Nopeat ydinreaktorit

Nopeat ydinreaktorit ovat toiminnaltaan polttoainetehokkaampia kuin nykyään laajalti käytössä olevat termiset reaktorit. Tehokkuus perustuu siihen, että nopeassa reaktorissa ei tapahdu neutronien hidastumista, jolloin ne pystyvät esimerkiksi muuntamaan luonnonuraania ja muita fertiilejä aineita fissiileiksi aineiksi. Koska reaktorissa ei saa olla hidastinta, nopea reaktori ei voi käyttää jäähdytteenään vettä, vaan on käytettävä jotain raskaampia ytimiä sisältävää jäähdytettä, kuten natriumia. Natriumin käyttö tuo mukanaan tiettyjä ongelmia, sillä se on erittäin reaktioherkkä ilman ja veden kanssa. Nopeita reaktoreita on tosin käytetty ja tutkittu jo yli 50 vuotta, ja käyttökokemusten perusteella on löydetty toimivia ratkaisuja natriumin ongelmiin. Nopean reaktorin tehokas käyttö vaatii suljetun polttoainekierron, jossa käytetystä polttoaineesta voidaan valmistaa uutta polttoainetta joko nopealle tai termiselle reaktorille. Suljetun polttoainekierron infrastruktuuri on tosin hyvin kallista, joten sen käyttöönotto on kannattavaa lähinnä infrastruktuurin jo omaavissa maissa, kuten esimerkiksi Venäjällä. Nopeaa ja kevytvesireaktoria vertaillessa tulee esille tiettyjä yhtäläisyyksiä, erityisesti säteilyturvallisuuteen ja ydinturvallisuuteen liittyvissä asioissa. Suurimmat eroavaisuudet reaktorityyppien välillä nähdään polttoainetaloudessa ja jätehuollossa.

Lumen varastointi ja hyödyntäminen tilojen jäähdytykseen, Case: Kone Oyj

Tämän diplomityön tarkoituksena on selvittää mahdollisuutta hyödyntää lunta tilojen jäähdytykseen Koneen Hyvinkään tehdasalueella. Työssä kerrotaan myös yleisesti eri jäähdytysmuodoista ja tuotantotavoista. Eri kirjallisuuslähteiden pohjalta tutkittiin erilaisia lumijäähdytysjärjestelmiä, joiden energiataseiden pohjalta tehtiin sopiva malli kohdealueelle. Mallin avulla selvitettiin lumesta hyödynnettävä jäähdytysenergian määrä. Esitetylle varastolle hahmoteltiin investointi- ja käyttökustannukset kirjallisuuslähteiden ja asiantuntijoiden avulla. Kustannuksien ja jäähdytysenergiamäärien avulla laskettiin lumijäähdytyksen tuotantokustannukset, joita verrattiin perinteiseen kompressorijäähdyttimeen. Lopuksi pohdittiin vielä takaisinmaksuaikoja lumivaraston liittyessä nykyisiin jäähdytysjärjestelmiin ja kokonaan uuteen jäähdytysverkostoon. Tuloksien mukaan lumijäähdytys ei ole taloudellisesti kannattavaa Koneen Hyvinkään tehdasalueella. Ongelmaksi muodostui investointikustannusten suuruus verrattuna saatuihin säästöihin. Ympäristöllisesti ja yrityksellisesti hanketta voidaan pitää kannattavana. Lumijäähdytyksestä voidaan saada kannattavampi suuremmilla lumimäärillä, mikä vaatisi myös suuremmat jäähdytysenergiankulutukset kuin Koneella on. Myös hyödyntämällä luonnon omia rakenteita voidaan parantaa kannattavuutta.

Kaksifaasijäähdytysjärjestelmään liittyvien pumppujen vertailu ja kehittäminen sarjatuotannon tarpeisiin

Tehoelektroniikalta vaaditaan nykyään parempaa suorituskykyä entistä pienemmässä tilassa. Tämä luo haasteen riittävälle jäähdytykselle. Eräs ratkaisu on käyttää kaksifaasijäähdytystä, jolla aikaansaadaan tehokas lämmönsiirto komponenttien pinnalta. Lämmönsiirtonesteinä voidaan käyttää kylmäaineita tai muita alhaisessa lämpötilassa kiehuvia nesteitä. Tällaisille nesteille on tyypillistä alhainen höyrynpaine sekä matala viskositeetti. Nämä ominaisuudet tuovat haasteita nesteen pumppaukseen. Tässä työssä tarkastellaan R-134A:ta sekä Novec 7000:ta, perehdytään niiden fysikaalisiin ominaisuuksiin sekä materiaaliyhteensopivuuksiin ja näiden tietojen pohjalta etsitään sopivaa pumpputyyppiä kaksifaasijäähdytysjärjestelmään. Tehoelektroniikan jäähdytysjärjestelmän pumpun on oltava edullinen muuhun järjestelmään nähden. Tyypillinen kiertopumppu nestejäähdytysjärjestelmässä on pieni keskipakopumppu. Alhaisen kiehumispisteen vuoksi kavitointiriski kasvaa ja tämä voi vahingoittaa pumppua. Myös matala viskositeetti tuo haasteita vuotoherkkyyden kasvamisen myötä, joten mekaanisilla aksiaalitiivisteillä varustetut pumput eivät ole pitkäikäisiä. Kylmäainejärjestelmiin tarkoitetut pumput ovat arvokkaita, eikä näin ollen sovellu edullisiin jäähdytysjärjestelmiin. Tässä työssä käydään läpi erilaisia pumpputyyppejä, jotka voisivat soveltua pitkäikäiseen pumppaukseen ilman huoltotöitä. Näiden tietojen perusteella kehitetään edullista ja pitkäikäistä pumppua pieniin kaksifaasijäähdytysjärjestelmiin nesteiden fysikaaliset ominaisuudet huomioon ottaen. Kehitetyn pumpun ominaisuuksia ja kustannuksia vertaillaan kaupallisiin ratkaisuihin ottaen huomioon sarjavalmistus. Itse valmistettuna pienelle sisäryntöiselle hammaspyöräpumpulle jää hintaa alle kymmenesosa markkinoilta löytyviin kylmäaineille soveltuviin pumppuun.

Influence of Pulsed-Electric Field Irradiation in Crystallization

The growing pharmaceutical interest, among others, in the polymorphic composition of the emerging solid end-products from production processes has been traced to the need for attainment of high product purity. This is more so as the presence of different polymorphs may constitute physical impurity of the product. Hence, the need for optimization of the yield of desired product component(s) through controlled crystallization kinetics for instance. This study was carried out to investigate the impact of pulsed electric field (PEF) irradiation on the crystal morphology of glycine obtained by cooling crystallization (without seeding) from commercial glycine sample in distilled deionized water solution. In doing so, three different pulse frequencies (294, 950 and 145 Hz) and a case without PEF were studied at three cooling rates (5, 10 and 20 ºC/h). The crystal products obtained were analyzed for polymorphic composition by powder x-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy while the particles characterization was done on Morphologi G3. The results obtained from this study showed that pulsed electric field irradiation had significant impact on metastability of the aqueous solution as well as on the polymorphic composition of the end product. With increasing PEF frequency applied, nucleation started earlier and the γ-glycine polymorph content of the product crystals increased. These were found to have been aided by cooling rate, as the most significant effect was observed at 5 ºC/h. It was also discovered that PEF application had no measurable impact on the pH of the aqueous solution as well as the size distribution of the particles. Cooling on the contrary was believed to be responsible for the broadening of the particle size distribution with a downward shift of the lower limit of the raw material from about 100 μm to between 10 and 50 μm.

Lightweight, liquid-cooled, direct-drive generator for highpower wind turbines: motivation, concept, and performance

Thesis: A liquid-cooled, direct-drive, permanent-magnet, synchronous generator with helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit offers an excellent combination of attributes to reliably provide economic wind power for the coming generation of wind turbines with power ratings between 5 and 20MW. A generator based on the liquid-cooled architecture proposed here will be reliable and cost effective. Its smaller size and mass will reduce build, transport, and installation costs. Summary: Converting wind energy into electricity and transmitting it to an electrical power grid to supply consumers is a relatively new and rapidly developing method of electricity generation. In the most recent decade, the increase in wind energy’s share of overall energy production has been remarkable. Thousands of land-based and offshore wind turbines have been commissioned around the globe, and thousands more are being planned. The technologies have evolved rapidly and are continuing to evolve, and wind turbine sizes and power ratings are continually increasing. Many of the newer wind turbine designs feature drivetrains based on Direct-Drive, Permanent-Magnet, Synchronous Generators (DD-PMSGs). Being low-speed high-torque machines, the diameters of air-cooled DD-PMSGs become very large to generate higher levels of power. The largest direct-drive wind turbine generator in operation today, rated just below 8MW, is 12m in diameter and approximately 220 tonne. To generate higher powers, traditional DD-PMSGs would need to become extraordinarily large. A 15MW air-cooled direct-drive generator would be of colossal size and tremendous mass and no longer economically viable. One alternative to increasing diameter is instead to increase torque density. In a permanent magnet machine, this is best done by increasing the linear current density of the stator windings. However, greater linear current density results in more Joule heating, and the additional heat cannot be removed practically using a traditional air-cooling approach. Direct liquid cooling is more effective, and when applied directly to the stator windings, higher linear current densities can be sustained leading to substantial increases in torque density. The higher torque density, in turn, makes possible significant reductions in DD-PMSG size. Over the past five years, a multidisciplinary team of researchers has applied a holistic approach to explore the application of liquid cooling to permanent-magnet wind turbine generator design. The approach has considered wind energy markets and the economics of wind power, system reliability, electromagnetic behaviors and design, thermal design and performance, mechanical architecture and behaviors, and the performance modeling of installed wind turbines. This dissertation is based on seven publications that chronicle the work. The primary outcomes are the proposal of a novel generator architecture, a multidisciplinary set of analyses to predict the behaviors, and experimentation to demonstrate some of the key principles and validate the analyses. The proposed generator concept is a direct-drive, surface-magnet, synchronous generator with fractional-slot, duplex-helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit to accommodate liquid coolant flow. The novel liquid-cooling architecture is referred to as LC DD-PMSG. The first of the seven publications summarized in this dissertation discusses the technological and economic benefits and limitations of DD-PMSGs as applied to wind energy. The second publication addresses the long-term reliability of the proposed LC DD-PMSG design. Publication 3 examines the machine’s electromagnetic design, and Publication 4 introduces an optimization tool developed to quickly define basic machine parameters. The static and harmonic behaviors of the stator and rotor wheel structures are the subject of Publication 5. And finally, Publications 6 and 7 examine steady-state and transient thermal behaviors. There have been a number of ancillary concrete outcomes associated with the work including the following. X Intellectual Property (IP) for direct liquid cooling of stator windings via an embedded coaxial coolant conduit, IP for a lightweight wheel structure for lowspeed, high-torque electrical machinery, and IP for numerous other details of the LC DD-PMSG design X Analytical demonstrations of the equivalent reliability of the LC DD-PMSG; validated electromagnetic, thermal, structural, and dynamic prediction models; and an analytical demonstration of the superior partial load efficiency and annual energy output of an LC DD-PMSG design X A set of LC DD-PMSG design guidelines and an analytical tool to establish optimal geometries quickly and early on X Proposed 8 MW LC DD-PMSG concepts for both inner and outer rotor configurations Furthermore, three technologies introduced could be relevant across a broader spectrum of applications. 1) The cost optimization methodology developed as part of this work could be further improved to produce a simple tool to establish base geometries for various electromagnetic machine types. 2) The layered sheet-steel element construction technology used for the LC DD-PMSG stator and rotor wheel structures has potential for a wide range of applications. And finally, 3) the direct liquid-cooling technology could be beneficial in higher speed electromotive applications such as vehicular electric drives.

Attraction to amino acids by Lymnaea acuminata, the snail host of Fasciola species

Adult Lymnaea acuminata (average length 20-22 mm) were collected locally from lakes and low-lying submerged fields from Gorakhpur. The chemoattraction studies were made in round glass aquaria measuring 30 cm in diameter and filled to a depth of 10 mm with 500 ml dechlorinated tap water. Each aquarium was divided into four concentric zones. At the starting time of the assay 10 snails were placed on the circumference of outermost zone 0. Snail attractant pellets (SAP) were added simultaneously in the center of central zone 3. SAP of different amino acids were prepared at concentrations of 10, 20, 50, 80 and 100 mM/2% agar solution and, subsequently, spread to a uniform thickness of 5 mm. After cooling, SAP were cut in small pieces of 5 mm in diameter. Lymnaea acuminata's attraction to amino acids was studied using different amino acid concentrations in SAP. Pellets containing amino acids with non-polar R groups (proline and tryptophan), a charged polar group (arginine) and uncharged polar R groups (serine, citrulline and asparagine) were tested. The snails were more attracted to the uncharged polar R group amino acid serine than to other groups of amino acids. The preferred amino acid concentration was 80 mM. The attraction of snails to different amino acids was concentration dependent. Snails could discriminate amongst the different amino acids at > or = 50 mM.

An improved HPLC method for the quantitation of 6-mercaptopurine and its metabolites in red blood cells

A procedure is described for the rapid determination of the intra-erythrocyte concentration of 6-mercaptopurine (6-MP) and its metabolites, 6-thioguanine nucleotides (6-TGN) and 6-methylmercaptopurine (6-MMP). Erythrocytes (8 x 10(8) cells) in 350 µl Hanks solution containing 7.5 mg dithiothreitol were treated with 50 µl 70% perchloric acid. The precipitate was removed by centrifugation (13,000 g) and the supernatant hydrolyzed at 100°C for 45 min. After cooling, 100 µl was analyzed directly by HPLC using a Radialpack Resolve C18 column eluted with methanol-water (7.5:92.5, v/v) containing 100 mM triethylamine. 6-TG, 6-MP and the hydrolysis product of 6-MMP, 4-amino-5-(methylthio)carbonyl imidazole, were monitored at 342, 322 and 303 nm using a Shimadzu SPD-M10A diode array UV detector. The analytes eluted at 5.3, 6.0 and 10.2 min, respectively. The calibration curves were linear (r² > 0.998), and the analytical recoveries were 73.2% for 6-TG, 119.1% for 6-MP and 97.4% for 6-MMP. The intra- and inter-assay variations were highest for 6-MP (9.6 and 14.3%, respectively). The lowest detectable concentrations were 3, 3 and 25 pmol/8 x 10(8) erythrocytes for 6-TG, 6-MP and 6-MMP, respectively. The quantification limits (coefficients of variation <15%) were 8, 10 and 70 pmol/8 x 10(8) erythrocytes for 6-TG, 6-MP and 6-MMP, respectively. The method was applied to the analysis of 183 samples from 36 children under chemotherapy for acute lymphoblastic leukemia. The concentrations of the metabolites in the red cells of the patients ranged from 0 to 1934 pmol/8 x 10(8) erythrocytes for 6-TGN, and from 0 to 105.8 and 0 to 45.9 nmol/8 x 10(8) erythrocytes for 6-MP and 6-MMP, respectively. The procedure gave results that were in agreement with those obtained with other methods designed to detect cases of non-compliance with treatment, including patient interviews and medical evaluation, among others, demonstrating its applicability to monitoring the treatment of leukemic children.

Kylmälaitekoneikon runkorakenteen kehittäminen

Kylmälaitekoneikot ovat kylmäkomponentteja sisältäviä rakenteita, joiden avulla toteutetaan suurten tilojen, kuten elintarvikemyymälöiden sisäilman jäähdytys. Lisäksi koneikkojen avulla jäähdytetään matalampiin lämpötiloihin pienempiä kylmähuoneita. Osa koneikoista ottaa talteen kylmäprosessissa syntyvän lämmön, jota hyödynnetään tilojen lämmityksessä. Tämän diplomityön tavoitteena oli suunnitella ja mitoittaa kahdeksalle eri kylmälaitekoneikolle entistä kustannustehokkaammat runkorakenteet, jotka ovat niin kestäviä, että koneikkoja on mahdollista pinota tilan säästämiseksi kolme päällekkäin. Lisäksi runkorakenteilta vaadittiin helppoa kuljetettavuutta, hyviä kiinnitysominaisuuksia ja korroosionkestävyyttä. Aluksi työssä selvitettiin runkorakenteisiin kohdistuvat vaatimukset, jonka jälkeen materiaalin valinta tehtiin materiaaliin kohdistuvien vaatimusten perusteella. Rakenteiden palkit mitoitettiin tarvittavan taivutusvastuksen ja kiepahduksen mukaan. Pilarit puolestaan mitoitettiin nurjahduksen ja kaksiaksiaalisen taivutustilan perusteella. Tämän jälkeen mitoitettiin eri sauvojen väliset hitsi- ja ruuviliitokset siten, että rakenne hajoaa ylikuormitustilanteessa mahdollisimman turvallisesti. Työssä tehdyt laskelmat varmennettiin elementtimenetelmän avulla ja lopullisille rakenteille tehtiin elementtimenetelmällä vielä ominaistaajuusanalyysejä. Lopuksi työssä suunniteltiin runkorakenteille sopiva korroosionsuojaus.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Intensification of Operation of Inclined Plate Settler at Fertilizer Plant

Fertilizer plant’s process waters contain high concentrations of nitrogen compounds, such as ammonium and nitrate. Phosphorus and fluorine, which originate from phosphoric acid and rock phosphate (apatite) used in fertilizer production, are also present. Phosphorus and nitrogen are the primary nutrients causing eutrophication of surface waters. At fertilizer plant process waters are held in closed internal circulation. In a scrubber system process waters are used for washing exhaust gases from fertilizer reactors and dry gases from granulation drums as well as for cooling down the fertilizer slurry in neutralization reactor. Solids in process waters are separated in an inclined plate settler by gravitational sedimentation. However, the operation of inclined plate settler has been inadequate. The aim of this thesis was to intensify the operation of inclined plate settler and thus the solids separation e.g. through coagulation and/or flocculation process. Chemical precipitation was studied to reduce the amount of dissolved species in process waters. Specific interest was in precipitation of nitrogen, phosphorus, and fluorine containing specimens. Amounts of phosphorus and fluorine were reduced significantly by chemical precipitation. When compared to earlier studies, annual chemical costs were almost eight times lower. Instead, nitrogen compounds are readily dissolved in water, thus being difficult to remove by precipitation. Possible alternative techniques for nitrogen removal are adsorption, ion exchange, and reverse osmosis. Settling velocities of pH adjusted and flocculated process waters were sufficient for the operation of inclined plate settler. Design principles of inclined plate settler are also presented. In continuation studies, flow conditions in inclined plate settler should be modelled with computational fluid dynamics and suitability of adsorbents, ion exchange resins, and membranes should be studied in laboratory scale tests.

Optimization of a dynamic district heating power plant

The purpose of this Thesis is to find the most optimal heat recovery solution for Wärtsilä’s dynamic district heating power plant considering Germany energy markets as in Germany government pays subsidies for CHP plants in order to increase its share of domestic power production to 25 % by 2020. Different heat recovery connections have been simulated dozens to be able to determine the most efficient heat recovery connections. The purpose is also to study feasibility of different heat recovery connections in the dynamic district heating power plant in the Germany markets thus taking into consideration the day ahead electricity prices, district heating network temperatures and CHP subsidies accordingly. The auxiliary cooling, dynamical operation and cost efficiency of the power plant is also investigated.

Computational studies of deformation in stainless steel rings due to torch heating

A support ring of AISI 304L stainless steel that holds vertical, parallel wires arranged in a circle forming a cylinder is studied. The wires are attached to the ring with heat-induced shrinkage. When the ring is heated with a torch the heat affected zone tries to expand while the adjacent cool structure obstructs the expansion causing upsetting. During cooling, the ring shrinks smaller than its original size clamping the wires. The most important requirement for the ring is that it should be as round as possible and the deformations should occur as overall shrinkage in the ring diameter. A three-dimensional nonlinear transient sequential thermo-structural Abaqus model is used together with a Fortran code that enters the heat flux to each affected element. The local and overall deformations in one ring inflicted by the heating are studied with a small amount of inspection on residual stresses. A variety of different cases are chosen to be studied with the model constructed to provide directional knowledge; torch flux with the means of speed, location of the wires, heating location and structural factors. The decrease of heating speed increases heat flux that rises the temperature increasing shrinkage. In a single progressive heating uneven distribution of shrinkage appears to the start/end region that can be partially fixed with using speeded heating’s to strengthen the heating of that region. Location of the wires affect greatly to the caused shrinkage unlike heating location. The ring structure affects also greatly to the shrinkage; smaller diameter, bigger ring height, thinner thickness and greater number of wires increase shrinkage.

Palmupohjaisten raaka-aineiden soveltuvuus lämpökynttilämateriaaliksi

Työssä tutkittiin palmupohjaisten raaka-aineiden soveltuvuutta lämpökynttilän valmistukseen steariinin ja parafiinin kanssa. Palmupohjaiset raaka-aineet ovat halvempia kuin steariini ja parafiini, joten raaka-aineen korvaaminen palmupohjaisilla raaka-aineilla voisi tuoda säästöä kynttilänvalmistajalle. Lisäksi niillä voidaan vaikuttaa lämpökynttilän ominaisuuksiin. Teoriaosassa käsiteltiin lämpökynttilän raaka-aineista steariini, parafiini ja palmusteariini. Osassa selitettiin RAL-laatustandardin Quality Mark Candles vaatimukset lämpökynttilälle sekä valuastialle ja keskusteltiin valulämpötilan, jäähdytyksen, viskositeetin ja haaroittuneiden yhdisteiden lukumäärän vaikutuksesta lämpökynttilän koostumukseen. Kokeellisessa osassa valmistettiin lämpökynttilöitä steariinin ja palmupohjaisten raaka-aineiden seoksista palmuraaka-aineiden määrillä 10, 20 ja 30 m- %:a. Parafiinin ja palmusteariinin sekä palmun mid-fraktion seokset valmistettiin palmuraaka-aineiden osuuksilla 10, 20, 40 ja 50 m- %:a ja myös palmusteariinin soft-fraktiolla kokeiltiin seosta 50 m- %:lla. Steariinin ja palmupohjaisten raaka-aineiden seokset eivät toimineet ainakaan käytetyillä sydänlangoilla. Liekinkorkeudet olivat alhaisia eivätkä visuaaliset vaatimukset täyttyneet. Parafiinin ja palmupohjaisten raaka-aineiden seoksista valmistetut kynttilät paloivat ideaalisesti palmuraaka-aineiden osuuksilla 35 – 50 m- %:a. Tulosten perusteella fraktion valinnalla ei näyttänyt olevan merkitystä, mutta palmusteariini on ominaisuuksiensa puolesta kynttilänvalmistukseen soveltuvin. Liekinkorkeus ja palovuo laskivat lineaarisesti palmuraaka-aineen osuuden kasvaessa parafiinikynttilässä.

Hypertension is associated with greater heat exchange during exercise recovery in a hot environment

Individuals with systemic arterial hypertension have a higher risk of heat-related complications. Thus, the aim of this study was to examine the thermoregulatory responses of hypertensive subjects during recovery from moderate-intensity exercise performed in the heat. A total of eight essential hypertensive (H) and eight normotensive (N) male subjects (age=46.5±1.3 and 45.6±1.4 years, body mass index=25.8±0.8 and 25.6±0.6 kg/m2, mean arterial pressure=98.0±2.8 and 86.0±2.3 mmHg, respectively) rested for 30 min, performed 1 h of treadmill exercise at 50% of maximal oxygen consumption, and rested for 1 h after exercise in an environmental chamber at 38°C and 60% relative humidity. Skin and core temperatures were measured to calculate heat exchange parameters. Mean arterial pressure was higher in the hypertensive than in the normotensive subjects throughout the experiment (P<0.05, unpaired t-test). The hypertensive subjects stored less heat (H=-24.23±3.99 W·m−2vs N=-13.63±2.24 W·m−2, P=0.03, unpaired t-test), experienced greater variations in body temperature (H=-0.62±0.05°C vsN=-0.35±0.12°C, P=0.03, unpaired t-test), and had more evaporated sweat (H=-106.1±4.59 W·m−2vs N=-91.15±3.24 W·m−2, P=0.01, unpaired t-test) than the normotensive subjects during the period of recovery from exercise. In conclusion, essential hypertensive subjects showed greater sweat evaporation and increased heat dissipation and body cooling relative to normotensive subjects during recovery from moderate-intensity exercise performed in hot conditions.

Effect of heat input on the mechanical properties of welded joints in high strength steels

Experiments were carried out to determine the properties of the welded joints in 8mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm21 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.