Modificação superficial do tecido 100% algodão tratado com plasma

The 100% cotton fabric (CO)* treated with plasma of methane CH4 has direct application in all areas that needs of aqueous solutions repellent material like coatings and uniforms applied biomedical, aeronautics, and automobile between others. 100% cotton fabric (CO) samples were treated by plasma with two differents atmosphere: Methane gas (CH4), treatment time was varied in 10 in 10 min. until 60 min., and mixture methane/argon (CH4/Ar), it was varied the proportion 1:9, 2:8, 3:7, 4:6, 5:5, 6:4, 7:3, 8:2 e 9:1, with treatment time of 30 minutes. In both, the fluxe was 5 sccm (second cubic centimeter), pressure 6 mbar, voltage 490 V and current 0,15A. The objective of work was measure the superficial tension of 100% CO then it treated with plasma, using contact angle measures of water and glycerol with the surface. The samples were tested after treatment, with 8 and 12 months to verify the superficial modification effects. It was verified an increase of hydrophobility with the Sessile drop values varied between 116,69º to 137,85º and it carried on after 12 months. The no treated samples shows contact angle equal 0º. OES analysis and Raman spectroscopy were accomplished. In the SEM analysis was verified oligomers. The plasma treatment is correct environmental, It turning greater than conventional treatments

Nutrient extraction and exportation by castor bean hybrid lyra

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito da adubação fosfata sobre o acúmulo de biomassa e teor de brix de duas variedades de cana-de-açúcar

The objective of this study was to evaluate the accumulation of matter, dry matter content of Brix and two varieties of sugar cane, influenced by the phosphorus cultivated on "Zona da Mata" region, State of Alagoas. The experiment, a factorial 2 x 6, was composed of two varieties of cane; RB867515 and RB92579 and six phosphorus levels: zero, 30, 60, 90, 120 and 150 kg ha(-1), with the source of the phosphorus triple superphosphate. Was also used nitrogen and potassium in doses equivalent to 100 and 200 kg ha(-1) and K, respectively. The soil of the experimental area was set to raise the base saturation to 60%. At the beginning of the first rainfall of the rainy season of 2006 was performed with micro fertilization in coverage, in doses equivalent to 6,0; 6,0 and 7,0 kg ha(-1) of Cu, Zn and Mn, respectively. Was The chemical control of weeds. Every month, from August to October 2006, samples were collected in the cane plant. There was initially the number of plants m(2), followed by weighing the material. It was subsequently withdrawn a subsample containing ten plants for weighing. After weighing the material was passed in horsemanship and homogenized, again drew up a sample of approximately 300g, leading them to forced ventilation oven at 65 degrees C, toobtain constant weight. Resulting in the production of natural (MN) and dry matter (DM). In July, we analyzed the levels of Brix% juice in the refractometer Brix. The average values of production of natural (MN), dry matter (DM) and contents of Brix% were subjected to analysis of variance and regression for variables. The accumulation of dry matter and were influenced by fertilization. The contents of Brix% in two varieties did not suffer significant influence of fertilization.

Análise de viabilidade técnica de utilização da Fibra de bananeira com resina sintética em Compósitos

This paper aims to present the feasibility of using a composite using discarded material from the cultivation of banana tree (pseudostem), which is fibrillated together with synthetic resin replacing glass fiber to be used in structural elements that do not demand large mechanical stress such as reservoirs, troughs, domes, sewage pipes etc.. For this, there were studies about the mechanical properties of a composite made with polyester resin and fiber of banana tree (Musa sp, musac), in which the splints were removed from the pseudostem, being made fibrillation by hand, with the aid of a brush steel, followed by natural drying. After treatment for cleaning and removal of wax, the fiber was cut into pieces of approximately 60 mm to 100 mm, for, together with synthetic resin, make cards of a features fiber composite with random orientation relative to the weight of the resin. We used three different percentages of fiber (3%, 6% and 9%), in order to make a comparative study between them and what would be the one with the best performance. Were manufactured specimens of each material and then subjected to uniaxial tensile tests, three point bending, moisture absorption and thermal characteristics. The results show that, in general, the use of banana tree fiber is feasible simply by an improvement in the production process (machining of the procedure) and greater care in the manufacture of parts

Influência da umidade nas propriedades mecânicas dos compósitos poliméricos híbridos (sisal/ vidro)

This study aims to evaluate the mechanical properties of polymer matrix composites reinforced with sisal fabric bidirectional tissue (Agave sisalana,) and E-glass fibers, containing the following configuration: a polymer matrix hybrid composite (Polyester Resin orthophalic) reinforced with three (3) layers of glass fibers and alternating-2 (two) layers of bidirectional sisal fabric, and finally a composite of polymer matrix reinforced with five (5) layers of glass fiber mat-type E. For this purpose as first step, the preparation of by sisal, since they are not on the market. The composites were made by manual lamination (Hand lay-up) and evaluated for tensile properties and three point bending both in the dry, and wet conditions aswele as immersed in oil. Macroscopic and microscopic characteristics of the materialsweve awalysed, after the completion of the mechanical tests. After the studies, it was proven that the sisal fiber decreases the tensile stiffness of the material above 50% for both situations studied the tensile strength of the material decreases by approximately 40% for the cases mentioned, and when compared to the specific strength stiffness values drop to 14.6% and 29.02% respectively for the dry state only. Constants for bending the values were are to approximately 50% to 25% for strength and stiffness of the material for the cases dry, wet and immersed in oil. Under the influence of tension fluids do not interfere in the stiffness of the material for the bending tests, the same does not occur with the resistance, and these values are modified only in the cases stiffness and flexural strength

Desenvolvimento de mudas de Tabeluia chrysotricha em função de substratos e de soluções de fertirrigação

The work aimed to study the development of Tabebuia chrysotricha Standl. seedlings injunction of different substrate and different fertilization solutions. To compose the substrate it was used fibrous and granulated coconut fiber obtaining the following treatments: S1- 100% fibrous, S2- 60% fibrous and 40% granulated, S3- 40% fibrous and 60% granulated and S4- 100% granulated. The basis fertilization was the same for all treatments and the solutions of fertilization varied in order to obtain solutions with the following electric conductivities: EC1- 1.06 dS m(-1), EC2- 2.12 dS m(-1), EC3- 3.2 dS m(-1) and EC4- 4.25 dS m(-1). The propagative material was sowed directly in plastic containers (120mL) with the respective substrates. The fertilization was received through sub irrigation once a week, until the seedlings reached 20cm of height approximately. The chemical analyses of the substrate (EC and pH), through aqueous extraction method 1:1.5 (1 substrate: 1.5 deionized water), the analyses of aerial part height, stein diameter and pairs true leaves number, as well as the weight of total dry, matter, were accomplished each 15 days. In almost every analysis, the substrate with granulated coconut fiber, as well as the smallest EC (1.06 e 2.12 dS m(-1)) of fertilization solutions,formed seedlings with higher averages, indicating faster growth. In the conditions of this experiment, the production of T. chrysotricha seedlings was better in granulated coconut fiber substrate and fertilizer solutions with EC of 1.06 dS m(-1), appreciating the estimated characteristics.

Bio-óleo e biogás da degradação termoquímica de lodo de esgoto doméstico em cilindro rotativo

The objective of this study was to produce biofuels (bio-oil and gas) from the thermal treatment of sewage sludge in rotating cylinder, aiming industrial applications. The biomass was characterized by immediate and instrumental analysis (elemental analysis, scanning electron microscopy - SEM, X-ray diffraction, infrared spectroscopy and ICP-OES). A kinetic study on non-stationary regime was done to calculate the activation energy by Thermal Gravimetric Analysis evaluating thermochemical and thermocatalytic process of sludge, the latter being in the presence of USY zeolite. As expected, the activation energy evaluated by the mathematical model "Model-free kinetics" applying techniques isoconversionais was lowest for the catalytic tests (57.9 to 108.9 kJ/mol in the range of biomass conversion of 40 to 80%). The pyrolytic plant at a laboratory scale reactor consists of a rotating cylinder whose length is 100 cm with capable of processing up to 1 kg biomass/h. In the process of pyrolysis thermochemical were studied following parameters: temperature of reaction (500 to 600 ° C), flow rate of carrier gas (50 to 200 mL/min), frequency of rotation of centrifugation for condensation of bio-oil (20 to 30 Hz) and flow of biomass (4 and 22 g/min). Products obtained during the process (pyrolytic liquid, coal and gas) were characterized by classical and instrumental analytical techniques. The maximum yield of liquid pyrolytic was approximately 10.5% obtained in the conditions of temperature of 500 °C, centrifugation speed of 20 Hz, an inert gas flow of 200 mL/min and feeding of biomass 22 g/min. The highest yield obtained for the gas phase was 23.3% for the temperature of 600 °C, flow rate of 200 mL/min inert, frequency of rotation of the column of vapor condensation 30 Hz and flow of biomass of 22 g/min. The non-oxygenated aliphatic hydrocarbons were found in greater proportion in the bio-oil (55%) followed by aliphatic oxygenated (27%). The bio-oil had the following characteristics: pH 6.81, density between 1.05 and 1.09 g/mL, viscosity between 2.5 and 3.1 cSt and highest heating value between 16.91 and 17.85 MJ/ kg. The main components in the gas phase were: H2, CO, CO2 and CH4. Hydrogen was the main constituent of the gas mixture, with a yield of about 46.2% for a temperature of 600 ° C. Among the hydrocarbons formed, methane was found in higher yield (16.6%) for the temperature 520 oC. The solid phase obtained showed a high ash content (70%) due to the abundant presence of metals in coal, in particular iron, which was also present in bio-oil with a rate of 0.068% in the test performed at a temperature of 500 oC.

Estudo da remoção de Ba2+, Ni2+, Cd2+, Cu3+, Cr3+, Sr2+, Zn2+ por eletrocoagulação em água associada à produção de petróleo

Among the waste generated in the petrochemical industry water associated with oil production is the most important. It is considered one of the great challenges due to the presence of considered toxic chemicals present in this composition. The presence of these substances difficult to reuse the water associated with the enhanced recovery processes, so that prior to their reuse or disposal, treatment is necessary. This paper aimed to study the removal efficiency of chemical species: Ba2+, Ni2+, Cd2+, Cu2+, Cr3+, Sr2+ and Zn2+, present in the composition of the water associated with oil production by electrocoagulation. The evaluation of removal of these chemical species was performed by laboratory tests using electrochemical batch reactors and continuous flow. Initial tests were performed with electrocoagulation of synthetic wastewater in batch reactor using iron electrode. Results of removal of Zn2+ and Ni2+ were 78 % and 59 % respectively. While the percentage of removed Ba2+ was 19 % by 30 minutes of treatment and by applying current of 1.10 A. The tests were performed on effluent batch reactor applying the electrochemical technique with stainless steel electrodes 304, the objective was to remove part of the dispersed oil and also of organic compounds in the effluent. Under the experimental conditions used, the maximum result was obtained TOG was 60 % and TOC was approximately 50 % compared to the initial concentration. In the experiments carried out in continuous reactor, with effluent semisynthetic, have been used electrodes of iron and aluminum and the results were 100 % removal of Cd2+, Cu2+, Cr3+ and Zn2+ and 77 % of Sr2+. These percentages were only attainable through the use of the iron electrode. However, when the electrode was replaced by aluminum, there was a reduction in the percentage of removal to 65 %, using the same flow rate and current. Therefore according to the results obtained using the iron electrode was more effective in removing these metals and the conditions of lower current and lower flow rate was satisfactory, as observed in the experimental design adopted

Avaliação do crescimento de ocupação da bacia do rio Pitimbu com subsídios para estudos de possíveis impactos sobre os recursos hidricos

The Pitimbu River Watershed (PRW), belonging to Potiguar capital metropolitan area, State of Rio Grande do Norte, contributes, among other purposes, to human using and animal watering. This watershed is extremely important because, besides filling up with freshwater approximately 30% of the south part of Natal (South, East and West Zones), contributes to the river shore ecosystem equilibrium. Face to the current conjuncture, this study aims to evaluate the urban development dynamics in the PRW, applying Cellular Automata as a modeling instrument, and to simulate future urban scenarios, between 2014 and 2033, using the simulation program SLEUTH. In the calibration phase, urban spots for 1 984, 1992, 2004 and 2013 years were used, with resolution from 100 meters. After the simulation, it was found a predominance of organic growth, expanding the BHRP from existing urban centers. The spontaneous growth occurred through the fullest extent of the watershed, however the probability of effective growth should not exceed 21%. It was observed that, there was a 68% increase for the period between 2014 and 2033, corresponding to an expansion area of 1,778 ha. For 2033, the source of Pitimbu River area and the Jiqui Lake surroundings will increase more than 78%. Finally, it was seen an exogenous urban growth tendency in the watershed (outside-in). As a result of this growth, hydraulics resources will become scarcer

Recombinant expression of glycerol-3-phosphate dehydrogenase using the Pichia pastoris system

In the present study, the GPD2 gene from Saccharomyces cerevisiae, which codifies for the enzyme glycerol-3-phosphate dehydrogenase (GPDH), was cloned from the pPICZ-alpha expression vector and used with the purpose of inducing the extracellular expression of the glycerol-3-phosphate dehydrogenase under the control of the methanol-regulated AOX promoter. The presence of the GPD2 insert was confirmed by PCR analysis. Pichia pastoris X-33 (Mut(+)) was transformed with linearized plasmids by electroporation and transformants were selected on YPDS plates containing 100 mu g/mL of zeocin. Several clones were selected and the functionality of this enzyme obtained in a culture medium was assayed. Among the mutants tested, one exhibited 3.1 x 10(-2) U/mg of maximal activity. Maximal enzyme activity was achieved at 6 days of growth. Medium composition and pre-induction osmotic stress influenced protein production. Pre-induction osmotic stress (culturing cells in medium with either 0.35 M sodium chloride or 1.0 M sorbitol for 4h prior to induction) led to an increase in cell growth with sorbitol and resulted in a significant increase in GPDH productivity with sodium chloride in 24h of induction approximately fivefold greater than under standard conditions (without pre-induction). (C) 2010 Elsevier B.V. All rights reserved.

Anisotropia magnética (110) em Nanofilmes de Permalloy sobre MgO(100)

The study and fabrication of nanostructured systems composed of magnetic materials has been an area of great scientific and technological interest. Soft magnetic materials, in particular, have had great importance in the development of magnetic devices. Among such materials we highlight the use of alloys of Ni and Fe, known as Permalloy. We present measurement results of structural characterization and magnetic films in Permalloy (Ni81Fe19), known to be a material with high magnetic permeability, low coercivity and small magneto- crystalline anisotropy, deposited on MgO (100) substrates. The Magnetron Sputtering technique was used to obtain the samples with thicknesses varying between 9 150 nm. The techniques of X- ray Diffraction at high and low angle were employed to confirm the crystallographic orientation and thickness of the films. In order to investigate the magnetic properties of the films the techniques of Vibrant Sample Magnetometry (VSM), Ferromagnetic Resonance (FMR) and Magnetoimpedance were used. The magnetization curves revealed the presence of anisotropy for the films of Py/MgO (100), where it was found that there are three distinct axis - an easy-axis for θH = 0°, a hard-axis for θH = 45° and an intermediate for θH = 90°. The results of the FMR and Magnetoimpedance techniques confirm that there are three distinct axes, that is, there is a type C2 symmetry. Then we propose, for these results, the interpretation of the magnetic anisotropy of Py/MgO ( 100 ) is of type simple C2, ie a cubic magnetic anisotropy type ( 110 )

Crescimento de filmes nanométricos monocristalinos de Fe/MgO(100) por "SPUTTERING" DC

The research behind this master dissertation started with the installation of a DC sputtering system, from its first stage, the adaptation of a refrigerating system, passing by the introduction of a heating system for the chamber using a thermal belt, until the deposition of a series of Fe/MgO(100) single crystal nanometric film samples. The deposition rates of some materials such as Fe, Py and Cu were investigated through an Atomic Force Microscope (AFM). For the single crystal samples, five of them have the same growth parameters and a thickness of 250Å, except for the temperature, which varies from fifty degrees from one to another, from 100ºC to 300ºC. Three other samples also have the same deposition parameters and a temperature of 300ºC, but with thickness of 62,5Å, 150Å, and 250Å. Magneto-optical Kerr Effect (MOKE) of the magnetic curves measurements and Ferromagnetic Resonance (FMR) were made to in order to study the influence of the temperature and thickness on the sample s magnetic properties. In the present dissertation we discuss such techniques, and the experimental results are interpreted using phenomenological models, by simulation, and discussed from a physical point of view, taking into account the system s free magnetic energy terms. The results show the growth of the cubic anisotropy field (Hac) as the sample s deposition temperature increases, presenting an asymptotic behavior, similar to the characteristic charging curve of a capacitor in a RC circuit. A similar behavior was also observed for the Hac due to the increase in the samples thicknesses. The 250˚A sample, growth at 300°C, presented a Hac field close to the Fe bulk value

Ferroelectric and piezoelectric properties of bismuth layered thin films grown on (100) Pt electrodes

The effect of film orientation on piezoelectric and ferroelectric properties of bismuth layered compounds deposited on platinum coated silicon substrates was investigated. Piezo-force microscopy was used to probe the local piezoelectric properties of Bi(4)Ti(3)O(12), CaBi(4)Ti(4)O(15) and SrBi(4)Ti(4)O(15) films. Our measurements on individual grains clearly reveal that the local piezoelectric properties are determined by the polarization state of the grain. A piezoelectric coefficient of 65 pm/V was attained after poling in a grain with a polar axis very close to the normal direction. The piezoelectric coefficient and the remanent polarization were larger for a-b axes oriented than for c-axis-oriented films. (c) 2007 Elsevier B.V All rights reserved.

Enhanced ferroelectric properties of La-substituted BiFeO3 thin films on LaSrCoO3/Pt/TiO2/SiO2/Si (100) substrates prepared by the soft chemical method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Distribuição espacial de Tenuipalpus heveae Baker (Acari: Tenuipalpidae) na cultura da seringueira

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)