Conventional in vivo irradiation procedures are insufficient to accurately determine tumor responses to non-uniform radiation fields

Purpose: To determine differences in overall tumor responses measured by volumetric assessment and bioluminescence imaging (BLI) following exposure to uniform and non-uniform radiation fields in an ectopic prostate tumor model.

Materials and methods: Bioluminescent human prostate tumor xenografts were established by subcutaneous implantation into male mice. Tumors were irradiated with uniform or non-uniform field configurations using conventional in vivo irradiation procedures performed using a 225 kVp generator with custom lead shielding. Tumor responses were measured using Vernier calipers and by BLI using an in vivo imaging system. Survival was defined as the time to quadroupling of pre-treatment tumor volume. 

Results: The correlation between BLI and tumor volume measurements was found to be different for un-irradiated (R = 0.61), uniformly irradiated (R = 0.34) and partially irradiated (R = 0.30) tumors. Uniformly irradiated tumors resulted in an average tumor growth delay of 60 days with median survival of 75 days, compared to partially irradiated tumors which showed an average growth delay of 24 days and median survival of 38 days. 

Conclusions: Correlation between BLI and tumor volume measurements is lower for partially irradiated tumors than those exposed to uniform dose distributions. The response of partially irradiated tumors suggests non-uniformity in response beyond physical dose distribution within the target volume. Dosimetric uncertainty associated with conventional in vivo irradiation procedures prohibits their ability to accurately determine tumor response to non-uniform radiation fields and stresses the need for image guided small animal radiation research platforms.

Small Signal Stability Performance of Power System during High Penetration of Wind Generation

The small signal stability of interconnected power systems is one of the important aspects that need to be investigated since the oscillations caused by this kind of instability have caused many incidents. With the increasing penetration of wind power in the power system, particularly doubly fed induction generator (DFIG), the impact on the power system small signal stability performance should be fully investigated. Because the DFIG wind turbine integration is through a fast action converter and associated control, it does not inherently participate in the electromechanical small signal oscillation. However, it influences the small signal stability by impacting active power flow paths in the network and replacing synchronous generators that have power system stabilizer (PSS). In this paper, the IEEE 39 bus test system has been used in the analysis. Furthermore, four study cases and several operation scenarios have been conducted and analysed. The selective eigenvalue Arnoldi/lanczos's method is used to obtain the system eigenvalue in the range of frequency from 0.2 Hz to 2 Hz which is related to electromechanical oscillations. Results show that the integration of DFIG wind turbines in a system during several study cases and operation scenarios give different influence on small signal stability performance.

DFIG Machine Design for Maximizing Power Output Based on Surrogate Optimization Algorithm

This paper presents a surrogate-model based optimization of a doubly-fed induction generator (DFIG) machine winding design for maximizing power yield. Based on site-specific wind profile data and the machine’s previous operational performance, the DFIG’s stator and rotor windings are optimized to match the maximum efficiency with operating conditions for rewinding purposes. The particle swarm optimization (PSO)-based surrogate optimization techniques are used in conjunction with the finite element method (FEM) to optimize the machine design utilizing the limited available information for the site-specific wind profile and generator operating conditions. A response surface method in the surrogate model is developed to formulate the design objectives and constraints. Besides, the machine tests and efficiency calculations follow IEEE standard 112-B. Numerical and experimental results validate the effectiveness of the proposed technologies.

New SR drive with integrated charging capacity for plug-in hybrid electric vehicles (PHEVs)

Plug-in hybrid electric vehicles (PHEVs) provide much promise in reducing greenhouse gas emissions and, thus, are a focal point of research and development. Existing on-board charging capacity is effective but requires the use of several power conversion devices and power converters, which reduce reliability and cost efficiency. This paper presents a novel three-phase switched reluctance (SR) motor drive with integrated charging functions (including internal combustion engine and grid charging). The electrical energy flow within the drivetrain is controlled by a power electronic converter with less power switching devices and magnetic devices. It allows the desired energy conversion between the engine generator, the battery, and the SR motor under different operation modes. Battery-charging techniques are developed to operate under both motor-driving mode and standstill-charging mode. During the magnetization mode, the machine's phase windings are energized by the dc-link voltage. The power converter and the machine phase windings are controlled with a three-phase relay to enable the use of the ac-dc rectifier. The power converter can work as a buck-boost-type or a buck-type dc-dc converter for charging the battery. Simulation results in MATLAB/Simulink and experiments on a 3-kW SR motor validate the effectiveness of the proposed technologies, which may have significant economic implications and improve the PHEVs' market acceptance

Building pH Sensors into Paper-based Small-molecular Logic Sys-tems for Very Simple Detection of Edges of Objects

Genetically-engineered bacteria and reactive DNA networks detect edges of objects, as done in our retinas and as also found within computer vision. We now demonstrate that simple molecular logic systems (a combination of a pH sensor, a photo acid generator and a pH buffer spread on paper) without any organization can achieve this relatively complex computational goal with good-fidelity. This causes a jump in the complexity achievable by molecular logic-based computation and extends its applicability. The molecular species involved in light dose-driven 'off-on-off' fluorescence is diverted in the ‘on’ state by proton diffusion from irradiated to unirradiated regions where it escapes a strong quencher, thus visualizing the edge of a mask.

Validation of non‑stationary precipitation series for site‑specific impact assessment: comparison of two statistical downscaling techniques

Statistical downscaling (SD) methods have become a popular, low-cost and accessible means of bridging the gap between the coarse spatial resolution at which climate models output climate scenarios and the finer spatial scale at which impact modellers require these scenarios, with various different SD techniques used for a wide range of applications across the world. This paper compares the Generator for Point Climate Change (GPCC) model and the Statistical DownScaling Model (SDSM)—two contrasting SD methods—in terms of their ability to generate precipitation series under non-stationary conditions across ten contrasting global climates. The mean, maximum and a selection of distribution statistics as well as the cumulative frequencies of dry and wet spells for four different temporal resolutions were compared between the models and the observed series for a validation period. Results indicate that both methods can generate daily precipitation series that generally closely mirror observed series for a wide range of non-stationary climates. However, GPCC tends to overestimate higher precipitation amounts, whilst SDSM tends to underestimate these. This infers that GPCC is more likely to overestimate the effects of precipitation on a given impact sector, whilst SDSM is likely to underestimate the effects. GPCC performs better than SDSM in reproducing wet and dry day frequency, which is a key advantage for many impact sectors. Overall, the mixed performance of the two methods illustrates the importance of users performing a thorough validation in order to determine the influence of simulated precipitation on their chosen impact sector.

Analysis of electric vehicle charging using the traditional generation expansion planning analysis tool WASP-IV

Electric vehicles (EV) are proposed as a measure to reduce greenhouse gas emissions in transport and support increased wind power penetration across modern power systems. Optimal benefits can only be achieved, if EVs are deployed effectively, so that the exhaust emissions are not substituted by additional emissions in the electricity sector, which can be implemented using Smart Grid controls. This research presents the results of an EV roll-out in the all island grid (AIG) in Ireland using the long term generation expansion planning model called the Wien Automatic System Planning IV (WASP-IV) tool to measure carbon dioxide emissions and changes in total energy. The model incorporates all generators and operational requirements while meeting environmental emissions, fuel availability and generator operational and maintenance constraints to optimize economic dispatch and unit commitment power dispatch. In the study three distinct scenarios are investigated base case, peak and off-peak charging to simulate the impacts of EV’s in the AIG up to 2025.

Electric vehicles and opportunities to displace tailgate emissions using Smart Charging controls

Under the European Union Renewable Energy Directive each Member State is mandated to ensure that 10% of transport energy (excluding aviation and marine transport) comes from renewable sources by 2020. The Irish Government intends to achieve this target with a number of policies including ensuring that 10% of all vehicles in the transport fleet are powered by electricity by 2020. This paper investigates the impact of the 10% electric vehicle target in Ireland in 2020 using a dynamic programming based long term generation expansion planning model. The model developed optimizes power dispatch using hourly electricity demand curves up to 2020, while incorporating generator characteristics and certain operational requirements such as energy not served and loss of load probability while satisfying constraints on environmental emissions, fuel availability and generator operational and maintenance costs. Two distinct scenarios are analysed based on a peak and off-peak charging regimes in order to simulate the effects of the electric vehicles charging in 2020. The importance and influence of the charging regimes on the amount of energy used and tailgate emissions displaced is then determined.

Efficiency assessment of electricity power generation on Ireland’s Single Electricity Market by Data Envelopment Analysis

The efficiency of generation plants is an important measure for evaluating the operating performance. The objective of this paper is to evaluate electricity power generation by conducting an All-Island-Generator-Efficiency-Study (AIGES) for the Republic of Ireland and Northern Ireland by utilising a Data Envelopment Analysis (DEA) approach. An operational performance efficiency index is defined and pursued for the year 2008. The economic activities of electricity generation units/plants examined in this paper are characterized by numerous input and output indicators. Constant returns to scale (CRS) and variable returns to scale (VRS) type DEA models are employed in the analysis. Also a slacks based analysis indicates the level of inefficiency for each variable examined. The findings from this study provide a general ranking and evaluation but also facilitate various interesting efficiency comparisons between generators by fuel type.

An approach to determine the local boundary of small disturbance voltage stability region in a cut-set power space:基于微扰的割集电压稳定域局部边界求解方法

A new approach to determine the local boundary of voltage stability region in a cut-set power space (CVSR) is presented. Power flow tracing is first used to determine the generator-load pair most sensitive to each branch in the interface. The generator-load pairs are then used to realize accurate small disturbances by controlling the branch power flow in increasing and decreasing directions to obtain new equilibrium points around the initial equilibrium point. And, continuous power flow is used starting from such new points to get the corresponding critical points around the initial critical point on the CVSR boundary. Then a hyperplane cross the initial critical point can be calculated by solving a set of linear algebraic equations. Finally, the presented method is validated by some systems, including New England 39-bus system, IEEE 118-bus system, and EPRI-1000 bus system. It can be revealed that the method is computationally more efficient and has less approximation error. It provides a useful approach for power system online voltage stability monitoring and assessment. This work is supported by National Natural Science Foundation of China (No. 50707019), Special Fund of the National Basic Research Program of China (No. 2009CB219701), Foundation for the Author of National Excellent Doctoral Dissertation of PR China (No. 200439), Tianjin Municipal Science and Technology Development Program (No. 09JCZDJC25000), National Major Project of Scientific and Technical Supporting Programs of China During the 11th Five-year Plan Period (No. 2006BAJ03A06). ©2009 State Grid Electric Power Research Institute Press.

The application of a novel fluidised photo reactor under UV-Visible and natural solar irradiation in the photocatalytic generation of hydrogen

With advancements in the development of visible light responsive catalysts for H2 production frequently being reported, photocatalytic water splitting has become an attractive method as a potential ‘solar fuel generator’. The development of novel photo reactors which can enhance the potential of such catalyst, however, is rarely reported. This is particularly important as many reactor configurations are mass transport limited, which in term limits the efficiency of more effective photocatalysts in larger scale applications. This paper describes the performance of a novel fluidised photo reactor for the production of H2 over two catalysts under UV-Visible light and natural solar illumination. Catalysts Pt-C3N4 and NaTaO3.La were dispersed in the reactor and the rate of H2 was determined by GC-TCD analysis of the gas headspace. The unit was an annular reactor constructed from stainless steel 316 and quartz glass with a propeller located in the base to control fluidisation of powder catalysts. Reactor properties such as propeller rotational speed were found to enhance the photo activity of the system through the elimination of mass transport limitations and increasing light penetration. The optimum conditions for H2 evolution were found to be a propeller rotational speed of 1035 rpm and 144 W of UV-Visible irradiation, which produced a rate of 89 µmol h-1 g-1 over Pt-C3N4. Solar irradiation was provided by the George Ellery Hale Solar Telescope, located at the California Institute of Technology.

Stochastic analysis of seepage under water-retaining structures

This paper investigated the problem of confined flow under dams and water retaining structuresusing stochastic modelling. The approach advocated in the study combined a finite elementsmethod based on the equation governing the dynamics of incompressible fluid flow through aporous medium with a random field generator that generates random hydraulic conductivity basedon lognormal probability distribution. The resulting model was then used to analyse confined flowunder a hydraulic structure. Cases for a structure provided with cutoff wall and when the wall didnot exist were both tested. Various statistical parameters that reflected different degrees ofheterogeneity were examined and the changes in the mean seepage flow, the mean uplift forceand the mean exit gradient observed under the structure were analysed. Results reveal that underheterogeneous conditions, the reduction made by the sheetpile in the uplift force and exit hydraulicgradient may be underestimated when deterministic solutions are used.

Introducing the CTA concept

The Cherenkov Telescope Array (CTA) is a new observatory for very high-energy (VHE) gamma rays. CTA has ambitions science goals, for which it is necessary to achieve full-sky coverage, to improve the sensitivity by about an order of magnitude, to span about four decades of energy, from a few tens of GeV to above 100 TeV with enhanced angular and energy resolutions over existing VHE gamma-ray observatories. An international collaboration has formed with more than 1000 members from 27 countries in Europe, Asia, Africa and North and South America. In 2010 the CTA Consortium completed a Design Study and started a three-year Preparatory Phase which leads to production readiness of CTA in 2014. In this paper we introduce the science goals and the concept of CTA, and provide an overview of the project. © 2013 Elsevier B.V. All rights reserved.

Implementation of a cogeneration plant for a food processing facility. A case study

The present work presents an investigation regarding the feasibility analysis of a cogeneration plant for a food processing facility with the aim to decrease the cost of energy supply. The monthly electricity and heat consumption profiles are analyzed, in order to understand the consumption profiles, as well as the costs of the current furniture of electricity and gas. Then, a detailed thermodynamic model of the cogeneration cycle is implemented and the investment costs are linked to the thermodynamic variables by means of cost functions. The optimal electricity power of the co-generator is determined with reference to various investment indexes. The analysis highlights that the optimal dimension varies according to the chosen indicator, therefore it is not possible to establish it univocally, but it depends on the financial/economic strategy of the company through the considered investment index.

Ultrastructure and phylogeny of peridinioid dinoflagellates

Os dinoflagelados são um grupo muito diverso de protistas que possuem um conjunto de características pouco comuns. Os peridinióides são dinoflagelados com teca que é formada por seis séries latitudinais de placas, incluindo a série cingular e um anel incompleto de placas intercalares anteriores, embora as últimas estejam ausentes em algumas espécies de Peridiniopsis. São dinoflagelados com simetria bilateral em relação ao plano apical que contem o eixo dorso-ventral. Na série sulcal há apenas uma placa posterior que contacta com o limite ventral de duas grandes placas antapicais. Entre os peridinióides, a presença ou ausência de um poro apical e o número de placas no cíngulo são geralmente consideradas marcas filogenéticas importantes ao nível de género ou família. Actualmente, a definição de Peridinium Ehrenberg, o dinoflagelado mais comum de água doce, inclui organismos com combinações diferentes destas duas características. Trabalhos anteriores sobre a ultrastrutura e afinidade filogenética das espécies tipo de Peridinium, P. cinctum, e Peridiniopsis Lemmermann, P. borgei também sugerem a necessidade de reexaminar as relações taxonómicas dos peridinióides. Esta tese combina o estudo ultrastrutural de uma selecção de espécies com hipóteses filogenéticas baseadas nas sequências de LSU rDNA, para aumentar o nosso conhecimento das diferenças e afinidades dentro dos peridinióides. Tem como objectivo aumentar o nosso conhecimento das características individuais das células que possam levar a reconhecer sinapomorfias que possam ser usadas como marcadores dos peridinióides como um todo e dos seus subgrupos. As espécies escolhidas para exame pormenorizado foram: Peridinium palatinum Lauterborn, de um grupo com duas placas intercalares anteriores, seis placas cingulares e sem poro apical; Peridinium lomnickii Wo!oszy"ska, de um grupo com poro apical, três placas intercalares e seis cingulares; Peridiniopsis berolinensis (Lemmermann) Bourrelly, uma espécie heterotrófica com poro apical, sem placas intercalares e com seis placas cingulares; e Sphaerodinium cracoviense Wo!oszy"ska, um membro de um género de formas com teca com um tipo de tabulação marginalmente peridinióide, com um suposto poro apical e quatro placas intercalares anteriores. Peridinium palatinum difere de Peridinium e Peridiniopsis típicos, quer em características da teca, quer internas. As diferenças estimadas entre as sequências parciais de LSU rDNA de P. palatinum e a espécie próxima P. pseudolaeve, relativamente a P. cinctum são comparativamente grandes e, juntamente com a topologia da árvore filogenética, apoiam a separação de P. palatinum e formas próximas ao nível de género. Palatinus nov. gen. foi, então, descrito com as novas combinações Palatinus apiculatus nov. comb. (espécie tipo; sin. Peridinium palatinum), P. apiculatus var. laevis nov. comb. e P. pseudolaevis nov. comb.. As características distintivas de Palatinus incluem uma superfície das placas lisa ou um tanto granulosa, mas não areolada, um grande pirenóide central penetrado por canais citoplasmáticos e de onde radiam lobos plastidiais, e a presença de uma fiada microtubular homóloga à de um pedúnculo. As células de Palatinus saem da teca pela zona antapicalpos- cingular. Peridinium lomnickii apresenta tabulação semelhante às formas marinhas, produtoras de quistos calcários, do género Scrippsiella A.R. Loeblich. Para comparação, adicionámos novas observações ultrastruturais de S. trochoidea. Peridinium lomnickii tem uma combinação de características diferente de Peridinium, Peridiniopsis e Scrippsiella. As hipóteses filogenéticas baseadas em DNA colocam P. lomnickii no mesmo ramo que Pfiesteria Steidinger et Burkholder, Tyrannodinium e outras Pfiesteriaceae, com as quais partilha um "microtubular basket" e uma ligação peculiar entre duas placas do sulco. As características distintivas do novo género proposto Chimonodinium gen. ined. incluem, além da tabulação, a ausência de pirenóides, a presença de um "microtubular basket" com quatro ou cinco fiadas sobrepostas de microtúbulos associados a um pequeno pedúnculo, um sistema pusular com tubos pusulares bem definidos ligados aos canais flagelares, e a produção de quistos não calcários. Peridiniopsis berolinensis partilha várias características significativas com Pfiesteria e afins, como um "microtubular basket" com a capacidade de suportar um tubo de alimentação, quimiossensibilidade para encontrar presas apropriadas, o modo de natação junto às presas e a organização geral da célula. Hipóteses filogenéticas com base em LSU rDNA confirmam a afinidade entre P. berolinensis e Pfiesteria bem como a relação mais remota com a espécie tipo de Peridiniopsis, P. borgei. Estas razões justificam a proposta de Tyrannodinium gen. nov., uma nova Pfiesteriaceae que difere de outros membros do grupo por viver em água doce e nos pormenores da tabulação. Sphaerodinium cracoviense revelou a tabulação típica do género Sphaerodinium, que apresenta um número de placas intercalares superiores e pos-cingulares maior que o que é típico em peridinióides: 4 e 6, respectivamente. Observações em SEM mostraram uma estrutura apical diferente da dos peridinióides, e um sulco apical numa das placas fazendo lembrar a área apical de alguns woloszynskióides. Os pormenores do aparelho flagelar e do sistema pusular ligam o Sphaerodinium aos woloszynskióides em geral e ao género Baldinia em particular, mas não aos peridinióides. O volumoso estigma de S. cracoviense revelou ser extraplastidial e de um modelo único, composto por elementos que se encontram em woloszynskióides, mas nunca encontrados anteriormente juntos. A análise filogenética baseada nas sequências parciais de LSU rDNA também sugerem uma maior proximidade de S. cracoviense com os woloszynskióides do que com os peridinióides. Futuras análises pormenorizadas de dinoflagelados peridinióides, em especial entre os do numeroso grupo de espécies com poro apical, serão necessárias para clarificar as suas relações taxonómicas; e a produção de descrições melhoradas das características finas particulares das células serão um requisito para perceber a evolução dos caracteres dos peridinióides por forma a podermos identificar marcadores filogenéticos.