Collection effects on close pararell bare tethers

We review previously published results, and present new results, on the way current to a cylindrical probe drops below the orbital-motion-limited (OML) value for probe cross-sections too large or concave. Results on size and shape effects arise from unrelated behavior in the near and far potential field, and apply to a general cross-section, which can be characterised by radius Req and perimeter peij of equivalent circles. These results are used to discuss collection interference among two or more parallel bare tethers when brought from far away to contact.

Supercritical Steam power cycle for Line-Focus Solar Power Plants

The supercritical Rankine power cycle offers a net improvement in plant efficiency compared with a subcritical Rankine cycle. For fossil power plants the minimum supercritical steam turbine size is about 450MW. A recent study between Sandia National Laboratories and Siemens Energy, Inc., published on March 2013, confirmed the feasibility of adapting the Siemens turbine SST-900 for supercritical steam in concentrated solar power plants, with a live steam conditions 230-260 bar and output range between 140-200 MWe. In this context, this analysis is focused on integrating a line-focus solar field with a supercritical Rankine power cycle. For this purpose two heat transfer fluids were assessed: direct steam generation and molten salt Hitec XL. To isolate solar field from high pressure supercritical water power cycle, an intermediate heat exchanger was installed between linear solar collectors and balance of plant. Due to receiver selective coating temperature limitations, turbine inlet temperature was fixed 550ºC. The design-point conditions were 550ºC and 260 bar at turbine inlet, and 165 MWe Gross power output. Plant performance was assessed at design-point in the supercritical power plant (between 43-45% net plant efficiency depending on balance of plantconfiguration), and in the subcritical plant configuration (~40% net plant efficiency). Regarding the balance of plant configuration, direct reheating was adopted as the optimum solution to avoid any intermediate heat exchanger. One direct reheating stage between high pressure turbine and intermediate pressure turbine is the common practice; however, General Electric ultrasupercritical(350 bar) fossil power plants also considered doubled-reheat applications. In this study were analyzed heat balances with single-reheat, double-reheat and even three reheating stages. In all cases were adopted the proper reheating solar field configurations to limit solar collectors pressure drops. As main conclusion, it was confirmed net plant efficiency improvements in supercritical Rankine line-focus (parabolic or linear Fresnel) solar plant configurations are mainly due to the following two reasons: higher number of feed-water preheaters (up to seven)delivering hotter water at solar field inlet, and two or even three direct reheating stages (550ºC reheating temperature) in high or intermediate pressure turbines. However, the turbine manufacturer should confirm the equipment constrains regarding reheating stages and number of steam extractions to feed-water heaters.

The influence of axial microgravity on the breakage of axisymmetric slender liquid bridges

The dynamics of inviscid, axisymmetric liquid bridges permits a simplified treatment if the bridge is long enough. Under such condition the evolution of the liquid zone is satisfactorily explained through a non-linear one-dimensional model. In the case of breaking, the one-dimensional model fails when the neck radius of the liquid column is close to zero; however, the model allows the calculation of the time variation of the liquid-bridge interface as well as of the fluid velocity field and, because the last part of the evolution is not needed, the overall results such as the breaking time and the volume of each of the two drops resulting after breakage can be calculated. In this paper numerical results concerning the behavior of clinical liquid bridges subjected to a small axial gravitational field are presented.

Numerical and experimental study of the dynamics of axisymmetric slender liquid bridges

A one-dimensional inviscid slice model has been used to study numerically the influence of axial microgravity on the breaking of liquid bridges having a volume close to that of gravitationless minimum volume stability limit. Equilibrium shapes and stability limits have been obtained as well as the dependence of the volume of the two drops formed after breaking on both the length and the volume of the liquid bridge. The breaking process has also been studied experimentally. Good agreement has been found between theory and experiment for neutrally buoyant systems

The influence of gravity on the solidifcation of a drop

In this paper the influence of gravity on the solidification of a drop formed at the end of a rod is analyzed. Although similar studies (but ignoring gravity effects) already exist, a theoretical analysis including gravity effects allows one to improve the experimental procedure to measure on Earth relevant properties of crystals (mainly the receding contact angle <£,) which are of importance in shaped crystal growth processes. One of the main results here obtained are the shapes of the sohdified drops, which are strongly dependent on the value of <#>,. Therefore, fitting theoretical shapes to experimental ones is a wav to perform accurate measurements of <^.

Transmitter-side antennas correlation in SVD-assisted MIMO systems

MIMO techniques allow increasing wireless channel performance by decreasing the BER and increasing the channel throughput and in consequence are included in current mobile communication standards. MIMO techniques are based on benefiting the existence of multipath in wireless communications and the application of appropriate signal processing techniques. The singular value decomposition (SVD) is a popular signal processing technique which, based on the perfect channel state information (PCSI) knowledge at both the transmitter and receiver sides, removes inter-antenna interferences and improves channel performance. Nevertheless, the proximity of the multiple antennas at each front-end produces the so called antennas correlation effect due to the similarity of the various physical paths. In consequence, antennas correlation drops the MIMO channel performance. This investigation focuses on the analysis of a MIMO channel under transmitter-side antennas correlation conditions. First, antennas correlation is analyzed and characterized by the correlation coefficients. The analysis describes the relation between antennas correlation and the appearance of predominant layers which significantly affect the channel performance. Then, based on the SVD, pre- and post-processing is applied to remove inter-antenna interferences. Finally, bit- and power allocation strategies are applied to reach the best performance. The resulting BER reveals that antennas correlation effect diminishes the channel performance and that not necessarily all MIMO layers must be activated to obtain the best performance.

Stability limits of minimum volume and breaking axisymmetric liquid bridges between unequal disks

This paper deals with the stability limits of minimum volume and the breaking of axisymmetric liquid columns held by capillary forces between two concentric,circular solid disk of different radii. The problem has been analyzed both theoreti-cally and experimentally. A theoretical analysis concerning the breaking of liquid bridges has been performed by using a one-dimensional slice model already used in liquid bridge problems. Experiments have been carried out by using milli-metric liquid bridges, and minimum volume stability limits as well as the volumes of the drops resulting after breaking have been measured for a large number of liquid bridge configurations. Experimental results being in agreement with theoretical prediction.

Selected topics in the Hydrodynamics of floating offshore wind turbines: heave damping and second order surge motions

La Energía eléctrica producida mediante tecnología eólica flotante es uno de los recursos más prometedores para reducir la dependencia de energía proveniente de combustibles fósiles. Esta tecnología es de especial interés en países como España, donde la plataforma continental es estrecha y existen pocas áreas para el desarrollo de estructuras fijas. Entre los diferentes conceptos flotantes, esta tesis se ha ocupado de la tipología semisumergible. Estas plataformas pueden experimentar movimientos resonantes en largada y arfada. En largada, dado que el periodo de resonancia es largo estos puede ser inducidos por efectos de segundo orden de deriva lenta que pueden tener una influencia muy significativa en las cargas en los fondeos. En arfada las fuerzas de primer orden pueden inducir grandes movimientos y por tanto la correcta determinación del amortiguamiento es esencial para la analizar la operatividad de la plataforma. Esta tesis ha investigado estos dos efectos, para ello se ha usado como caso base el diseño de una plataforma desarrollada en el proyecto Europeo Hiprwind. La plataforma se compone de 3 columnas cilíndricas unidas mediante montantes estructurales horizontales y diagonales, Los cilindros proporcionan flotabilidad y momentos adrizante. A la base de cada columna se le ha añadido un gran “Heave Plate” o placa de cierre. El diseño es similar a otros diseños previos (Windfloat). Se ha fabricado un modelo a escala de una de las columnas para el estudio detallado del amortiguamiento mediante oscilaciones forzadas. Las dimensiones del modelo (1m diámetro en la placa de cierre) lo hacen, de los conocidos por el candidato, el mayor para el que se han publicado datos. El diseño del cilindro se ha realizado de tal manera que permite la fijación de placas de cierre planas o con refuerzo, ambos modelos se han fabricado y analizado. El modelo con refuerzos es una reproducción exacta del diseño a escala real incluyendo detalles distintivos del mismo, siendo el más importante la placa vertical perimetral. Los ensayos de oscilaciones forzadas se han realizado para un rango de frecuencias, tanto para el disco plano como el reforzado. Se han medido las fuerzas durante los ensayos y se han calculado los coeficientes de amortiguamiento y de masa añadida. Estos coeficientes son necesarios para el cálculo del fondeo mediante simulaciones en el dominio del tiempo. Los coeficientes calculados se han comparado con la literatura existente, con cálculos potenciales y por ultimo con cálculos CFD. Para disponer de información relevante para el diseño estructural de la plataforma se han medido y analizado experimentalmente las presiones en la parte superior e inferior de cada placa de cierre. Para la correcta estimación numérica de las fuerzas de deriva lenta en la plataforma se ha realizado una campaña experimental que incluye ensayos con modelo cautivo de la plataforma completa en olas bicromaticas. Pese a que estos experimentos no reproducen un escenario de oleaje realista, los mismos permiten una verificación del modelo numérico mediante la comparación de fuerzas medidas en el modelo físico y el numérico. Como resultados de esta tesis podemos enumerar las siguientes conclusiones. 1. El amortiguamiento y la masa añadida muestran una pequeña dependencia con la frecuencia pero una gran dependencia con la amplitud del movimiento. siendo coherente con investigaciones existentes. 2. Las medidas con la placa de cierre reforzada con cierre vertical en el borde, muestra un amortiguamiento significativamente menor comparada con la placa plana. Esto implica que para ensayos de canal es necesario incluir estos detalles en el modelo. 3. La masa añadida no muestra grandes variaciones comparando placa plana y placa con refuerzos. 4. Un coeficiente de amortiguamiento del 6% del crítico se puede considerar conservador para el cálculo en el dominio de la frecuencia. Este amortiguamiento es equivalente a un coeficiente de “drag” de 4 en elementos de Morison cuadráticos en las placas de cierre usadas en simulaciones en el dominio del tiempo. 5. Se han encontrado discrepancias en algunos valores de masa añadida y amortiguamiento de la placa plana al comparar con datos publicados. Se han propuesto algunas explicaciones basadas en las diferencias en la relación de espesores, en la distancia a la superficie libre y también relacionadas con efectos de escala. 6. La presión en la placa con refuerzos son similares a las de la placa plana, excepto en la zona del borde donde la placa con refuerzo vertical induce una gran diferencias de presiones entre la cara superior e inferior. 7. La máxima diferencia de presión escala coherentemente con la fuerza equivalente a la aceleración de la masa añadida distribuida sobre la placa. 8. Las masas añadidas calculadas con el código potencial (WADAM) no son suficientemente precisas, Este software no contempla el modelado de placas de pequeño espesor con dipolos, la poca precisión de los resultados aumenta la importancia de este tipo de elementos al realizar simulaciones con códigos potenciales para este tipo de plataformas que incluyen elementos de poco espesor. 9. Respecto al código CFD (Ansys CFX) la precisión de los cálculos es razonable para la placa plana, esta precisión disminuye para la placa con refuerzo vertical en el borde, como era de esperar dado la mayor complejidad del flujo. 10. Respecto al segundo orden, los resultados, en general, muestran que, aunque la tendencia en las fuerzas de segundo orden se captura bien con los códigos numéricos, se observan algunas reducciones en comparación con los datos experimentales. Las diferencias entre simulaciones y datos experimentales son mayores al usar la aproximación de Newman, que usa únicamente resultados de primer orden para el cálculo de las fuerzas de deriva media. 11. Es importante remarcar que las tendencias observadas en los resultados con modelo fijo cambiarn cuando el modelo este libre, el impacto que los errores en las estimaciones de fuerzas segundo orden tienen en el sistema de fondeo dependen de las condiciones ambientales que imponen las cargas ultimas en dichas líneas. En cualquier caso los resultados que se han obtenido en esta investigación confirman que es necesaria y deseable una detallada investigación de los métodos usados en la estimación de las fuerzas no lineales en las turbinas flotantes para que pueda servir de guía en futuros diseños de estos sistemas. Finalmente, el candidato espera que esta investigación pueda beneficiar a la industria eólica offshore en mejorar el diseño hidrodinámico del concepto semisumergible. ABSTRACT Electrical power obtained from floating offshore wind turbines is one of the promising resources which can reduce the fossil fuel energy consumption and cover worldwide energy demands. The concept is the most competitive in countries, such as Spain, where the continental shelf is narrow and does not provide space for fixed structures. Among the different floating structures concepts, this thesis has dealt with the semisubmersible one. Platforms of this kind may experience resonant motions both in surge and heave directions. In surge, since the platform natural period is long, such resonance can be excited with second order slow drift forces and may have substantial influence on mooring loads. In heave, first order forces can induce significant motion, whose damping is a crucial factor for the platform downtime. These two topics have been investigated in this thesis. To this aim, a design developed during HiPRWind EU project, has been selected as reference case study. The platform is composed of three cylindrical legs, linked together by a set of structural braces. The cylinders provide buoyancy and restoring forces and moments. Large circular heave plates have been attached to their bases. The design is similar to other documented in literature (e.g. Windfloat), which implies outcomes could have a general value. A large scale model of one of the legs has been built in order to study heave damping through forced oscillations. The final dimensions of the specimen (one meter diameter discs) make it, to the candidate’s knowledge, the largest for which data has been published. The model design allows for the fitting of either a plain solid heave plate or a flapped reinforced one; both have been built. The latter is a model scale reproduction of the prototype heave plate and includes some distinctive features, the most important being the inclusion of a vertical flap on its perimeter. The forced oscillation tests have been conducted for a range of frequencies and amplitudes, with both the solid plain model and the vertical flap one. Forces have been measured, from which added mass and damping coefficients have been obtained. These are necessary to accurately compute time-domain simulations of mooring design. The coefficients have been compared with literature, and potential flow and CFD predictions. In order to provide information for the structural design of the platform, pressure measurements on the top and bottom side of the heave discs have been recorded and pressure differences analyzed. In addition, in order to conduct a detailed investigation on the numerical estimations of the slow-drift forces of the HiPRWind platform, an experimental campaign involving captive (fixed) model tests of a model of the whole platform in bichromatic waves has been carried out. Although not reproducing the more realistic scenario, these tests allowed a preliminary verification of the numerical model based directly on the forces measured on the structure. The following outcomes can be enumerated: 1. Damping and added mass coefficients show, on one hand, a small dependence with frequency and, on the other hand, a large dependence with the motion amplitude, which is coherent with previously published research. 2. Measurements with the prototype plate, equipped with the vertical flap, show that damping drops significantly when comparing this to the plain one. This implies that, for tank tests of the whole floater and turbine, the prototype plate, equipped with the flap, should be incorporated to the model. 3. Added mass values do not suffer large alterations when comparing the plain plate and the one equipped with a vertical flap. 4. A conservative damping coefficient equal to 6% of the critical damping can be considered adequate for the prototype heave plate for frequency domain analysis. A corresponding drag coefficient equal to 4.0 can be used in time domain simulations to define Morison elements. 5. When comparing to published data, some discrepancies in added mass and damping coefficients for the solid plain plate have been found. Explanations have been suggested, focusing mainly on differences in thickness ratio and distance to the free surface, and eventual scale effects. 6. Pressures on the plate equipped with the vertical flap are similar in magnitude to those of the plain plate, even though substantial differences are present close to the edge, where the flap induces a larger pressure difference in the reinforced case. 7. The maximum pressure difference scales coherently with the force equivalent to the acceleration of the added mass, distributed over the disc surface. 8. Added mass coefficient values predicted with the potential solver (WADAM) are not accurate enough. The used solver does not contemplate modeling thin plates with doublets. The relatively low accuracy of the results highlights the importance of these elements when performing potential flow simulations of offshore platforms which include thin plates. 9. For the full CFD solver (Ansys CFX), the accuracy of the computations is found reasonable for the plain plate. Such accuracy diminishes for the disc equipped with a vertical flap, an expected result considering the greater complexity of the flow. 10. In regards to second order effects, in general, the results showed that, although the main trend in the behavior of the second-order forces is well captured by the numerical predictions, some under prediction of the experimental values is visible. The gap between experimental and numerical results is more pronounced when Newman’s approximation is considered, making use exclusively of the mean drift forces calculated in the first-order solution. 11. It should be observed that the trends observed in the fixed model test may change when the body is free to float, and the impact that eventual errors in the estimation of the second-order forces may have on the mooring system depends on the characteristics of the sea conditions that will ultimately impose the maximum loads on the mooring lines. Nevertheless, the preliminary results obtained in this research do confirm that a more detailed investigation of the methods adopted for the estimation of the nonlinear wave forces on the FOWT would be welcome and may provide some further guidance for the design of such systems. As a final remark, the candidate hopes this research can benefit the offshore wind industry in improving the hydrodynamic design of the semi-submersible concept.

A multi-scale analysis of transforming agricultural markets in the context of globalization: implications for natural resources, food prices and rural poverty in Latin America

Vivimos una época en la que el mundo se transforma aceleradamente. La globalización está siguiendo un curso imparable, la población mundial así como la población urbana siguen creciendo, y en los países emergentes los ingresos promedios aumentan, resultando en un cambio también acelerado de las dietas y hábitos alimentarios. En conjunto esos factores están causando un aumento fundamental de la demanda de alimentos. Junto con la apertura de los mercados agrícolas, estos procesos han provocado un crecimiento del comercio internacional de alimentos durante la última década. Dado que muchos países de América Latina están dotados de abundancia de recursos naturales, estas tendencias han producido un crecimiento rápido de las exportaciones de bienes primarios desde América Latina al resto del mundo. En sólo 30 años la participación en el mercado agrícola de América Latina casi se ha duplicado, desde 10% en 1980 a 18% en 2010. Este aumento del comercio agrícola ha dado lugar a un debate sobre una serie de cuestiones cruciales relacionadas con los impactos del comercio en la seguridad alimentaria mundial, en el medio ambiente o en la reducción de la pobreza rural en países en desarrollo. Esta tesis aplica un marco integrado para analizar varios impactos relacionados con la transformación de los mercados agrícolas y los mercados rurales debidos a la globalización y, en particular, al progresivo aumento del comercio internacional. En concreto, la tesis aborda los siguientes temas: En primer lugar, la producción mundial de alimentos tendrá que aumentar considerablemente para poder satisfacer la demanda de una población mundial de 9000 millones personas en 2050, lo cual plantea grandes desafíos sobre los sistemas de la producción de alimentos. Alcanzar este logro, sin comprometer la integridad del medio ambiente en regiones exportadoras, es un reto aún mayor. En este contexto, la tesis analiza los efectos de la liberalización del comercio mundial, considerando distintas tecnologías de producción agraria, sobre unos indicadores de seguridad alimentaria en diferentes regiones del mundo y sobre distintos indicadores ambientales, teniendo en cuenta escalas diferentes en América Latina y el Caribe. La tesis utiliza el modelo “International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT)” – un modelo dinámico de equilibrio parcial del sector agrícola a escala global – para modelar la apertura de los mercados agrícolas así como diferentes escenarios de la producción hasta el año 2050. Los resultados del modelo están vinculados a modelos biofísicos para poder evaluar los cambios en la huella hídrica y la calidad del agua, así como para cuantificar los impactos del cambio en el uso del suelo sobre la biodiversidad y los stocks de carbono en 2050. Los resultados indican que la apertura de los mercados agrícolas es muy importante para mejorar la seguridad alimentaria a nivel mundial, sin embargo, produce también presiones ambientales indeseables en algunas regiones de América Latina. Contrastando dos escenarios que consideran distintas modos de producción, la expansión de la tierra agrícola frente a un escenario de la producción más intensiva, se demuestra que las mejoras de productividad son generalmente superiores a la expansión de las tierras agrícolas, desde un punto de vista económico e ambiental. En cambio, los escenarios de intensificación sostenible no sólo hacen posible una mayor producción de alimentos, sino que también generan menos impactos medioambientales que los otros escenarios futuros en todas sus dimensiones: biodiversidad, carbono, emisiones de nitratos y uso del agua. El análisis muestra que hay un “trade-off” entre el objetivo de alcanzar la sostenibilidad ambiental y el objetivo de la seguridad alimentaria, independiente del manejo agrícola en el futuro. En segundo lugar, a la luz de la reciente crisis de los precios de alimentos en los años 2007/08, la tesis analiza los impactos de la apertura de los mercados agrícolas en la transmisión de precios de los alimentos en seis países de América Latina: Argentina, Brasil, Chile, Colombia, México y el Perú. Para identificar las posibles relaciones de cointegración entre los índices de precios al consumidor de alimentos y los índices de precios de agrarios internacionales, sujetos a diferentes grados de apertura de mercados agrícolas en los seis países de América Latina, se utiliza un modelo simple de corrección de error (single equation error correction). Los resultados indican que la integración global de los mercados agrícolas ha dado lugar a diferentes tasas de transmisión de precios en los países investigados. Sobre todo en el corto plazo, las tasas de transmisión dependen del grado de apertura comercial, mientras que en el largo plazo las tasas de transmisión son elevadas, pero en gran medida independientes del régimen de comercio. Por lo tanto, durante un período de shocks de precios mundiales una mayor apertura del comercio trae consigo más inestabilidad de los precios domésticos a corto plazo y la resultante persistencia en el largo plazo. Sin embargo, estos resultados no verifican necesariamente la utilidad de las políticas comerciales, aplicadas frecuentemente por los gobiernos para amortiguar los shocks de precios. Primero, porque existe un riesgo considerable de volatilidad de los precios debido a cambios bruscos de la oferta nacional si se promueve la autosuficiencia en el país; y segundo, la política de proteccionismo asume el riesgo de excluir el país de participar en las cadenas de suministro de alto valor del sector agrícola, y por lo tanto esa política podría obstaculizar el desarrollo económico. Sin embargo, es indispensable establecer políticas efectivas para reducir la vulnerabilidad de los hogares a los aumentos repentinos de precios de alimentos, lo cual requiere una planificación gubernamental precisa con el presupuesto requerido disponible. En tercer lugar, la globalización afecta a la estructura de una economía y, por medios distintos, la distribución de los ingreso en un país. Perú sirve como ejemplo para investigar más profundamente las cuestiones relacionadas con los cambios en la distribución de los ingresos en zonas rurales. Perú, que es un país que está cada vez más integrado en los mercados mundiales, consiguió importantes descensos en la pobreza extrema en sus zonas rurales, pero a la vez adolece de alta incidencia de pobreza moderada y de desigualdad de los ingresos en zonas rural al menos durante el periodo comprendido entre 2004 y 2012. Esta parte de la tesis tiene como objetivo identificar las fuerzas impulsoras detrás de estas dinámicas en el Perú mediante el uso de un modelo de microsimulación basado en modelos de generación de ingresos aplicado a nivel los hogares rurales. Los resultados indican que la fuerza principal detrás de la reducción de la pobreza ha sido el crecimiento económico general de la economía, debido a las condiciones macroeconómicas favorables durante el periodo de estudio. Estos efectos de crecimiento beneficiaron a casi todos los sectores rurales, y dieron lugar a la disminución de la pobreza rural extrema, especialmente entre los agricultores de papas y de maíz. En parte, estos agricultores probablemente se beneficiaron de la apertura de los mercados agrícolas, que es lo que podría haber provocado un aumento de los precios al productor en tiempos de altos precios mundiales de los alimentos. Sin embargo, los resultados también sugieren que para una gran parte de la población más pobre existían barreras de entrada a la hora de poder participar en el empleo asalariado fuera de la agricultura o en la producción de cultivos de alto valor. Esto podría explicarse por la falta de acceso a unos activos importantes: por ejemplo, el nivel de educación de los pobres era apenas mejor en 2012 que en 2004; y también las dotaciones de tierra y de mano de obra, sobre todo de los productores pobres de maíz y patata, disminuyeron entre 2004 y 2012. Esto lleva a la conclusión de que aún hay margen para aplicar políticas para facilitar el acceso a estos activos, que podría contribuir a la erradicación de la pobreza rural. La tesis concluye que el comercio agrícola puede ser un importante medio para abastecer una población mundial creciente y más rica con una cantidad suficiente de calorías. Para evitar adversos efectos ambientales e impactos negativos para los consumidores y de los productores pobres, el enfoque debe centrarse en las mejoras de la productividad agrícola, teniendo en cuenta los límites ambientales y ser socialmente inclusivo. En este sentido, será indispensable seguir desarrollando soluciones tecnológicas que garanticen prácticas de producción agrícola minimizando el uso de recursos naturales. Además, para los pequeños pobres agricultores será fundamental eliminar las barreras de entrada a los mercados de exportación que podría tener efectos indirectos favorables a través de la adopción de nuevas tecnologías alcanzables a través de mercados internacionales. ABSTRACT The world is in a state of rapid transition. Ongoing globalization, population growth, rising living standards and increasing urbanization, accompanied by changing dietary patterns throughout the world, are increasing the demand for food. Together with more open trade regimes, this has triggered growing international agricultural trade during the last decade. For many Latin American countries, which are gifted with relative natural resource abundance, these trends have fueled rapid export growth of primary goods. In just 30 years, the Latin American agricultural market share has almost doubled from 10% in 1980 to 18% in 2010. These market developments have given rise to a debate around a number of crucial issues related to the role of agricultural trade for global food security, for the environment or for poverty reduction in developing countries. This thesis uses an integrated framework to analyze a broad array of possible impacts related to transforming agricultural and rural markets in light of globalization, and in particular of increasing trade activity. Specifically, the following issues are approached: First, global food production will have to rise substantially by the year 2050 to meet effective demand of a nine billion people world population which poses major challenges to food production systems. Doing so without compromising environmental integrity in exporting regions is an even greater challenge. In this context, the thesis explores the effects of future global trade liberalization on food security indicators in different world regions and on a variety of environmental indicators at different scales in Latin America and the Caribbean, in due consideration of different future agricultural production practices. The International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT) –a global dynamic partial equilibrium model of the agricultural sector developed by the International Food Policy Research Institute (IFPRI)– is applied to run different future production scenarios, and agricultural trade regimes out to 2050. Model results are linked to biophysical models, used to assess changes in water footprints and water quality, as well as impacts on biodiversity and carbon stocks from land use change by 2050. Results indicate that further trade liberalization is crucial for improving food security globally, but that it would also lead to more environmental pressures in some regions across Latin America. Contrasting land expansion versus more intensified agriculture shows that productivity improvements are generally superior to agricultural land expansion, from an economic and environmental point of view. Most promising for achieving food security and environmental goals, in equal measure, is the sustainable intensification scenario. However, the analysis shows that there are trade-offs between environmental and food security goals for all agricultural development paths. Second, in light of the recent food price crisis of 2007/08, the thesis looks at the impacts of increasing agricultural market integration on food price transmission from global to domestic markets in six Latin American countries, namely Argentina, Brazil, Chile, Colombia, Mexico and Peru. To identify possible cointegrating relationships between the domestic food consumer price indices and world food price levels, subject to different degrees of agricultural market integration in the six Latin American countries, a single equation error correction model is used. Results suggest that global agricultural market integration has led to different levels of price path-through in the studied countries. Especially in the short-run, transmission rates depend on the degree of trade openness, while in the long-run transmission rates are high, but largely independent of the country-specific trade regime. Hence, under world price shocks more trade openness brings with it more price instability in the short-term and the resulting persistence in the long-term. However, these findings do not necessarily verify the usefulness of trade policies, often applied by governments to buffer such price shocks. First, because there is a considerable risk of price volatility due to domestic supply shocks if self-sufficiency is promoted. Second, protectionism bears the risk of excluding a country from participating in beneficial high-value agricultural supply chains, thereby hampering economic development. Nevertheless, to reduce households’ vulnerability to sudden and large increases of food prices, effective policies to buffer food price shocks should be put in place, but must be carefully planned with the required budget readily available. Third, globalization affects the structure of an economy and, by different means, the distribution of income in a country. Peru serves as an example to dive deeper into questions related to changes in the income distribution in rural areas. Peru, a country being increasingly integrated into global food markets, experienced large drops in extreme rural poverty, but persistently high rates of moderate rural poverty and rural income inequality between 2004 and 2012. The thesis aims at disentangling the driving forces behind these dynamics by using a microsimulation model based on rural household income generation models. Results provide evidence that the main force behind poverty reduction was overall economic growth of the economy due to generally favorable macroeconomic market conditions. These growth effects benefited almost all rural sectors, and led to declines in extreme rural poverty, especially among potato and maize farmers. In part, these farmers probably benefited from policy changes towards more open trade regimes and the resulting higher producer prices in times of elevated global food price levels. However, the results also suggest that entry barriers existed for the poorer part of the population to participate in well-paid wage-employment outside of agriculture or in high-value crop production. This could be explained by a lack of sufficient access to important rural assets. For example, poor people’s educational attainment was hardly better in 2012 than in 2004. Also land and labor endowments, especially of (poor) maize and potato growers, rather decreased than increased over time. This leads to the conclusion that there is still scope for policy action to facilitate access to these assets, which could contribute to the eradication of rural poverty. The thesis concludes that agricultural trade can be one important means to provide a growing and richer world population with sufficient amounts of calories. To avoid adverse environmental effects and negative impacts for poor food consumers and producers, the focus should lie on agricultural productivity improvements, considering environmental limits and be socially inclusive. In this sense, it will be crucial to further develop technological solutions that guarantee resource-sparing agricultural production practices, and to remove entry barriers for small poor farmers to export markets which might allow for technological spill-over effects from high-value global agricultural supply chains.

Definición e implantación de herramientas avanzadas 3D en el diseño integrado y eficiente de sistemas HVAC en buques, desde el proyecto conceptual hasta la producción

Uno de los aspectos más complicados del diseño de sistemas HVAC en buques es la correcta evaluación de las necesidades de aire fresco y el correcto dimensionado de los conductos que suministran dicho aire y evacuan el calor generado a bordo. Contrariamente a lo que sucede en los sistemas de tuberías, las características particulares del caudal de aire hacen que el dimensionado de los conductos sea muy sensible al trazado y geometría de los mismos, por lo que para obtener un buen diseño es necesaria una relación muy estrecha y una integración bidireccional entre los cálculos y el trazado de los propios conductos en el buque. Asumida la utilización de sistemas CAD/CAM para las tareas de diseño, históricamente, aquellos que permitían modelar conductos HVAC no incluían en su alcance de suministro los aspectos de cálculo, y como consecuencia de ello, el trazado de conductos se reducía a la inclusión en el modelo 3D de circuitos y sistemas previamente calculados y dimensionados, Así, servían únicamente para calcular interferencias con otros elementos del modelo 3D y para obtener posteriormente planos de fabricación y montaje. Esto, que por sí no es poco, dejaba el diseño de sistemas HVAC pendiente de una importante interacción manual y de habituales retrabajos, ya que cualquier modificación en el trazado de los conductos, consecuencia de otras necesidades del diseño, obligaba a los diseñadores a recalcular y redimensionar los conductos en un entorno diferente al del propio sistema CAD/CAM, y volver a realizar el modelado de los mismos, reduciendo significativamente las ventajas de la utilización de un modelo 3D. Partiendo de esta situación real, y con objeto de solucionar el problema que para el diseño y la propia producción del buque se creaba, se concibió una herramienta que permitiera la definición en el modelo 3D de diagramas de ventilación, el cálculo de pérdidas de presión, el dimensionado automático de los conductos, y que toda esta información pudiera estar disponible y reutilizarse en las etapas posteriores del diseño. Con ello, los diseñadores podrían realizar su trabajo en un entorno único, totalmente integrado con el resto de disciplinas. El objeto de esta Tesis Doctoral es analizar en detalle el problema y las ineficiencias actuales del diseño de HVAC, describir la innovadora herramienta concebida para paliar estas ineficiencias, detallando las bases sobre la que se construye, y destacar las ventajas que se obtienen de su uso. La herramienta en cuestión fue concebida como una funcionalidad adicional del sistema CAD/CAM naval FORAN, referente tecnológico en el mundo del diseño y la construcción navales, y como consecuencia de ellos se llevó a cabo el desarrollo correspondiente. En la actualidad, el sistema FORAN incluye en su alcance de suministro una primera versión de esta herramienta, cuya utilidad queda avalada por el uso que de la misma hacen astilleros y oficinas técnicas en todo el mundo. Esta Tesis Doctoral es eminentemente práctica. No es un estudio teórico de dudosa aplicación, sino que tiene por objeto aportar una solución eficiente a un problema real que muchos astilleros y oficinas técnicas, incluidas los más avanzados, padecen hoy en día. No tiene otra motivación que servir de ayuda para lograr diseñar y construir mejores barcos, en un plazo más corto, y a un coste menor. Nada más, pero nada menos. ABSTRACT One of the most complicated aspects of the design of HVAC systems in shipbuilding is the correct evaluation of the fresh air needs, the correct balancing of the ducts that supply this air and evacuate the existing heat on board. In opposition to piping systems, due to the particular characteristics of the air flow, the balancing of the ducts is very sensitive to the routing and the aspect of the ducts, so the correct design requires a close interconnectivity between calculations and routing. Already assumed the use of CAD/CAM systems for design tasks, historically, those CAD/CAM systems capable of modelling HVAC ducts did not cover calculation aspects, with the result that the routing of HVAC ducts was reduced solely to the input of previously balanced circuits into the 3D Product Model for the purpose of interference checking and generation of fabrication and assembly drawings. This situation, not negligible at all, put the design of HVAC ducts very dependent on manual operations and common rework task, as any modification in the routing of the HVAC ducts, derived from design needs, obliged engineers to re-balance the ducts and eventually to re-size them independently of the CAD-CAM environment, thus annulling the advantages of the 3D Product Model. With this situation in mind, and with the objective of filling the gap created in the design and construction of the ship, it was conceived a tool allowing the definition, within the 3D Product model, of HVAC diagrams, the calculation of pressure drops, the automatic dimensioning of ducts. With this, engineers could make the complete HVAC design in a single working environment, fully integrated with the rest of the disciplines. The present Ph. D. thesis analyses in deep the existing problem and the current lack of efficiency in HVAC design, describes the innovative tool conceived to minimize it, details the basis on which the tool is built, and highlights the advantages of its use. This tool was conceived as an additional functionality of the marine CAD/CAM system FORAN, a technological reference in the shipdesign and shipbuilding industry. As a consequence, it was developed, and nowadays FORAN System includes in its scope of supply a first version of the tool, with its usefulness endorsed by the fact that it is used by shipyards and shipdesign offices all over the world. This Ph. D. thesis is on top everything, of practical nature. It is not a theoretical study with doubtful application. On the contrary, its objective is to provide with an efficient solution for solving a real problem that many shipyards and shipdesign offices, including those more advanced, suffer nowadays. It has no other motivation that to help in the process of designing and building better and cheaper ships, within a shorter deliver time. Nothing more, but nothing less.

Efecto de la infección por virus persistentes y no persistentes sobre el comportamiento alimenticio, la preferencia, tasa de aterrizaje y asentamiento y la eficacia biológica de Aphis gossypii Glover

En el complejo de plagas que atacan a los principales cultivos hortícolas protegidos, destacan principalmente los Hemípteros, y dentro de estos los pulgones, dada su importancia como vectores de virus que provocan considerables daños y pérdidas económicas. Debido a que la dispersión de la mayoría de los virus de plantas puede ser eficaz con densidades bajas de vectores y su control es muy complicado al no existir métodos curativos para su control, es necesario generar nuevos conocimientos sobre las interacciones virus-vector con el fin de desarrollar nuevas y eficaces estrategias de control. Por ello, el objetivo general de esta Tesis ha sido conocer el efecto de la infección viral (directo-mediado por la presencia del virus en el vector- e indirecto-mediado por las alteraciones físico-químicas que se originan en la planta como consecuencia de la infección viral-) sobre el comportamiento y eficacia biológica del vector Aphis gossypii Glover y sus posibles repercusiones en la epidemiología de virosis de transmisión no persistente (Cucumber mosaic virus, CMV, Cucumovirus) y persistente (Cucurbit aphid-borne yellows virus, CABYV, Polerovirus). El primer objetivo de esta Tesis Doctoral, se centró en el estudio del efecto indirecto del virus de transmisión no persistente CMV sobre el comportamiento alimenticio y la preferencia del pulgón A. gossypii en el cultivo de pepino. Los ensayos de despegue y aterrizaje mostraron que los pulgones que fueron liberados en las plantas de pepino infectadas con CMV tuvieron una mayor propensión en migrar hacia las plantas no infectadas (60, 120 y 180 minutos después de la liberación) que aquellos que fueron sometidos al tratamiento contrario (planta no infectada hacia planta infectada con CMV). El estudio de preferencia y asentamiento mostró que el vector A. gossypii prefiere asentarse en plantas infectadas con CMV en una etapa temprana de evaluación (30 minutos después de la liberación). Sin embargo, este comportamiento se revirtió en una etapa posterior (4 y 48 horas después de la liberación), donde los pulgones se asentaron más en las plantas no infectadas. A través de la técnica de Gráficos de Penetración Eléctrica (EPG) se observó un efecto indirecto del virus CMV, revelado por un cambio brusco en el comportamiento de prueba del pulgón a lo largo del tiempo, cuando éstos fueron expuestos a las plantas infectadas con CMV. Los primeros 15 minutos de registro EPG mostraron que los pulgones hicieron un número mayor de punciones intracelulares (potencial drops - pds) y pruebas en las plantas infectadas con CMV que en las plantas no infectadas. Por otra parte, la duración de la primera prueba fue más corta y la duración total de las pds por insecto fue mucho más larga en las plantas infectadas con CMV. Se observaron diferencias significativas en el tiempo transcurrido desde el final de la última pd hasta el final de la prueba, siendo ese tiempo más corto para los pulgones que estaban alimentándose en plantas infectadas con CMV. En la segunda hora de registro los pulgones rechazaron las plantas infectadas con CMV como fuente de alimento, permaneciendo menos tiempo en las fases de prueba en floema (fase de salivación – E1 y fase de ingestión del floema – E2). El comportamiento alimenticio observado sobre las plantas infectadas con CMV favorece la adquisición y posterior transmisión de los virus de transmisión no persistente, los cuales son adquiridos e inoculados durante la realización de pruebas intracelulares en las primeras pruebas de corta duración. En el segundo objetivo de la Tesis se evaluó el efecto directo e indirecto del virus de transmisión persistente CABYV en el comportamiento alimenticio y preferencia del pulgón A. gossypii en cultivo de pepino, especie susceptible al virus, y algodón, especie inmune al virus. No se observó un efecto directo del virus relevante en el comportamiento alimenticio del vector, ya que los resultados obtenidos a nivel floemático en plantas de pepino no se observaron en plantas de algodón, inmune al virus CABYV. Esto sugiere que los resultados obtenidos en pepino, pueden deberse a un “posible efecto indirecto” originado por la infección de las plantas susceptibles al virus durante la realización del ensayo, lo que indirectamente puede modificar el comportamiento del pulgón durante la fase de evaluación. Sin embargo, el virus CABYV modificó indirectamente el comportamiento alimenticio de su vector a través de cambios en la planta infectada. Los pulgones tardaron menos tiempo en llegar al floema, realizaron un mayor número de pruebas floemáticas y permanecieron durante más tiempo en actividades floemáticas en plantas infectadas con CABYV. El comportamiento observado sobre las plantas infectadas con CABYV favorece la adquisición de virus persistentes, los cuales son adquiridos durante la alimentación sostenida en floema. El estudio de preferencia y asentamiento de A. gossypii mostró que los pulgones virulíferos prefieren asentarse en plantas no infectadas a corto y largo plazo de evaluación (2, 4 y 48 horas después de la liberación). Los ensayos de despegue y aterrizaje mostraron que los pulgones virulíferos que fueron liberados en las plantas de pepino infectadas con CABYV tuvieron una mayor propensión en migrar hacia las plantas no infectadas (3, 6, 24 y 48 horas después de la liberación) que aquellos que fueron sometidos al tratamiento contrario (planta no infectada hacia planta infectada con CABYV). Sin embargo, los pulgones no virulíferos no mostraron preferencia por plantas de pepino no infectadas o infectadas con CABYV en ninguno de los ensayos (preferencia o despegue) o periodos evaluados (corto y largo plazo). Los resultados indican que el virus CABYV es capaz de modificar indirectamente el comportamiento alimenticio de su vector a través de cambios en la planta infectada, favoreciendo su adquisición por su principal vector, A. gossypii. Una vez que los pulgones tienen capacidad de transmitir el virus (virulíferos) se produce un cambio en su comportamiento prefiriendo asentarse sobre plantas no infectadas optimizándose así la dispersión viral. El tercer objetivo de la Tesis, fue evaluar los efectos directos e indirectos del virus CABYV así como los efectos indirectos del virus CMV en la eficacia biológica del vector A. gossypii. Los resultados obtenidos en los ensayos realizados con el virus persistente CABYV indican que el virus parece no modificar directamente ni indirectamente la eficacia biológica del vector en plantas de pepino o algodón, no observándose diferencias estadísticas en ninguno de los parámetros poblacionales evaluados (tiempo de desarrollo, tasa intrínseca de crecimiento, tiempo generacional medio, tasa media de crecimiento relativo y ninfas totales). En cuanto a los ensayos realizados con el virus no persistente, CMV, los resultados muestran un efecto indirecto del virus sobre la biología del vector. Así resultó que tanto la tasa intrínseca de crecimiento natural (rm) como la tasa media de crecimiento relativo (RGR) fueron más altas para pulgones crecidos sobre plantas infectadas con CMV que sobre plantas no infectadas, favoreciendo la reproducción y crecimiento poblacional del vector sobre plantas infectadas con CMV. Los resultados obtenidos en la presente Tesis, ofrecen un ejemplo de como los virus de plantas pueden manipular directa e indirectamente a su vector, maximizando así su dispersión entre las plantas. Esos nuevos conocimientos generados tienen implicaciones importantes en la transmisión, dispersión y en la epidemiología de los virus y deben ser considerados para diseñar o ajustar los modelos de simulación existentes y patrones de dispersión que describen las epidemias de estos virus. ABSTRACT The main objective of this Thesis has been to understand the effect of the viral infection (direct-mediated by the presence of the virus in the vector and indirect mediated by the chemical and physical changes originated in the plant as a consequence of the viral infection) on the behaviour and biological efficacy of the vector Aphis gossypii Glover and its consequences in the epidemiology of two viral diseases, one with non-persistent transmission (Cucumber mosaic virus, CMV, Cucumovirus) and another with persistent transmission (Cucurbit aphid-borne yellows virus, CABYV, Polerovirus). The first objective of this Thesis was the study of the indirect effect of the nonpersistent virus CMV on the feeding behaviour and preference of the aphid A. gossypii in cucumber plants. The results of the alighting and settling behaviour studies showed that aphids exhibited no preference to migrate from CMV-infected to mock-inoculated plants at short time intervals (1, 10 and 30 min after release), but showed a clear shift in preference to migrate from CMV-infected to mock-inoculated plants 60 min after release. Our free-choice preference assays showed that A. gossypii alates preferred CMV-infected over mockinoculated plants at an early stage (30 min), but this behaviour was reverted at a later stage and aphids preferred to settle and reproduce on mock-inoculated plants. The electrical penetration graph (EPG) technique revealed a sharp change in aphid probing behaviour over time when exposed to CMV-infected plants. At the beginning (first 15 min) aphid vectors dramatically increased the number of short superficial probes and intracellular punctures when exposed to CMV-infected plants. At a later stage (second hour of recording) aphids diminished their feeding on CMV-infected plants as indicated by much less time spent in phloem salivation and ingestion (E1 and E2). This particular probing behaviour including an early increase in the number of short superficial probes and intracellular punctures followed by a phloem feeding deterrence is known to enhance the transmission efficiency of viruses transmitted in a NP manner. We conclude that CMV induces specific changes in a plant host that modify the alighting, settling and probing behaviour of its main vector A. gossypii, leading to optimum transmission and spread of the virus. The second objective of this work was to evaluate the effects that the persistently aphid transmitted Cucurbit aphid-borne yellows virus (CABYV) can induce directly and indirectly on the alighting, settling and probing behaviour activities of the cotton aphid A. gossypii. Only minor direct changes on aphid feeding behaviour was observed due to CABYV when viruliferous aphids fed on mock-inoculated plants. However, the feeding behaviour of non-viruliferous aphids was very different on CABYV-infected than on mockinoculated plants. Non-viruliferous aphids spent longer time feeding from the phloem when plants were infected by CABYV than on mock-inoculated plants, suggesting that CABYV indirectly manipulates aphid feeding behaviour through its shared host plant in order to favour viral acquisition. The vector alighting and settling preference was compared between nonviruliferous and viruliferous aphids. Viruliferous aphids showed a clear preference for mockinoculated over CABYV-infected plants at short and long time, while such behaviour was not observed for non-viruliferous aphids. Overall, our results indicate that CABYV induces changes in its host plant that modifies aphid feeding behaviour in a way that virus acquisition from infected plants is enhanced. Once the aphids become viruliferous they prefer to settle on healthy plants, leading to optimize the transmission and spread of the virus. The third objective was to evaluate the direct and indirect effects of CABYV and indirect effects of the CMV on the A. gossypii fitness. Obtained results for the persistent virus CABYV showed that the virus did not modify the vector fitness in cucumber or cotton plants. None of the evaluated variables was statistically significant (development time (d), intrinsic growth rate (rm), mean relative growth rate (RGR) and total number of nymphs). On the other hand, data obtained for the non-persistent virus (CMV) showed an indirect effect of the virus on the vector fitness. Thus, the rm and RGR were higher for aphids grown on CMV-infected plants compared to aphids grown on mock-inoculated plants. Overall, the obtained results are clear examples of how plant viruses could manipulate directly and indirectly vector behaviour to optimize its own dispersion. These results are important for a better understanding of transmission, dispersion and epidemiology of plant viruses transmitted by vectors. This information could be also considered to design or adjust simulation models and dispersion patterns that describe plant virus epidemics.

50 Years Ago We Marched: What began on the grounds of Lincoln University, ended on the steps of the Alabama State Capitol

LINCOLN UNIVERSITY - On March 25, 1965, a bus loaded with Lincoln University students and staff arrived in Montgomery, Ala. to join the Selma march for racial and voting equality. Although the Civil Rights Act of 1964 was in force, African-Americans continued to feel the effects of segregation. The 1960s was a decade of social unrest and change. In the Deep South, specifically Alabama, racial segregation was a cultural norm resistant to change. Governor George Wallace never concealed his personal viewpoints and political stance of the white majority, declaring “Segregation now, segregation tomorrow, segregation forever.” The march was aimed at obtaining African-Americans their constitutionally protected right to vote. However, Alabama’s deep-rooted culture of racial bias began to be challenged by a shift in American attitudes towards equality. Both black and whites wanted to end discrimination by using passive resistance, a movement utilized by Dr. Martin Luther King Jr. That passive resistance was often met with violence, sometimes at the hands of law enforcement and local citizens. The Selma to Montgomery march was a result of a protest for voting equality. The Student Nonviolent Coordinating Committee (SNCC) and the Southern Christian Leadership Counsel (SCLC) among other students marched along the streets to bring awareness to the voter registration campaign, which was organized to end discrimination in voting based on race. Violent acts of police officers and others were some of the everyday challenges protesters were facing. Forty-one participants from Lincoln University arrived in Montgomery to take part in the 1965 march for equality. Students from Lincoln University’s Journalism 383 class spent part of their 2015 spring semester researching the historical event. Here are their stories: Peter Kellogg “We’ve been watching the television, reading about it in the newspapers,” said Peter Kellogg during a February 2015 telephone interview. “Everyone knew the civil rights movement was going on, and it was important that we give him (Robert Newton) some assistance … and Newton said we needed to get involve and do something,” Kellogg, a lecturer in the 1960s at Lincoln University, discussed how the bus trip originated. “That’s why the bus happened,” Kellogg said. “Because of what he (Newton) did - that’s why Lincoln students went and participated.” “People were excited and the people along the sidewalk were supportive,” Kellogg said. However, the mood flipped from excited to scared and feeling intimidated. “It seems though every office building there was a guy in a blue uniform with binoculars standing in the crowd with troops and police. And if looks could kill me, we could have all been dead.” He says the hatred and intimidation was intense. Kellogg, being white, was an immediate target among many white people. He didn’t realize how dangerous the event in Alabama was until he and the others in the bus heard about the death of Viola Liuzzo. The married mother of five from Detroit was shot and killed by members of the Ku Klux Klan while shuttling activists to the Montgomery airport. “We found out about her death on the ride back,” Kellogg recalled. “Because it was a loss of life, and it shows the violence … we could have been exposed to that danger!” After returning to LU, Kellogg’s outlook on life took a dramatic turn. Kellogg noted King’s belief that a person should be willing to die for important causes. “The idea is that life is about something larger and more important than your own immediate gratification, and career success or personal achievements,” Kellogg said. “The civil rights movement … it made me, it made my life more significant because it was about something important.” The civil rights movement influenced Kellogg to change his career path and to become a black history lecturer. Until this day, he has no regrets and believes that his choices made him as a better individual. The bus ride to Alabama, he says, began with the actions of just one student. Robert Newton Robert Newton was the initiator, recruiter and leader of the Lincoln University movement to join Dr. Martin Luther King’s march in Selma. “In the 60s much of the civil rights activists came out of college,” said Newton during a recent phone interview. Many of the events that involved segregation compelled college students to fight for equality. “We had selected boycotts of merchants, when blacks were not allowed to try on clothes,” Newton said. “You could buy clothes at department stores, but no blacks could work at the department stores as sales people. If you bought clothes there you couldn’t try them on, you had to buy them first and take them home and try them on.” Newton said the students risked their lives to be a part of history and influence change. He not only recognized the historic event of his fellow Lincolnites, but also recognized other college students and historical black colleges and universities who played a vital role in history. “You had the S.N.C.C organization, in terms of voting rights and other things, including a lot of participation and working off the bureau,” Newton said. Other schools and places such as UNT, Greenville and Howard University and other historically black schools had groups that came out as leaders. Newton believes that much has changed from 50 years ago. “I think we’ve certainly come a long way from what I’ve seen from the standpoint of growing up outside of Birmingham, Alabama,” Newton said. He believes that college campuses today are more organized in their approach to social causes. “The campus appears to be some more integrated amongst students in terms of organizations and friendships.” Barbara Flint Dr. Barbara Flint grew up in the southern part of Arkansas and came to Lincoln University in 1961. She describes her experience at Lincoln as “being at Lincoln when the world was changing.“ She was an active member of Lincoln’s History Club, which focused on current events and issues and influenced her decision to join the Selma march. “The first idea was to raise some money and then we started talking about ‘why can’t we go?’ I very much wanted to be a living witness in history.” Reflecting on the march and journey to Montgomery, Flint describes it as being filled with tension. “We were very conscious of the fact that once we got on the road past Tennessee we didn’t know what was going to happen,” said Flint during a February 2015 phone interview. “Many of the students had not been beyond Missouri, so they didn’t have that sense of what happens in the South. Having lived there you knew the balance as well as what is likely to happen and what is not likely to happen. As my father use to say, ‘you have to know how to stay on that line of balance.’” Upon arriving in Alabama she remembers the feeling of excitement and relief from everyone on the bus. “We were tired and very happy to be there and we were trying to figure out where we were going to join and get into the march,” Flint said. “There were so many people coming in and then we were also trying to stay together; that was one of the things that really stuck out for me, not just for us but the people who were coming in. You didn’t want to lose sight of the people you came with.” Flint says she was keenly aware of her surroundings. For her, it was more than just marching forward. “I can still hear those helicopters now,” Flint recalled. “Every time the helicopters would come over the sound would make people jump and look up - I think that demonstrated the extent of the tenseness that was there at the time because the helicopters kept coming over every few minutes.” She said that the marchers sang “we are not afraid,” but that fear remained with every step. “Just having been there and being a witness and marching you realize that I’m one of those drops that’s going to make up this flood and with this flood things will move,” said Flint. As a student at Lincoln in 1965, Flint says the Selma experience undoubtedly changed her life. “You can’t expect to do exactly what you came to Lincoln to do,” Flint says. “That march - along with all the other marchers and the action that was taking place - directly changed the paths that I and many other people at Lincoln would take.” She says current students and new generations need to reflect on their personal role in society. “Decide what needs to be done and ask yourself ‘how can I best contribute to it?’” Flint said. She notes technology and social media can be used to reach audiences in ways unavailable to her generation in 1965. “So you don’t always have to wait for someone else to step out there and say ‘let’s march,’ you can express your vision and your views and you have the means to do so (so) others can follow you. Jaci Newsom Jaci Newsom came to Lincoln in 1965 from Atlanta. She came to Lincoln to major in sociology and being in Jefferson City was largely different from what she had grown up with. “To be able to come into a restaurant, sit down and be served a nice meal was eye-opening to me,” said Newsom during a recent interview. She eventually became accustomed to the relaxed attitude of Missouri and was shocked by the situation she encountered on an out-of-town trip. “I took a bus trip from Atlanta to Pensacola and I encountered the worse racism that I have ever seen. I was at bus stop, I went in to be served and they would not serve me. There was a policeman sitting there at the table and he told me that privately owned places could select not to serve you.” Newsom describes her experience of marching in Montgomery as being one with a purpose. “We felt as though we achieved something - we felt a sense of unity,” Newsom said. “We were very excited (because) we were going to hear from Martin Luther King. To actually be in the presence of him and the other civil rights workers there was just such enthusiasm and excitement yet there was also some apprehension of what we might encounter.” Many of the marchers showed their inspiration and determination while pressing forward towards the grounds of the Alabama Capitol building. Newsom recalled that the marchers were singing the lyrics “ain’t gonna let nobody turn me around” and “we shall overcome.” “ I started seeing people just like me,” Newsom said. “I don’t recall any of the scowling, the hitting, the things I would see on TV later. I just saw a sea of humanity marching towards the Capitol. I don’t remember what Martin Luther King said but it was always the same message: keep the faith; we’re going to get where we’re going and let us remember what our purpose is.” Newsom offers advice on what individuals can do to make their society a more productive and peaceful place. “We have come a long way and we have ways to change things that we did not have before,” Newsom said. “You need to work in positive ways to change.” Referencing the recent unrest in Ferguson, Mo., she believes that people become destructive as a way to show and vent anger. Her generation, she says, was raised to react in lawful ways – and believe in hope. “We have faith to do things in a way that was lawful and it makes me sad what people do when they feel without hope, and there is hope,” Newsom says. “Non-violence does work - we need to include everyone to make this world a better place.” Newsom graduated from Lincoln in 1969 and describes her experience at Lincoln as, “I grew up and did more growing at Lincoln than I think I did for the rest of my life.”

High phosphorylation efficiency and depression of uncoupled respiration in mitochondria under hypoxia

Mitochondria are confronted with low oxygen levels in the microenvironment within tissues; yet, isolated mitochondria are routinely studied under air-saturated conditions that are effectively hyperoxic, increase oxidative stress, and may impair mitochondrial function. Under hypoxia, on the other hand, respiration and ATP supply are restricted. Under these conditions of oxygen limitation, any compromise in the coupling of oxidative phosphorylation to oxygen consumption could accentuate ATP depletion, leading to metabolic failure. To address this issue, we have developed the approach of oxygen-injection microcalorimetry and ADP-injection respirometry for evaluating mitochondrial function at limiting oxygen supply. Whereas phosphorylation efficiency drops during ADP limitation at high oxygen levels, we show here that oxidative phosphorylation is more efficient at low oxygen than at air saturation, as indicated by higher ratios of ADP flux to total oxygen flux at identical submaximal rates of ATP synthesis. At low oxygen, the proton leak and uncoupled respiration are depressed, thus reducing maintenance energy expenditure. This indicates the importance of low intracellular oxygen levels in avoiding oxidative stress and protecting bioenergetic efficiency.

Comparing protein–ligand interactions in solution and single crystals by Raman spectroscopy

By using a Raman microscope, we show that it is possible to probe the conformational states in protein crystals and crystal fragments under growth conditions (in hanging drops). The flavin cofactor in the enzyme para-hydroxybenzoate hydroxylase can assume two conformations: buried in the protein matrix (“in”) or essentially solvent-exposed (“out”). By using Raman difference spectroscopy, we previously have identified characteristic flavin marker bands for the in and out conformers in the solution phase. Now we show that the flavin Raman bands can be used to probe these conformational states in crystals, permitting a comparison between solution and crystal environments. The in or out marker bands are similar for the respective conformers in the crystal and in solution; however, significant differences do exist, showing that the environments for the flavin's isoalloxazine ring are not identical in the two phases. Moreover, the Raman-band widths of the flavin modes are narrower for both in and out conformers in the crystals, indicating that the flavin exists in a more limited range of closely related conformational states in the crystal than in solution. In general, the ability to compare detailed Raman data for complexes in crystals and solution provides a means of bridging crystallographic and solution studies.

Microfabricated structures for integrated DNA analysis.

Photolithographic micromachining of silicon is a candidate technology for the construction of high-throughput DNA analysis devices. However, the development of complex silicon microfabricated systems has been hindered in part by the lack of a simple, versatile pumping method for integrating individual components. Here we describe a surface-tension-based pump able to move discrete nanoliter drops through enclosed channels using only local heating. This thermocapillary pump can accurately mix, measure, and divide drops by simple electronic control. In addition, we have constructed thermal-cycling chambers, gel electrophoresis channels, and radiolabeled DNA detectors that are compatible with the fabrication of thermocapillary pump channels. Since all of the components are made by conventional photolithographic techniques, they can be assembled into more complex integrated systems. The combination of pump and components into self-contained miniaturized devices may provide significant improvements in DNA analysis speed, portability, and cost. The potential of microfabricated systems lies in the low unit cost of silicon-based construction and in the efficient sample handling afforded by component integration.