Evaluating fault tolerance on asymmetric multicore systems-on-chip using iso-metrics

The end of Dennard scaling has promoted low power consumption into a firstorder concern for computing systems. However, conventional power conservation schemes such as voltage and frequency scaling are reaching their limits when used in performance-constrained environments. New technologies are required to break the power wall while sustaining performance on future processors. Low-power embedded processors and near-threshold voltage computing (NTVC) have been proposed as viable solutions to tackle the power wall in future computing systems. Unfortunately, these technologies may also compromise per-core performance and, in the case of NTVC, xreliability. These limitations would make them unsuitable for HPC systems and datacenters. In order to demonstrate that emerging low-power processing technologies can effectively replace conventional technologies, this study relies on ARM’s big.LITTLE processors as both an actual and emulation platform, and state-of-the-art implementations of the CG solver. For NTVC in particular, the paper describes how efficient algorithm-based fault tolerance schemes preserve the power and energy benefits of very low voltage operation.

DEX: self-healing expanders

N-linked glycosylation supports cross-talk between receptor tyrosine kinases and androgen receptor

Prostate cancer is the second most common cause of cancer-associated deaths in men and signalling via a transcription factor called androgen receptor (AR) is an important driver of the disease. Androgen treatment is known to affect the expression and activity of other oncogenes including receptor tyrosine kinases (RTKs). In this study we report that AR-positive prostate cancer cell-lines express 50% higher levels of enzymes in the hexosamine biosynthesis pathway (HBP) than AR-negative prostate cell-lines. HBP produces hexosamines that are used by endoplasmic reticulum and golgi enzymes to glycosylate proteins targeted to plasma-membrane and secretion. Inhibition of O-linked glycosylation by ST045849 or N-linked glycosylation with tunicamycin decreased cell viability by 20%. In addition, tunicamycin inhibited the androgen-induced expression of AR target genes KLK3 and CaMKK2 by 50%. RTKs have been shown to enhance AR activity and we used an antibody array to identify changes in the phosphorylation status of RTKs in response to androgen stimulation. Hormone treatment increased the activity of Insulin like Growth Factor 1-Receptor (IGF-1R) ten-fold and this was associated with a concomitant increase in the N-linked glycosylation of the receptor, analyzed by lectin enrichment experiments. Glycosylation is known to be important for the processing and stability of RTKs. Inhibition of N-linked glycosylation resulted in accumulation of IGF-1R pro-receptor with altered mobility as shown by immunoprecipitation. Confocal imaging revealed that androgen induced plasma-membrane localization of IGF-1R was blocked by tunicamycin. In conclusion we have established that the glycosylation of IGF-1R is necessary for the full activation of the receptor in response to androgen treatment and that perturbing this process can break the feedback loop between AR and IGF-1R activation in prostate cells. Achieving similar results selectively in a clinical setting will be an important challenge in the future.

Comprehensive profiling and localisation of the matrix metalloproteinases in urothelial carcinoma

The matrix metalloproteinases (MMPs) are endopeptidases which break down the extracellular matrix and regulate cytokine and growth factor activity. Several MMPs have been implicated in the promotion of invasion and metastasis in a broad range of tumours including urothelial carcinoma. In this study, RNA from 132 normal bladder and urothelial carcinoma specimens was profiled for each of the 24 human MMPs, the four endogenous tissue inhibitors of MMPs (TIMPs) and several key growth factors and their receptors using quantitative real time RT-PCR. Laser capture microdissection (LCM) of RNA from 22 tumour and 11 normal frozen sections was performed allowing accurate RNA extraction from either stromal or epithelial compartments. This study confirms the over expression in bladder tumour tissue of well-documented MMPs and highlights a range of MMPs which have not previously been implicated in the development of urothelial cancer. In summary, MMP-2, MT1-MMP and the previously unreported MMP-28 were very highly expressed in tumour samples while MMPs 1, 7, 9, 11, 15, 19 and 23 were highly expressed. There was a significant positive correlation between transcript expression and tumour grade for MMPs 1, 2, 8, 10, 11, 12, 13, 14, 15 and 28 (P < 0.001). At the same confidence interval, TIMP-1 and TIMP-3 also correlated with increasing tumour grade. LCM revealed that most highly expressed MMPs are located primarily within the stromal compartment except MMP-13 which localised to the epithelial compartment. This work forms the basis for further functional studies, which will help to confirm the MMPs as potential diagnostic and therapeutic targets in early bladder cancer.

Characterisation of the performance of sustainable grout containing bentonite for geotechnical applications

The grouts used in sealing or backfilling boreholes should ideally be selected to be compatible with the insitu field instruments installed in the borehole and also be engineered to match closely the geotechnical properties of the parent soils. A stable grout can be made using cement with various proportions of bentonite. The grout stability is very important during both the liquid and set conditions. The liquid grout fluidity should be as viscous as possible to avoid segregation, yet fluid enough to be easily pumpable and fill voids and over-break in the borehole. This paper investigates the effect of bentonite on the fresh and rheological properties of cement-based grouts in order to develop a stable grout to be used in these geotechnical situations. These properties were evaluated by the mini-slump flow, marsh cone flow time, Lombardi plate cohesion meter, static bleeding, yield stress and plastic viscosity values. Additionally, the compressive strength at 3 days, 7 days and 28 days were also investigated. The key parameters investigated were the dosages of bentonite and water-to-binder ratio (W/B). Test results showed that the dosage of bentonite had a significant effect on the fluidity, rheological properties and compressive strength of grout. The increase in the dosage of bentonite led to increasing the values of flow time, plate cohesion meter, yield stress and plastic viscosity, and reducing the mini-slump results, the static bleeding and the compressive strength at 3 days, 7 days and 28 days. Conversely, the increase in W/B led to decreasing the values of flow time, plate cohesion meter, yield stress, and plastic viscosity and the compressive strength, while increasing the mini-slump results and bleeding. Some recommendations for suitable mix proportions for use in soil boreholes are made.

Variations in the Processing of DNA Double-Strand Breaks Along 60-MeV Therapeutic Proton Beams

PURPOSE: To investigate the variations in induction and repair of DNA damage along the proton path, after a previous report on the increasing biological effectiveness along clinically modulated 60-MeV proton beams.

METHODS AND MATERIALS: Human skin fibroblast (AG01522) cells were irradiated along a monoenergetic and a modulated spread-out Bragg peak (SOBP) proton beam used for treating ocular melanoma at the Douglas Cyclotron, Clatterbridge Centre for Oncology, Wirral, Liverpool, United Kingdom. The DNA damage response was studied using the 53BP1 foci formation assay. The linear energy transfer (LET) dependence was studied by irradiating the cells at depths corresponding to entrance, proximal, middle, and distal positions of SOBP and the entrance and peak position for the pristine beam.

RESULTS: A significant amount of persistent foci was observed at the distal end of the SOBP, suggesting complex residual DNA double-strand break damage induction corresponding to the highest LET values achievable by modulated proton beams. Unlike the directly irradiated, medium-sharing bystander cells did not show any significant increase in residual foci.

CONCLUSIONS: The DNA damage response along the proton beam path was similar to the response of X rays, confirming the low-LET quality of the proton exposure. However, at the distal end of SOBP our data indicate an increased complexity of DNA lesions and slower repair kinetics. A lack of significant induction of 53BP1 foci in the bystander cells suggests a minor role of cell signaling for DNA damage under these conditions.

Breaking and Entering: Examining the role of stress and aerial exposure in predator-prey relationships between the common shore crab (Carcinus maenas) and cultivated blue mussels (Mytilus edulis).

During benthic cultivation Mytilus edulis (blue mussels) are subject to predation pressure from a number of predators including Carcinus maenas (shore crabs). This predator can be responsible for substantial losses of mussels from the fishery and a full understanding of the predator–prey relationship between M. edulis and C. maenas is required to ensure attempts that reduce predatory pressure and subsequent commercial loss are successful. Whilst much work has examined the prey–predator size relationships between C. maenas and M. edulis, far less research has investigated how stress, such as periods of extended aerial exposure, may affect these relationships. We tested whether profit in terms of calories gained by crabs consuming mussels stressed by aerial exposure for 48 h differed from that of mussels at ambient conditions and whether being stressed affected the mussel's likelihood of predation. We also tested whether the size relationship between predators and their prey differed when mussels were stressed. We found that the profitability of prey (calories gained per second of handling time) did not vary between stressed and unstressed mussels. Handling times for stressed and unstressed mussels were similar, even when crabs were presented with mussels of the maximum size that they are able to consume. Small crabs were more likely to reject a mussel of preferred size if it was unstressed, suggesting that crabs may be able to assess that these mussels would require extra effort to break into and consume. Our findings suggest that the predator–prey relationship between mussels and crabs is not altered when mussels are stressed. C. maenas remains a voracious predator and regardless of the condition of mussels laid on commercial beds there is a need to control this predator in attempt to reduce losses in the benthic fishery.

Outlier SNP markers reveal fine-scale genetic structuring across European hake populations (Merluccius merluccius)

Shallow population structure is generally reported for most marine fish and explained as a consequence of high dispersal, connectivity and large population size. Targeted gene analyses and more recently genome-wide studies have challenged such view, suggesting that adaptive divergence might occur even when neutral markers provide genetic homogeneity across populations. Here, 381 SNPs located in transcribed regions were used to assess large- and fine-scale population structure in the European hake (Merluccius merluccius), a widely distributed demersal species of high priority for the European fishery. Analysis of 850 individuals from 19 locations across the entire distribution range showed evidence for several outlier loci, with significantly higher resolving power. While 299 putatively neutral SNPs confirmed the genetic break between basins (F(CT) = 0.016) and weak differentiation within basins, outlier loci revealed a dramatic divergence between Atlantic and Mediterranean populations (F(CT) range 0.275-0.705) and fine-scale significant population structure. Outlier loci separated North Sea and Northern Portugal populations from all other Atlantic samples and revealed a strong differentiation among Western, Central and Eastern Mediterranean geographical samples. Significant correlation of allele frequencies at outlier loci with seawater surface temperature and salinity supported the hypothesis that populations might be adapted to local conditions. Such evidence highlights the importance of integrating information from neutral and adaptive evolutionary patterns towards a better assessment of genetic diversity. Accordingly, the generated outlier SNP data could be used for tackling illegal practices in hake fishing and commercialization as well as to develop explicit spatial models for defining management units and stock boundaries.

Time-lapse monitoring of fluid induced geophysical property variations within an unstable earthwork using P-wave refraction

A significant portion of the UK’s transportation system relies on a network of geotechnical earthworks (cuttings and embankments) that were constructed more than 100 years ago, whose stability is affected by the change in precipitation patterns experienced over the past few decades. The vulnerability of these structures requires a reliable, cost- and time-effective monitoring of their geomechanical condition. We have assessed the potential application of P-wave refraction for tracking the seasonal variations of seismic properties within an aged clay-filled railway embankment, located in southwest England. Seismic data were acquired repeatedly along the crest of the earthwork at regular time intervals, for a total period of 16 months. P-wave first-break times were picked from all available recorded traces, to obtain a set of hodocrones referenced to the same spatial locations, for various dates along the surveyed period of time. Traveltimes extracted from each acquisition were then compared to track the pattern of their temporal variability. The relevance of such variations over time was compared with the data experimental uncertainty. The multiple set of hodocrones was subsequently inverted using a tomographic approach, to retrieve a time-lapse model of VPVP for the embankment structure. To directly compare the reconstructed VPVP sections, identical initial models and spatial regularization were used for the inversion of all available data sets. A consistent temporal trend for P-wave traveltimes, and consequently for the reconstructed VPVP models, was identified. This pattern could be related to the seasonal distribution of precipitation and soil-water content measured on site.

Effect of high pressure processing in combination with Weissella viridescens as a protective culture against Listeria monocytogenes in ready-to-eat salads of different pH

This study explored the effect of HPP (400 MPa/1 min) and a Weissella viridescens protective culture, alone or in conjunction, against Listeria monocytogenes in ready-to-eat (RTE) salads with different pH values (4.32 and 5.59) during storage at 4 and 12 °C. HPP was able to reduce the counts of the pathogen after treatment achieving approximately a 4.0 and 1.5 log CFU/g reduction in the low and higher pH RTE salad, respectively. However, L. monocytogenes was able to recover and grow during subsequent storage. W. viridescens grew in both RTE salads at both storage temperatures, with HPP resulting in only a small immediate reduction of W. viridescens ranging from 0.50 to 1.2 log CFU/g depending on the pH of the RTE salad. For the lower pH RTE salad, the protective culture was able to gradually reduce the L. monocytogenes counts during storage whereas for the higher pH RTE salad in some cases it delayed growth significantly or exerted a bacteriostatic effect. exerted a bacteriostatic effect. The results revealed that the increased storage temperature led to an increase in the inactivation/inhibition of L. monocytogenes in the presence of W. viridescens. The combination of HPP and W. viridescens is a promising strategy to control L. monocytogenes and can increase safety even when a break in the chill chain occurs.

Trends in Approval Times for Genetically Engineered Crops in the United States and the European Union

Genetically engineered (GE) crops are subject to regulatory oversight to ensure their safety for humans and the environment. Their approval in the European Union (EU) starts with an application in a given Member State followed by a scientific step (risk assessment), and ends with a political decision-making step (risk management); and in the United States (US) it starts with a scientific (field trial) step and ends with a ‘bureaucratic’ decision-making step. We investigated trends for the time taken for these steps and the overall time taken for approving GE crops in the US and the EU (traders in these commodities). Results show that from 1996-2015 the overall time trend for approval in the EU decreased and then flattened off, with an overall mean completion-time of 1,763 days. In the US in 1998 there was a break in the trend of the overall approval time: Initially, from 1988 until 1997 the trend decreased with a mean approval time of 1,321 days; from 1998-2015, the trend almost stagnated with a mean approval time of 2,467 days.

High-resolution seismic reflection investigation of gas accumulation and seepage in the tidal channels of the Ria of Aveiro barrier lagoon (Portugal)

O metano é um gás de estufa potente e uma importante fonte de energia. A importância global e impacto em zonas costeiras de acumulações e escape de gás metano são ainda pouco conhecidas. Esta tese investiga acumulações e escape de gás em canais de maré da Ria de Aveiro com dados de cinco campanhas de reflexão sísmica de alta resolução realizadas em 1986, 1999, 2002 e 2003. Estas incluem três campanhas de Chirp (RIAV99, RIAV02 e RIAV02A) e duas campanhas de Boomer (VOUGA86 e RIAV03). O processamento dos dados de navegação incluíram filtros de erros, correcções de sincronização de relógios de sistemas de aquisição de dados, ajuste de “layback” e estimativa da posição de “midpoint”. O processamento do sinal sísmico consistiu na correcção das amplitudes, remoção de ruído do tipo “burst”, correcções estáticas, correcção do “normal move-out”, filtragem passabanda, desconvolução da assinatura e migração Stolt F-K. A análise da regularidade do trajecto de navegação, dos desfasamentos entre horizontes e dos modelos de superfícies foi utilizada para controlo de qualidade, e permitiu a revisão e melhoria dos parâmetros de processamento. A heterogeneidade da cobertura sísmica, da qualidade do sinal, da penetração e da resolução, no seu conjunto constrangeram o uso dos dados a interpretações detalhadas, mas locais, de objectos geológicos da Ria. É apresentado um procedimento para determinar a escolha de escalas adequadas para modelar os objectos geológicos, baseado na resolução sísmica, erros de posicionamento conhecidos e desfasamentos médios entre horizontes. As evidências de acumulação e escape de gás na Ria de Aveiro incluem turbidez acústica, reflexões reforçadas, cortinas acústicas, domas, “pockmarks” e alinhamentos de “pockmarks” enterradas, horizontes perturbados e plumas acústicas na coluna de água (flares). A estratigrafia e a estrutura geológica controlam a distribuição e extensão das acumulações e escape de gás. Ainda assim, nestes sistemas de baixa profundidade de água, as variações da altura de maré têm um impacto significativo na detecção de gás com métodos acústicos, através de alterações nas amplitudes originais de reflexões reforçadas, turbidez acústica e branqueamento acústico em zonas com gás. Os padrões encontrados confirmam que o escape de bolhas de gás é desencadeado pela descida da maré. Há acumulações de gás em sedimentos Holocénicos e no substrato de argilas e calcários do Mesozóico. Evidências directas de escape de gás em sondagens em zonas vizinhas, mostraram gás essencialmente biogénico. A maioria do gás na área deve ter sido gerado em sedimentos lagunares Holocénicos. No entanto, a localização e geometria de estruturas de escape de fluidos em alguns canais de maré, seguem o padrão de fracturas do substrato Mesozóico, indicando uma possível fonte mais profunda de gás e que estas fracturas funcionam como condutas preferenciais de migração dos fluidos e exercem um controlo estrutural na ocorrência de gás na Ria.

Diversidade linguística e educação para um futuro sustentável: que potencialidades nos primeiros anos de escolaridade?

Este estudo pretende analisar as relações entre a educação para a sustentabilidade e a sensibilização à diversidade linguística e cultural no currículo dos primeiros anos de escolaridade através do desenvolvimento de um projeto de intervenção pedagógico-didática. Para tal, refletiu-se sobre as noções de educação para o desenvolvimento sustentável e de sensibilização à diversidade linguística e cultural, explicitando o modo como se podem cruzar. Com este enquadramento, e numa lógica de investigação-ação, desenvolveuse o projeto de intervenção “Do meu mundo vejo o outro e o seu mundo”, em 21 sessões, numa turma do 4º ano do 1º Ciclo do Ensino Básico, de forma colaborativa com a respetiva professora titular, numa escola do distrito de Aveiro, durante o ano letivo de 2008/2009. Recolheram-se dados através da observação direta do(a)s aluno(a)s durante as sessões e de inquéritos por questionário e por entrevista ao(à)s aluno(a)s e à professora participante. Os dados recolhidos durante as sessões foram analisados com recurso à Escala de nível de envolvimento de Leuven (Laevers, 1994) e os inquéritos por questionário e entrevista foram alvo de uma análise estatística descritiva e de uma análise de conteúdo. Identificaram-se os efeitos do projeto no(a)s aluno(a)s em termos do seu nível de envolvimento nas atividades e do desenvolvimento das suas atitudes, conhecimentos e capacidades. A partir das vozes dos participantes, analisouse ainda a apreciação que realizaram do projeto na sua globalidade. Os resultados da análise apontam no sentido de que o projeto de intervenção desenvolvido contribuiu para: ajudar a derrubar barreiras disciplinares entre as àreas do currículo; justificar a necessidade de contemplar a sensibilização à diversidade linguística e cultural em processos de educação para o desenvolvimento sustentável; desenvolver materiais didáticos diversificados construídos numa lógica interdisciplinar, reconhecidos pela professora como inovadores e importantes para aprendizagens significativas e contextualizadas; transformar atitudes do(a)s aluno(a)s face à diversidade e à sustentabilidade, na preparação para uma cidadania planetária; e desenvolver no(a)s aluno(a)s uma consciência sistémica evidenciada na capacidade de relacionamento do global e do local em temas de diferentes áreas do conhecimento. Este estudo apresenta um conjunto de argumentos para a integração do tratamento da diversidade linguística e cultural no quadro de uma educação para um futuro mais sustentável nos primeiros anos de escolaridade, pela consideração de quatro grandes preocupações educativas: educar para compreender o mundo, educar para agir no mundo; educar para conviver com os outros e educar para o nunca-mais.

Qualidade e optimização do desmonte de maciços rochosos em geotecnia mineira

A perfuração é uma das operações envolvidas no desmonte de rocha com explosivos. A forma como esta operação é executada é determinante para o sucesso do desmonte. Quando é realizada correctamente o desmonte produz superfícies limpas com o mínimo de sobrescavação e perturbação. A selecção das ferramentas de perfuração é um dos factores preponderantes para os custos do desmonte de maciços rochosos. O objectivo deste trabalho é demonstrar a interdependência entre os parâmetros petrofísicos, geotécnicos e geomecânicos do maciço rochoso e as tecnologias de perfuração de forma a optimizar tanto técnica como economicamente. A forma como a perfuração é executada é determinante para a boa fragmentação do maciço rochoso. Este estudo irá centrar-se na perfurabilidade do maciço, linearidade dos furos, rendimento e desgaste das ferramentas de perfuração e desenvolvimento de metodologias do ciclo de perfuração. Neste trabalho, discute-se a importância de uma abordagem integrativa para fins de geoengenhara mineira em que foi aplicada a técnica de amostragem linear em superfícies expostas do maciço num ambiente de uma exploração granítica. As áreas seleccionadas para este estudo — Pedreira de Serdedelo (Ribeira, Ponte de Lima) e pedreira do Fojo (Ferreira, Paredes de Coura), NW de Portugal — estão situadas nas proximidades de falhas geológicas regionais. Em todo os casos de estudo foram desenvolvidos numa plataforma SIG usando as seguintes ferramentas: cartografia geo-aplicada, técnicas de geologia estrutural, da geotecnia e da geomecânica mineiras e avaliação de geotecnologias. Esta abordagem leva-nos a compreender a relevância da heterogeneidade do maciço rochoso para o dimensionamento da exploração a diferentes escalas. O controlo geomecânico do desmonte do maciço rochoso através de uma perfuração alinhada é salientado com o intuito de uma abordagem de geoengenharia integrada nos maciços rochosos.

Propriedades intrínsecas e de processamento de termoplásticos elastoméricos incorporando borracha de pneu reciclada

O trabalho apresentado tem por objetivo contribuir para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental. A abordagem adotada para a concretização deste objetivo consiste na incorporação de borracha de pneus em formulações de base termoplástica e elastomérica (TPE), adequadas ao processo de moldação por injeção. São desenvolvidos estudos sobre a morfologia, propriedades mecânicas, térmicas e reológicas das ligas poliméricas à base de granulado de borracha de pneu (GTR). A falta de adesão entre o GTR e a matriz polimérica leva à degradação das propriedades mecânicas dos materiais obtidos. A estratégia explorada passa pela utilização de um elastómero para promover o encapsulamento do GTR e, desta forma, procurar obter ligas com propriedades mecânicas características de um TPE. São analisadas ligas ternárias (TPEGTR) compostas por polipropileno (PP) de elevada fluidez, GTR e elastómero virgem. O efeito da presença de diferentes elastómeros nas ligas é analisado neste trabalho: um elastómero de etilenopropileno- dieno (EPDM), e um novo elastómero de etileno-propileno (EPR) obtido por catálise metalocénica. O estudo da morfologia das ligas obtidas mostra haver interação entre os materiais, sendo possível inferir a viabilidade da estratégia adotada para promover a adesão do GTR. A incorporação de elastómero promove o aumento da resistência ao impacto e da extensão na rotura nas ligas, o que é atribuído, fundamentalmente, ao encapsulamento do GTR e ao aumento da tenacidade da matriz termoplástica. Com o objetivo de avaliar a influência da estrutura cristalina das ligas TPEGTR no seu comportamento mecânico, procede-se à análise do processo de cristalização sob condições isotérmicas e não isotérmicas. Neste estudo, é avaliado o efeito da presença dos materiais que constituem a fase elastomérica na cinética de cristalização. Para cada uma das ligas desenvolvidas, recorre-se ao modelo de Avrami para avaliar o efeito da temperatura no mecanismo de nucleação, na morfologia das estruturas cristalinas e na taxa de cristalização. Recorre-se à reometria capilar para estudar, sob condições estacionárias, o comportamento reológico das ligas TPEGTR. O modelo de Cross-WLF é utilizado para avaliar o comportamento reológico de todos os materiais, obtendo-se resultados similares àqueles obtidos experimentalmente. O comportamento reológico dos polímeros PP, EPR e EPDM é do tipo reofluidificante, tendo o EPR um comportamento reológico similar ao do PP e o EPDM um comportamento reo-fluidificante mais pronunciado. Em todas as ligas analisadas o comportamento reológico revela-se do tipo reo-fluidificante, sendo que a presença de GTR promove o aumento da viscosidade. Os parâmetros obtidos do modelo de Cross-WLF são utilizados para realizar a simulação da etapa de injeção recorrendo a um software comercial. Os resultados obtidos são validados experimentalmente pelo processo de moldação por injeção, evidenciando uma boa adequabilidade da aplicação deste modelo a estas ligas. O trabalho desenvolvido sobre ligas TPEGTR, constitui um contributo para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental.