Reacting Jet

The point-by-point properties of an ammonia/air opposed-reacting-jet flowfield are described by solving the governing partial differential elliptic equations. Analytical descriptions of the reacting flowfield are compared to experimentally measured profiles of temperature and composition. Calculated distributions of stream function, temperature and fuel mole fraction are also presented. © 1972, Taylor & Francis Group, LLC. All rights reserved.

Jet o campero set

Fondo Margaritainés Restrepo

Instrumentation studies for plasma jet and hypersonic wind tunnel,

"This research was supported by the McDonnell Aircraft Corporation under Contract no. 6140-20 P.O. 7S4899-R."

Approximate solutions to optimum flight trajectories for a turbo-jet powered aircraft,

"Purdue Research Foundation. Research project no. 1255. Project Ae-25. This research was supported by the National Advisory Committee for Aeronautics, Washington, D. C., under Contract no. NAW-6465."

Les armes de jet d’Argilos : catalogue typologique

Quelques sites archéologiques comme Olympie, Stymphalos et Olynthe possèdent respectivement un répertoire faisant l’étude des armes de jet retrouvées durant une série de campagnes de fouilles archéologiques. Parmi ces indexes, figurent fréquemment des pointes de flèche, des balles de fronde et des saurotères (contrepoids de lance ou de javelot) provenant de différentes périodes historiques gréco-romaines. À travers les 20e et 21e siècle de notre ère, des spécialistes comme D. Robinson (1931), A. Snodgrass (1964), H. Baitinger (2001), C. Hagerman (2014) dédièrent une partie de leur expertise pour produire des synthèses sur ces objets jadis négligés. Ainsi, ils parvinrent à créer de grandes encyclopédies commentées composées de projectiles retrouvés en sol grec. À l’aide de ces bases de données, les archéologues militaires sont en mesure d’établir des datations et l’origine prétendue de certains types de projectiles. Jusqu’en 2015, les artéfacts militaires trouvés sur le site archéologique d’Argilos n’avaient jamais fait l’objet d’une étude de synthèse. D’abord, inspiré par de publications semblables, ces projectiles furent soumis à un inventaire sous forme de catalogue. Au total, deux types de balles de fronde en plomb, onze types de pointes de flèche et un type de saurotère furent identifiés. Finalement, ce nouveau contenu fut assujetti à des analyses comparatives avec d’autres sites archéologiques possédant des données similaires. Les conclusions découlant de ces analogies donnèrent naissance à la première typologie des armes de jet argilienne. Certes, les analyses se heurtèrent à certains obstacles, notamment à une compréhension de la quasi-inexistence d'une pointe de flèche typiquement "grecque" et à la confusion systématique quant à la distinction entre un saurotère et une pointe de javelot, voire possiblement un carreau de gastraphétès (une sorte d’arbalète imposante utilisée lors de sièges durant le 4e siècle av. J.-C.). En partie, ceci découle de l'historique d'échanges entre la Grèce et les autres peuples méditerranéens, balkaniques et orientaux. En outre, de nombreuses réformes militaires des périodes archaïque et classique provoquèrent une évolution constante sur les aspects stratégiques et les tactiques militaires. Considérant ces facteurs parmi tant d'autres et le fait qu'Argilos ait été une fondation grecque en territoire thraco-macédonien, la possibilité d'influence "étrangère" devient alors prépondérante sur la typologie des projectiles argiliens publiée dans le présent mémoire. Avec beaucoup d’espoir, nous croyons sans équivoque que ce travail de recherche contribuera grandement non seulement à l’histoire d’Argilos, mais aussi à l’étude des projectiles en Grèce du nord.

Numerical prediction of thermal and dynamic characteristics of a fireinduced ceiling-jet

The aim of this thesis is to test the ability of some correlative models such as Alpert correlations on 1972 and re-examined on 2011, the investigation of Heskestad and Delichatsios in 1978, the correlations produced by Cooper in 1982, to define both dynamic and thermal characteristics of a fire induced ceiling-jet flow. The flow occurs when the fire plume impinges the ceiling and develops in the radial direction of the fire axis. Both temperature and velocity predictions are decisive for sprinklers positioning, fire alarms positions, detectors (heat, smoke) positions and activation times and back-layering predictions. These correlative models will be compared with a 3D numerical simulation software CFAST. For the results comparison of temperature and velocity near the ceiling. These results are also compared with a Computational Fluid Dynamics (CFD) analysis, using ANSYS FLUENT.

Thermal analysis in the drilling of solid rigid foam materials and ex-vivo bovine bones

Bone is a dynamic, highly vascularized tissue with a unique capacity to heal and regenerate without scarring. However, drilling remains a concern in several clinical procedures due to thermal damage of the bone and surrounding tissue. The success of this surgeries is dependent of many factors and also in temperature generation during the drilling bone. When an excessive heat is produced during the drilling, thermal necrosis can occur and the bone suffers injuries. Studies have shown that the increased temperature is directly related with the drilling parameters, particularly, the drill speed, feed-rate, applied force, the depth of cut, the geometry of the drill bit, the use or not of a cooling system and also the type of bone.

Foam rolling for delayed-onset muscle soreness and recovery of dynamic performance measures

Context: After an intense bout of exercise, foam rolling is thought to alleviate muscle fatigue and soreness (ie, delayed-onset muscle soreness [DOMS]) and improve muscular performance. Potentially, foam rolling may be an effective therapeutic modality to reduce DOMS while enhancing the recovery of muscular performance. Objective: To examine the effects of foam rolling as a recovery tool after an intense exercise protocol through assessment of pressure-pain threshold, sprint time, change-of-direction speed, power, and dynamic strength-endurance. Design: Controlled laboratory study. Setting: University laboratory. Patients or Other Participants: A total of 8 healthy, physically active males (age = 22.1 ± 2.5 years, height = 177.0 ± 7.5 cm, mass = 88.4 ± 11.4 kg) participated. Intervention(s): Participants performed 2 conditions, separated by 4 weeks, involving 10 sets of 10 repetitions of back squats at 60% of their 1-repetition maximum, followed by either no foam rolling or 20 minutes of foam rolling immediately, 24, and 48 hours postexercise. Main Outcome Measure(s): Pressure-pain threshold, sprint speed (30-m sprint time), power (broad-jump distance), change-of-direction speed (T-test), and dynamic strength-endurance. Results: Foam rolling substantially improved quadriceps muscle tenderness by a moderate to large amount in the days after fatigue (Cohen d range, 0.59 to 0.84). Substantial effects ranged from small to large in sprint time (Cohen d range, 0.68 to 0.77), power (Cohen d range, 0.48 to 0.87), and dynamic strength-endurance (Cohen d = 0.54). Conclusions: Foam rolling effectively reduced DOMS and associated decrements in most dynamic performance measures.