On the results of preliminary fishing trials with shark long lines in Veraval waters

Experimental fishing operations with shark long lines were conducted in the sea off Veraval with a view to studying their efficiency and gathering information on the available resources of sharks to be used for planning the future gear investigations. The trials were undertaken in 1967, employing departmental fishing vessel "Fishtech No. IV" (10.9 m O.L. and 48 H.P. engine). A total of 5525 hooks were employed and 242 sharks weighing 8629 kg were landed. Data on composition of catch, weight of fishes landed, effectiveness of various baits in capture of different species of sharks and effectiveness of gear including its catch efficiency in this area were compiled. Bait preference was also observed in certain species of sharks caught. Chirocentrus dorab proved to be the cheapest and most effective bait in capture of all the three varieties of sharks landed.

A discrete dislocation analysis of fatigue crack growth

Cyclic loading of a plane strain mode I crack under small scale yielding is analyzed using discrete dislocation dynamics. The dislocations are all of edge character, and are modeled as line singularities in an elastic solid. At each stage of loading, superposition is used to represent the solution in terms of solutions for edge dislocations in a half-space and a non-singular complementary solution that enforces the boundary conditions, which is obtained from a linear elastic, finite element solution. The lattice resistance to dislocation motion, dislocation nucleation, dislocation interaction with obstacles and dislocation annihilation are incorporated into the formulation through a set of constitutive rules. An irreversible relation between the opening traction and the displacement jump across a cohesive surface ahead of the initial crack tip is also specified, which permits crack growth to emerge naturally. It is found that crack growth can occur under cyclic loading conditions even when the peak stress intensity factor is smaller than the stress intensity required for crack growth under monotonic loading conditions; however below a certain threshold value of ΔKI no crack growth was seen.

East African Freshwater Fisheries Research Organization Annual Report 1972

Feeding habits of many animals have been used widely in animal classifications. This is so, because the type of diet an organism requires demands structural specialisation which will utilise the available resource. Many animals may however have many structural modifications to enable them to be described as omnivourous or generalised feeders such as H. empodisma and H. riponianus (GREENWOOD 1960) which may show varying degrees of structural and adaptational intermediacy between two trophic groups. Generally, however, the diet of many animals including fish changes as the animal grow larger. The change in structural modifications is usually correlated with changes in the diet. In fishes the change may involve change from tricuspid to biscuspid and finally to unicuspid type of teeth. The degree of modification in the structure depends on the diet, thus Haplochromis that feeds on soft tissues of snails only requires modifications in oral dentition while Haplochromis that feeds on both soft tissues and shells of snails require modification in the lower pharyngeal bone for grinding purposes. Other modifications connected with food utilisation may be located in the alimentary canal. (I) The fish species that are commercially exploited are Protopterus aethiopicus, Clarias mossambicus, Tilapia esculenta, Tilapia amphimelas and Tilapia hybrids. The other fish species present in the lake but not commercially exploited are: Gnathonemus sp. Alestes sp. Labeo sp., Barbus paludinoses, Barbus jacksoni, Barbus lineomaculatus, Barbus regersi, Leptogrlanis sp., Schilbe sp., Haplochromis spp. and Hemihaplochromis sp. (2) Protopterus sp. and Clarias sp. are mostly caught with hooks on long lines. There has been a steady increase in number of hooks on the lake. Since the stocks of Protopterus and C/arias in the lake have a limit, we should control the number of hooks used by each of the fishermen in order to avoid overharvesting. (3) All the previous studies on Lake Kitangiri fisheries suggested the use of gill nets with mesh size greater than 88.9 mm in order to avoid the capture of immature Ti/apia spp. But if the fishermen are to obtain economic gains from the fishery, the optimum mesh size for use is 88.9 -101.6 mm. (4) The gillnet is a passive gear with very beneficial selective characteristics. Unfortunately the drive-in fishery which exists on Lake Kitangiri more or less destroys the gillnet selectivity characteristics. It is therefore recommended that the beating of water with poles be discouraged and stopped. (5) There is need for provision of stable fishing canoes to replace the unstable bottle palm dug-out canoes which are currently being used and which are very risky to operate. (6) The fish processing facilities on Lake Kitangiri are still inadequate. Most of the fish is sun dried, Since sun drying is very difficult during the rainy season, most fishermen carry out intensive fishing during the dry season, Concentrating most of the fishing effort in anyone season instead of spreading evenly this effort over the whole year could damage the age structure of the exploitable stocks. (7) There are considerable fluctuations in the volume of water of the lake. The feasibility of regulating the water loss through the effluent Sibiti river should be investigated by the Water Development Department. (8) Damming the Sibiti river is an expensive undertaking and therefore, the Rural Development Bank of Tanzania should be asked to assess the economic feasibility of such a project.

The effect of work processes on the casing heat transfer of a transonic turbine

This paper considers the effect of the rotor tip on the casing heat load of a transonic axial flow turbine. The aim of the research is to understand the dominant causes of casing heat-transfer. Experimental measurements were conducted at engine-representative Mach number, Reynolds number and stage inlet to casing wall temperature ratio. Time-resolved heat-transfer coefficient and gas recovery temperature on the casing were measured using an array of heat-transfer gauges. Time-resolved static pressure on the casing wall was measured using Kulite pressure transducers. Time-resolved numerical simulations were undertaken to aid understanding of the mechanism responsible for casing heat load. The results show that between 35% and 60% axial chord the rotor tip-leakage flow is responsible for more than 50% of casing heat transfer. The effects of both gas recovery temperature and heat transfer coefficient were investigated separately and it is shown that an increased stagnation temperature in the rotor tip gap dominates casing heat-transfer. In the tip gap the stagnation temperature is shown to rise above that found at stage inlet (combustor exit) by as much as 35% of stage total temperature drop. The rise in stagnation temperature is caused by an isentropic work input to the tip-leakage fluid by the rotor. The size of this mechanism is investigated by computationally tracking fluid path-lines through the rotor tip gap to understand the unsteady work processes that occur. Copyright © 2005 by ASME.

Discrete dislocation plasticity analysis of crack-tip fields in polycrystalline materials

Small scale yielding around a mode I crack is analysed using polycrystalline discrete dislocation plasticity. Plane strain analyses are carried out with the dislocations all of edge character and modelled as line singularities in a linear elastic material. The lattice resistance to dislocation motion, nucleation, interaction with obstacles and annihilation are incorporated through a set of constitutive rules. Grain boundaries are modelled as impenetrable to dislocations. The polycrystalline material is taken to consist of two types of square grains, one of which has a bcc-like orientation and the other an fcc-like orientation. For both orientations there are three active slip systems. Alternating rows, alternating columns and a checker-board-like arrangement of the grains is used to construct the polycrystalline materials. Consistent with the increasing yield strength of the polycrystalline material with decreasing grain size, the calculations predict a decrease in both the plastic zone size and the crack-tip opening displacement for a given applied mode I stress intensity factor. Furthermore, slip-band and kink-band formation is inhibited by all grain arrangements and, with decreasing grain size, the stress and strain distributions more closely resemble the HRR fields with the crack-tip opening approximately inversely proportional to the yield strength of the polycrystalline materials. The calculations predict a reduction in fracture toughness with decreasing grain size associated with the grain boundaries acting as effective barriers to dislocation motion.

Co-expression of CD173 (H2) and CD174 (Lewis Y) with CD44 suggests that fucosylated histo-blood group antigens are markers of breast cancer-initiating cells

Histo-blood group antigens CD173 (H2) and CD174 (Lewis Y) are known to be developmentally regulated carbohydrate antigens which are expressed to a varying degree on many human carcinomas. We hypothesized that they might represent markers of cancer-initiating cells (or cancer stem cells, CSC). In order to test this hypothesis, we examined the co-expression of CD173 and CD174 with stem cell markers CD44 and CD133 by flow cytometry analysis, immunocytochemistry, and immunohistochemistry on cell lines and tissue sections from breast cancer. In three breast cancer cell lines, the percentage of CD173(+)/CD44(+) cells ranged from 17% to > 60% and of CD174(+)/CD44(+) from 21% to 57%. In breast cancer tissue sections from 15 patients, up to 50% of tumor cells simultaneously expressed CD173, CD174, and CD44 antigens. Co-expression of CD173 and CD174 with CD133 was also observed, but to a lesser percentage. Co-immunoprecipitation and sandwich ELISA experiments on breast cancer cell lines suggested that CD173 and CD174 are carried on the CD44 molecule. The results show that in these tissues CD173 (H2) and CD174 (LeY) are associated with CD44 expression, suggesting that these carbohydrate antigens are markers of cancer-initiating cells or of early progenitors of breast carcinomas.

Standardisation of specification for different trolling lures

Fishing experiments were conducted with buffalo horn, wooden and galvanised iron jigs of different lengths and weights rigged in troll lines. It was observed that jigs with 12 cm length and 60 g weight were superior to others in luring seer fish. Fish head jigs of 60 g weight showed a higher efficiency index than those of 50 and 70 g tried in these studies.