Characterization of nano-scale particles in hot-rolled, high strength low alloy steels (HSLA)

The contribution of nano-scale particles observed using Atom Probe Tomography in an increase of yield strength of conventional and advanced HSLA steels was studied. The advanced HSLA steel showed higher yield strength than conventional HSLA steel. There were two types of carbides, which primarily contribute to an increase in yield strength of conventional HSLA steel: (i) coarse TiC with average size of 25±5nm and (ii) fine TiC with average radius of 3±1.2nm. The presence of two types of carbides was found in the microstructure of advanced HSLA steel: (i)
nano-scale Ti0.98Mo0.02C0.6 carbides with average radius of 2.2±0.5nm, and (ii) C19Cr7Mo24 particles with an average radius of 1.5±0.3nm. The contribution of precipitation hardening in the yield strength of advanced HSLA steel due to the nano-scale particles was 174MPa, while this value in the conventional HSLA steel was 128MPa.

Effect of process variables on formation of dynamic strain induced ultrafine ferrite during hot torsion testing

Ultrafine grain sizes were produced using hot torsion testing of a 0.11C-1.68Mn-0.20Si (wt-%) steel, with ultrafine ferrite (<1 µm) nucleating intragranularly during testing by dynamic strain induced transformation. A systematic study was made of the effect of isothermal deformation temperature, strain level, strain rate, and accelerated cooling during deformation on the formation of ultrafine ferrite by this process. Decreasing the isothermal testing temperature below the Ae₃ temperature led to a greater driving force for ferrite nucleation and thus more extensive nucleation during testing; the formation of Widmanstätten ferrite prior to, or early during, deformation imposed a lower temperature limit. Increasing the strain above that where ferrite first began 0.8 at 675C and a strain rate of 3 s¯¹ increased the intragranular nucleation of ferrite. Strain rate appeared to have little effect on the amount of ferrite formed. However, slower strain rates led to extensive polygonisation of the ferrite formed because more time was available for ferrite recovery. Accelerated cooling during deformation followed by air cooling to room temperature led to a uniform microstructure consisting of very fine ferrite grains and fine spherical carbides located in the grain boundaries regions. Air cooling after isothermal testing led to carbide bands and a larger ferrite grain size.

The production of ultrafine ferrite during hot torsion testing of a 0.11 Wt Pct C steel

Ultrafine ferrite grain sizes were produced in a 0.11C-1.6Mn-0.2Si steel by torsion testing isothermally at 675 °C after air cooling from 1250 °C. The ferrite was observed to form intragranularly beyond a von Mises equivalent tensile strain of approximately 0.7 to 0.8 and the number fraction of intragranular ferrite grains continued to increase as the strain level increased. Ferrite nucleated to form parallel and closely spaced linear arrays or “rafts” of many discrete ultrafine ferrite grains. It is shown that ferrite nucleates during deformation on defects developed within the austenite parallel to the macroscopic shear direction (i.e., dynamic strain-induced transformation). A model austenitic Ni-30Fe alloy was used to study the substructure developed in the austenite under similar test conditions as that used to induce intragranular ferrite in the steel. It is shown that the most prevalent features developed during testing are microbands. It is proposed that high-energy jogged regions surrounding intersecting microbands provide potential sites for ferrite nucleation at lower strains, while at higher strains, the walls of the microbands may also act as nucleation sites.

A physical based modeling approach for the dynamic behavior of ultrafine grained structures

This paper discusses some experimental results on the influence of grain refinement on the final mechanical properties of IF and microalloyed steels designed for auto-body components. It shows also some modeling approaches to understanding the dynamic behavior of fine-rained materials. The Zerilli–Armstrong (Z–A) and Khan–Huang–Liang (KHL) models for studied steels were implemented into FEM code in order to simulate the dynamic compression tests with different strain rates.

Migraine particles

A hand drawn film dedicated to Len Lye.

Tensile deformation of a ultrafine-grained aluminium alloy: micro shear banding and grain boundary sliding

This work investigates the relationship between the strain rate and the ductility and the underlying deformation mechanisms in an ultrafine-grained Al6082 alloy. At room temperature the uniform elongation of the material exhibits a marked increase with decreasing strain rate. This effect is related to the activation of micro shear banding, which is controlled by grain boundary sliding. The contribution of these mechanisms to uniform elongation is estimated. It is proposed that the grain boundary sliding suppresses the transformation of micro shear bands into macro shear bands. The activity of other deformation mechanisms during plastic deformation of the ultrafine-grained material is also discussed.

A descriptive model for the formation of ultrafine grained steels

This paper presents a descriptive model to explain the mechanisms involved in the development of ultrafine grained structure in steels through dynamic strain induced transformation. The model considers the microstructural evolution during and after deformation as well as the role of different process variables. A key factor is the competition between nucleation and growth, where it is shown that many potential nuclei can be lost under certain conditions leading to a mixed or coarser grain size.

Electroless synthesis of nano-structured gold particles using conducting polymer nanoparticles

In this study, gold nanoparticles were synthesized by electroless recovery of [AuCl4]− from an acidic aqueous solution using nano-structured conducting polymer, polypyrrole nanoparticles, as active surface. The formation of gold nanoparticles was confirmed by TEM, SEM and EDX measurements. The effects of the initial Au(III) concentration on the gold uptake was examined. The recovery capability and gold particle morphology prepared from polypyrrole nanoparticle were compared to that from cast PPy film counterpart.

Formation of ultrafine ferrite by dynamic strain-induced transformation

In the current study, the role of dynamic strain induced transformation on ferrite grain refinement was investigated using different thermomechanical processing routes. A Ni-30Fe austenitic model alloy was also employed to study the evolution of the deformation structure under different deformation conditions. It was shown that the extreme refinement of ferrite is more likely due to the formation of extensive high angle intragranular defects in the austenite through deformation. Among the different thermomechanical parameters, the deformation temperature had a significant effect on the intragranular defect characteristics. There was a transition where the cell dislocation structure changed to laminar microband structures with a decrease in the deformation temperature. Moreover, the ultrafine grained structure was also successfully produced through static transformation using warm deformation process; in other words, concurrent deformation and transformation are not necessary for ultrafine ferrite formation.

Optical microsensor for counting food substance particles in lab-on-a-chips

Integrated optical detection is considered to be an important operation in lab-on-a-chips. This paper presents an optical fiber-based micro-sensor that is capable of detecting food substance particles in a lab-on-a-chip. The system consists of a microcontroller and associated circuitry, a laser emitter, a laser receiver, fiber optic cables, a microfluidics chip, and the food substance samples to be tested. When the particles flow through the microfluidic channel in the chip, the receiver’s output voltage varies due to the particles blocking the passage of the laser ray. The changes in the collected signals are analyzed to count the number of particles. Experiments are conducted on several food substance samples including talcum powder, ground ginger, and soy sauce. The experimental results are presented and discussed.

Thermodynamic and kinetic modelling hydrogenation of titanium particles and sheets

Use of hydrogen as a temporary alloying element in titanium alloys is an attractive approach to improve the mechanical properties of the materials, enhance processability and thereby reduce manufacturing costs. In this paper, the hydrogen diffusion process and the phase transformation both between titanium particles and in titanium sheets were computationally simulated to analyze the mechanism of hydrogen diffusion in different phases (α-Ti, β-Ti and TiHx). With the simulation based on the thermodynamics and kinetics, quantitative behaviors of the hydrogen diffusion and the phase transformation were analyzed. The simulation results provide an insight into the diffusion process and improve the fundamental understanding of the mechanism of diffusion and phase transformation.

UV-shielding ceramic nanoparticles synthesised by mechanochemcial processing

ZnO, TiO₂ and CeO₂ are known as UV-shielding ceramic materials that have advantages over organic UV absorbers for their photo-stability and non-hazardous nature to human bodies. However, they normally cause low transparency in the visible-light range due to light scattering by large particles, which is undesirable for many transparent UV-blocking applications in cosmetic and plastic industries. Light-scattering efficiency of particles can be drastically reduced by decreasing the particle sizes down below 100 nm. This paper reviews recent investigation on the synthesis of ZnO and CeO₂ nanoparticles by mechanochemical processing. The resulting particles had a significantly low degree of agglomeration, having mean particle sizes of ~ 25 nm and ~ 10 nm, respectively. The aqueous suspensions of the nanoparticles showed strong absorption in the UV-light range and high transmittance in the visible-light range. Mechanochemical processing offers the possibility of industrial-scale production of transparent UV-shielding ceramic particles for many applications.

A novel approach for real mass transformation from V2O5 particles to nanorods

A solid-state, mass-quantity transformation from V2O5 powders to nanorods has been realized via a two-step approach. The nanorods were formed through a controlled nanoscale growth from the nanocrystalline V2O5 phase created by a ball milling treatment. The nanorods grow along the [010] direction and are dominated by {001} surfaces. Surface energy minimization and surface diffusion play important roles in their growth mechanism. Real large quantity production can be achieved when the annealing process is conducted in a fluidized bed which can treat large quantities of the milled materials at once. The crystal orientation of nanorods provides an improved cycling stability for lithium intercalation.

Comparative structural analyses of purified glycogen particles from rat liver, human skeletal muscle and commercial preparations

Glycogen is a cellular energy store that is crucial for whole body energy metabolism, metabolic regulation and exercise performance. To understand glycogen structure we have purified glycogen particles from rat liver and human skeletal muscle tissues and compared their biophysical properties with those found in commercial glycogen preparations. Ultrastructural analysis of commercial liver glycogens fails to reveal the classical α-rosette structure but small irregularly shaped particles. In contrast, commercial slipper limpet glycogen consists of β-particles with similar branching and chain lengths to purified rat liver glycogen together with a tendency to form small α-particles, and suggest it should be used as a source of glycogen for all future studies requiring a substitute for mammalian liver glycogen.