High strength Ni based composite reinforced by solid solution W(Al) obtained by powder metallurgy

The solid-solution-particle reinforced W(Al)-Ni composites were successfully fabricated by using mechanical alloying (MA) and hot-pressing (HP) technique when the content of Ni is between 45 wt% and 55 wt%. Besides, samples of various original component ratio of Al50W50 to Ni have been fabricated, and the corresponding microcomponents and mechanical properties such as microhardness, ultimate tensile strength and elongation were characterized and discussed. The optimum ultimate tensile strength under the experiment conditions is 1868 MPa with elongation of 10.21 % and hardness of 6.62 GPa. X-ray diffraction (XRD), FE-SEM and energy dispersive analysis of X-rays (EDS) were given to analysis the components and morphology of the composite bulk specimens.

Fe(acac)_3-Al(i-Bu)_3对马来酸酐与茴香脑共聚的催化性能

研究了Fe(acac) 3 Al(i Bu) 3 (acac =乙酰丙酮 )催化体系对马来酸酐 (MA)与茴香脑 (ANE)共聚反应的催化性能 .动力学研究结果表明 ,MA与ANE共聚对单体的浓度呈一级反应 ,其表观活化能为 31 0kJ/mol.用IR和13 CNMR研究了共聚物的结构 ,结果表明聚合物是交替的 ,其中酸酐的含量为 4 5 6 % .用GPC测定了聚合物的分子量及其分布 ,结果表明分子量的分布较窄 ,PDI =1 19～ 1 4 2 .用DTA研究了聚合物的热力学性质 ,其分解温度为 5 0 1 1℃.

Synthesis, structural characterization and electrical property of new oxide ion conductors: La3MMo2O12 (M = In, Ga and Al)

New series of oxides, La3MMo2O12 (M = In, Ga and Al), have been prepared by the solid-state reaction. The composition and elemental distribution were analyzed by the energy-dispersive X-ray (EDX) analysis. As determined by the X-ray diffraction (XRD), these compounds have similar crystal structures that can be indexed on a monoclinic cell at room temperature. AC impedance spectra and the DC electrical conductivity measurements in various atmospheres indicate that they are oxide ion conductors with ionic conductivities between 10(-2) and 10(-3) S/cm at 800 degrees C. The conductivity decreases in the order of La3GaMo2O12 > La3AlMo2O12 > La3InMo2O12, implying that the effect of cell volume and polarization associated with In3+, Ga3+ and Al3+ play an important role in the anion transport of these materials. The reversible phase transition was observed in all these compounds as confirmed by the differential thermal analysis (DTA) and dilatometric measurements.

Improved performance and stability by an Al/Ni bilayer cathode in organic light-emitting diodes

Al/Ni bilayer cathode was used to improve the electroluminescent (EL) efficiency and stability in N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1' biphenyl 4,4'-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq(3))-based organic light-emitting diodes. The device with LiF/Al/Ni cathode achieved a maximum power efficiency of 2.8 lm/W at current density of 1.2 mA/cm(2), which is 1.4 times the efficiency of device with the state-of-the-art LiF/Al cathode. Importantly, the device stability was significantly enhanced due to the utilization of LiF/Al/Ni cathode. The lifetime at 30% decay in luminance for LiF/Al/Ni cathode was extrapolated to 400 It at an initial luminance of 100 cd/m(2), which is 10 times better than the LiF/Al cathode.

NaCl/Ca/Al as an efficient cathode in organic light-emitting devices

An efficient cathode NaCl/Ca/Al used to improve the performance of organic light-emitting devices (OLEDs) was reported. Standard NM-bis(1-naphthyl)-NAP-diphenyl-1,1' biphenyl 4,4'-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq(3)) devices with NaCl/Ca/Al cathode showed dramatically enhanced electroluminescent (EL) efficiency. A power efficiency of 4.6 lm/W was obtained for OLEDs with 2 nm of NaCl and 10 nm of Ca, which is much higher than 2.0 lm/W, 3.1 lm/W, 2.1 lm/ W and 3.6 lm/W in devices using, respectively, the LiF (1 nm)/Al, LiF (1 nm)/Ca (10 nm)/Al, Ca (10 nm)/Al and NaCl (2 nm)/ Al cathodes. The investigation of the electron injection in electron-only devices indicates that the utilization of the NaCl/Ca/Al cathode substantially enhances the electron injection current, which in case of OLEDs leads to the improvement of the brightness and efficiency.

Fe(2-EHA)(3)/Al(i-Bu)(3)/hydrogen phosphite catalyst for preparing syndiotactic 1,2-polybutadiene

Polymerizing 1,3-butadiene into syndiotactic 1,2-polybutadiene with art iron(III) catalyst system has been investigated. Activity of the catalyst was affected by the type of cocatalyst alkylaluminum and the phosphorus compound as an electron donor, molar ratio of catalyst components, and their aging sequence and aging time of the catalyst. The microstructure and configuration of the polymer was decided by the catalyst components, the higher [Al]/[Fe] molar ratio tending to yield syndiotactic 1,2-polybutadiene, while the higher [P]/[Fe] molar ratio favors the formation of amorphous 1,2-polybutadiene.

新型室温离子液体六烷基胍盐的制备及性质

近年来 ,离子液体 (IL)作为“绿色”溶剂受到学术和工业界的关注 .英国 BP公司和法国的 IFP等研究机构从 2 0世纪 80年代起就开始探索离子液体作为溶剂与催化剂的可能性 ,至今在离子液体体系中已实现了许多催化反应 [1～ 5] .室温离子液体 (RTIL S)是指在常温下呈液态的熔盐体系 .通常由烷基吡啶或双烷基咪唑季铵阳离子与氯铝酸根、氟硼酸根及氟磷酸根等阴离子组成 .在季铵盐类离子液体中 ,咪唑盐的合成和应用研究尤为突出 .目前 ,对于既可作为溶剂又可作为催化剂的室温离子液体的合成和应用已成为研究热点 [6 ] ,如室温离子液体 [EMIM]Cl/Al Cl3已用于芳烃的烷基化反应的溶剂和催化剂[7] .胍盐由于具有较高的热力学稳定性 ,主要用作耐高温相转移催化剂[8] .目前 ,尽管人们对何种结构的化合物能够形成室温离子液体还不完全清楚 ,但在不对称结构中电荷分散程度较高的化合物能够形成室温离子液体 [9] .关于胍盐类型的室温离子液体的研究尚还未见报道 ,我们考虑胍盐的结构中电荷分散程度较高的特点 ,通过适当的分子设计来调节烷基链的长短 ,合成了一类新型室温离子液体——六烷基胍氟硼酸盐

La对Pd/Al/蜂窝陶瓷催化剂高温活性与耐热稳定作用的研究

中国科学院山西煤炭化学研究所

Fe改性工业Cu/Zn/Al催化剂甲醇水蒸气重整反应制氢的研究

中国科学院山西煤炭化学研究所

Preparation of W-Al alloys by mechanical alloying

W1-xAlx (x=0-0.86) alloys were synthesized by mechanically alloying the pure metal powder mixtures at designated compositions by conventional high-energy ball milling. The W-Al alloys were stable under high pressure and high temperature. The alloys were lighter than W. The hardness and oxidation resistance of the alloys was greatly improved compared to both W and Al. (C) 2002 Elsevier Science B.V. All rights reserved.